On exception return for v8M, the SPSEL bit in the EXC_RETURN magic
value should be restored to the SPSEL bit in the CONTROL register
banked specified by the EXC_RETURN.ES bit.
Add write_v7m_control_spsel_for_secstate() which behaves like
write_v7m_control_spsel() but allows the caller to specify which
CONTROL bank to use, reimplement write_v7m_control_spsel() in
terms of it, and use it in exception return.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1506092407-26985-6-git-send-email-peter.maydell@linaro.org
Now that we can handle the CONTROL.SPSEL bit not necessarily being
in sync with the current stack pointer, we can restore the correct
security state on exception return. This happens before we start
to read registers off the stack frame, but after we have taken
possible usage faults for bad exception return magic values and
updated CONTROL.SPSEL.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1506092407-26985-5-git-send-email-peter.maydell@linaro.org
In the v7M architecture, there is an invariant that if the CPU is
in Handler mode then the CONTROL.SPSEL bit cannot be nonzero.
This in turn means that the current stack pointer is always
indicated by CONTROL.SPSEL, even though Handler mode always uses
the Main stack pointer.
In v8M, this invariant is removed, and CONTROL.SPSEL may now
be nonzero in Handler mode (though Handler mode still always
uses the Main stack pointer). In preparation for this change,
change how we handle this bit: rename switch_v7m_sp() to
the now more accurate write_v7m_control_spsel(), and make it
check both the handler mode state and the SPSEL bit.
Note that this implicitly changes the point at which we switch
active SP on exception exit from before we pop the exception
frame to after it.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1506092407-26985-4-git-send-email-peter.maydell@linaro.org
Currently our M profile exception return code switches to the
target stack pointer relatively early in the process, before
it tries to pop the exception frame off the stack. This is
awkward for v8M for two reasons:
* in v8M the process vs main stack pointer is not selected
purely by the value of CONTROL.SPSEL, so updating SPSEL
and relying on that to switch to the right stack pointer
won't work
* the stack we should be reading the stack frame from and
the stack we will eventually switch to might not be the
same if the guest is doing strange things
Change our exception return code to use a 'frame pointer'
to read the exception frame rather than assuming that we
can switch the live stack pointer this early.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1506092407-26985-3-git-send-email-peter.maydell@linaro.org
Reset for devices does not include an automatic clear of the
device state (unlike CPU state, where most of the state
structure is cleared to zero). Add some missing initialization
of NVIC state that meant that the device was left in the wrong
state if the guest did a warm reset.
(In particular, since we were resetting the computed state like
s->exception_prio but not all the state it was computed
from like s->vectors[x].active, the NVIC wound up in an
inconsistent state that could later trigger assertion failures.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 1506092407-26985-2-git-send-email-peter.maydell@linaro.org
The device uses serial_hds in its realize function and thus can't be
used twice. Apart from that, the comma in its name makes it quite hard
to use for the user anyway, since a comma is normally used to separate
the device name from its properties when using the "-device" parameter
or the "device_add" HMP command.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 1506441116-16627-1-git-send-email-thuth@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The current code checks if the next block exceeds the size of the card.
This generates an error while reading the last block of the card.
Do the out-of-bounds check when starting to read a new block to fix this.
This issue became visible with increased error checking in Linux 4.13.
Cc: qemu-stable@nongnu.org
Signed-off-by: Michael Olbrich <m.olbrich@pengutronix.de>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 20170916091611.10241-1-m.olbrich@pengutronix.de
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This properly forwards SMC events to EL2 when PSCI is provided by QEMU
itself and, thus, ARM_FEATURE_EL3 is off.
