linux/drivers/net/phy/micrel.c

696 lines
19 KiB
C

/*
* drivers/net/phy/micrel.c
*
* Driver for Micrel PHYs
*
* Author: David J. Choi
*
* Copyright (c) 2010-2013 Micrel, Inc.
*
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License as published by the
* Free Software Foundation; either version 2 of the License, or (at your
* option) any later version.
*
* Support : Micrel Phys:
* Giga phys: ksz9021, ksz9031
* 100/10 Phys : ksz8001, ksz8721, ksz8737, ksz8041
* ksz8021, ksz8031, ksz8051,
* ksz8081, ksz8091,
* ksz8061,
* Switch : ksz8873, ksz886x
*/
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/phy.h>
#include <linux/micrel_phy.h>
#include <linux/of.h>
#include <linux/clk.h>
/* Operation Mode Strap Override */
#define MII_KSZPHY_OMSO 0x16
#define KSZPHY_OMSO_B_CAST_OFF (1 << 9)
#define KSZPHY_OMSO_RMII_OVERRIDE (1 << 1)
#define KSZPHY_OMSO_MII_OVERRIDE (1 << 0)
/* general Interrupt control/status reg in vendor specific block. */
#define MII_KSZPHY_INTCS 0x1B
#define KSZPHY_INTCS_JABBER (1 << 15)
#define KSZPHY_INTCS_RECEIVE_ERR (1 << 14)
#define KSZPHY_INTCS_PAGE_RECEIVE (1 << 13)
#define KSZPHY_INTCS_PARELLEL (1 << 12)
#define KSZPHY_INTCS_LINK_PARTNER_ACK (1 << 11)
#define KSZPHY_INTCS_LINK_DOWN (1 << 10)
#define KSZPHY_INTCS_REMOTE_FAULT (1 << 9)
#define KSZPHY_INTCS_LINK_UP (1 << 8)
#define KSZPHY_INTCS_ALL (KSZPHY_INTCS_LINK_UP |\
KSZPHY_INTCS_LINK_DOWN)
/* general PHY control reg in vendor specific block. */
#define MII_KSZPHY_CTRL 0x1F
/* bitmap of PHY register to set interrupt mode */
#define KSZPHY_CTRL_INT_ACTIVE_HIGH (1 << 9)
#define KSZ9021_CTRL_INT_ACTIVE_HIGH (1 << 14)
#define KS8737_CTRL_INT_ACTIVE_HIGH (1 << 14)
#define KSZ8051_RMII_50MHZ_CLK (1 << 7)
/* Write/read to/from extended registers */
#define MII_KSZPHY_EXTREG 0x0b
#define KSZPHY_EXTREG_WRITE 0x8000
#define MII_KSZPHY_EXTREG_WRITE 0x0c
#define MII_KSZPHY_EXTREG_READ 0x0d
/* Extended registers */
#define MII_KSZPHY_CLK_CONTROL_PAD_SKEW 0x104
#define MII_KSZPHY_RX_DATA_PAD_SKEW 0x105
#define MII_KSZPHY_TX_DATA_PAD_SKEW 0x106
#define PS_TO_REG 200
static int ksz_config_flags(struct phy_device *phydev)
{
int regval;
if (phydev->dev_flags & (MICREL_PHY_50MHZ_CLK | MICREL_PHY_25MHZ_CLK)) {
regval = phy_read(phydev, MII_KSZPHY_CTRL);
if (phydev->dev_flags & MICREL_PHY_50MHZ_CLK)
regval |= KSZ8051_RMII_50MHZ_CLK;
else
regval &= ~KSZ8051_RMII_50MHZ_CLK;
return phy_write(phydev, MII_KSZPHY_CTRL, regval);
}
return 0;
}
static int kszphy_extended_write(struct phy_device *phydev,
u32 regnum, u16 val)
{
phy_write(phydev, MII_KSZPHY_EXTREG, KSZPHY_EXTREG_WRITE | regnum);
return phy_write(phydev, MII_KSZPHY_EXTREG_WRITE, val);
}
static int kszphy_extended_read(struct phy_device *phydev,
u32 regnum)
{
phy_write(phydev, MII_KSZPHY_EXTREG, regnum);
return phy_read(phydev, MII_KSZPHY_EXTREG_READ);
}
static int kszphy_ack_interrupt(struct phy_device *phydev)
{
/* bit[7..0] int status, which is a read and clear register. */
int rc;
rc = phy_read(phydev, MII_KSZPHY_INTCS);
return (rc < 0) ? rc : 0;
}
static int kszphy_set_interrupt(struct phy_device *phydev)
{
int temp;
temp = (PHY_INTERRUPT_ENABLED == phydev->interrupts) ?
