linux/arch/arm/mm/proc-v7.S
Jonathan Austin ddb2ff731b ARM: 7940/1: add support for the Cortex-A12 processor
The A12 behaves as the A7/A15 does with respect to setting the SMP bit, and
doesn't require TLB ops broadcasting to be explicitly enabled like the A9 does.

Note that as the ACTLR cannot (usually) be written from non-secure, it is the
responsibility of the bootloader/firmware to set this bit per core - it is
done here in Linux as last resort in case of bad firmware.

Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Jonathan Austin <jonathan.austin@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2014-02-10 11:48:00 +00:00

531 lines
15 KiB
ArmAsm

/*
* linux/arch/arm/mm/proc-v7.S
*
* Copyright (C) 2001 Deep Blue Solutions Ltd.
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*
* This is the "shell" of the ARMv7 processor support.
*/
#include <linux/init.h>
#include <linux/linkage.h>
#include <asm/assembler.h>
#include <asm/asm-offsets.h>
#include <asm/hwcap.h>
#include <asm/pgtable-hwdef.h>
#include <asm/pgtable.h>
#include "proc-macros.S"
#ifdef CONFIG_ARM_LPAE
#include "proc-v7-3level.S"
#else
#include "proc-v7-2level.S"
#endif
ENTRY(cpu_v7_proc_init)
mov pc, lr
ENDPROC(cpu_v7_proc_init)
ENTRY(cpu_v7_proc_fin)
mrc p15, 0, r0, c1, c0, 0 @ ctrl register
bic r0, r0, #0x1000 @ ...i............
bic r0, r0, #0x0006 @ .............ca.
mcr p15, 0, r0, c1, c0, 0 @ disable caches
mov pc, lr
ENDPROC(cpu_v7_proc_fin)
/*
* cpu_v7_reset(loc)
*
* Perform a soft reset of the system. Put the CPU into the
* same state as it would be if it had been reset, and branch
* to what would be the reset vector.
*
* - loc - location to jump to for soft reset
*
* This code must be executed using a flat identity mapping with
* caches disabled.
*/
.align 5
.pushsection .idmap.text, "ax"
ENTRY(cpu_v7_reset)
mrc p15, 0, r1, c1, c0, 0 @ ctrl register
bic r1, r1, #0x1 @ ...............m
THUMB( bic r1, r1, #1 << 30 ) @ SCTLR.TE (Thumb exceptions)
mcr p15, 0, r1, c1, c0, 0 @ disable MMU
isb
bx r0
ENDPROC(cpu_v7_reset)
.popsection
/*
* cpu_v7_do_idle()
*
* Idle the processor (eg, wait for interrupt).
*
* IRQs are already disabled.
*/
ENTRY(cpu_v7_do_idle)
dsb @ WFI may enter a low-power mode
wfi
mov pc, lr
ENDPROC(cpu_v7_do_idle)
ENTRY(cpu_v7_dcache_clean_area)
ALT_SMP(W(nop)) @ MP extensions imply L1 PTW
ALT_UP_B(1f)
mov pc, lr
1: dcache_line_size r2, r3
2: mcr p15, 0, r0, c7, c10, 1 @ clean D entry
add r0, r0, r2
subs r1, r1, r2
bhi 2b
dsb ishst
mov pc, lr
ENDPROC(cpu_v7_dcache_clean_area)
string cpu_v7_name, "ARMv7 Processor"
.align
/* Suspend/resume support: derived from arch/arm/mach-s5pv210/sleep.S */
