linux/drivers/ata/sata_inic162x.c

780 lines
19 KiB
C

/*
* sata_inic162x.c - Driver for Initio 162x SATA controllers
*
* Copyright 2006 SUSE Linux Products GmbH
* Copyright 2006 Tejun Heo <teheo@novell.com>
*
* This file is released under GPL v2.
*
* This controller is eccentric and easily locks up if something isn't
* right. Documentation is available at initio's website but it only
* documents registers (not programming model).
*
* - ATA disks work.
* - Hotplug works.
* - ATAPI read works but burning doesn't. This thing is really
* peculiar about ATAPI and I couldn't figure out how ATAPI PIO and
* ATAPI DMA WRITE should be programmed. If you've got a clue, be
* my guest.
* - Both STR and STD work.
*/
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/pci.h>
#include <scsi/scsi_host.h>
#include <linux/libata.h>
#include <linux/blkdev.h>
#include <scsi/scsi_device.h>
#define DRV_NAME "sata_inic162x"
#define DRV_VERSION "0.3"
enum {
MMIO_BAR = 5,
NR_PORTS = 2,
HOST_CTL = 0x7c,
HOST_STAT = 0x7e,
HOST_IRQ_STAT = 0xbc,
HOST_IRQ_MASK = 0xbe,
PORT_SIZE = 0x40,
/* registers for ATA TF operation */
PORT_TF = 0x00,
PORT_ALT_STAT = 0x08,
PORT_IRQ_STAT = 0x09,
PORT_IRQ_MASK = 0x0a,
PORT_PRD_CTL = 0x0b,
PORT_PRD_ADDR = 0x0c,
PORT_PRD_XFERLEN = 0x10,
/* IDMA register */
PORT_IDMA_CTL = 0x14,
PORT_SCR = 0x20,
/* HOST_CTL bits */
HCTL_IRQOFF = (1 << 8), /* global IRQ off */
HCTL_PWRDWN = (1 << 13), /* power down PHYs */
HCTL_SOFTRST = (1 << 13), /* global reset (no phy reset) */
HCTL_RPGSEL = (1 << 15), /* register page select */
HCTL_KNOWN_BITS = HCTL_IRQOFF | HCTL_PWRDWN | HCTL_SOFTRST |
HCTL_RPGSEL,
/* HOST_IRQ_(STAT|MASK) bits */
HIRQ_PORT0 = (1 << 0),
HIRQ_PORT1 = (1 << 1),
HIRQ_SOFT = (1 << 14),
HIRQ_GLOBAL = (1 << 15), /* STAT only */
/* PORT_IRQ_(STAT|MASK) bits */
PIRQ_OFFLINE = (1 << 0), /* device unplugged */
PIRQ_ONLINE = (1 << 1), /* device plugged */
PIRQ_COMPLETE = (1 << 2), /* completion interrupt */
PIRQ_FATAL = (1 << 3), /* fatal error */
PIRQ_ATA = (1 << 4), /* ATA interrupt */
PIRQ_REPLY = (1 << 5), /* reply FIFO not empty */
PIRQ_PENDING = (1 << 7), /* port IRQ pending (STAT only) */
PIRQ_ERR = PIRQ_OFFLINE | PIRQ_ONLINE | PIRQ_FATAL,
PIRQ_MASK_DMA_READ = PIRQ_REPLY | PIRQ_ATA,
PIRQ_MASK_OTHER = PIRQ_REPLY | PIRQ_COMPLETE,
PIRQ_MASK_FREEZE = 0xff,
/* PORT_PRD_CTL bits */
PRD_CTL_START = (1 << 0),
PRD_CTL_WR = (1 << 3),
PRD_CTL_DMAEN = (1 << 7), /* DMA enable */
/* PORT_IDMA_CTL bits */
IDMA_CTL_RST_ATA = (1 << 2), /* hardreset ATA bus */
IDMA_CTL_RST_IDMA = (1 << 5), /* reset IDMA machinary */
IDMA_CTL_GO = (1 << 7), /* IDMA mode go */
IDMA_CTL_ATA_NIEN = (1 << 8), /* ATA IRQ disable */
};
struct inic_host_priv {
u16 cached_hctl;
};
struct inic_port_priv {
u8 dfl_prdctl;