KSZPHY_INTCS_ALL : 0;
return phy_write(phydev, MII_KSZPHY_INTCS, temp);
}
static int kszphy_config_intr(struct phy_device *phydev)
{
int temp, rc;
/* set the interrupt pin active low */
temp = phy_read(phydev, MII_KSZPHY_CTRL);
temp &= ~KSZPHY_CTRL_INT_ACTIVE_HIGH;
phy_write(phydev, MII_KSZPHY_CTRL, temp);
rc = kszphy_set_interrupt(phydev);
return rc < 0 ? rc : 0;
}
static int ksz9021_config_intr(struct phy_device *phydev)
{
int temp, rc;
/* set the interrupt pin active low */
temp = phy_read(phydev, MII_KSZPHY_CTRL);
temp &= ~KSZ9021_CTRL_INT_ACTIVE_HIGH;
phy_write(phydev, MII_KSZPHY_CTRL, temp);
rc = kszphy_set_interrupt(phydev);
return rc < 0 ? rc : 0;
}
static int ks8737_config_intr(struct phy_device *phydev)
{
int temp, rc;
/* set the interrupt pin active low */
temp = phy_read(phydev, MII_KSZPHY_CTRL);
temp &= ~KS8737_CTRL_INT_ACTIVE_HIGH;
phy_write(phydev, MII_KSZPHY_CTRL, temp);
rc = kszphy_set_interrupt(phydev);
return rc < 0 ? rc : 0;
}
static int kszphy_setup_led(struct phy_device *phydev,
unsigned int reg, unsigned int shift)
{
struct device *dev = &phydev->dev;
struct device_node *of_node = dev->of_node;
int rc, temp;
u32 val;
if (!of_node && dev->parent->of_node)
of_node = dev->parent->of_node;
if (of_property_read_u32(of_node, "micrel,led-mode", &val))
return 0;
temp = phy_read(phydev, reg);
if (temp < 0)
return temp;
temp &= ~(3 << shift);
temp |= val << shift;
rc = phy_write(phydev, reg, temp);
return rc < 0 ? rc : 0;
}
static int kszphy_config_init(struct phy_device *phydev)
{
return 0;
}
static int kszphy_config_init_led8041(struct phy_device *phydev)
{
/* single led control, register 0x1e bits 15..14 */
return kszphy_setup_led(phydev, 0x1e, 14);
}
static int ksz8021_config_init(struct phy_device *phydev)
{
const u16 val = KSZPHY_OMSO_B_CAST_OFF | KSZPHY_OMSO_RMII_OVERRIDE;
int rc;
rc = kszphy_setup_led(phydev, 0x1f, 4);
if (rc)
dev_err(&phydev->dev, "failed to set led mode\n");
rc = ksz_config_flags(phydev);
if (rc < 0)
return rc;
rc = phy_write(phydev, MII_KSZPHY_OMSO, val);
return rc < 0 ? rc : 0;
}
static int ks8051_config_init(struct phy_device *phydev)
{
int rc;
rc = kszphy_setup_led(phydev, 0x1f, 4);
if (rc)
dev_err(&phydev->dev, "failed to set led mode\n");
rc = ksz_config_flags(phydev);
return rc < 0 ? rc : 0;
}
static int ksz9021_load_values_from_of(struct phy_device *phydev,
struct device_node *of_node, u16 reg,
char *field1, char *field2,
char *field3, char *field4)
{
int val1 = -1;
int val2 = -2;
int val3 = -3;
int val4 = -4;
