a1a38c4c6a
Access to the SEC4 DECOs (DEscriptor COntrollers) (for debug purposes) isn't supported or used, and its register access initialization code erroneously makes illegal i/o accesses that show up as errors when run under simulation. Remove it until proper support (via DECORR) is added. Signed-off-by: Kim Phillips <kim.phillips@freescale.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
663 lines
21 KiB
C
663 lines
21 KiB
C
/*
|
|
* CAAM hardware register-level view
|
|
*
|
|
* Copyright 2008-2011 Freescale Semiconductor, Inc.
|
|
*/
|
|
|
|
#ifndef REGS_H
|
|
#define REGS_H
|
|
|
|
#include <linux/types.h>
|
|
#include <linux/io.h>
|
|
|
|
/*
|
|
* Architecture-specific register access methods
|
|
*
|
|
* CAAM's bus-addressable registers are 64 bits internally.
|
|
* They have been wired to be safely accessible on 32-bit
|
|
* architectures, however. Registers were organized such
|
|
* that (a) they can be contained in 32 bits, (b) if not, then they
|
|
* can be treated as two 32-bit entities, or finally (c) if they
|
|
* must be treated as a single 64-bit value, then this can safely
|
|
* be done with two 32-bit cycles.
|
|
*
|
|
* For 32-bit operations on 64-bit values, CAAM follows the same
|
|
* 64-bit register access conventions as it's predecessors, in that
|
|
* writes are "triggered" by a write to the register at the numerically
|
|
* higher address, thus, a full 64-bit write cycle requires a write
|
|
* to the lower address, followed by a write to the higher address,
|
|
* which will latch/execute the write cycle.
|
|
*
|
|
* For example, let's assume a SW reset of CAAM through the master
|
|
* configuration register.
|
|
* - SWRST is in bit 31 of MCFG.
|
|
* - MCFG begins at base+0x0000.
|
|
* - Bits 63-32 are a 32-bit word at base+0x0000 (numerically-lower)
|
|
* - Bits 31-0 are a 32-bit word at base+0x0004 (numerically-higher)
|
|
*
|
|
* (and on Power, the convention is 0-31, 32-63, I know...)
|
|
*
|
|
* Assuming a 64-bit write to this MCFG to perform a software reset
|
|
* would then require a write of 0 to base+0x0000, followed by a
|
|
* write of 0x80000000 to base+0x0004, which would "execute" the
|
|
* reset.
|
|
*
|
|
* Of course, since MCFG 63-32 is all zero, we could cheat and simply
|
|
* write 0x8000000 to base+0x0004, and the reset would work fine.
|
|
* However, since CAAM does contain some write-and-read-intended
|
|
* 64-bit registers, this code defines 64-bit access methods for
|
|
* the sake of internal consistency and simplicity, and so that a
|
|
* clean transition to 64-bit is possible when it becomes necessary.
|
|
*
|
|
* There are limitations to this that the developer must recognize.
|
|
* 32-bit architectures cannot enforce an atomic-64 operation,
|
|
* Therefore:
|
|
*
|
|
* - On writes, since the HW is assumed to latch the cycle on the
|
|
* write of the higher-numeric-address word, then ordered
|
|
* writes work OK.
|
|
*
|
|
* - For reads, where a register contains a relevant value of more
|
|
* that 32 bits, the hardware employs logic to latch the other
|
|
* "half" of the data until read, ensuring an accurate value.
|
|
* This is of particular relevance when dealing with CAAM's
|
|
* performance counters.