u8 cached_prdctl;
u8 cached_pirq_mask;
};
static struct scsi_host_template inic_sht = {
.module = THIS_MODULE,
.name = DRV_NAME,
.ioctl = ata_scsi_ioctl,
.queuecommand = ata_scsi_queuecmd,
.can_queue = ATA_DEF_QUEUE,
.this_id = ATA_SHT_THIS_ID,
.sg_tablesize = LIBATA_MAX_PRD,
.cmd_per_lun = ATA_SHT_CMD_PER_LUN,
.emulated = ATA_SHT_EMULATED,
.use_clustering = ATA_SHT_USE_CLUSTERING,
.proc_name = DRV_NAME,
.dma_boundary = ATA_DMA_BOUNDARY,
.slave_configure = ata_scsi_slave_config,
.slave_destroy = ata_scsi_slave_destroy,
.bios_param = ata_std_bios_param,
};
static const int scr_map[] = {
[SCR_STATUS] = 0,
[SCR_ERROR] = 1,
[SCR_CONTROL] = 2,
};
static void __iomem *inic_port_base(struct ata_port *ap)
{
return ap->host->iomap[MMIO_BAR] + ap->port_no * PORT_SIZE;
}
static void __inic_set_pirq_mask(struct ata_port *ap, u8 mask)
{
void __iomem *port_base = inic_port_base(ap);
struct inic_port_priv *pp = ap->private_data;
writeb(mask, port_base + PORT_IRQ_MASK);
pp->cached_pirq_mask = mask;
}
static void inic_set_pirq_mask(struct ata_port *ap, u8 mask)
{
struct inic_port_priv *pp = ap->private_data;
if (pp->cached_pirq_mask != mask)
__inic_set_pirq_mask(ap, mask);
}
static void inic_reset_port(void __iomem *port_base)
{
void __iomem *idma_ctl = port_base + PORT_IDMA_CTL;
u16 ctl;
ctl = readw(idma_ctl);
ctl &= ~(IDMA_CTL_RST_IDMA | IDMA_CTL_ATA_NIEN | IDMA_CTL_GO);
/* mask IRQ and assert reset */
writew(ctl | IDMA_CTL_RST_IDMA | IDMA_CTL_ATA_NIEN, idma_ctl);
readw(idma_ctl); /* flush */
/* give it some time */
msleep(1);
/* release reset */
writew(ctl | IDMA_CTL_ATA_NIEN, idma_ctl);
/* clear irq */
writeb(0xff, port_base + PORT_IRQ_STAT);
/* reenable ATA IRQ, turn off IDMA mode */
writew(ctl, idma_ctl);
}
static int inic_scr_read(struct ata_port *ap, unsigned sc_reg, u32 *val)
{
void __iomem *scr_addr = ap->ioaddr.scr_addr;
void __iomem *addr;
if (unlikely(sc_reg >= ARRAY_SIZE(scr_map)))
return -EINVAL;
addr = scr_addr + scr_map[sc_reg] * 4;
*val = readl(scr_addr + scr_map[sc_reg] * 4);
/* this controller has stuck DIAG.N, ignore it */
if (sc_reg == SCR_ERROR)
*val &= ~SERR_PHYRDY_CHG;
return 0;
}
static int inic_scr_write(struct ata_port *ap, unsigned sc_reg, u32 val)
{
void __iomem *scr_addr = ap->ioaddr.scr_addr;
void __iomem *addr;
if (unlikely(sc_reg >= ARRAY_SIZE(scr_map)))
return -EINVAL;
addr = scr_addr + scr_map[sc_reg] * 4;
writel(val, scr_addr + scr_map[sc_reg] * 4);
return 0;
}
/*
* In TF mode, inic162x is very similar to SFF device. TF registers
* function the same. DMA engine behaves similary using the same PRD
* format as BMDMA but different command register, interrupt and event
* notification methods are used. The following inic_bmdma_*()
* functions do the impedance matching.