Found and tested with the Jailhouse hypervisor. Solution based on
suggestions by Peter Maydell.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Message-id: 4f243068-aaea-776f-d18f-f9e05e7be9cd@siemens.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJZ15OhAAoJEPQH2wBh1c9AELcIAIrqRUvlIWw9VTq53x6sLbJJ
dLJ6D2gUaa+ove93dvP8OwES/SDqyxkOZUHZ5ctOXxGYAM6QLfu1Z9Rv9XHhS3Ef
gCKdvSuCEHGzYxU7BLbB621syzV71uQk91nXsUEX5jICLKa5wa6XEuqMgsmasa6b
K1aQbTLgJ7FeT4EOTXkDMQdQDaa12KPOyEopv9Fy+App1jk/OjlAAMSTz09tcVep
eCKn8Q1G51RkaPQPa1yquKz8KOLOYSheSSzg6ujgWUdq4VNeaNUlgjqlVWeK1oWD
+3izXFO2dCoBcmRMLT5V4pVXeoK1KdPSNfbM1lb8c4vzwTQyo4g5J3TuP/2QaZg=
=LxEj
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'mreitz/tags/pull-block-2017-10-06' into queue-block
Block patches
# gpg: Signature made Fri Oct 6 16:30:57 2017 CEST
# gpg: using RSA key F407DB0061D5CF40
# gpg: Good signature from "Max Reitz <mreitz@redhat.com>"
# Primary key fingerprint: 91BE B60A 30DB 3E88 57D1 1829 F407 DB00 61D5 CF40
* mreitz/tags/pull-block-2017-10-06:
block/mirror: check backing in bdrv_mirror_top_flush
qcow2: truncate the tail of the image file after shrinking the image
qcow2: fix return error code in qcow2_truncate()
iotests: Fix 195 if IMGFMT is part of TEST_DIR
block/mirror: check backing in bdrv_mirror_top_refresh_filename
block: support passthrough of BDRV_REQ_FUA in crypto driver
block: convert qcrypto_block_encrypt|decrypt to take bytes offset
block: convert crypto driver to bdrv_co_preadv|pwritev
block: fix data type casting for crypto payload offset
crypto: expose encryption sector size in APIs
block: use 1 MB bounce buffers for crypto instead of 16KB
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Backing may be zero after failed bdrv_append in mirror_start_job,
which leads to SIGSEGV.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-id: 20170929152255.5431-1-vsementsov@virtuozzo.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
Now after shrinking the image, at the end of the image file, there might be a
tail that probably will never be used. So we can find the last used cluster and
cut the tail.
Signed-off-by: Pavel Butsykin <pbutsykin@virtuozzo.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Message-id: 20170929121613.25997-3-pbutsykin@virtuozzo.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Pavel Butsykin <pbutsykin@virtuozzo.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Message-id: 20170929121613.25997-2-pbutsykin@virtuozzo.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
do_run_qemu() in iotest 195 first applies _filter_imgfmt when printing
qemu's command line and _filter_testdir only afterwards. Therefore, if
the image format is part of the test directory path, _filter_testdir
will no longer apply and the actual output will differ from the
reference output even in case of success.
For example, TEST_DIR might be "/tmp/test-qcow2", in which case
_filter_imgfmt first transforms this to "/tmp/test-IMGFMT" which is no
longer recognized as the TEST_DIR by _filter_testdir.
Fix this by not applying _filter_imgfmt in do_run_qemu() but in
run_qemu() instead, and only after _filter_testdir.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Message-id: 20170927211334.3988-1-mreitz@redhat.com
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
Backing may be zero after failed bdrv_attach_child in
bdrv_set_backing_hd, which leads to SIGSEGV.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-id: 20170928120300.58164-1-vsementsov@virtuozzo.com
Reviewed-by: John Snow <jsnow@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
The BDRV_REQ_FUA flag can trivially be allowed in the crypt driver
as a passthrough to the underlying block driver.
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 20170927125340.12360-7-berrange@redhat.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
Instead of sector offset, take the bytes offset when encrypting
or decrypting data.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 20170927125340.12360-6-berrange@redhat.com
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
Make the crypto driver implement the bdrv_co_preadv|pwritev
callbacks, and also use bdrv_co_preadv|pwritev for I/O
with the protocol driver beneath. This replaces sector based
I/O with byte based I/O, and allows us to stop assuming the
physical sector size matches the encryption sector size.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 20170927125340.12360-5-berrange@redhat.com
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
The crypto APIs report the offset of the data payload as an uint64_t
type, but the block driver is casting to size_t or ssize_t which will
potentially truncate.
Most of the block APIs use int64_t for offsets meanwhile, so even if
using uint64_t in the crypto block driver we are still at risk of
truncation.
Change the block crypto driver to use uint64_t, but add asserts that
the value is less than INT64_MAX.