|
|
*
|
|
*/
|
|
|
|
#ifdef __BIG_ENDIAN
|
|
#define wr_reg32(reg, data) out_be32(reg, data)
|
|
#define rd_reg32(reg) in_be32(reg)
|
|
#ifdef CONFIG_64BIT
|
|
#define wr_reg64(reg, data) out_be64(reg, data)
|
|
#define rd_reg64(reg) in_be64(reg)
|
|
#endif
|
|
#else
|
|
#ifdef __LITTLE_ENDIAN
|
|
#define wr_reg32(reg, data) __raw_writel(reg, data)
|
|
#define rd_reg32(reg) __raw_readl(reg)
|
|
#ifdef CONFIG_64BIT
|
|
#define wr_reg64(reg, data) __raw_writeq(reg, data)
|
|
#define rd_reg64(reg) __raw_readq(reg)
|
|
#endif
|
|
#endif
|
|
#endif
|
|
|
|
#ifndef CONFIG_64BIT
|
|
static inline void wr_reg64(u64 __iomem *reg, u64 data)
|
|
{
|
|
wr_reg32((u32 __iomem *)reg, (data & 0xffffffff00000000ull) >> 32);
|
|
wr_reg32((u32 __iomem *)reg + 1, data & 0x00000000ffffffffull);
|
|
}
|
|
|
|
static inline u64 rd_reg64(u64 __iomem *reg)
|
|
{
|
|
return (((u64)rd_reg32((u32 __iomem *)reg)) << 32) |
|
|
((u64)rd_reg32((u32 __iomem *)reg + 1));
|
|
}
|
|
#endif
|
|
|
|
/*
|
|
* jr_outentry
|
|
* Represents each entry in a JobR output ring
|
|
*/
|
|
struct jr_outentry {
|
|
dma_addr_t desc;/* Pointer to completed descriptor */
|
|
u32 jrstatus; /* Status for completed descriptor */
|
|
} __packed;
|
|
|
|
/*
|
|
* caam_perfmon - Performance Monitor/Secure Memory Status/
|
|
* CAAM Global Status/Component Version IDs
|
|
*
|
|
* Spans f00-fff wherever instantiated
|
|
*/
|
|
|
|
/* Number of DECOs */
|
|
#define CHA_NUM_DECONUM_SHIFT 56
|
|
#define CHA_NUM_DECONUM_MASK (0xfull << CHA_NUM_DECONUM_SHIFT)
|
|
|
|
struct caam_perfmon {
|
|
/* Performance Monitor Registers f00-f9f */
|
|
u64 req_dequeued; /* PC_REQ_DEQ - Dequeued Requests */
|
|
u64 ob_enc_req; /* PC_OB_ENC_REQ - Outbound Encrypt Requests */
|
|
u64 ib_dec_req; /* PC_IB_DEC_REQ - Inbound Decrypt Requests */
|
|
u64 ob_enc_bytes; /* PC_OB_ENCRYPT - Outbound Bytes Encrypted */
|
|
u64 ob_prot_bytes; /* PC_OB_PROTECT - Outbound Bytes Protected */
|
|
u64 ib_dec_bytes; /* PC_IB_DECRYPT - Inbound Bytes Decrypted */
|
|
u64 ib_valid_bytes; /* PC_IB_VALIDATED Inbound Bytes Validated */
|
|
u64 rsvd[13];
|
|
|
|
/* CAAM Hardware Instantiation Parameters fa0-fbf */
|
|
u64 cha_rev; /* CRNR - CHA Revision Number */
|
|
#define CTPR_QI_SHIFT 57
|
|
#define CTPR_QI_MASK (0x1ull << CTPR_QI_SHIFT)
|
|
u64 comp_parms; /* CTPR - Compile Parameters Register */
|
|
u64 rsvd1[2];
|
|
|
|
/* CAAM Global Status fc0-fdf */
|
|
u64 faultaddr; /* FAR - Fault Address */
|
|
u32 faultliodn; /* FALR - Fault Address LIODN */
|
|
u32 faultdetail; /* FADR - Fault Addr Detail */
|
|
u32 rsvd2;
|
|
u32 status; /* CSTA - CAAM Status */
|
|
u64 rsvd3;
|
|
|
|
/* Component Instantiation Parameters fe0-fff */
|
|
u32 rtic_id; /* RVID - RTIC Version ID */
|
|
u32 ccb_id; /* CCBVID - CCB Version ID */
|
|
u64 cha_id; /* CHAVID - CHA Version ID */
|
|
u64 cha_num; /* CHANUM - CHA Number */
|
|
u64 caam_id; /* CAAMVID - CAAM Version ID */