*/
static void inic_bmdma_setup(struct ata_queued_cmd *qc)
{
struct ata_port *ap = qc->ap;
struct inic_port_priv *pp = ap->private_data;
void __iomem *port_base = inic_port_base(ap);
int rw = qc->tf.flags & ATA_TFLAG_WRITE;
/* make sure device sees PRD table writes */
wmb();
/* load transfer length */
writel(qc->nbytes, port_base + PORT_PRD_XFERLEN);
/* turn on DMA and specify data direction */
pp->cached_prdctl = pp->dfl_prdctl | PRD_CTL_DMAEN;
if (!rw)
pp->cached_prdctl |= PRD_CTL_WR;
writeb(pp->cached_prdctl, port_base + PORT_PRD_CTL);
/* issue r/w command */
ap->ops->exec_command(ap, &qc->tf);
}
static void inic_bmdma_start(struct ata_queued_cmd *qc)
{
struct ata_port *ap = qc->ap;
struct inic_port_priv *pp = ap->private_data;
void __iomem *port_base = inic_port_base(ap);
/* start host DMA transaction */
pp->cached_prdctl |= PRD_CTL_START;
writeb(pp->cached_prdctl, port_base + PORT_PRD_CTL);
}
static void inic_bmdma_stop(struct ata_queued_cmd *qc)
{
struct ata_port *ap = qc->ap;
struct inic_port_priv *pp = ap->private_data;
void __iomem *port_base = inic_port_base(ap);
/* stop DMA engine */
writeb(pp->dfl_prdctl, port_base + PORT_PRD_CTL);
}
static u8 inic_bmdma_status(struct ata_port *ap)
{
/* event is already verified by the interrupt handler */
return ATA_DMA_INTR;
}
static void inic_irq_clear(struct ata_port *ap)
{
/* noop */
}
static void inic_host_intr(struct ata_port *ap)
{
void __iomem *port_base = inic_port_base(ap);
struct ata_eh_info *ehi = &ap->link.eh_info;
u8 irq_stat;
/* fetch and clear irq */
irq_stat = readb(port_base + PORT_IRQ_STAT);
writeb(irq_stat, port_base + PORT_IRQ_STAT);
if (likely(!(irq_stat & PIRQ_ERR))) {
struct ata_queued_cmd *qc =
ata_qc_from_tag(ap, ap->link.active_tag);
if (unlikely(!qc || (qc->tf.flags & ATA_TFLAG_POLLING))) {
ata_chk_status(ap); /* clear ATA interrupt */
return;
}
if (likely(ata_host_intr(ap, qc)))
return;
ata_chk_status(ap); /* clear ATA interrupt */
ata_port_printk(ap, KERN_WARNING, "unhandled "
"interrupt, irq_stat=%x\n", irq_stat);
return;
}
/* error */
ata_ehi_push_desc(ehi, "irq_stat=0x%x", irq_stat);
if (irq_stat & (PIRQ_OFFLINE | PIRQ_ONLINE)) {
ata_ehi_hotplugged(ehi);
ata_port_freeze(ap);
} else
ata_port_abort(ap);
}
static irqreturn_t inic_interrupt(int irq, void *dev_instance)
{
struct ata_host *host = dev_instance;
void __iomem *mmio_base = host->iomap[MMIO_BAR];
u16 host_irq_stat;
int i, handled = 0;;
host_irq_stat = readw(mmio_base + HOST_IRQ_STAT);
if (unlikely(!(host_irq_stat & HIRQ_GLOBAL)))
goto out;
spin_lock(&host->lock);
for (i = 0; i < NR_PORTS; i++) {
struct ata_port *ap = host->ports[i];
if (!(host_irq_stat & (HIRQ_PORT0 << i)))
continue;
if (likely(ap && !(ap->flags & ATA_FLAG_DISABLED))) {
inic_host_intr(ap);
handled++;
} else {
if (ata_ratelimit())
dev_printk(KERN_ERR, host->dev, "interrupt "
"from disabled port %d (0x%x)\n",
i, host_irq_stat);
}
}
spin_unlock(&host->lock);
out:
return IRQ_RETVAL(handled);
}
static unsigned int inic_qc_issue(struct ata_queued_cmd *qc)
{
struct ata_port *ap = qc->ap;
/* ATA IRQ doesn't wait for DMA transfer completion and vice
* versa. Mask IRQ selectively to detect command completion.
* Without it, ATA DMA read command can cause data corruption.
*
* Something similar might be needed for ATAPI writes. I
* tried a lot of combinations but couldn't find the solution.
*/
if (qc->tf.protocol == ATA_PROT_DMA &&
!(qc->tf.flags & ATA_TFLAG_WRITE))
inic_set_pirq_mask(ap, PIRQ_MASK_DMA_READ);
else
inic_set_pirq_mask(ap, PIRQ_MASK_OTHER);
/* Issuing a command to yet uninitialized port locks up the
* controller. Most of the time, this happens for the first
* command after reset which are ATA and ATAPI IDENTIFYs.
