linux/Documentation/driver-api/thermal/cpu-cooling-api.rst

108 lines
3.9 KiB
ReStructuredText

=======================
CPU cooling APIs How To
=======================
Written by Amit Daniel Kachhap <amit.kachhap@linaro.org>
Updated: 6 Jan 2015
Copyright (c) 2012 Samsung Electronics Co., Ltd(http://www.samsung.com)
0. Introduction
===============
The generic cpu cooling(freq clipping) provides registration/unregistration APIs
to the caller. The binding of the cooling devices to the trip point is left for
the user. The registration APIs returns the cooling device pointer.
1. cpu cooling APIs
===================
1.1 cpufreq registration/unregistration APIs
--------------------------------------------
::
struct thermal_cooling_device
*cpufreq_cooling_register(struct cpumask *clip_cpus)
This interface function registers the cpufreq cooling device with the name
"thermal-cpufreq-%x". This api can support multiple instances of cpufreq
cooling devices.
clip_cpus:
cpumask of cpus where the frequency constraints will happen.
::
struct thermal_cooling_device
*of_cpufreq_cooling_register(struct cpufreq_policy *policy)
This interface function registers the cpufreq cooling device with
the name "thermal-cpufreq-%x" linking it with a device tree node, in
order to bind it via the thermal DT code. This api can support multiple
instances of cpufreq cooling devices.
policy:
CPUFreq policy.
::
void cpufreq_cooling_unregister(struct thermal_cooling_device *cdev)
This interface function unregisters the "thermal-cpufreq-%x" cooling device.
cdev: Cooling device pointer which has to be unregistered.
2. Power models
===============
The power API registration functions provide a simple power model for
CPUs. The current power is calculated as dynamic power (static power isn't
supported currently). This power model requires that the operating-points of
the CPUs are registered using the kernel's opp library and the
`cpufreq_frequency_table` is assigned to the `struct device` of the
cpu. If you are using CONFIG_CPUFREQ_DT then the
`cpufreq_frequency_table` should already be assigned to the cpu
device.
The dynamic power consumption of a processor depends on many factors.
For a given processor implementation the primary factors are:
- The time the processor spends running, consuming dynamic power, as
compared to the time in idle states where dynamic consumption is
negligible. Herein we refer to this as 'utilisation'.
- The voltage and frequency levels as a result of DVFS. The DVFS
level is a dominant factor governing power consumption.
- In running time the 'execution' behaviour (instruction types, memory
access patterns and so forth) causes, in most cases, a second order
variation. In pathological cases this variation can be significant,
but typically it is of a much lesser impact than the factors above.
A high level dynamic power consumption model may then be represented as::
Pdyn = f(run) * Voltage^2 * Frequency * Utilisation
f(run) here represents the described execution behaviour and its
result has a units of Watts/Hz/Volt^2 (this often expressed in
mW/MHz/uVolt^2)
The detailed behaviour for f(run) could be modelled on-line. However,
in practice, such an on-line model has dependencies on a number of
implementation specific processor support and characterisation
factors. Therefore, in initial implementation that contribution is
represented as a constant coefficient. This is a simplification
consistent with the relative contribution to overall power variation.
In this simplified representation our model becomes::
Pdyn = Capacitance * Voltage^2 * Frequency * Utilisation
Where `capacitance` is a constant that represents an indicative
running time dynamic power coefficient in fundamental units of
mW/MHz/uVolt^2. Typical values for mobile CPUs might lie in range
from 100 to 500. For reference, the approximate values for the SoC in
ARM's Juno Development Platform are 530 for the Cortex-A57 cluster and
140 for the Cortex-A53 cluster.