linux/arch/xtensa/Kconfig

250 lines
6.1 KiB
Plaintext

config FRAME_POINTER
def_bool n
config ZONE_DMA
def_bool y
config XTENSA
def_bool y
select HAVE_IDE
select HAVE_GENERIC_HARDIRQS
select GENERIC_IRQ_SHOW
help
Xtensa processors are 32-bit RISC machines designed by Tensilica
primarily for embedded systems. These processors are both
configurable and extensible. The Linux port to the Xtensa
architecture supports all processor configurations and extensions,
with reasonable minimum requirements. The Xtensa Linux project has
a home page at <http://xtensa.sourceforge.net/>.
config RWSEM_XCHGADD_ALGORITHM
def_bool y
config GENERIC_HWEIGHT
def_bool y
config GENERIC_GPIO
def_bool y
config ARCH_HAS_ILOG2_U32
def_bool n
config ARCH_HAS_ILOG2_U64
def_bool n
config NO_IOPORT
def_bool y
config HZ
int
default 100
source "init/Kconfig"
source "kernel/Kconfig.freezer"
config MMU
def_bool n
config VARIANT_IRQ_SWITCH
def_bool n
menu "Processor type and features"
choice
prompt "Xtensa Processor Configuration"
default XTENSA_VARIANT_FSF
config XTENSA_VARIANT_FSF
bool "fsf - default (not generic) configuration"
select MMU
config XTENSA_VARIANT_DC232B
bool "dc232b - Diamond 232L Standard Core Rev.B (LE)"
select MMU
help
This variant refers to Tensilica's Diamond 232L Standard core Rev.B (LE).
config XTENSA_VARIANT_S6000
bool "s6000 - Stretch software configurable processor"
select VARIANT_IRQ_SWITCH
select ARCH_REQUIRE_GPIOLIB
select XTENSA_CALIBRATE_CCOUNT
endchoice
config XTENSA_UNALIGNED_USER
bool "Unaligned memory access in use space"
help
The Xtensa architecture currently does not handle unaligned
memory accesses in hardware but through an exception handler.
Per default, unaligned memory accesses are disabled in user space.
Say Y here to enable unaligned memory access in user space.
source "kernel/Kconfig.preempt"
config MATH_EMULATION
bool "Math emulation"
help
Can we use information of configuration file?
endmenu
config XTENSA_CALIBRATE_CCOUNT
def_bool n
help
On some platforms (XT2000, for example), the CPU clock rate can
vary. The frequency can be determined, however, by measuring
against a well known, fixed frequency, such as an UART oscillator.
config SERIAL_CONSOLE
def_bool n
config XTENSA_ISS_NETWORK
def_bool n
menu "Bus options"
config PCI
bool "PCI support"
default y
help
Find out whether you have a PCI motherboard. PCI is the name of a
bus system, i.e. the way the CPU talks to the other stuff inside
your box. Other bus systems are ISA, EISA, MicroChannel (MCA) or
VESA. If you have PCI, say Y, otherwise N.
source "drivers/pci/Kconfig"
endmenu
menu "Platform options"
choice
prompt "Xtensa System Type"
default XTENSA_PLATFORM_ISS
config XTENSA_PLATFORM_ISS
bool "ISS"
select XTENSA_CALIBRATE_CCOUNT
select SERIAL_CONSOLE
select XTENSA_ISS_NETWORK
help
ISS is an acronym for Tensilica's Instruction Set Simulator.
config XTENSA_PLATFORM_XT2000
bool "XT2000"
help
XT2000 is the name of Tensilica's feature-rich emulation platform.
This hardware is capable of running a full Linux distribution.
config XTENSA_PLATFORM_S6105
bool "S6105"
select SERIAL_CONSOLE
endchoice
config XTENSA_CPU_CLOCK
int "CPU clock rate [MHz]"
depends on !XTENSA_CALIBRATE_CCOUNT
default 16
config GENERIC_CALIBRATE_DELAY
bool "Auto calibration of the BogoMIPS value"
help
The BogoMIPS value can easily be derived from the CPU frequency.
config CMDLINE_BOOL
bool "Default bootloader kernel arguments"
config CMDLINE
string "Initial kernel command string"
depends on CMDLINE_BOOL
default "console=ttyS0,38400 root=/dev/ram"
help
On some architectures (EBSA110 and CATS), there is currently no way
for the boot loader to pass arguments to the kernel. For these
architectures, you should supply some command-line options at build
time by entering them here. As a minimum, you should specify the
memory size and the root device (e.g., mem=64M root=/dev/nfs).
source "mm/Kconfig"
config HOTPLUG
bool "Support for hot-pluggable devices"
help
Say Y here if you want to plug devices into your computer while
the system is running, and be able to use them quickly. In many
cases, the devices can likewise be unplugged at any time too.
One well known example of this is PCMCIA- or PC-cards, credit-card
size devices such as network cards, modems or hard drives which are
plugged into slots found on all modern laptop computers. Another
example, used on modern desktops as well as laptops, is USB.
Enable HOTPLUG and build a modular kernel. Get agent software
(from <http://linux-hotplug.sourceforge.net/>) and install it.
Then your kernel will automatically call out to a user mode "policy
agent" (/sbin/hotplug) to load modules and set up software needed
to use devices as you hotplug them.
source "drivers/pcmcia/Kconfig"
source "drivers/pci/hotplug/Kconfig"
endmenu
menu "Executable file formats"
# only elf supported
config KCORE_ELF
def_bool y
depends on PROC_FS
help
If you enabled support for /proc file system then the file
/proc/kcore will contain the kernel core image in ELF format. This
can be used in gdb:
$ cd /usr/src/linux ; gdb vmlinux /proc/kcore
This is especially useful if you have compiled the kernel with the
"-g" option to preserve debugging information. It is mainly used
for examining kernel data structures on the live kernel.
source "fs/Kconfig.binfmt"
endmenu
source "net/Kconfig"
source "drivers/Kconfig"
source "fs/Kconfig"
menu "Xtensa initrd options"
depends on BLK_DEV_INITRD
config EMBEDDED_RAMDISK
bool "Embed root filesystem ramdisk into the kernel"
config EMBEDDED_RAMDISK_IMAGE
string "Filename of gzipped ramdisk image"
depends on EMBEDDED_RAMDISK
default "ramdisk.gz"
help
This is the filename of the ramdisk image to be built into the
kernel. Relative pathnames are relative to arch/xtensa/boot/ramdisk/.
The ramdisk image is not part of the kernel distribution; you must
provide one yourself.
endmenu
source "arch/xtensa/Kconfig.debug"
source "security/Kconfig"
source "crypto/Kconfig"
source "lib/Kconfig"