int newval;
int matches = 0;
if (!of_property_read_u32(of_node, field1, &val1))
matches++;
if (!of_property_read_u32(of_node, field2, &val2))
matches++;
if (!of_property_read_u32(of_node, field3, &val3))
matches++;
if (!of_property_read_u32(of_node, field4, &val4))
matches++;
if (!matches)
return 0;
if (matches < 4)
newval = kszphy_extended_read(phydev, reg);
else
newval = 0;
if (val1 != -1)
newval = ((newval & 0xfff0) | ((val1 / PS_TO_REG) & 0xf) << 0);
if (val2 != -2)
newval = ((newval & 0xff0f) | ((val2 / PS_TO_REG) & 0xf) << 4);
if (val3 != -3)
newval = ((newval & 0xf0ff) | ((val3 / PS_TO_REG) & 0xf) << 8);
if (val4 != -4)
newval = ((newval & 0x0fff) | ((val4 / PS_TO_REG) & 0xf) << 12);
return kszphy_extended_write(phydev, reg, newval);
}
static int ksz9021_config_init(struct phy_device *phydev)
{
struct device *dev = &phydev->dev;
struct device_node *of_node = dev->of_node;
if (!of_node && dev->parent->of_node)
of_node = dev->parent->of_node;
if (of_node) {
ksz9021_load_values_from_of(phydev, of_node,
MII_KSZPHY_CLK_CONTROL_PAD_SKEW,
"txen-skew-ps", "txc-skew-ps",
"rxdv-skew-ps", "rxc-skew-ps");
ksz9021_load_values_from_of(phydev, of_node,
MII_KSZPHY_RX_DATA_PAD_SKEW,
"rxd0-skew-ps", "rxd1-skew-ps",
"rxd2-skew-ps", "rxd3-skew-ps");
ksz9021_load_values_from_of(phydev, of_node,
MII_KSZPHY_TX_DATA_PAD_SKEW,
"txd0-skew-ps", "txd1-skew-ps",
"txd2-skew-ps", "txd3-skew-ps");
}
return 0;
}
#define MII_KSZ9031RN_MMD_CTRL_REG 0x0d
#define MII_KSZ9031RN_MMD_REGDATA_REG 0x0e
#define OP_DATA 1
#define KSZ9031_PS_TO_REG 60
/* Extended registers */
#define MII_KSZ9031RN_CONTROL_PAD_SKEW 4
#define MII_KSZ9031RN_RX_DATA_PAD_SKEW 5
#define MII_KSZ9031RN_TX_DATA_PAD_SKEW 6
#define MII_KSZ9031RN_CLK_PAD_SKEW 8
static int ksz9031_extended_write(struct phy_device *phydev,
u8 mode, u32 dev_addr, u32 regnum, u16 val)
{
phy_write(phydev, MII_KSZ9031RN_MMD_CTRL_REG, dev_addr);
phy_write(phydev, MII_KSZ9031RN_MMD_REGDATA_REG, regnum);
phy_write(phydev, MII_KSZ9031RN_MMD_CTRL_REG, (mode << 14) | dev_addr);
return phy_write(phydev, MII_KSZ9031RN_MMD_REGDATA_REG, val);
}
static int ksz9031_extended_read(struct phy_device *phydev,
u8 mode, u32 dev_addr, u32 regnum)
{
phy_write(phydev, MII_KSZ9031RN_MMD_CTRL_REG, dev_addr);
phy_write(phydev, MII_KSZ9031RN_MMD_REGDATA_REG, regnum);
phy_write(phydev, MII_KSZ9031RN_MMD_CTRL_REG, (mode << 14) | dev_addr);
return phy_read(phydev, MII_KSZ9031RN_MMD_REGDATA_REG);
}
static int ksz9031_of_load_skew_values(struct phy_device *phydev,
