ba5afadb11
This fixes the following: - CONFIG_ARC_SERIAL_BAUD is only defined when CONFIG_SERIAL_ARC is defined. Make sure that it isn't referenced otherwise. - There is no use for initializing arc_uart_info[] when CONFIG_SERIAL_ARC is not defined. [vgupta: tweaked changelog title, used IS_ENABLED() kconfig helper] Signed-off-by: Mischa Jonker <mjonker@synopsys.com> Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
245 lines
6.2 KiB
C
245 lines
6.2 KiB
C
/*
|
|
* ARC FPGA Platform support code
|
|
*
|
|
* Copyright (C) 2012 Synopsys, Inc. (www.synopsys.com)
|
|
*
|
|
* This program is free software; you can redistribute it and/or modify
|
|
* it under the terms of the GNU General Public License version 2 as
|
|
* published by the Free Software Foundation.
|
|
*/
|
|
|
|
#include <linux/types.h>
|
|
#include <linux/init.h>
|
|
#include <linux/device.h>
|
|
#include <linux/platform_device.h>
|
|
#include <linux/io.h>
|
|
#include <linux/console.h>
|
|
#include <linux/of_platform.h>
|
|
#include <asm/setup.h>
|
|
#include <asm/clk.h>
|
|
#include <asm/mach_desc.h>
|
|
#include <plat/memmap.h>
|
|
#include <plat/smp.h>
|
|
#include <plat/irq.h>
|
|
|
|
/*-----------------------BVCI Latency Unit -----------------------------*/
|
|
|
|
#ifdef CONFIG_ARC_HAS_BVCI_LAT_UNIT
|
|
|
|
int lat_cycles = CONFIG_BVCI_LAT_CYCLES;
|
|
|
|
/* BVCI Bus Profiler: Latency Unit */
|
|
static void __init setup_bvci_lat_unit(void)
|
|
{
|
|
#define MAX_BVCI_UNITS 12
|
|
|
|
unsigned int i;
|
|
unsigned int *base = (unsigned int *)BVCI_LAT_UNIT_BASE;
|
|
const unsigned long units_req = CONFIG_BVCI_LAT_UNITS;
|
|
const unsigned int REG_UNIT = 21;
|
|
const unsigned int REG_VAL = 22;
|
|
|
|
/*
|
|
* There are multiple Latency Units corresponding to the many
|
|
* interfaces of the system bus arbiter (both CPU side as well as
|
|
* the peripheral side).
|
|
*
|
|
* Unit 0 - System Arb and Mem Controller - adds latency to all
|
|
* memory trasactions
|
|
* Unit 1 - I$ and System Bus
|
|
* Unit 2 - D$ and System Bus
|
|
* ..
|
|
* Unit 12 - IDE Disk controller and System Bus
|
|
*
|
|
* The programmers model requires writing to lat_unit reg first
|
|
* and then the latency value (cycles) to lat_value reg
|
|
*/
|
|
|
|
if (CONFIG_BVCI_LAT_UNITS == 0) {
|
|
writel(0, base + REG_UNIT);
|
|
writel(lat_cycles, base + REG_VAL);
|
|
pr_info("BVCI Latency for all Memory Transactions %d cycles\n",
|
|
lat_cycles);
|
|
} else {
|
|
for_each_set_bit(i, &units_req, MAX_BVCI_UNITS) {
|
|
writel(i + 1, base + REG_UNIT); /* loop is 0 based */
|
|
writel(lat_cycles, base + REG_VAL);
|
|
pr_info("BVCI Latency for Unit[%d] = %d cycles\n",
|
|
(i + 1), lat_cycles);
|
|
}
|
|
}
|
|
}
|
|
#else
|
|
static void __init setup_bvci_lat_unit(void)
|
|
{
|
|
}
|
|
#endif
|
|
|
|
/*----------------------- Platform Devices -----------------------------*/
|
|
|
|
#if IS_ENABLED(CONFIG_SERIAL_ARC)
|
|
static unsigned long arc_uart_info[] = {
|
|
0, /* uart->is_emulated (runtime @running_on_hw) */
|
|
0, /* uart->port.uartclk */
|
|
0, /* uart->baud */
|
|
0
|
|
};
|
|
|
|
#if defined(CONFIG_SERIAL_ARC_CONSOLE)
|
|
/*
|
|
* static platform data - but only for early serial
|
|
* TBD: derive this from a special DT node
|
|
*/
|
|
static struct resource arc_uart0_res[] = {
|
|
{
|
|
.start = UART0_BASE,
|
|
.end = UART0_BASE + 0xFF,
|
|
.flags = IORESOURCE_MEM,
|
|
},
|
|
{
|
|
.start = UART0_IRQ,
|
|
.end = UART0_IRQ,
|
|
.flags = IORESOURCE_IRQ,
|
|
},
|
|
};
|
|
|
|
static struct platform_device arc_uart0_dev = {
|
|
.name = "arc-uart",
|
|
.id = 0,
|
|
.num_resources = ARRAY_SIZE(arc_uart0_res),
|
|
.resource = arc_uart0_res,
|
|
.dev = {
|
|
.platform_data = &arc_uart_info,
|
|
},
|
|
};
|
|
|
|
static struct platform_device *fpga_early_devs[] __initdata = {
|
|
&arc_uart0_dev,
|
|
};
|
|
#endif /* CONFIG_SERIAL_ARC_CONSOLE */
|
|
|
|
static void arc_fpga_serial_init(void)
|
|
{
|
|
/* To let driver workaround ISS bug: baudh Reg can't be set to 0 */
|
|
arc_uart_info[0] = !running_on_hw;
|
|
|
|
arc_uart_info[1] = arc_get_core_freq();
|
|
|
|
arc_uart_info[2] = CONFIG_ARC_SERIAL_BAUD;
|
|
|
|
#if defined(CONFIG_SERIAL_ARC_CONSOLE)
|
|
early_platform_add_devices(fpga_early_devs,
|
|
ARRAY_SIZE(fpga_early_devs));
|
|
|
|
/*
|
|
* ARC console driver registers itself as an early platform driver
|
|
* of class "earlyprintk".
