linux/drivers/usb/dwc3/dwc3-st.c

376 lines
9.8 KiB
C
Raw Blame History

This file contains ambiguous Unicode characters

This file contains Unicode characters that might be confused with other characters. If you think that this is intentional, you can safely ignore this warning. Use the Escape button to reveal them.

// SPDX-License-Identifier: GPL-2.0+
/**
* dwc3-st.c Support for dwc3 platform devices on ST Microelectronics platforms
*
* This is a small driver for the dwc3 to provide the glue logic
* to configure the controller. Tested on STi platforms.
*
* Copyright (C) 2014 Stmicroelectronics
*
* Author: Giuseppe Cavallaro <peppe.cavallaro@st.com>
* Contributors: Aymen Bouattay <aymen.bouattay@st.com>
* Peter Griffin <peter.griffin@linaro.org>
*
* Inspired by dwc3-omap.c and dwc3-exynos.c.
*/
#include <linux/delay.h>
#include <linux/interrupt.h>
#include <linux/io.h>
#include <linux/ioport.h>
#include <linux/kernel.h>
#include <linux/mfd/syscon.h>
#include <linux/module.h>
#include <linux/of.h>
#include <linux/of_platform.h>
#include <linux/platform_device.h>
#include <linux/slab.h>
#include <linux/regmap.h>
#include <linux/reset.h>
#include <linux/pinctrl/consumer.h>
#include <linux/usb/of.h>
#include "core.h"
#include "io.h"
/* glue registers */
#define CLKRST_CTRL 0x00
#define AUX_CLK_EN BIT(0)
#define SW_PIPEW_RESET_N BIT(4)
#define EXT_CFG_RESET_N BIT(8)
/*
* 1'b0 : The host controller complies with the xHCI revision 0.96
* 1'b1 : The host controller complies with the xHCI revision 1.0
*/
#define XHCI_REVISION BIT(12)
#define USB2_VBUS_MNGMNT_SEL1 0x2C
/*
* For all fields in USB2_VBUS_MNGMNT_SEL1
* 2b00 : Override value from Reg 0x30 is selected
* 2b01 : utmiotg_<signal_name> from usb3_top is selected
* 2b10 : pipew_<signal_name> from PIPEW instance is selected
* 2b11 : value is 1'b0
*/
#define USB2_VBUS_REG30 0x0
#define USB2_VBUS_UTMIOTG 0x1
#define USB2_VBUS_PIPEW 0x2
#define USB2_VBUS_ZERO 0x3
#define SEL_OVERRIDE_VBUSVALID(n) (n << 0)
#define SEL_OVERRIDE_POWERPRESENT(n) (n << 4)
#define SEL_OVERRIDE_BVALID(n) (n << 8)
/* Static DRD configuration */
#define USB3_CONTROL_MASK 0xf77
#define USB3_DEVICE_NOT_HOST BIT(0)
#define USB3_FORCE_VBUSVALID BIT(1)
#define USB3_DELAY_VBUSVALID BIT(2)
#define USB3_SEL_FORCE_OPMODE BIT(4)
#define USB3_FORCE_OPMODE(n) (n << 5)
#define USB3_SEL_FORCE_DPPULLDOWN2 BIT(8)
#define USB3_FORCE_DPPULLDOWN2 BIT(9)
#define USB3_SEL_FORCE_DMPULLDOWN2 BIT(10)
#define USB3_FORCE_DMPULLDOWN2 BIT(11)
/**
* struct st_dwc3 - dwc3-st driver private structure
* @dev: device pointer
* @glue_base: ioaddr for the glue registers
* @regmap: regmap pointer for getting syscfg
* @syscfg_reg_off: usb syscfg control offset
* @dr_mode: drd static host/device config
* @rstc_pwrdn: rest controller for powerdown signal
* @rstc_rst: reset controller for softreset signal
*/
struct st_dwc3 {
struct device *dev;
void __iomem *glue_base;
struct regmap *regmap;
int syscfg_reg_off;
enum usb_dr_mode dr_mode;
struct reset_control *rstc_pwrdn;
struct reset_control *rstc_rst;
};
static inline u32 st_dwc3_readl(void __iomem *base, u32 offset)
{
return readl_relaxed(base + offset);
}
static inline void st_dwc3_writel(void __iomem *base, u32 offset, u32 value)
{
writel_relaxed(value, base + offset);
}
/**
* st_dwc3_drd_init: program the port
* @dwc3_data: driver private structure
* Description: this function is to program the port as either host or device
* according to the static configuration passed from devicetree.
* OTG and dual role are not yet supported!