* Fast fail if stat is 0x7f or 0xff for those commands.
*/
if (unlikely(qc->tf.command == ATA_CMD_ID_ATA ||
qc->tf.command == ATA_CMD_ID_ATAPI)) {
u8 stat = ata_chk_status(ap);
if (stat == 0x7f || stat == 0xff)
return AC_ERR_HSM;
}
return ata_qc_issue_prot(qc);
}
static void inic_freeze(struct ata_port *ap)
{
void __iomem *port_base = inic_port_base(ap);
__inic_set_pirq_mask(ap, PIRQ_MASK_FREEZE);
ata_chk_status(ap);
writeb(0xff, port_base + PORT_IRQ_STAT);
readb(port_base + PORT_IRQ_STAT); /* flush */
}
static void inic_thaw(struct ata_port *ap)
{
void __iomem *port_base = inic_port_base(ap);
ata_chk_status(ap);
writeb(0xff, port_base + PORT_IRQ_STAT);
__inic_set_pirq_mask(ap, PIRQ_MASK_OTHER);
readb(port_base + PORT_IRQ_STAT); /* flush */
}
/*
* SRST and SControl hardreset don't give valid signature on this
* controller. Only controller specific hardreset mechanism works.
*/
static int inic_hardreset(struct ata_link *link, unsigned int *class,
unsigned long deadline)
{
struct ata_port *ap = link->ap;
void __iomem *port_base = inic_port_base(ap);
void __iomem *idma_ctl = port_base + PORT_IDMA_CTL;
const unsigned long *timing = sata_ehc_deb_timing(&link->eh_context);
u16 val;
int rc;
/* hammer it into sane state */
inic_reset_port(port_base);
val = readw(idma_ctl);
writew(val | IDMA_CTL_RST_ATA, idma_ctl);
readw(idma_ctl); /* flush */
msleep(1);
writew(val & ~IDMA_CTL_RST_ATA, idma_ctl);
rc = sata_link_resume(link, timing, deadline);
if (rc) {
ata_link_printk(link, KERN_WARNING, "failed to resume "
"link after reset (errno=%d)\n", rc);
return rc;
}
*class = ATA_DEV_NONE;
if (ata_link_online(link)) {
struct ata_taskfile tf;
/* wait a while before checking status */
ata_wait_after_reset(ap, deadline);
rc = ata_wait_ready(ap, deadline);
/* link occupied, -ENODEV too is an error */
if (rc) {
ata_link_printk(link, KERN_WARNING, "device not ready "
"after hardreset (errno=%d)\n", rc);
return rc;
}
ata_tf_read(ap, &tf);
*class = ata_dev_classify(&tf);
if (*class == ATA_DEV_UNKNOWN)
*class = ATA_DEV_NONE;
}
return 0;
}
static void inic_error_handler(struct ata_port *ap)
{
void __iomem *port_base = inic_port_base(ap);
struct inic_port_priv *pp = ap->private_data;
unsigned long flags;
/* reset PIO HSM and stop DMA engine */
inic_reset_port(port_base);
spin_lock_irqsave(ap->lock, flags);
ap->hsm_task_state = HSM_ST_IDLE;
writeb(pp->dfl_prdctl, port_base + PORT_PRD_CTL);
spin_unlock_irqrestore(ap->lock, flags);
/* PIO and DMA engines have been stopped, perform recovery */
ata_do_eh(ap, ata_std_prereset, NULL, inic_hardreset,
ata_std_postreset);
}
static void inic_post_internal_cmd(struct ata_queued_cmd *qc)
{
/* make DMA engine forget about the failed command */
if (qc->flags & ATA_QCFLAG_FAILED)
inic_reset_port(inic_port_base(qc->ap));
}
static void inic_dev_config(struct ata_device *dev)
{
/* inic can only handle upto LBA28 max sectors */
if (dev->max_sectors > ATA_MAX_SECTORS)
dev->max_sectors = ATA_MAX_SECTORS;
if (dev->n_sectors >= 1 << 28) {
ata_dev_printk(dev, KERN_ERR,
"ERROR: This driver doesn't support LBA48 yet and may cause\n"
" data corruption on such devices. Disabling.\n");
ata_dev_disable(dev);
}
}
static void init_port(struct ata_port *ap)
{