|
|
};
|
|
|
|
/* LIODN programming for DMA configuration */
|
|
#define MSTRID_LOCK_LIODN 0x80000000
|
|
#define MSTRID_LOCK_MAKETRUSTED 0x00010000 /* only for JR masterid */
|
|
|
|
#define MSTRID_LIODN_MASK 0x0fff
|
|
struct masterid {
|
|
u32 liodn_ms; /* lock and make-trusted control bits */
|
|
u32 liodn_ls; /* LIODN for non-sequence and seq access */
|
|
};
|
|
|
|
/* Partition ID for DMA configuration */
|
|
struct partid {
|
|
u32 rsvd1;
|
|
u32 pidr; /* partition ID, DECO */
|
|
};
|
|
|
|
/* RNG test mode (replicated twice in some configurations) */
|
|
/* Padded out to 0x100 */
|
|
struct rngtst {
|
|
u32 mode; /* RTSTMODEx - Test mode */
|
|
u32 rsvd1[3];
|
|
u32 reset; /* RTSTRESETx - Test reset control */
|
|
u32 rsvd2[3];
|
|
u32 status; /* RTSTSSTATUSx - Test status */
|
|
u32 rsvd3;
|
|
u32 errstat; /* RTSTERRSTATx - Test error status */
|
|
u32 rsvd4;
|
|
u32 errctl; /* RTSTERRCTLx - Test error control */
|
|
u32 rsvd5;
|
|
u32 entropy; /* RTSTENTROPYx - Test entropy */
|
|
u32 rsvd6[15];
|
|
u32 verifctl; /* RTSTVERIFCTLx - Test verification control */
|
|
u32 rsvd7;
|
|
u32 verifstat; /* RTSTVERIFSTATx - Test verification status */
|
|
u32 rsvd8;
|
|
u32 verifdata; /* RTSTVERIFDx - Test verification data */
|
|
u32 rsvd9;
|
|
u32 xkey; /* RTSTXKEYx - Test XKEY */
|
|
u32 rsvd10;
|
|
u32 oscctctl; /* RTSTOSCCTCTLx - Test osc. counter control */
|
|
u32 rsvd11;
|
|
u32 oscct; /* RTSTOSCCTx - Test oscillator counter */
|
|
u32 rsvd12;
|
|
u32 oscctstat; /* RTSTODCCTSTATx - Test osc counter status */
|
|
u32 rsvd13[2];
|
|
u32 ofifo[4]; /* RTSTOFIFOx - Test output FIFO */
|
|
u32 rsvd14[15];
|
|
};
|
|
|
|
/*
|
|
* caam_ctrl - basic core configuration
|
|
* starts base + 0x0000 padded out to 0x1000
|
|
*/
|
|
|
|
#define KEK_KEY_SIZE 8
|
|
#define TKEK_KEY_SIZE 8
|
|
#define TDSK_KEY_SIZE 8
|
|
|
|
#define DECO_RESET 1 /* Use with DECO reset/availability regs */
|
|
#define DECO_RESET_0 (DECO_RESET << 0)
|
|
#define DECO_RESET_1 (DECO_RESET << 1)
|
|
#define DECO_RESET_2 (DECO_RESET << 2)
|
|
#define DECO_RESET_3 (DECO_RESET << 3)
|
|
#define DECO_RESET_4 (DECO_RESET << 4)
|
|
|
|
struct caam_ctrl {
|
|
/* Basic Configuration Section 000-01f */
|
|
/* Read/Writable */
|
|
u32 rsvd1;
|
|
u32 mcr; /* MCFG Master Config Register */
|
|
u32 rsvd2[2];
|
|
|
|
/* Bus Access Configuration Section 010-11f */
|
|
/* Read/Writable */
|
|
struct masterid jr_mid[4]; /* JRxLIODNR - JobR LIODN setup */
|
|
u32 rsvd3[12];
|
|
struct masterid rtic_mid[4]; /* RTICxLIODNR - RTIC LIODN setup */
|
|
u32 rsvd4[7];
|
|
u32 deco_rq; /* DECORR - DECO Request */
|
|
struct partid deco_mid[5]; /* DECOxLIODNR - 1 per DECO */
|
|
u32 rsvd5[22];
|
|
|
|
/* DECO Availability/Reset Section 120-3ff */
|
|
u32 deco_avail; /* DAR - DECO availability */
|
|
u32 deco_reset; /* DRR - DECO reset */
|
|
u32 rsvd6[182];
|
|
|
|