struct device_node *of_node,
u16 reg, size_t field_sz,
char *field[], u8 numfields)
{
int val[4] = {-1, -2, -3, -4};
int matches = 0;
u16 mask;
u16 maxval;
u16 newval;
int i;
for (i = 0; i < numfields; i++)
if (!of_property_read_u32(of_node, field[i], val + i))
matches++;
if (!matches)
return 0;
if (matches < numfields)
newval = ksz9031_extended_read(phydev, OP_DATA, 2, reg);
else
newval = 0;
maxval = (field_sz == 4) ? 0xf : 0x1f;
for (i = 0; i < numfields; i++)
if (val[i] != -(i + 1)) {
mask = 0xffff;
mask ^= maxval << (field_sz * i);
newval = (newval & mask) |
(((val[i] / KSZ9031_PS_TO_REG) & maxval)
<< (field_sz * i));
}
return ksz9031_extended_write(phydev, OP_DATA, 2, reg, newval);
}
static int ksz9031_config_init(struct phy_device *phydev)
{
struct device *dev = &phydev->dev;
struct device_node *of_node = dev->of_node;
char *clk_skews[2] = {"rxc-skew-ps", "txc-skew-ps"};
char *rx_data_skews[4] = {
"rxd0-skew-ps", "rxd1-skew-ps",
"rxd2-skew-ps", "rxd3-skew-ps"
};
char *tx_data_skews[4] = {
"txd0-skew-ps", "txd1-skew-ps",
"txd2-skew-ps", "txd3-skew-ps"
};
char *control_skews[2] = {"txen-skew-ps", "rxdv-skew-ps"};
if (!of_node && dev->parent->of_node)
of_node = dev->parent->of_node;
if (of_node) {
ksz9031_of_load_skew_values(phydev, of_node,
MII_KSZ9031RN_CLK_PAD_SKEW, 5,
clk_skews, 2);
ksz9031_of_load_skew_values(phydev, of_node,
MII_KSZ9031RN_CONTROL_PAD_SKEW, 4,
control_skews, 2);
ksz9031_of_load_skew_values(phydev, of_node,
MII_KSZ9031RN_RX_DATA_PAD_SKEW, 4,
rx_data_skews, 4);
ksz9031_of_load_skew_values(phydev, of_node,
MII_KSZ9031RN_TX_DATA_PAD_SKEW, 4,
tx_data_skews, 4);
}
return 0;
}
#define KSZ8873MLL_GLOBAL_CONTROL_4 0x06
#define KSZ8873MLL_GLOBAL_CONTROL_4_DUPLEX (1 << 6)
#define KSZ8873MLL_GLOBAL_CONTROL_4_SPEED (1 << 4)
static int ksz8873mll_read_status(struct phy_device *phydev)
{
int regval;
/* dummy read */
regval = phy_read(phydev, KSZ8873MLL_GLOBAL_CONTROL_4);
regval = phy_read(phydev, KSZ8873MLL_GLOBAL_CONTROL_4);
if (regval & KSZ8873MLL_GLOBAL_CONTROL_4_DUPLEX)
phydev->duplex = DUPLEX_HALF;
else
phydev->duplex = DUPLEX_FULL;
if (regval & KSZ8873MLL_GLOBAL_CONTROL_4_SPEED)
phydev->speed = SPEED_10;
else
phydev->speed = SPEED_100;
phydev->link = 1;
phydev->pause = phydev->asym_pause = 0;
return 0;
}
static int ksz8873mll_config_aneg(struct phy_device *phydev)
{
return 0;
}
/* This routine returns -1 as an indication to the caller that the
* Micrel ksz9021 10/100/1000 PHY does not support standard IEEE
* MMD extended PHY registers.