.globl cpu_v7_suspend_size
.equ cpu_v7_suspend_size, 4 * 9
#ifdef CONFIG_ARM_CPU_SUSPEND
ENTRY(cpu_v7_do_suspend)
stmfd sp!, {r4 - r10, lr}
mrc p15, 0, r4, c13, c0, 0 @ FCSE/PID
mrc p15, 0, r5, c13, c0, 3 @ User r/o thread ID
stmia r0!, {r4 - r5}
#ifdef CONFIG_MMU
mrc p15, 0, r6, c3, c0, 0 @ Domain ID
#ifdef CONFIG_ARM_LPAE
mrrc p15, 1, r5, r7, c2 @ TTB 1
#else
mrc p15, 0, r7, c2, c0, 1 @ TTB 1
#endif
mrc p15, 0, r11, c2, c0, 2 @ TTB control register
#endif
mrc p15, 0, r8, c1, c0, 0 @ Control register
mrc p15, 0, r9, c1, c0, 1 @ Auxiliary control register
mrc p15, 0, r10, c1, c0, 2 @ Co-processor access control
stmia r0, {r5 - r11}
ldmfd sp!, {r4 - r10, pc}
ENDPROC(cpu_v7_do_suspend)
ENTRY(cpu_v7_do_resume)
mov ip, #0
mcr p15, 0, ip, c7, c5, 0 @ invalidate I cache
mcr p15, 0, ip, c13, c0, 1 @ set reserved context ID
ldmia r0!, {r4 - r5}
mcr p15, 0, r4, c13, c0, 0 @ FCSE/PID
mcr p15, 0, r5, c13, c0, 3 @ User r/o thread ID
ldmia r0, {r5 - r11}
#ifdef CONFIG_MMU
mcr p15, 0, ip, c8, c7, 0 @ invalidate TLBs
mcr p15, 0, r6, c3, c0, 0 @ Domain ID
#ifdef CONFIG_ARM_LPAE
mcrr p15, 0, r1, ip, c2 @ TTB 0
mcrr p15, 1, r5, r7, c2 @ TTB 1
#else
ALT_SMP(orr r1, r1, #TTB_FLAGS_SMP)
ALT_UP(orr r1, r1, #TTB_FLAGS_UP)
mcr p15, 0, r1, c2, c0, 0 @ TTB 0
mcr p15, 0, r7, c2, c0, 1 @ TTB 1
#endif
mcr p15, 0, r11, c2, c0, 2 @ TTB control register
ldr r4, =PRRR @ PRRR
ldr r5, =NMRR @ NMRR
mcr p15, 0, r4, c10, c2, 0 @ write PRRR
mcr p15, 0, r5, c10, c2, 1 @ write NMRR
#endif /* CONFIG_MMU */
mrc p15, 0, r4, c1, c0, 1 @ Read Auxiliary control register
teq r4, r9 @ Is it already set?
mcrne p15, 0, r9, c1, c0, 1 @ No, so write it
mcr p15, 0, r10, c1, c0, 2 @ Co-processor access control
isb
dsb
mov r0, r8 @ control register
b cpu_resume_mmu
ENDPROC(cpu_v7_do_resume)
#endif
#ifdef CONFIG_CPU_PJ4B
globl_equ cpu_pj4b_switch_mm, cpu_v7_switch_mm
globl_equ cpu_pj4b_set_pte_ext, cpu_v7_set_pte_ext
globl_equ cpu_pj4b_proc_init, cpu_v7_proc_init
globl_equ cpu_pj4b_proc_fin, cpu_v7_proc_fin
globl_equ cpu_pj4b_reset, cpu_v7_reset
#ifdef CONFIG_PJ4B_ERRATA_4742
ENTRY(cpu_pj4b_do_idle)
dsb @ WFI may enter a low-power mode
wfi
dsb @barrier
mov pc, lr
ENDPROC(cpu_pj4b_do_idle)
#else
globl_equ cpu_pj4b_do_idle, cpu_v7_do_idle
#endif
globl_equ cpu_pj4b_dcache_clean_area, cpu_v7_dcache_clean_area
globl_equ cpu_pj4b_do_suspend, cpu_v7_do_suspend
globl_equ cpu_pj4b_do_resume, cpu_v7_do_resume
globl_equ cpu_pj4b_suspend_size, cpu_v7_suspend_size
#endif
/*
* __v7_setup
*
* Initialise TLB, Caches, and MMU state ready to switch the MMU
* on. Return in r0 the new CP15 C1 control register setting.