/* Key Encryption/Decryption Configuration 400-5ff */
|
|
/* Read/Writable only while in Non-secure mode */
|
|
u32 kek[KEK_KEY_SIZE]; /* JDKEKR - Key Encryption Key */
|
|
u32 tkek[TKEK_KEY_SIZE]; /* TDKEKR - Trusted Desc KEK */
|
|
u32 tdsk[TDSK_KEY_SIZE]; /* TDSKR - Trusted Desc Signing Key */
|
|
u32 rsvd7[32];
|
|
u64 sknonce; /* SKNR - Secure Key Nonce */
|
|
u32 rsvd8[70];
|
|
|
|
/* RNG Test/Verification/Debug Access 600-7ff */
|
|
/* (Useful in Test/Debug modes only...) */
|
|
struct rngtst rtst[2];
|
|
|
|
u32 rsvd9[448];
|
|
|
|
/* Performance Monitor f00-fff */
|
|
struct caam_perfmon perfmon;
|
|
};
|
|
|
|
/*
|
|
* Controller master config register defs
|
|
*/
|
|
#define MCFGR_SWRESET 0x80000000 /* software reset */
|
|
#define MCFGR_WDENABLE 0x40000000 /* DECO watchdog enable */
|
|
#define MCFGR_WDFAIL 0x20000000 /* DECO watchdog force-fail */
|
|
#define MCFGR_DMA_RESET 0x10000000
|
|
#define MCFGR_LONG_PTR 0x00010000 /* Use >32-bit desc addressing */
|
|
|
|
/* AXI read cache control */
|
|
#define MCFGR_ARCACHE_SHIFT 12
|
|
#define MCFGR_ARCACHE_MASK (0xf << MCFGR_ARCACHE_SHIFT)
|
|
|
|
/* AXI write cache control */
|
|
#define MCFGR_AWCACHE_SHIFT 8
|
|
#define MCFGR_AWCACHE_MASK (0xf << MCFGR_AWCACHE_SHIFT)
|
|
|
|
/* AXI pipeline depth */
|
|
#define MCFGR_AXIPIPE_SHIFT 4
|
|
#define MCFGR_AXIPIPE_MASK (0xf << MCFGR_AXIPIPE_SHIFT)
|
|
|
|
#define MCFGR_AXIPRI 0x00000008 /* Assert AXI priority sideband */
|
|
#define MCFGR_BURST_64 0x00000001 /* Max burst size */
|
|
|
|
/*
|
|
* caam_job_ring - direct job ring setup
|
|
* 1-4 possible per instantiation, base + 1000/2000/3000/4000
|
|
* Padded out to 0x1000
|
|
*/
|
|
struct caam_job_ring {
|
|
/* Input ring */
|
|
u64 inpring_base; /* IRBAx - Input desc ring baseaddr */
|
|
u32 rsvd1;
|
|
u32 inpring_size; /* IRSx - Input ring size */
|
|
u32 rsvd2;
|
|
u32 inpring_avail; /* IRSAx - Input ring room remaining */
|
|
u32 rsvd3;
|
|
u32 inpring_jobadd; /* IRJAx - Input ring jobs added */
|
|
|
|
/* Output Ring */
|
|
u64 outring_base; /* ORBAx - Output status ring base addr */
|
|
u32 rsvd4;
|
|
u32 outring_size; /* ORSx - Output ring size */
|
|
u32 rsvd5;
|
|
u32 outring_rmvd; /* ORJRx - Output ring jobs removed */
|
|
u32 rsvd6;
|
|
u32 outring_used; /* ORSFx - Output ring slots full */
|
|
|
|
/* Status/Configuration */
|
|
u32 rsvd7;
|
|
u32 jroutstatus; /* JRSTAx - JobR output status */
|
|
u32 rsvd8;
|
|
u32 jrintstatus; /* JRINTx - JobR interrupt status */
|
|
u32 rconfig_hi; /* JRxCFG - Ring configuration */
|
|
u32 rconfig_lo;
|
|
|
|
/* Indices. CAAM maintains as "heads" of each queue */
|
|
u32 rsvd9;
|
|
u32 inp_rdidx; /* IRRIx - Input ring read index */
|
|
u32 rsvd10;
|
|
u32 out_wtidx; /* ORWIx - Output ring write index */
|
|
|
|
/* Command/control */
|
|
u32 rsvd11;
|
|
u32 jrcommand; /* JRCRx - JobR command */
|
|
|
|
u32 rsvd12[932];
|
|
|
|
/* Performance Monitor f00-fff */