*/
static int
ksz9021_rd_mmd_phyreg(struct phy_device *phydev, int ptrad, int devnum,
int regnum)
{
return -1;
}
/* This routine does nothing since the Micrel ksz9021 does not support
* standard IEEE MMD extended PHY registers.
*/
static void
ksz9021_wr_mmd_phyreg(struct phy_device *phydev, int ptrad, int devnum,
int regnum, u32 val)
{
}
static int ksz8021_probe(struct phy_device *phydev)
{
struct clk *clk;
clk = devm_clk_get(&phydev->dev, "rmii-ref");
if (!IS_ERR(clk)) {
unsigned long rate = clk_get_rate(clk);
if (rate > 24500000 && rate < 25500000) {
phydev->dev_flags |= MICREL_PHY_25MHZ_CLK;
} else if (rate > 49500000 && rate < 50500000) {
phydev->dev_flags |= MICREL_PHY_50MHZ_CLK;
} else {
dev_err(&phydev->dev, "Clock rate out of range: %ld\n", rate);
return -EINVAL;
}
}
return 0;
}
static struct phy_driver ksphy_driver[] = {
{
.phy_id = PHY_ID_KS8737,
.phy_id_mask = 0x00fffff0,
.name = "Micrel KS8737",
.features = (PHY_BASIC_FEATURES | SUPPORTED_Pause),
.flags = PHY_HAS_MAGICANEG | PHY_HAS_INTERRUPT,
.config_init = kszphy_config_init,
.config_aneg = genphy_config_aneg,
.read_status = genphy_read_status,
.ack_interrupt = kszphy_ack_interrupt,
.config_intr = ks8737_config_intr,
.suspend = genphy_suspend,
.resume = genphy_resume,
.driver = { .owner = THIS_MODULE,},
}, {
.phy_id = PHY_ID_KSZ8021,
.phy_id_mask = 0x00ffffff,
.name = "Micrel KSZ8021 or KSZ8031",
.features = (PHY_BASIC_FEATURES | SUPPORTED_Pause |
SUPPORTED_Asym_Pause),
.flags = PHY_HAS_MAGICANEG | PHY_HAS_INTERRUPT,
.probe = ksz8021_probe,
.config_init = ksz8021_config_init,
.config_aneg = genphy_config_aneg,
.read_status = genphy_read_status,
.ack_interrupt = kszphy_ack_interrupt,
.config_intr = kszphy_config_intr,
.suspend = genphy_suspend,
.resume = genphy_resume,
.driver = { .owner = THIS_MODULE,},
}, {
.phy_id = PHY_ID_KSZ8031,
.phy_id_mask = 0x00ffffff,
.name = "Micrel KSZ8031",
.features = (PHY_BASIC_FEATURES | SUPPORTED_Pause |
SUPPORTED_Asym_Pause),
.flags = PHY_HAS_MAGICANEG | PHY_HAS_INTERRUPT,
.probe = ksz8021_probe,
.config_init = ksz8021_config_init,
.config_aneg = genphy_config_aneg,
.read_status = genphy_read_status,
.ack_interrupt = kszphy_ack_interrupt,
.config_intr = kszphy_config_intr,
.suspend = genphy_suspend,
.resume = genphy_resume,
.driver = { .owner = THIS_MODULE,},
}, {
.phy_id = PHY_ID_KSZ8041,
.phy_id_mask = 0x00fffff0,
.name = "Micrel KSZ8041",
.features = (PHY_BASIC_FEATURES | SUPPORTED_Pause
| SUPPORTED_Asym_Pause),
.flags = PHY_HAS_MAGICANEG | PHY_HAS_INTERRUPT,
.config_init = kszphy_config_init_led8041,
.config_aneg = genphy_config_aneg,