*
* This should be able to cover all ARMv7 cores.
*
* It is assumed that:
* - cache type register is implemented
*/
__v7_ca5mp_setup:
__v7_ca9mp_setup:
__v7_cr7mp_setup:
mov r10, #(1 << 0) @ Cache/TLB ops broadcasting
b 1f
__v7_ca7mp_setup:
__v7_ca12mp_setup:
__v7_ca15mp_setup:
mov r10, #0
1:
#ifdef CONFIG_SMP
ALT_SMP(mrc p15, 0, r0, c1, c0, 1)
ALT_UP(mov r0, #(1 << 6)) @ fake it for UP
tst r0, #(1 << 6) @ SMP/nAMP mode enabled?
orreq r0, r0, #(1 << 6) @ Enable SMP/nAMP mode
orreq r0, r0, r10 @ Enable CPU-specific SMP bits
mcreq p15, 0, r0, c1, c0, 1
#endif
b __v7_setup
__v7_pj4b_setup:
#ifdef CONFIG_CPU_PJ4B
/* Auxiliary Debug Modes Control 1 Register */
#define PJ4B_STATIC_BP (1 << 2) /* Enable Static BP */
#define PJ4B_INTER_PARITY (1 << 8) /* Disable Internal Parity Handling */
#define PJ4B_BCK_OFF_STREX (1 << 5) /* Enable the back off of STREX instr */
#define PJ4B_CLEAN_LINE (1 << 16) /* Disable data transfer for clean line */
/* Auxiliary Debug Modes Control 2 Register */
#define PJ4B_FAST_LDR (1 << 23) /* Disable fast LDR */
#define PJ4B_SNOOP_DATA (1 << 25) /* Do not interleave write and snoop data */
#define PJ4B_CWF (1 << 27) /* Disable Critical Word First feature */
#define PJ4B_OUTSDNG_NC (1 << 29) /* Disable outstanding non cacheable rqst */
#define PJ4B_L1_REP_RR (1 << 30) /* L1 replacement - Strict round robin */
#define PJ4B_AUX_DBG_CTRL2 (PJ4B_SNOOP_DATA | PJ4B_CWF |\
PJ4B_OUTSDNG_NC | PJ4B_L1_REP_RR)
/* Auxiliary Functional Modes Control Register 0 */
#define PJ4B_SMP_CFB (1 << 1) /* Set SMP mode. Join the coherency fabric */
#define PJ4B_L1_PAR_CHK (1 << 2) /* Support L1 parity checking */
#define PJ4B_BROADCAST_CACHE (1 << 8) /* Broadcast Cache and TLB maintenance */
/* Auxiliary Debug Modes Control 0 Register */
#define PJ4B_WFI_WFE (1 << 22) /* WFI/WFE - serve the DVM and back to idle */
/* Auxiliary Debug Modes Control 1 Register */
mrc p15, 1, r0, c15, c1, 1
orr r0, r0, #PJ4B_CLEAN_LINE
orr r0, r0, #PJ4B_BCK_OFF_STREX
orr r0, r0, #PJ4B_INTER_PARITY
bic r0, r0, #PJ4B_STATIC_BP
mcr p15, 1, r0, c15, c1, 1
/* Auxiliary Debug Modes Control 2 Register */
mrc p15, 1, r0, c15, c1, 2
bic r0, r0, #PJ4B_FAST_LDR
orr r0, r0, #PJ4B_AUX_DBG_CTRL2
mcr p15, 1, r0, c15, c1, 2
/* Auxiliary Functional Modes Control Register 0 */
mrc p15, 1, r0, c15, c2, 0
#ifdef CONFIG_SMP
orr r0, r0, #PJ4B_SMP_CFB
#endif
orr r0, r0, #PJ4B_L1_PAR_CHK
orr r0, r0, #PJ4B_BROADCAST_CACHE
mcr p15, 1, r0, c15, c2, 0
/* Auxiliary Debug Modes Control 0 Register */
mrc p15, 1, r0, c15, c1, 0
orr r0, r0, #PJ4B_WFI_WFE
mcr p15, 1, r0, c15, c1, 0
#endif /* CONFIG_CPU_PJ4B */
__v7_setup:
adr r12, __v7_setup_stack @ the local stack
stmia r12, {r0-r5, r7, r9, r11, lr}
bl v7_flush_dcache_louis
ldmia r12, {r0-r5, r7, r9, r11, lr}
mrc p15, 0, r0, c0, c0, 0 @ read main ID register
and r10, r0, #0xff000000 @ ARM?