|
|
struct caam_perfmon perfmon;
|
|
};
|
|
|
|
#define JR_RINGSIZE_MASK 0x03ff
|
|
/*
|
|
* jrstatus - Job Ring Output Status
|
|
* All values in lo word
|
|
* Also note, same values written out as status through QI
|
|
* in the command/status field of a frame descriptor
|
|
*/
|
|
#define JRSTA_SSRC_SHIFT 28
|
|
#define JRSTA_SSRC_MASK 0xf0000000
|
|
|
|
#define JRSTA_SSRC_NONE 0x00000000
|
|
#define JRSTA_SSRC_CCB_ERROR 0x20000000
|
|
#define JRSTA_SSRC_JUMP_HALT_USER 0x30000000
|
|
#define JRSTA_SSRC_DECO 0x40000000
|
|
#define JRSTA_SSRC_JRERROR 0x60000000
|
|
#define JRSTA_SSRC_JUMP_HALT_CC 0x70000000
|
|
|
|
#define JRSTA_DECOERR_JUMP 0x08000000
|
|
#define JRSTA_DECOERR_INDEX_SHIFT 8
|
|
#define JRSTA_DECOERR_INDEX_MASK 0xff00
|
|
#define JRSTA_DECOERR_ERROR_MASK 0x00ff
|
|
|
|
#define JRSTA_DECOERR_NONE 0x00
|
|
#define JRSTA_DECOERR_LINKLEN 0x01
|
|
#define JRSTA_DECOERR_LINKPTR 0x02
|
|
#define JRSTA_DECOERR_JRCTRL 0x03
|
|
#define JRSTA_DECOERR_DESCCMD 0x04
|
|
#define JRSTA_DECOERR_ORDER 0x05
|
|
#define JRSTA_DECOERR_KEYCMD 0x06
|
|
#define JRSTA_DECOERR_LOADCMD 0x07
|
|
#define JRSTA_DECOERR_STORECMD 0x08
|
|
#define JRSTA_DECOERR_OPCMD 0x09
|
|
#define JRSTA_DECOERR_FIFOLDCMD 0x0a
|
|
#define JRSTA_DECOERR_FIFOSTCMD 0x0b
|
|
#define JRSTA_DECOERR_MOVECMD 0x0c
|
|
#define JRSTA_DECOERR_JUMPCMD 0x0d
|
|
#define JRSTA_DECOERR_MATHCMD 0x0e
|
|
#define JRSTA_DECOERR_SHASHCMD 0x0f
|
|
#define JRSTA_DECOERR_SEQCMD 0x10
|
|
#define JRSTA_DECOERR_DECOINTERNAL 0x11
|
|
#define JRSTA_DECOERR_SHDESCHDR 0x12
|
|
#define JRSTA_DECOERR_HDRLEN 0x13
|
|
#define JRSTA_DECOERR_BURSTER 0x14
|
|
#define JRSTA_DECOERR_DESCSIGNATURE 0x15
|
|
#define JRSTA_DECOERR_DMA 0x16
|
|
#define JRSTA_DECOERR_BURSTFIFO 0x17
|
|
#define JRSTA_DECOERR_JRRESET 0x1a
|
|
#define JRSTA_DECOERR_JOBFAIL 0x1b
|
|
#define JRSTA_DECOERR_DNRERR 0x80
|
|
#define JRSTA_DECOERR_UNDEFPCL 0x81
|
|
#define JRSTA_DECOERR_PDBERR 0x82
|
|
#define JRSTA_DECOERR_ANRPLY_LATE 0x83
|
|
#define JRSTA_DECOERR_ANRPLY_REPLAY 0x84
|
|
#define JRSTA_DECOERR_SEQOVF 0x85
|
|
#define JRSTA_DECOERR_INVSIGN 0x86
|
|
#define JRSTA_DECOERR_DSASIGN 0x87
|
|
|
|
#define JRSTA_CCBERR_JUMP 0x08000000
|
|
#define JRSTA_CCBERR_INDEX_MASK 0xff00
|
|
#define JRSTA_CCBERR_INDEX_SHIFT 8
|
|
#define JRSTA_CCBERR_CHAID_MASK 0x00f0
|
|
#define JRSTA_CCBERR_CHAID_SHIFT 4
|
|
#define JRSTA_CCBERR_ERRID_MASK 0x000f
|
|
|
|
#define JRSTA_CCBERR_CHAID_AES (0x01 << JRSTA_CCBERR_CHAID_SHIFT)
|
|
#define JRSTA_CCBERR_CHAID_DES (0x02 << JRSTA_CCBERR_CHAID_SHIFT)
|
|
#define JRSTA_CCBERR_CHAID_ARC4 (0x03 << JRSTA_CCBERR_CHAID_SHIFT)
|
|
#define JRSTA_CCBERR_CHAID_MD (0x04 << JRSTA_CCBERR_CHAID_SHIFT)
|
|
#define JRSTA_CCBERR_CHAID_RNG (0x05 << JRSTA_CCBERR_CHAID_SHIFT)
|
|
#define JRSTA_CCBERR_CHAID_SNOW (0x06 << JRSTA_CCBERR_CHAID_SHIFT)
|
|
#define JRSTA_CCBERR_CHAID_KASUMI (0x07 << JRSTA_CCBERR_CHAID_SHIFT)