.read_status = genphy_read_status,
.ack_interrupt = kszphy_ack_interrupt,
.config_intr = kszphy_config_intr,
.suspend = genphy_suspend,
.resume = genphy_resume,
.driver = { .owner = THIS_MODULE,},
}, {
.phy_id = PHY_ID_KSZ8041RNLI,
.phy_id_mask = 0x00fffff0,
.name = "Micrel KSZ8041RNLI",
.features = PHY_BASIC_FEATURES |
SUPPORTED_Pause | SUPPORTED_Asym_Pause,
.flags = PHY_HAS_MAGICANEG | PHY_HAS_INTERRUPT,
.config_init = kszphy_config_init_led8041,
.config_aneg = genphy_config_aneg,
.read_status = genphy_read_status,
.ack_interrupt = kszphy_ack_interrupt,
.config_intr = kszphy_config_intr,
.suspend = genphy_suspend,
.resume = genphy_resume,
.driver = { .owner = THIS_MODULE,},
}, {
.phy_id = PHY_ID_KSZ8051,
.phy_id_mask = 0x00fffff0,
.name = "Micrel KSZ8051",
.features = (PHY_BASIC_FEATURES | SUPPORTED_Pause
| SUPPORTED_Asym_Pause),
.flags = PHY_HAS_MAGICANEG | PHY_HAS_INTERRUPT,
.config_init = ks8051_config_init,
.config_aneg = genphy_config_aneg,
.read_status = genphy_read_status,
.ack_interrupt = kszphy_ack_interrupt,
.config_intr = kszphy_config_intr,
.suspend = genphy_suspend,
.resume = genphy_resume,
.driver = { .owner = THIS_MODULE,},
}, {
.phy_id = PHY_ID_KSZ8001,
.name = "Micrel KSZ8001 or KS8721",
.phy_id_mask = 0x00ffffff,
.features = (PHY_BASIC_FEATURES | SUPPORTED_Pause),
.flags = PHY_HAS_MAGICANEG | PHY_HAS_INTERRUPT,
.config_init = kszphy_config_init_led8041,
.config_aneg = genphy_config_aneg,
.read_status = genphy_read_status,
.ack_interrupt = kszphy_ack_interrupt,
.config_intr = kszphy_config_intr,
.suspend = genphy_suspend,
.resume = genphy_resume,
.driver = { .owner = THIS_MODULE,},
}, {
.phy_id = PHY_ID_KSZ8081,
.name = "Micrel KSZ8081 or KSZ8091",
.phy_id_mask = 0x00fffff0,
.features = (PHY_BASIC_FEATURES | SUPPORTED_Pause),
.flags = PHY_HAS_MAGICANEG | PHY_HAS_INTERRUPT,
.config_init = kszphy_config_init,
.config_aneg = genphy_config_aneg,
.read_status = genphy_read_status,
.ack_interrupt = kszphy_ack_interrupt,
.config_intr = kszphy_config_intr,
.suspend = genphy_suspend,
.resume = genphy_resume,
.driver = { .owner = THIS_MODULE,},
}, {
.phy_id = PHY_ID_KSZ8061,
.name = "Micrel KSZ8061",
.phy_id_mask = 0x00fffff0,
.features = (PHY_BASIC_FEATURES | SUPPORTED_Pause),
.flags = PHY_HAS_MAGICANEG | PHY_HAS_INTERRUPT,
.config_init = kszphy_config_init,
.config_aneg = genphy_config_aneg,
.read_status = genphy_read_status,
.ack_interrupt = kszphy_ack_interrupt,
.config_intr = kszphy_config_intr,
.suspend = genphy_suspend,
.resume = genphy_resume,
.driver = { .owner = THIS_MODULE,},
}, {
.phy_id = PHY_ID_KSZ9021,
.phy_id_mask = 0x000ffffe,