void __iomem *port_base = inic_port_base(ap);
/* Setup PRD address */
writel(ap->prd_dma, port_base + PORT_PRD_ADDR);
}
static int inic_port_resume(struct ata_port *ap)
{
init_port(ap);
return 0;
}
static int inic_port_start(struct ata_port *ap)
{
void __iomem *port_base = inic_port_base(ap);
struct inic_port_priv *pp;
u8 tmp;
int rc;
/* alloc and initialize private data */
pp = devm_kzalloc(ap->host->dev, sizeof(*pp), GFP_KERNEL);
if (!pp)
return -ENOMEM;
ap->private_data = pp;
/* default PRD_CTL value, DMAEN, WR and START off */
tmp = readb(port_base + PORT_PRD_CTL);
tmp &= ~(PRD_CTL_DMAEN | PRD_CTL_WR | PRD_CTL_START);
pp->dfl_prdctl = tmp;
/* Alloc resources */
rc = ata_port_start(ap);
if (rc) {
kfree(pp);
return rc;
}
init_port(ap);
return 0;
}
static struct ata_port_operations inic_port_ops = {
.tf_load = ata_tf_load,
.tf_read = ata_tf_read,
.check_status = ata_check_status,
.exec_command = ata_exec_command,
.dev_select = ata_std_dev_select,
.scr_read = inic_scr_read,
.scr_write = inic_scr_write,
.bmdma_setup = inic_bmdma_setup,
.bmdma_start = inic_bmdma_start,
.bmdma_stop = inic_bmdma_stop,
.bmdma_status = inic_bmdma_status,
.irq_clear = inic_irq_clear,
.irq_on = ata_irq_on,
.qc_prep = ata_qc_prep,
.qc_issue = inic_qc_issue,
.data_xfer = ata_data_xfer,
.freeze = inic_freeze,
.thaw = inic_thaw,
.error_handler = inic_error_handler,
.post_internal_cmd = inic_post_internal_cmd,
.dev_config = inic_dev_config,
.port_resume = inic_port_resume,
.port_start = inic_port_start,
};
static struct ata_port_info inic_port_info = {
/* For some reason, ATAPI_PROT_PIO is broken on this
* controller, and no, PIO_POLLING does't fix it. It somehow
* manages to report the wrong ireason and ignoring ireason
* results in machine lock up. Tell libata to always prefer
* DMA.
*/
.flags = ATA_FLAG_SATA | ATA_FLAG_PIO_DMA,
.pio_mask = 0x1f, /* pio0-4 */
.mwdma_mask = 0x07, /* mwdma0-2 */
.udma_mask = ATA_UDMA6,
.port_ops = &inic_port_ops
};
static int init_controller(void __iomem *mmio_base, u16 hctl)
{
int i;
u16 val;
hctl &= ~HCTL_KNOWN_BITS;
/* Soft reset whole controller. Spec says reset duration is 3
* PCI clocks, be generous and give it 10ms.
*/
writew(hctl | HCTL_SOFTRST, mmio_base + HOST_CTL);
readw(mmio_base + HOST_CTL); /* flush */
for (i = 0; i < 10; i++) {
msleep(1);
val = readw(mmio_base + HOST_CTL);
if (!(val & HCTL_SOFTRST))
break;
}
if (val & HCTL_SOFTRST)
return -EIO;
/* mask all interrupts and reset ports */
for (i = 0; i < NR_PORTS; i++) {
void __iomem *port_base = mmio_base + i * PORT_SIZE;
writeb(0xff, port_base + PORT_IRQ_MASK);
inic_reset_port(port_base);
}
/* port IRQ is masked now, unmask global IRQ */
writew(hctl & ~HCTL_IRQOFF, mmio_base + HOST_CTL);
val = readw(mmio_base + HOST_IRQ_MASK);
val &= ~(HIRQ_PORT0 | HIRQ_PORT1);
writew(val, mmio_base + HOST_IRQ_MASK);
return 0;
}
#ifdef CONFIG_PM
static int inic_pci_device_resume(struct pci_dev *pdev)
{
struct ata_host *host = dev_get_drvdata(&pdev->dev);
struct inic_host_priv *hpriv = host->private_data;
void __iomem *mmio_base = host->iomap[MMIO_BAR];
int rc;
rc = ata_pci_device_do_resume(pdev);
if (rc)
return rc;
if (pdev->dev.power.power_state.event == PM_EVENT_SUSPEND) {