|
|
#define JRSTA_CCBERR_CHAID_PK (0x08 << JRSTA_CCBERR_CHAID_SHIFT)
|
|
#define JRSTA_CCBERR_CHAID_CRC (0x09 << JRSTA_CCBERR_CHAID_SHIFT)
|
|
|
|
#define JRSTA_CCBERR_ERRID_NONE 0x00
|
|
#define JRSTA_CCBERR_ERRID_MODE 0x01
|
|
#define JRSTA_CCBERR_ERRID_DATASIZ 0x02
|
|
#define JRSTA_CCBERR_ERRID_KEYSIZ 0x03
|
|
#define JRSTA_CCBERR_ERRID_PKAMEMSZ 0x04
|
|
#define JRSTA_CCBERR_ERRID_PKBMEMSZ 0x05
|
|
#define JRSTA_CCBERR_ERRID_SEQUENCE 0x06
|
|
#define JRSTA_CCBERR_ERRID_PKDIVZRO 0x07
|
|
#define JRSTA_CCBERR_ERRID_PKMODEVN 0x08
|
|
#define JRSTA_CCBERR_ERRID_KEYPARIT 0x09
|
|
#define JRSTA_CCBERR_ERRID_ICVCHK 0x0a
|
|
#define JRSTA_CCBERR_ERRID_HARDWARE 0x0b
|
|
#define JRSTA_CCBERR_ERRID_CCMAAD 0x0c
|
|
#define JRSTA_CCBERR_ERRID_INVCHA 0x0f
|
|
|
|
#define JRINT_ERR_INDEX_MASK 0x3fff0000
|
|
#define JRINT_ERR_INDEX_SHIFT 16
|
|
#define JRINT_ERR_TYPE_MASK 0xf00
|
|
#define JRINT_ERR_TYPE_SHIFT 8
|
|
#define JRINT_ERR_HALT_MASK 0xc
|
|
#define JRINT_ERR_HALT_SHIFT 2
|
|
#define JRINT_ERR_HALT_INPROGRESS 0x4
|
|
#define JRINT_ERR_HALT_COMPLETE 0x8
|
|
#define JRINT_JR_ERROR 0x02
|
|
#define JRINT_JR_INT 0x01
|
|
|
|
#define JRINT_ERR_TYPE_WRITE 1
|
|
#define JRINT_ERR_TYPE_BAD_INPADDR 3
|
|
#define JRINT_ERR_TYPE_BAD_OUTADDR 4
|
|
#define JRINT_ERR_TYPE_INV_INPWRT 5
|
|
#define JRINT_ERR_TYPE_INV_OUTWRT 6
|
|
#define JRINT_ERR_TYPE_RESET 7
|
|
#define JRINT_ERR_TYPE_REMOVE_OFL 8
|
|
#define JRINT_ERR_TYPE_ADD_OFL 9
|
|
|
|
#define JRCFG_SOE 0x04
|
|
#define JRCFG_ICEN 0x02
|
|
#define JRCFG_IMSK 0x01
|
|
#define JRCFG_ICDCT_SHIFT 8
|
|
#define JRCFG_ICTT_SHIFT 16
|
|
|
|
#define JRCR_RESET 0x01
|
|
|
|
/*
|
|
* caam_assurance - Assurance Controller View
|
|
* base + 0x6000 padded out to 0x1000
|
|
*/
|
|
|
|
struct rtic_element {
|
|
u64 address;
|
|
u32 rsvd;
|
|
u32 length;
|
|
};
|
|
|
|
struct rtic_block {
|
|
struct rtic_element element[2];
|
|
};
|
|
|
|
struct rtic_memhash {
|
|
u32 memhash_be[32];
|
|
u32 memhash_le[32];
|
|
};
|
|
|
|
struct caam_assurance {
|
|
/* Status/Command/Watchdog */
|
|
u32 rsvd1;
|
|
u32 status; /* RSTA - Status */
|
|
u32 rsvd2;
|
|
u32 cmd; /* RCMD - Command */
|
|
u32 rsvd3;
|
|
u32 ctrl; /* RCTL - Control */
|
|
u32 rsvd4;
|
|
u32 throttle; /* RTHR - Throttle */
|
|
u32 rsvd5[2];
|
|
u64 watchdog; /* RWDOG - Watchdog Timer */
|
|
u32 rsvd6;
|
|
u32 rend; /* REND - Endian corrections */
|
|
u32 rsvd7[50];
|
|
|
|
/* Block access/configuration @ 100/110/120/130 */
|
|
struct rtic_block memblk[4]; /* Memory Blocks A-D */
|
|
u32 rsvd8[32];
|
|
|
|
/* Block hashes @ 200/300/400/500 */
|
|
struct rtic_memhash hash[4]; /* Block hash values A-D */
|
|
u32 rsvd_3[640];
|
|
};
|
|
|
|
/*
|
|
* caam_queue_if - QI configuration and control
|
|
* starts base + 0x7000, padded out to 0x1000 long
|
|
*/
|
|
|
|
struct caam_queue_if {
|
|
u32 qi_control_hi; /* QICTL - QI Control */
|
|
u32 qi_control_lo;
|
|