teq r10, #0x41000000
bne 3f
and r5, r0, #0x00f00000 @ variant
and r6, r0, #0x0000000f @ revision
orr r6, r6, r5, lsr #20-4 @ combine variant and revision
ubfx r0, r0, #4, #12 @ primary part number
/* Cortex-A8 Errata */
ldr r10, =0x00000c08 @ Cortex-A8 primary part number
teq r0, r10
bne 2f
#if defined(CONFIG_ARM_ERRATA_430973) && !defined(CONFIG_ARCH_MULTIPLATFORM)
teq r5, #0x00100000 @ only present in r1p*
mrceq p15, 0, r10, c1, c0, 1 @ read aux control register
orreq r10, r10, #(1 << 6) @ set IBE to 1
mcreq p15, 0, r10, c1, c0, 1 @ write aux control register
#endif
#ifdef CONFIG_ARM_ERRATA_458693
teq r6, #0x20 @ only present in r2p0
mrceq p15, 0, r10, c1, c0, 1 @ read aux control register
orreq r10, r10, #(1 << 5) @ set L1NEON to 1
orreq r10, r10, #(1 << 9) @ set PLDNOP to 1
mcreq p15, 0, r10, c1, c0, 1 @ write aux control register
#endif
#ifdef CONFIG_ARM_ERRATA_460075
teq r6, #0x20 @ only present in r2p0
mrceq p15, 1, r10, c9, c0, 2 @ read L2 cache aux ctrl register
tsteq r10, #1 << 22
orreq r10, r10, #(1 << 22) @ set the Write Allocate disable bit
mcreq p15, 1, r10, c9, c0, 2 @ write the L2 cache aux ctrl register
#endif
b 3f
/* Cortex-A9 Errata */
2: ldr r10, =0x00000c09 @ Cortex-A9 primary part number
teq r0, r10
bne 3f
#ifdef CONFIG_ARM_ERRATA_742230
cmp r6, #0x22 @ only present up to r2p2
mrcle p15, 0, r10, c15, c0, 1 @ read diagnostic register
orrle r10, r10, #1 << 4 @ set bit #4
mcrle p15, 0, r10, c15, c0, 1 @ write diagnostic register
#endif
#ifdef CONFIG_ARM_ERRATA_742231
teq r6, #0x20 @ present in r2p0
teqne r6, #0x21 @ present in r2p1
teqne r6, #0x22 @ present in r2p2
mrceq p15, 0, r10, c15, c0, 1 @ read diagnostic register
orreq r10, r10, #1 << 12 @ set bit #12
orreq r10, r10, #1 << 22 @ set bit #22
mcreq p15, 0, r10, c15, c0, 1 @ write diagnostic register
#endif
#ifdef CONFIG_ARM_ERRATA_743622
teq r5, #0x00200000 @ only present in r2p*
mrceq p15, 0, r10, c15, c0, 1 @ read diagnostic register
orreq r10, r10, #1 << 6 @ set bit #6
mcreq p15, 0, r10, c15, c0, 1 @ write diagnostic register
#endif
#if defined(CONFIG_ARM_ERRATA_751472) && defined(CONFIG_SMP)
ALT_SMP(cmp r6, #0x30) @ present prior to r3p0
ALT_UP_B(1f)
mrclt p15, 0, r10, c15, c0, 1 @ read diagnostic register
orrlt r10, r10, #1 << 11 @ set bit #11
mcrlt p15, 0, r10, c15, c0, 1 @ write diagnostic register
1:
#endif
/* Cortex-A15 Errata */
3: ldr r10, =0x00000c0f @ Cortex-A15 primary part number
teq r0, r10
bne 4f
#ifdef CONFIG_ARM_ERRATA_773022
cmp r6, #0x4 @ only present up to r0p4