.name = "Micrel KSZ9021 Gigabit PHY",
.features = (PHY_GBIT_FEATURES | SUPPORTED_Pause),
.flags = PHY_HAS_MAGICANEG | PHY_HAS_INTERRUPT,
.config_init = ksz9021_config_init,
.config_aneg = genphy_config_aneg,
.read_status = genphy_read_status,
.ack_interrupt = kszphy_ack_interrupt,
.config_intr = ksz9021_config_intr,
.suspend = genphy_suspend,
.resume = genphy_resume,
.read_mmd_indirect = ksz9021_rd_mmd_phyreg,
.write_mmd_indirect = ksz9021_wr_mmd_phyreg,
.driver = { .owner = THIS_MODULE, },
}, {
.phy_id = PHY_ID_KSZ9031,
.phy_id_mask = 0x00fffff0,
.name = "Micrel KSZ9031 Gigabit PHY",
.features = (PHY_GBIT_FEATURES | SUPPORTED_Pause),
.flags = PHY_HAS_MAGICANEG | PHY_HAS_INTERRUPT,
.config_init = ksz9031_config_init,
.config_aneg = genphy_config_aneg,
.read_status = genphy_read_status,
.ack_interrupt = kszphy_ack_interrupt,
.config_intr = ksz9021_config_intr,
.suspend = genphy_suspend,
.resume = genphy_resume,
.driver = { .owner = THIS_MODULE, },
}, {
.phy_id = PHY_ID_KSZ8873MLL,
.phy_id_mask = 0x00fffff0,
.name = "Micrel KSZ8873MLL Switch",
.features = (SUPPORTED_Pause | SUPPORTED_Asym_Pause),
.flags = PHY_HAS_MAGICANEG,
.config_init = kszphy_config_init,
.config_aneg = ksz8873mll_config_aneg,
.read_status = ksz8873mll_read_status,
.suspend = genphy_suspend,
.resume = genphy_resume,
.driver = { .owner = THIS_MODULE, },
}, {
.phy_id = PHY_ID_KSZ886X,
.phy_id_mask = 0x00fffff0,
.name = "Micrel KSZ886X Switch",
.features = (PHY_BASIC_FEATURES | SUPPORTED_Pause),
.flags = PHY_HAS_MAGICANEG | PHY_HAS_INTERRUPT,
.config_init = kszphy_config_init,
.config_aneg = genphy_config_aneg,
.read_status = genphy_read_status,
.suspend = genphy_suspend,
.resume = genphy_resume,
.driver = { .owner = THIS_MODULE, },
} };
static int __init ksphy_init(void)
{
return phy_drivers_register(ksphy_driver,
ARRAY_SIZE(ksphy_driver));
}
static void __exit ksphy_exit(void)
{
phy_drivers_unregister(ksphy_driver,
ARRAY_SIZE(ksphy_driver));
}
module_init(ksphy_init);
module_exit(ksphy_exit);
MODULE_DESCRIPTION("Micrel PHY driver");
MODULE_AUTHOR("David J. Choi");
MODULE_LICENSE("GPL");
static struct mdio_device_id __maybe_unused micrel_tbl[] = {
{ PHY_ID_KSZ9021, 0x000ffffe },
{ PHY_ID_KSZ9031, 0x00fffff0 },
{ PHY_ID_KSZ8001, 0x00ffffff },
{ PHY_ID_KS8737, 0x00fffff0 },
{ PHY_ID_KSZ8021, 0x00ffffff },
{ PHY_ID_KSZ8031, 0x00ffffff },
{ PHY_ID_KSZ8041, 0x00fffff0 },
{ PHY_ID_KSZ8051, 0x00fffff0 },
{ PHY_ID_KSZ8061, 0x00fffff0 },
{ PHY_ID_KSZ8081, 0x00fffff0 },
{ PHY_ID_KSZ8873MLL, 0x00fffff0 },
{ PHY_ID_KSZ886X, 0x00fffff0 },
{ }
};
MODULE_DEVICE_TABLE(mdio, micrel_tbl);