sm501: Use defined constants instead of literal values where available
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu> Reviewed-by: Peter Maydell <peter.maydell@linaro.org> Tested-by: Aurelien Jarno <aurelien@aurel32.net> Message-id: 31205c2df623e7b133ef942ff4f5e95fff800a14.1492787889.git.balaton@eik.bme.hu Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This commit is contained in:
parent
64f1603b07
commit
e2ee84760e
@ -23,6 +23,7 @@
|
||||
*/
|
||||
|
||||
#include "qemu/osdep.h"
|
||||
#include "qemu/cutils.h"
|
||||
#include "qapi/error.h"
|
||||
#include "qemu-common.h"
|
||||
#include "cpu.h"
|
||||
@ -446,12 +447,12 @@
|
||||
|
||||
/* SM501 local memory size taken from "linux/drivers/mfd/sm501.c" */
|
||||
static const uint32_t sm501_mem_local_size[] = {
|
||||
[0] = 4 * 1024 * 1024,
|
||||
[1] = 8 * 1024 * 1024,
|
||||
[2] = 16 * 1024 * 1024,
|
||||
[3] = 32 * 1024 * 1024,
|
||||
[4] = 64 * 1024 * 1024,
|
||||
[5] = 2 * 1024 * 1024,
|
||||
[0] = 4 * M_BYTE,
|
||||
[1] = 8 * M_BYTE,
|
||||
[2] = 16 * M_BYTE,
|
||||
[3] = 32 * M_BYTE,
|
||||
[4] = 64 * M_BYTE,
|
||||
[5] = 2 * M_BYTE,
|
||||
};
|
||||
#define get_local_mem_size(s) sm501_mem_local_size[(s)->local_mem_size_index]
|
||||
|
||||
@ -555,7 +556,7 @@ static uint32_t get_local_mem_size_index(uint32_t size)
|
||||
static inline int is_hwc_enabled(SM501State *state, int crt)
|
||||
{
|
||||
uint32_t addr = crt ? state->dc_crt_hwc_addr : state->dc_panel_hwc_addr;
|
||||
return addr & 0x80000000;
|
||||
return addr & SM501_HWC_EN;
|
||||
}
|
||||
|
||||
/**
|
||||
@ -1411,9 +1412,17 @@ void sm501_init(MemoryRegion *address_space_mem, uint32_t base,
|
||||
s->local_mem_size_index = get_local_mem_size_index(local_mem_bytes);
|
||||
SM501_DPRINTF("local mem size=%x. index=%d\n", get_local_mem_size(s),
|
||||
s->local_mem_size_index);
|
||||
s->system_control = 0x00100000;
|
||||
s->misc_control = 0x00001000; /* assumes SH, active=low */
|
||||
s->dc_panel_control = 0x00010000;
|
||||
s->system_control = 0x00100000; /* 2D engine FIFO empty */
|
||||
/* Bits 17 (SH), 7 (CDR), 6:5 (Test), 2:0 (Bus) are all supposed
|
||||
* to be determined at reset by GPIO lines which set config bits.
|
||||
* We hardwire them:
|
||||
* SH = 0 : Hitachi Ready Polarity == Active Low
|
||||
* CDR = 0 : do not reset clock divider
|
||||
* TEST = 0 : Normal mode (not testing the silicon)
|
||||
* BUS = 0 : Hitachi SH3/SH4
|
||||
*/
|
||||
s->misc_control = SM501_MISC_DAC_POWER;
|
||||
s->dc_panel_control = 0x00010000; /* FIFO level 3 */
|
||||
s->dc_crt_control = 0x00010000;
|
||||
|
||||
/* allocate local memory */
|
||||
|
@ -108,7 +108,7 @@ static void glue(draw_hwc_line_, PIXEL_NAME)(SM501State *s, int crt,
|
||||
/* get hardware cursor pattern */
|
||||
uint32_t cursor_addr = get_hwc_address(s, crt);
|
||||
assert(0 <= c_y && c_y < SM501_HWC_HEIGHT);
|
||||
cursor_addr += 64 * c_y / 4; /* 4 pixels per byte */
|
||||
cursor_addr += SM501_HWC_WIDTH * c_y / 4; /* 4 pixels per byte */
|
||||
cursor_addr += s->base;
|
||||
|
||||
/* get cursor position */
|
||||
|
Loading…
Reference in New Issue
Block a user