|
|
* Install it here, followed by probe of devices.
|
|
* The installation here doesn't require earlyprintk in command line
|
|
* To do so however, replace the lines below with
|
|
* parse_early_param();
|
|
* early_platform_driver_probe("earlyprintk", 1, 1);
|
|
* ^^
|
|
*/
|
|
early_platform_driver_register_all("earlyprintk");
|
|
early_platform_driver_probe("earlyprintk", 1, 0);
|
|
|
|
/*
|
|
* This is to make sure that arc uart would be preferred console
|
|
* despite one/more of following:
|
|
* -command line lacked "console=ttyARC0" or
|
|
* -CONFIG_VT_CONSOLE was enabled (for no reason whatsoever)
|
|
* Note that this needs to be done after above early console is reg,
|
|
* otherwise the early console never gets a chance to run.
|
|
*/
|
|
add_preferred_console("ttyARC", 0, "115200");
|
|
#endif /* CONFIG_SERIAL_ARC_CONSOLE */
|
|
}
|
|
#else /* !IS_ENABLED(CONFIG_SERIAL_ARC) */
|
|
static void arc_fpga_serial_init(void)
|
|
{
|
|
}
|
|
#endif
|
|
|
|
static void __init plat_fpga_early_init(void)
|
|
{
|
|
pr_info("[plat-arcfpga]: registering early dev resources\n");
|
|
|
|
setup_bvci_lat_unit();
|
|
|
|
arc_fpga_serial_init();
|
|
|
|
#ifdef CONFIG_SMP
|
|
iss_model_init_early_smp();
|
|
#endif
|
|
}
|
|
|
|
static struct of_dev_auxdata plat_auxdata_lookup[] __initdata = {
|
|
#if IS_ENABLED(CONFIG_SERIAL_ARC)
|
|
OF_DEV_AUXDATA("snps,arc-uart", UART0_BASE, "arc-uart", arc_uart_info),
|
|
#endif
|
|
{}
|
|
};
|
|
|
|
static void __init plat_fpga_populate_dev(void)
|
|
{
|
|
pr_info("[plat-arcfpga]: registering device resources\n");
|
|
|
|
/*
|
|
* Traverses flattened DeviceTree - registering platform devices
|
|
* complete with their resources
|
|
*/
|
|
of_platform_populate(NULL, of_default_bus_match_table,
|
|
plat_auxdata_lookup, NULL);
|
|
}
|
|
|
|
/*----------------------- Machine Descriptions ------------------------------
|
|
*
|
|
* Machine description is simply a set of platform/board specific callbacks
|
|
* This is not directly related to DeviceTree based dynamic device creation,
|
|
* however as part of early device tree scan, we also select the right
|
|
* callback set, by matching the DT compatible name.
|
|
*/
|
|
|
|
static const char *aa4_compat[] __initdata = {
|
|
"snps,arc-angel4",
|
|
NULL,
|
|
};
|
|
|
|
MACHINE_START(ANGEL4, "angel4")
|
|
.dt_compat = aa4_compat,
|
|
.init_early = plat_fpga_early_init,
|
|
.init_machine = plat_fpga_populate_dev,
|
|
.init_irq = plat_fpga_init_IRQ,
|
|
#ifdef CONFIG_SMP
|
|
.init_smp = iss_model_init_smp,
|
|
#endif
|
|
MACHINE_END
|
|
|
|
static const char *ml509_compat[] __initdata = {
|
|
"snps,arc-ml509",
|
|
NULL,
|
|
};
|
|
|
|
MACHINE_START(ML509, "ml509")
|
|
.dt_compat = ml509_compat,
|
|
.init_early = plat_fpga_early_init,
|
|
.init_machine = plat_fpga_populate_dev,
|
|
.init_irq = plat_fpga_init_IRQ,
|
|
#ifdef CONFIG_SMP
|
|
.init_smp = iss_model_init_smp,
|
|
#endif
|
|
MACHINE_END
|
|
|
|
static const char *nsimosci_compat[] __initdata = {
|
|
"snps,nsimosci",
|
|
NULL,
|
|
};
|
|
|
|
MACHINE_START(NSIMOSCI, "nsimosci")
|
|
.dt_compat = nsimosci_compat,
|
|
.init_early = NULL,
|
|
.init_machine = plat_fpga_populate_dev,
|
|
.init_irq = NULL,
|
|
MACHINE_END
|