linux/arch/cris/arch-v32/mach-a3/Kconfig

115 lines
3.1 KiB
Plaintext

if CRIS_MACH_ARTPEC3
menu "Artpec-3 options"
depends on CRIS_MACH_ARTPEC3
config ETRAX_DRAM_VIRTUAL_BASE
hex
default "c0000000"
config ETRAX_L2CACHE
bool
default y
config ETRAX_SERIAL_PORTS
int
default 5
config ETRAX_DDR
bool
default y
config ETRAX_DDR2_MRS
hex "DDR2 MRS"
default "0"
config ETRAX_DDR2_TIMING
hex "DDR2 SDRAM timing"
default "0"
help
SDRAM timing parameters.
config ETRAX_DDR2_CONFIG
hex "DDR2 config"
default "0"
config ETRAX_DDR2_LATENCY
hex "DDR2 latency"
default "0"
config ETRAX_PIO_CE0_CFG
hex "PIO CE0 configuration"
default "0"
config ETRAX_PIO_CE1_CFG
hex "PIO CE1 configuration"
default "0"
config ETRAX_PIO_CE2_CFG
hex "PIO CE2 configuration"
default "0"
config ETRAX_DEF_GIO_PA_OE
hex "GIO_PA_OE"
default "00000000"
help
Configures the direction of general port A bits. 1 is out, 0 is in.
This is often totally different depending on the product used.
There are some guidelines though - if you know that only LED's are
connected to port PA, then they are usually connected to bits 2-4
and you can therefore use 1c. On other boards which don't have the
LED's at the general ports, these bits are used for all kinds of
stuff. If you don't know what to use, it is always safe to put all
as inputs, although floating inputs isn't good.
config ETRAX_DEF_GIO_PA_OUT
hex "GIO_PA_OUT"
default "00000000"
help
Configures the initial data for the general port A bits. Most
products should use 00 here.
config ETRAX_DEF_GIO_PB_OE
hex "GIO_PB_OE"
default "000000000"
help
Configures the direction of general port B bits. 1 is out, 0 is in.
This is often totally different depending on the product used.
There are some guidelines though - if you know that only LED's are
connected to port PA, then they are usually connected to bits 2-4
and you can therefore use 1c. On other boards which don't have the
LED's at the general ports, these bits are used for all kinds of
stuff. If you don't know what to use, it is always safe to put all
as inputs, although floating inputs isn't good.
config ETRAX_DEF_GIO_PB_OUT
hex "GIO_PB_OUT"
default "000000000"
help
Configures the initial data for the general port B bits. Most
products should use 00000 here.
config ETRAX_DEF_GIO_PC_OE
hex "GIO_PC_OE"
default "00000"
help
Configures the direction of general port C bits. 1 is out, 0 is in.
This is often totally different depending on the product used.
There are some guidelines though - if you know that only LED's are
connected to port PA, then they are usually connected to bits 2-4
and you can therefore use 1c. On other boards which don't have the
LED's at the general ports, these bits are used for all kinds of
stuff. If you don't know what to use, it is always safe to put all
as inputs, although floating inputs isn't good.
config ETRAX_DEF_GIO_PC_OUT
hex "GIO_PC_OUT"
default "00000"
help
Configures the initial data for the general port C bits. Most
products should use 00000 here.
endmenu
endif