*/
static int st_dwc3_drd_init(struct st_dwc3 *dwc3_data)
{
u32 val;
int err;
err = regmap_read(dwc3_data->regmap, dwc3_data->syscfg_reg_off, &val);
if (err)
return err;
val &= USB3_CONTROL_MASK;
switch (dwc3_data->dr_mode) {
case USB_DR_MODE_PERIPHERAL:
val &= ~(USB3_DELAY_VBUSVALID
| USB3_SEL_FORCE_OPMODE | USB3_FORCE_OPMODE(0x3)
| USB3_SEL_FORCE_DPPULLDOWN2 | USB3_FORCE_DPPULLDOWN2
| USB3_SEL_FORCE_DMPULLDOWN2 | USB3_FORCE_DMPULLDOWN2);
/*
* USB3_PORT2_FORCE_VBUSVALID When '1' and when
* USB3_PORT2_DEVICE_NOT_HOST = 1, forces VBUSVLDEXT2 input
* of the pico PHY to 1.
*/
val |= USB3_DEVICE_NOT_HOST | USB3_FORCE_VBUSVALID;
break;
case USB_DR_MODE_HOST:
val &= ~(USB3_DEVICE_NOT_HOST | USB3_FORCE_VBUSVALID
| USB3_SEL_FORCE_OPMODE | USB3_FORCE_OPMODE(0x3)
| USB3_SEL_FORCE_DPPULLDOWN2 | USB3_FORCE_DPPULLDOWN2
| USB3_SEL_FORCE_DMPULLDOWN2 | USB3_FORCE_DMPULLDOWN2);
/*
* USB3_DELAY_VBUSVALID is ANDed with USB_C_VBUSVALID. Thus,
* when set to 0, it can delay the arrival of VBUSVALID
* information to VBUSVLDEXT2 input of the pico PHY.
* We don't want to do that so we set the bit to '1'.
*/
val |= USB3_DELAY_VBUSVALID;
break;
default:
dev_err(dwc3_data->dev, "Unsupported mode of operation %d\n",
dwc3_data->dr_mode);
return -EINVAL;
}
return regmap_write(dwc3_data->regmap, dwc3_data->syscfg_reg_off, val);
}
/**
* st_dwc3_init: init the controller via glue logic
* @dwc3_data: driver private structure
*/
static void st_dwc3_init(struct st_dwc3 *dwc3_data)
{
u32 reg = st_dwc3_readl(dwc3_data->glue_base, CLKRST_CTRL);
reg |= AUX_CLK_EN | EXT_CFG_RESET_N | XHCI_REVISION;
reg &= ~SW_PIPEW_RESET_N;
st_dwc3_writel(dwc3_data->glue_base, CLKRST_CTRL, reg);
/* configure mux for vbus, powerpresent and bvalid signals */
reg = st_dwc3_readl(dwc3_data->glue_base, USB2_VBUS_MNGMNT_SEL1);
reg |= SEL_OVERRIDE_VBUSVALID(USB2_VBUS_UTMIOTG) |
SEL_OVERRIDE_POWERPRESENT(USB2_VBUS_UTMIOTG) |
SEL_OVERRIDE_BVALID(USB2_VBUS_UTMIOTG);
st_dwc3_writel(dwc3_data->glue_base, USB2_VBUS_MNGMNT_SEL1, reg);
reg = st_dwc3_readl(dwc3_data->glue_base, CLKRST_CTRL);
reg |= SW_PIPEW_RESET_N;
st_dwc3_writel(dwc3_data->glue_base, CLKRST_CTRL, reg);
}
static int st_dwc3_probe(struct platform_device *pdev)
{
struct st_dwc3 *dwc3_data;
struct resource *res;
struct device *dev = &pdev->dev;
struct device_node *node = dev->of_node, *child;
struct platform_device *child_pdev;
struct regmap *regmap;
int ret;
dwc3_data = devm_kzalloc(dev, sizeof(*dwc3_data), GFP_KERNEL);
if (!dwc3_data)
return -ENOMEM;
res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "reg-glue");
dwc3_data->glue_base = devm_ioremap_resource(dev, res);
if (IS_ERR(dwc3_data->glue_base))
return PTR_ERR(dwc3_data->glue_base);
regmap = syscon_regmap_lookup_by_phandle(node, "st,syscfg");
if (IS_ERR(regmap))
return PTR_ERR(regmap);
dwc3_data->dev = dev;
dwc3_data->regmap = regmap;
res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "syscfg-reg");
if (!res) {
ret = -ENXIO;
goto undo_platform_dev_alloc;
}
dwc3_data->syscfg_reg_off = res->start;
dev_vdbg(&pdev->dev, "glue-logic addr 0x%pK, syscfg-reg offset 0x%x\n",
dwc3_data->glue_base, dwc3_data->syscfg_reg_off);
dwc3_data->rstc_pwrdn =
devm_reset_control_get_exclusive(dev, "powerdown");