u32 rsvd1;
|
|
u32 qi_status; /* QISTA - QI Status */
|
|
u32 qi_deq_cfg_hi; /* QIDQC - QI Dequeue Configuration */
|
|
u32 qi_deq_cfg_lo;
|
|
u32 qi_enq_cfg_hi; /* QISEQC - QI Enqueue Command */
|
|
u32 qi_enq_cfg_lo;
|
|
u32 rsvd2[1016];
|
|
};
|
|
|
|
/* QI control bits - low word */
|
|
#define QICTL_DQEN 0x01 /* Enable frame pop */
|
|
#define QICTL_STOP 0x02 /* Stop dequeue/enqueue */
|
|
#define QICTL_SOE 0x04 /* Stop on error */
|
|
|
|
/* QI control bits - high word */
|
|
#define QICTL_MBSI 0x01
|
|
#define QICTL_MHWSI 0x02
|
|
#define QICTL_MWSI 0x04
|
|
#define QICTL_MDWSI 0x08
|
|
#define QICTL_CBSI 0x10 /* CtrlDataByteSwapInput */
|
|
#define QICTL_CHWSI 0x20 /* CtrlDataHalfSwapInput */
|
|
#define QICTL_CWSI 0x40 /* CtrlDataWordSwapInput */
|
|
#define QICTL_CDWSI 0x80 /* CtrlDataDWordSwapInput */
|
|
#define QICTL_MBSO 0x0100
|
|
#define QICTL_MHWSO 0x0200
|
|
#define QICTL_MWSO 0x0400
|
|
#define QICTL_MDWSO 0x0800
|
|
#define QICTL_CBSO 0x1000 /* CtrlDataByteSwapOutput */
|
|
#define QICTL_CHWSO 0x2000 /* CtrlDataHalfSwapOutput */
|
|
#define QICTL_CWSO 0x4000 /* CtrlDataWordSwapOutput */
|
|
#define QICTL_CDWSO 0x8000 /* CtrlDataDWordSwapOutput */
|
|
#define QICTL_DMBS 0x010000
|
|
#define QICTL_EPO 0x020000
|
|
|
|
/* QI status bits */
|
|
#define QISTA_PHRDERR 0x01 /* PreHeader Read Error */
|
|
#define QISTA_CFRDERR 0x02 /* Compound Frame Read Error */
|
|
#define QISTA_OFWRERR 0x04 /* Output Frame Read Error */
|
|
#define QISTA_BPDERR 0x08 /* Buffer Pool Depleted */
|
|
#define QISTA_BTSERR 0x10 /* Buffer Undersize */
|
|
#define QISTA_CFWRERR 0x20 /* Compound Frame Write Err */
|
|
#define QISTA_STOPD 0x80000000 /* QI Stopped (see QICTL) */
|
|
|
|
/* deco_sg_table - DECO view of scatter/gather table */
|
|
struct deco_sg_table {
|
|
u64 addr; /* Segment Address */
|
|
u32 elen; /* E, F bits + 30-bit length */
|
|
u32 bpid_offset; /* Buffer Pool ID + 16-bit length */
|
|
};
|
|
|
|
/*
|
|
* caam_deco - descriptor controller - CHA cluster block
|
|
*
|
|
* Only accessible when direct DECO access is turned on
|
|
* (done in DECORR, via MID programmed in DECOxMID
|
|
*
|
|
* 5 typical, base + 0x8000/9000/a000/b000
|
|
* Padded out to 0x1000 long
|
|
*/
|
|
struct caam_deco {
|
|
u32 rsvd1;
|
|
u32 cls1_mode; /* CxC1MR - Class 1 Mode */
|
|
u32 rsvd2;
|
|
u32 cls1_keysize; /* CxC1KSR - Class 1 Key Size */
|
|
u32 cls1_datasize_hi; /* CxC1DSR - Class 1 Data Size */
|
|
u32 cls1_datasize_lo;
|
|
u32 rsvd3;
|
|
u32 cls1_icvsize; /* CxC1ICVSR - Class 1 ICV size */
|
|
u32 rsvd4[5];
|
|
u32 cha_ctrl; /* CCTLR - CHA control */
|
|
u32 rsvd5;
|
|
u32 irq_crtl; /* CxCIRQ - CCB interrupt done/error/clear */
|
|
u32 rsvd6;
|
|
u32 clr_written; /* CxCWR - Clear-Written */
|
|
u32 ccb_status_hi; /* CxCSTA - CCB Status/Error */
|
|
u32 ccb_status_lo;
|
|
u32 rsvd7[3];
|
|
u32 aad_size; /* CxAADSZR - Current AAD Size */
|
|