mrcle p15, 0, r10, c1, c0, 1 @ read aux control register
orrle r10, r10, #1 << 1 @ disable loop buffer
mcrle p15, 0, r10, c1, c0, 1 @ write aux control register
#endif
4: mov r10, #0
mcr p15, 0, r10, c7, c5, 0 @ I+BTB cache invalidate
dsb
#ifdef CONFIG_MMU
mcr p15, 0, r10, c8, c7, 0 @ invalidate I + D TLBs
v7_ttb_setup r10, r4, r8, r5 @ TTBCR, TTBRx setup
ldr r5, =PRRR @ PRRR
ldr r6, =NMRR @ NMRR
mcr p15, 0, r5, c10, c2, 0 @ write PRRR
mcr p15, 0, r6, c10, c2, 1 @ write NMRR
#endif
#ifndef CONFIG_ARM_THUMBEE
mrc p15, 0, r0, c0, c1, 0 @ read ID_PFR0 for ThumbEE
and r0, r0, #(0xf << 12) @ ThumbEE enabled field
teq r0, #(1 << 12) @ check if ThumbEE is present
bne 1f
mov r5, #0
mcr p14, 6, r5, c1, c0, 0 @ Initialize TEEHBR to 0
mrc p14, 6, r0, c0, c0, 0 @ load TEECR
orr r0, r0, #1 @ set the 1st bit in order to
mcr p14, 6, r0, c0, c0, 0 @ stop userspace TEEHBR access
1:
#endif
adr r5, v7_crval
ldmia r5, {r5, r6}
ARM_BE8(orr r6, r6, #1 << 25) @ big-endian page tables
#ifdef CONFIG_SWP_EMULATE
orr r5, r5, #(1 << 10) @ set SW bit in "clear"
bic r6, r6, #(1 << 10) @ clear it in "mmuset"
#endif
mrc p15, 0, r0, c1, c0, 0 @ read control register
bic r0, r0, r5 @ clear bits them
orr r0, r0, r6 @ set them
THUMB( orr r0, r0, #1 << 30 ) @ Thumb exceptions
mov pc, lr @ return to head.S:__ret
ENDPROC(__v7_setup)
.align 2
__v7_setup_stack:
.space 4 * 11 @ 11 registers
__INITDATA
@ define struct processor (see <asm/proc-fns.h> and proc-macros.S)
define_processor_functions v7, dabort=v7_early_abort, pabort=v7_pabort, suspend=1
#ifdef CONFIG_CPU_PJ4B
define_processor_functions pj4b, dabort=v7_early_abort, pabort=v7_pabort, suspend=1
#endif
.section ".rodata"
string cpu_arch_name, "armv7"
string cpu_elf_name, "v7"
.align
.section ".proc.info.init", #alloc, #execinstr
/*
* Standard v7 proc info content
*/
.macro __v7_proc initfunc, mm_mmuflags = 0, io_mmuflags = 0, hwcaps = 0, proc_fns = v7_processor_functions
ALT_SMP(.long PMD_TYPE_SECT | PMD_SECT_AP_WRITE | PMD_SECT_AP_READ | \
PMD_SECT_AF | PMD_FLAGS_SMP | \mm_mmuflags)
ALT_UP(.long PMD_TYPE_SECT | PMD_SECT_AP_WRITE | PMD_SECT_AP_READ | \
PMD_SECT_AF | PMD_FLAGS_UP | \mm_mmuflags)
.long PMD_TYPE_SECT | PMD_SECT_AP_WRITE | \
PMD_SECT_AP_READ | PMD_SECT_AF | \io_mmuflags
W(b) \initfunc
.long cpu_arch_name
.long cpu_elf_name
.long HWCAP_SWP | HWCAP_HALF | HWCAP_THUMB | HWCAP_FAST_MULT | \
HWCAP_EDSP | HWCAP_TLS | \hwcaps
.long cpu_v7_name
.long \proc_fns
.long v7wbi_tlb_fns
.long v6_user_fns
.long v7_cache_fns
.endm
#ifndef CONFIG_ARM_LPAE
/*
* ARM Ltd. Cortex A5 processor.