rc = init_controller(mmio_base, hpriv->cached_hctl);
if (rc)
return rc;
}
ata_host_resume(host);
return 0;
}
#endif
static int inic_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
{
static int printed_version;
const struct ata_port_info *ppi[] = { &inic_port_info, NULL };
struct ata_host *host;
struct inic_host_priv *hpriv;
void __iomem * const *iomap;
int i, rc;
if (!printed_version++)
dev_printk(KERN_DEBUG, &pdev->dev, "version " DRV_VERSION "\n");
/* alloc host */
host = ata_host_alloc_pinfo(&pdev->dev, ppi, NR_PORTS);
hpriv = devm_kzalloc(&pdev->dev, sizeof(*hpriv), GFP_KERNEL);
if (!host || !hpriv)
return -ENOMEM;
host->private_data = hpriv;
/* acquire resources and fill host */
rc = pcim_enable_device(pdev);
if (rc)
return rc;
rc = pcim_iomap_regions(pdev, 0x3f, DRV_NAME);
if (rc)
return rc;
host->iomap = iomap = pcim_iomap_table(pdev);
for (i = 0; i < NR_PORTS; i++) {
struct ata_port *ap = host->ports[i];
struct ata_ioports *port = &ap->ioaddr;
unsigned int offset = i * PORT_SIZE;
port->cmd_addr = iomap[2 * i];
port->altstatus_addr =
port->ctl_addr = (void __iomem *)
((unsigned long)iomap[2 * i + 1] | ATA_PCI_CTL_OFS);
port->scr_addr = iomap[MMIO_BAR] + offset + PORT_SCR;
ata_std_ports(port);
ata_port_pbar_desc(ap, MMIO_BAR, -1, "mmio");
ata_port_pbar_desc(ap, MMIO_BAR, offset, "port");
ata_port_desc(ap, "cmd 0x%llx ctl 0x%llx",
(unsigned long long)pci_resource_start(pdev, 2 * i),
(unsigned long long)pci_resource_start(pdev, (2 * i + 1)) |
ATA_PCI_CTL_OFS);
}
hpriv->cached_hctl = readw(iomap[MMIO_BAR] + HOST_CTL);
/* Set dma_mask. This devices doesn't support 64bit addressing. */
rc = pci_set_dma_mask(pdev, DMA_32BIT_MASK);
if (rc) {
dev_printk(KERN_ERR, &pdev->dev,
"32-bit DMA enable failed\n");
return rc;
}
rc = pci_set_consistent_dma_mask(pdev, DMA_32BIT_MASK);
if (rc) {
dev_printk(KERN_ERR, &pdev->dev,
"32-bit consistent DMA enable failed\n");
return rc;
}
/*
* This controller is braindamaged. dma_boundary is 0xffff
* like others but it will lock up the whole machine HARD if
* 65536 byte PRD entry is fed. Reduce maximum segment size.
*/
rc = pci_set_dma_max_seg_size(pdev, 65536 - 512);
if (rc) {
dev_printk(KERN_ERR, &pdev->dev,
"failed to set the maximum segment size.\n");
return rc;
}
rc = init_controller(iomap[MMIO_BAR], hpriv->cached_hctl);
if (rc) {
dev_printk(KERN_ERR, &pdev->dev,
"failed to initialize controller\n");
return rc;
}
pci_set_master(pdev);
return ata_host_activate(host, pdev->irq, inic_interrupt, IRQF_SHARED,
&inic_sht);
}
static const struct pci_device_id inic_pci_tbl[] = {
{ PCI_VDEVICE(INIT, 0x1622), },
{ },
};
static struct pci_driver inic_pci_driver = {
.name = DRV_NAME,
.id_table = inic_pci_tbl,
#ifdef CONFIG_PM
.suspend = ata_pci_device_suspend,
.resume = inic_pci_device_resume,
#endif
.probe = inic_init_one,
.remove = ata_pci_remove_one,
};
static int __init inic_init(void)
{
return pci_register_driver(&inic_pci_driver);
}
static void __exit inic_exit(void)
{
pci_unregister_driver(&inic_pci_driver);
}
MODULE_AUTHOR("Tejun Heo");
MODULE_DESCRIPTION("low-level driver for Initio 162x SATA");
MODULE_LICENSE("GPL v2");
MODULE_DEVICE_TABLE(pci, inic_pci_tbl);
MODULE_VERSION(DRV_VERSION);
module_init(inic_init);
module_exit(inic_exit);