u32 rsvd8;
|
|
u32 cls1_iv_size; /* CxC1IVSZR - Current Class 1 IV Size */
|
|
u32 rsvd9[7];
|
|
u32 pkha_a_size; /* PKASZRx - Size of PKHA A */
|
|
u32 rsvd10;
|
|
u32 pkha_b_size; /* PKBSZRx - Size of PKHA B */
|
|
u32 rsvd11;
|
|
u32 pkha_n_size; /* PKNSZRx - Size of PKHA N */
|
|
u32 rsvd12;
|
|
u32 pkha_e_size; /* PKESZRx - Size of PKHA E */
|
|
u32 rsvd13[24];
|
|
u32 cls1_ctx[16]; /* CxC1CTXR - Class 1 Context @100 */
|
|
u32 rsvd14[48];
|
|
u32 cls1_key[8]; /* CxC1KEYR - Class 1 Key @200 */
|
|
u32 rsvd15[121];
|
|
u32 cls2_mode; /* CxC2MR - Class 2 Mode */
|
|
u32 rsvd16;
|
|
u32 cls2_keysize; /* CxX2KSR - Class 2 Key Size */
|
|
u32 cls2_datasize_hi; /* CxC2DSR - Class 2 Data Size */
|
|
u32 cls2_datasize_lo;
|
|
u32 rsvd17;
|
|
u32 cls2_icvsize; /* CxC2ICVSZR - Class 2 ICV Size */
|
|
u32 rsvd18[56];
|
|
u32 cls2_ctx[18]; /* CxC2CTXR - Class 2 Context @500 */
|
|
u32 rsvd19[46];
|
|
u32 cls2_key[32]; /* CxC2KEYR - Class2 Key @600 */
|
|
u32 rsvd20[84];
|
|
u32 inp_infofifo_hi; /* CxIFIFO - Input Info FIFO @7d0 */
|
|
u32 inp_infofifo_lo;
|
|
u32 rsvd21[2];
|
|
u64 inp_datafifo; /* CxDFIFO - Input Data FIFO */
|
|
u32 rsvd22[2];
|
|
u64 out_datafifo; /* CxOFIFO - Output Data FIFO */
|
|
u32 rsvd23[2];
|
|
u32 jr_ctl_hi; /* CxJRR - JobR Control Register @800 */
|
|
u32 jr_ctl_lo;
|
|
u64 jr_descaddr; /* CxDADR - JobR Descriptor Address */
|
|
u32 op_status_hi; /* DxOPSTA - DECO Operation Status */
|
|
u32 op_status_lo;
|
|
u32 rsvd24[2];
|
|
u32 liodn; /* DxLSR - DECO LIODN Status - non-seq */
|
|
u32 td_liodn; /* DxLSR - DECO LIODN Status - trustdesc */
|
|
u32 rsvd26[6];
|
|
u64 math[4]; /* DxMTH - Math register */
|
|
u32 rsvd27[8];
|
|
struct deco_sg_table gthr_tbl[4]; /* DxGTR - Gather Tables */
|
|
u32 rsvd28[16];
|
|
struct deco_sg_table sctr_tbl[4]; /* DxSTR - Scatter Tables */
|
|
u32 rsvd29[48];
|
|
u32 descbuf[64]; /* DxDESB - Descriptor buffer */
|
|
u32 rsvd30[320];
|
|
};
|
|
|
|
/*
|
|
* Current top-level view of memory map is:
|
|
*
|
|
* 0x0000 - 0x0fff - CAAM Top-Level Control
|
|
* 0x1000 - 0x1fff - Job Ring 0
|
|
* 0x2000 - 0x2fff - Job Ring 1
|
|
* 0x3000 - 0x3fff - Job Ring 2
|
|
* 0x4000 - 0x4fff - Job Ring 3
|
|
* 0x5000 - 0x5fff - (unused)
|
|
* 0x6000 - 0x6fff - Assurance Controller
|
|
* 0x7000 - 0x7fff - Queue Interface
|
|
* 0x8000 - 0x8fff - DECO-CCB 0
|
|
* 0x9000 - 0x9fff - DECO-CCB 1
|
|
* 0xa000 - 0xafff - DECO-CCB 2
|
|
* 0xb000 - 0xbfff - DECO-CCB 3
|
|
* 0xc000 - 0xcfff - DECO-CCB 4
|
|
*
|
|
* caam_full describes the full register view of CAAM if useful,
|
|
* although many configurations may choose to implement parts of
|
|
* the register map separately, in differing privilege regions
|
|
*/
|
|
struct caam_full {
|
|
struct caam_ctrl __iomem ctrl;
|
|
struct caam_job_ring jr[4];
|
|
u64 rsvd[512];
|
|
struct caam_assurance assure;
|
|
struct caam_queue_if qi;
|
|
};
|
|
|
|
#endif /* REGS_H */
|