if (IS_ERR(dwc3_data->rstc_pwrdn)) {
dev_err(&pdev->dev, "could not get power controller\n");
ret = PTR_ERR(dwc3_data->rstc_pwrdn);
goto undo_platform_dev_alloc;
}
/* Manage PowerDown */
reset_control_deassert(dwc3_data->rstc_pwrdn);
dwc3_data->rstc_rst =
devm_reset_control_get_shared(dev, "softreset");
if (IS_ERR(dwc3_data->rstc_rst)) {
dev_err(&pdev->dev, "could not get reset controller\n");
ret = PTR_ERR(dwc3_data->rstc_rst);
goto undo_powerdown;
}
/* Manage SoftReset */
reset_control_deassert(dwc3_data->rstc_rst);
child = of_get_child_by_name(node, "dwc3");
if (!child) {
dev_err(&pdev->dev, "failed to find dwc3 core node\n");
ret = -ENODEV;
goto undo_softreset;
}
/* Allocate and initialize the core */
ret = of_platform_populate(node, NULL, NULL, dev);
if (ret) {
dev_err(dev, "failed to add dwc3 core\n");
goto undo_softreset;
}
child_pdev = of_find_device_by_node(child);
if (!child_pdev) {
dev_err(dev, "failed to find dwc3 core device\n");
ret = -ENODEV;
goto undo_softreset;
}
dwc3_data->dr_mode = usb_get_dr_mode(&child_pdev->dev);
/*
* Configure the USB port as device or host according to the static
* configuration passed from DT.
* DRD is the only mode currently supported so this will be enhanced
* as soon as OTG is available.
*/
ret = st_dwc3_drd_init(dwc3_data);
if (ret) {
dev_err(dev, "drd initialisation failed\n");
goto undo_softreset;
}
/* ST glue logic init */
st_dwc3_init(dwc3_data);
platform_set_drvdata(pdev, dwc3_data);
return 0;
undo_softreset:
reset_control_assert(dwc3_data->rstc_rst);
undo_powerdown:
reset_control_assert(dwc3_data->rstc_pwrdn);
undo_platform_dev_alloc:
platform_device_put(pdev);
return ret;
}
static int st_dwc3_remove(struct platform_device *pdev)
{
struct st_dwc3 *dwc3_data = platform_get_drvdata(pdev);
of_platform_depopulate(&pdev->dev);
reset_control_assert(dwc3_data->rstc_pwrdn);
reset_control_assert(dwc3_data->rstc_rst);
return 0;
}
#ifdef CONFIG_PM_SLEEP
static int st_dwc3_suspend(struct device *dev)
{
struct st_dwc3 *dwc3_data = dev_get_drvdata(dev);
reset_control_assert(dwc3_data->rstc_pwrdn);
reset_control_assert(dwc3_data->rstc_rst);
pinctrl_pm_select_sleep_state(dev);
return 0;
}
static int st_dwc3_resume(struct device *dev)
{
struct st_dwc3 *dwc3_data = dev_get_drvdata(dev);
int ret;
pinctrl_pm_select_default_state(dev);
reset_control_deassert(dwc3_data->rstc_pwrdn);
reset_control_deassert(dwc3_data->rstc_rst);
ret = st_dwc3_drd_init(dwc3_data);
if (ret) {
dev_err(dev, "drd initialisation failed\n");
return ret;
}
/* ST glue logic init */
st_dwc3_init(dwc3_data);
return 0;
}
#endif /* CONFIG_PM_SLEEP */
static SIMPLE_DEV_PM_OPS(st_dwc3_dev_pm_ops, st_dwc3_suspend, st_dwc3_resume);
static const struct of_device_id st_dwc3_match[] = {
{ .compatible = "st,stih407-dwc3" },
{ /* sentinel */ },
};
MODULE_DEVICE_TABLE(of, st_dwc3_match);
static struct platform_driver st_dwc3_driver = {
.probe = st_dwc3_probe,
.remove = st_dwc3_remove,
.driver = {
.name = "usb-st-dwc3",
.of_match_table = st_dwc3_match,
.pm = &st_dwc3_dev_pm_ops,
},
};
module_platform_driver(st_dwc3_driver);
MODULE_AUTHOR("Giuseppe Cavallaro <peppe.cavallaro@st.com>");
MODULE_DESCRIPTION("DesignWare USB3 STi Glue Layer");
MODULE_LICENSE("GPL v2");