qemu-e2k/default-configs/mips64el-softmmu.mak

15 lines
284 B
Makefile
Raw Normal View History

# Default configuration for mips64el-softmmu
include mips-softmmu-common.mak
CONFIG_IDE_VIA=y
CONFIG_FULONG=y
hw/mips/Kconfig: Fulong 2e board requires ati-vga/rtl8139 PCI devices This fixes when configuring with --without-default-devices: $ qemu-system-mips64el -bios /dev/null -M fulong2e qemu-system-mips64el: Unknown device 'ati-vga' for bus 'PCI' Aborted (core dumped) (gdb) bt #0 0x00007ffff5a2753f in __GI_raise (sig=sig@entry=6) at ../sysdeps/unix/sysv/linux/raise.c:50 #1 0x00007ffff5a11895 in __GI_abort () at abort.c:79 #2 0x00005555558768d3 in qdev_create (bus=bus@entry=0x5555562664b0, name=name@entry=0x555555b24efb "ati-vga") at hw/core/qdev.c:131 #3 0x00005555558d15e1 in pci_create_multifunction (bus=bus@entry=0x5555562664b0, devfn=devfn@entry=-1, multifunction=multifunction@entry=false, name=name@entry=0x555555b24efb "ati-vga") at hw/pci/pci.c:2104 #4 0x00005555558d1a7a in pci_create (bus=bus@entry=0x5555562664b0, devfn=devfn@entry=-1, name=name@entry=0x555555b24efb "ati-vga") at hw/pci/pci.c:2121 #5 0x0000555555763081 in mips_fulong2e_init (machine=<optimized out>) at hw/mips/mips_fulong2e.c:352 #6 0x000055555587e23b in machine_run_board_init (machine=0x5555560b2000) at hw/core/machine.c:1030 #7 0x00005555556cbea2 in main (argc=<optimized out>, argv=<optimized out>, envp=<optimized out>) at vl.c:4463 And then: $ qemu-system-mips64el -bios /dev/null -M fulong2e qemu-system-mips64el: Unsupported NIC model: rtl8139 Fixes: 862b4a291dc and 7c28b925b7e Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com> Message-Id: <20190316200818.8265-8-philmd@redhat.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2019-03-16 21:08:11 +01:00
CONFIG_ATI_VGA=y
CONFIG_RTL8139_PCI=y
CONFIG_JAZZ=y
CONFIG_VT82C686=y
CONFIG_AHCI=y
hw/mips: MIPS Boston board support Introduce support for emulating the MIPS Boston development board. The Boston board is built around an FPGA & 3 PCIe controllers, one of which is connected to an Intel EG20T Platform Controller Hub. It is used during the development & debug of new CPUs and the software intended to run on them, and is essentially the successor to the older MIPS Malta board. This patch does not implement the EG20T, instead connecting an already supported ICH-9 AHCI controller. Whilst this isn't accurate it's enough for typical stock Boston software (eg. Linux kernels) to work with hard disks given that both the ICH-9 & EG20T implement the AHCI specification. Boston boards typically boot kernels in the FIT image format, and this patch will treat kernels provided to QEMU as such. When loading a kernel directly, the board code will generate minimal firmware much as the Malta board code does. This firmware will set up the CM, CPC & GIC register base addresses then set argument registers & jump to the kernel entry point. Alternatively, bootloader code may be loaded using the bios argument in which case no firmware will be generated & execution will proceed from the start of the boot code at the default MIPS boot exception vector (offset 0x1fc00000 into (c)kseg1). Currently real Boston boards are always used with FPGA bitfiles that include a Global Interrupt Controller (GIC), so the interrupt configuration is only defined for such cases. Therefore the board will only allow use of CPUs which implement the CPS components, including the GIC, and will otherwise exit with a message. Signed-off-by: Paul Burton <paul.burton@imgtec.com> Reviewed-by: Yongbok Kim <yongbok.kim@imgtec.com> [yongbok.kim@imgtec.com: isolated boston machine support for mips64el. updated for recent Chardev changes. ignore missing bios/kernel for qtest. added default -drive to if=ide explicitly. changed default memory size into 1G due to make check failure on 32-bit hosts] Signed-off-by: Yongbok Kim <yongbok.kim@imgtec.com>
2016-09-08 16:51:58 +02:00
CONFIG_MIPS_BOSTON=y
CONFIG_FITLOADER=y
CONFIG_PCI_EXPRESS=y
CONFIG_PCI_EXPRESS_XILINX=y