*/
.type __v7_ca5mp_proc_info, #object
__v7_ca5mp_proc_info:
.long 0x410fc050
.long 0xff0ffff0
__v7_proc __v7_ca5mp_setup
.size __v7_ca5mp_proc_info, . - __v7_ca5mp_proc_info
/*
* ARM Ltd. Cortex A9 processor.
*/
.type __v7_ca9mp_proc_info, #object
__v7_ca9mp_proc_info:
.long 0x410fc090
.long 0xff0ffff0
__v7_proc __v7_ca9mp_setup
.size __v7_ca9mp_proc_info, . - __v7_ca9mp_proc_info
#endif /* CONFIG_ARM_LPAE */
/*
* Marvell PJ4B processor.
*/
#ifdef CONFIG_CPU_PJ4B
.type __v7_pj4b_proc_info, #object
__v7_pj4b_proc_info:
.long 0x560f5800
.long 0xff0fff00
__v7_proc __v7_pj4b_setup, proc_fns = pj4b_processor_functions
.size __v7_pj4b_proc_info, . - __v7_pj4b_proc_info
#endif
/*
* ARM Ltd. Cortex R7 processor.
*/
.type __v7_cr7mp_proc_info, #object
__v7_cr7mp_proc_info:
.long 0x410fc170
.long 0xff0ffff0
__v7_proc __v7_cr7mp_setup
.size __v7_cr7mp_proc_info, . - __v7_cr7mp_proc_info
/*
* ARM Ltd. Cortex A7 processor.
*/
.type __v7_ca7mp_proc_info, #object
__v7_ca7mp_proc_info:
.long 0x410fc070
.long 0xff0ffff0
__v7_proc __v7_ca7mp_setup
.size __v7_ca7mp_proc_info, . - __v7_ca7mp_proc_info
/*
* ARM Ltd. Cortex A12 processor.
*/
.type __v7_ca12mp_proc_info, #object
__v7_ca12mp_proc_info:
.long 0x410fc0d0
.long 0xff0ffff0
__v7_proc __v7_ca12mp_setup
.size __v7_ca12mp_proc_info, . - __v7_ca12mp_proc_info
/*
* ARM Ltd. Cortex A15 processor.
*/
.type __v7_ca15mp_proc_info, #object
__v7_ca15mp_proc_info:
.long 0x410fc0f0
.long 0xff0ffff0
__v7_proc __v7_ca15mp_setup
.size __v7_ca15mp_proc_info, . - __v7_ca15mp_proc_info
/*
* Qualcomm Inc. Krait processors.
*/
.type __krait_proc_info, #object
__krait_proc_info:
.long 0x510f0400 @ Required ID value
.long 0xff0ffc00 @ Mask for ID
/*
* Some Krait processors don't indicate support for SDIV and UDIV
* instructions in the ARM instruction set, even though they actually
* do support them.
*/
__v7_proc __v7_setup, hwcaps = HWCAP_IDIV
.size __krait_proc_info, . - __krait_proc_info
/*
* Match any ARMv7 processor core.
*/
.type __v7_proc_info, #object
__v7_proc_info:
.long 0x000f0000 @ Required ID value
.long 0x000f0000 @ Mask for ID
__v7_proc __v7_setup
.size __v7_proc_info, . - __v7_proc_info