225 lines
6.1 KiB
Plaintext
225 lines
6.1 KiB
Plaintext
CPU frequency and voltage scaling code in the Linux(TM) kernel
|
|
|
|
|
|
L i n u x C P U F r e q
|
|
|
|
U S E R G U I D E
|
|
|
|
|
|
Dominik Brodowski <linux@brodo.de>
|
|
|
|
|
|
|
|
Clock scaling allows you to change the clock speed of the CPUs on the
|
|
fly. This is a nice method to save battery power, because the lower
|
|
the clock speed, the less power the CPU consumes.
|
|
|
|
|
|
Contents:
|
|
---------
|
|
1. Supported Architectures and Processors
|
|
1.1 ARM
|
|
1.2 x86
|
|
1.3 sparc64
|
|
1.4 ppc
|
|
1.5 SuperH
|
|
1.6 Blackfin
|
|
|
|
2. "Policy" / "Governor"?
|
|
2.1 Policy
|
|
2.2 Governor
|
|
|
|
3. How to change the CPU cpufreq policy and/or speed
|
|
3.1 Preferred interface: sysfs
|
|
|
|
|
|
|
|
1. Supported Architectures and Processors
|
|
=========================================
|
|
|
|
1.1 ARM
|
|
-------
|
|
|
|
The following ARM processors are supported by cpufreq:
|
|
|
|
ARM Integrator
|
|
ARM-SA1100
|
|
ARM-SA1110
|
|
Intel PXA
|
|
|
|
|
|
1.2 x86
|
|
-------
|
|
|
|
The following processors for the x86 architecture are supported by cpufreq:
|
|
|
|
AMD Elan - SC400, SC410
|
|
AMD mobile K6-2+
|
|
AMD mobile K6-3+
|
|
AMD mobile Duron
|
|
AMD mobile Athlon
|
|
AMD Opteron
|
|
AMD Athlon 64
|
|
Cyrix Media GXm
|
|
Intel mobile PIII and Intel mobile PIII-M on certain chipsets
|
|
Intel Pentium 4, Intel Xeon
|
|
Intel Pentium M (Centrino)
|
|
National Semiconductors Geode GX
|
|
Transmeta Crusoe
|
|
Transmeta Efficeon
|
|
VIA Cyrix 3 / C3
|
|
various processors on some ACPI 2.0-compatible systems [*]
|
|
|
|
[*] Only if "ACPI Processor Performance States" are available
|
|
to the ACPI<->BIOS interface.
|
|
|
|
|
|
1.3 sparc64
|
|
-----------
|
|
|
|
The following processors for the sparc64 architecture are supported by
|
|
cpufreq:
|
|
|
|
UltraSPARC-III
|
|
|
|
|
|
1.4 ppc
|
|
-------
|
|
|
|
Several "PowerBook" and "iBook2" notebooks are supported.
|
|
|
|
|
|
1.5 SuperH
|
|
----------
|
|
|
|
All SuperH processors supporting rate rounding through the clock
|
|
framework are supported by cpufreq.
|
|
|
|
1.6 Blackfin
|
|
------------
|
|
|
|
The following Blackfin processors are supported by cpufreq:
|
|
|
|
BF522, BF523, BF524, BF525, BF526, BF527, Rev 0.1 or higher
|
|
BF531, BF532, BF533, Rev 0.3 or higher
|
|
BF534, BF536, BF537, Rev 0.2 or higher
|
|
BF561, Rev 0.3 or higher
|
|
BF542, BF544, BF547, BF548, BF549, Rev 0.1 or higher
|
|
|
|
|
|
2. "Policy" / "Governor" ?
|
|
==========================
|
|
|
|
Some CPU frequency scaling-capable processor switch between various
|
|
frequencies and operating voltages "on the fly" without any kernel or
|
|
user involvement. This guarantees very fast switching to a frequency
|
|
which is high enough to serve the user's needs, but low enough to save
|
|
power.
|
|
|
|
|
|
2.1 Policy
|
|
----------
|
|
|
|
On these systems, all you can do is select the lower and upper
|
|
frequency limit as well as whether you want more aggressive
|
|
power-saving or more instantly available processing power.
|
|
|
|
|
|
2.2 Governor
|
|
------------
|
|
|
|
On all other cpufreq implementations, these boundaries still need to
|
|
be set. Then, a "governor" must be selected. Such a "governor" decides
|
|
what speed the processor shall run within the boundaries. One such
|
|
"governor" is the "userspace" governor. This one allows the user - or
|
|
a yet-to-implement userspace program - to decide what specific speed
|
|
the processor shall run at.
|
|
|
|
|
|
3. How to change the CPU cpufreq policy and/or speed
|
|
====================================================
|
|
|
|
3.1 Preferred Interface: sysfs
|
|
------------------------------
|
|
|
|
The preferred interface is located in the sysfs filesystem. If you
|
|
mounted it at /sys, the cpufreq interface is located in a subdirectory
|
|
"cpufreq" within the cpu-device directory
|
|
(e.g. /sys/devices/system/cpu/cpu0/cpufreq/ for the first CPU).
|
|
|
|
cpuinfo_min_freq : this file shows the minimum operating
|
|
frequency the processor can run at(in kHz)
|
|
cpuinfo_max_freq : this file shows the maximum operating
|
|
frequency the processor can run at(in kHz)
|
|
cpuinfo_transition_latency The time it takes on this CPU to
|
|
switch between two frequencies in nano
|
|
seconds. If unknown or known to be
|
|
that high that the driver does not
|
|
work with the ondemand governor, -1
|
|
(CPUFREQ_ETERNAL) will be returned.
|
|
Using this information can be useful
|
|
to choose an appropriate polling
|
|
frequency for a kernel governor or
|
|
userspace daemon. Make sure to not
|
|
switch the frequency too often
|
|
resulting in performance loss.
|
|
scaling_driver : this file shows what cpufreq driver is
|
|
used to set the frequency on this CPU
|
|
|
|
scaling_available_governors : this file shows the CPUfreq governors
|
|
available in this kernel. You can see the
|
|
currently activated governor in
|
|
|
|
scaling_governor, and by "echoing" the name of another
|
|
governor you can change it. Please note
|
|
that some governors won't load - they only
|
|
work on some specific architectures or
|
|
processors.
|
|
|
|
cpuinfo_cur_freq : Current frequency of the CPU as obtained from
|
|
the hardware, in KHz. This is the frequency
|
|
the CPU actually runs at.
|
|
|
|
scaling_available_frequencies : List of available frequencies, in KHz.
|
|
|
|
scaling_min_freq and
|
|
scaling_max_freq show the current "policy limits" (in
|
|
kHz). By echoing new values into these
|
|
files, you can change these limits.
|
|
NOTE: when setting a policy you need to
|
|
first set scaling_max_freq, then
|
|
scaling_min_freq.
|
|
|
|
affected_cpus : List of CPUs that require software coordination
|
|
of frequency.
|
|
|
|
related_cpus : List of CPUs that need some sort of frequency
|
|
coordination, whether software or hardware.
|
|
|
|
scaling_driver : Hardware driver for cpufreq.
|
|
|
|
scaling_cur_freq : Current frequency of the CPU as determined by
|
|
the governor and cpufreq core, in KHz. This is
|
|
the frequency the kernel thinks the CPU runs
|
|
at.
|
|
|
|
bios_limit : If the BIOS tells the OS to limit a CPU to
|
|
lower frequencies, the user can read out the
|
|
maximum available frequency from this file.
|
|
This typically can happen through (often not
|
|
intended) BIOS settings, restrictions
|
|
triggered through a service processor or other
|
|
BIOS/HW based implementations.
|
|
This does not cover thermal ACPI limitations
|
|
which can be detected through the generic
|
|
thermal driver.
|
|
|
|
If you have selected the "userspace" governor which allows you to
|
|
set the CPU operating frequency to a specific value, you can read out
|
|
the current frequency in
|
|
|
|
scaling_setspeed. By "echoing" a new frequency into this
|
|
you can change the speed of the CPU,
|
|
but only within the limits of
|
|
scaling_min_freq and scaling_max_freq.
|