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 20170927125340.12360-4-berrange@redhat.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
While current encryption schemes all have a fixed sector size of
512 bytes, this is not guaranteed to be the case in future. Expose
the sector size in the APIs so the block layer can remove assumptions
about fixed 512 byte sectors.
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 20170927125340.12360-3-berrange@redhat.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
Using 16KB bounce buffers creates a significant performance
penalty for I/O to encrypted volumes on storage which high
I/O latency (rotating rust & network drives), because it
triggers lots of fairly small I/O operations.
On tests with rotating rust, and cache=none|directsync,
write speed increased from 2MiB/s to 32MiB/s, on a par
with that achieved by the in-kernel luks driver. With
other cache modes the in-kernel driver is still notably
faster because it is able to report completion of the
I/O request before any encryption is done, while the
in-QEMU driver must encrypt the data before completion.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 20170927125340.12360-2-berrange@redhat.com
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
Add a test for qcow2 copy-on-read behavior, including exposure
for the just-fixed bugs.
The copy-on-read behavior is always to a qcow2 image, but the
test is careful to allow running with most image protocol/format
combos as the backing file being copied from (luks being the
exception, as it is harder to pass the right secret to all the
right places). In fact, for './check nbd', this appears to be
the first time we've had a qcow2 image wrapping NBD, requiring
an additional line in _filter_img_create to match the similar
line in _filter_img_info.
Invoking blkdebug to prove we don't write too much took some
effort to get working; and it requires that $TEST_WRAP (based
on $TEST_DIR) not be subject to word splitting. We may decide
later to have the entire iotests suite use relative rather than
absolute names, to avoid problems inherited by the absolute
name of $PWD or $TEST_DIR, at which point the sanity check in
this commit could be simplified.
This test requires at least 2G of consecutive memory to succeed;
as such, it is prone to spurious failures, particularly on
32-bit machines under load. This situation is detected and
triggers an early exit to skip the test, rather than a failure.
To manually provoke this setup on a beefier machine, I used:
$ (ulimit -S -v 1000000; ./check -qcow2 197)
Signed-off-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Improve our braindead copy-on-read implementation. Pre-patch,
we have multiple issues:
- we create a bounce buffer and perform a write for the entire
request, even if the active image already has 99% of the
clusters occupied, and really only needs to copy-on-read the
remaining 1% of the clusters
- our bounce buffer was as large as the read request, and can
needlessly exhaust our memory by using double the memory of
the request size (the original request plus our bounce buffer),
rather than a capped maximum overhead beyond the original
- if a driver has a max_transfer limit, we are bypassing the
normal code in bdrv_aligned_preadv() that fragments to that
limit, and instead attempt to read the entire buffer from the
driver in one go, which some drivers may assert on
- a client can request a large request of nearly 2G such that
rounding the request out to cluster boundaries results in a
byte count larger than 2G. While this cannot exceed 32 bits,
it DOES have some follow-on problems:
-- the call to bdrv_driver_pread() can assert for exceeding
BDRV_REQUEST_MAX_BYTES, if the driver is old and lacks
.bdrv_co_preadv
-- if the buffer is all zeroes, the subsequent call to
bdrv_co_do_pwrite_zeroes is a no-op due to a negative size,
which means we did not actually copy on read
Fix all of these issues by breaking up the action into a loop,
where each iteration is capped to sane limits. Also, querying
the allocation status allows us to optimize: when data is
already present in the active layer, we don't need to bounce.
Note that the code has a telling comment that copy-on-read
should probably be a filter driver rather than a bolt-on hack
in io.c; but that remains a task for another day.
CC: qemu-stable@nongnu.org
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Make it possible to inject errors on writes performed during a
read operation due to copy-on-read semantics.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Jeff Cody <jcody@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Executing qemu with a terminal as stdin will temporarily alter stty
settings on that terminal (for example, disabling echo), because of
how we run both the monitor and any multiplexing with guest input.
Normally, qemu restores the original settings on exit; but if an
iotest triggers qemu to abort in the middle, we can be left with
the altered terminal setup. This can make life very annoying when
debugging an iotest failure (not everyone remembers the trick of
blind-typing 'stty sane' without echo, and some people prefer
terminal settings that are slightly different than the defaults
picked by 'stty sane').
It is possible to avoid qemu corrupting the terminal by not passing
a terminal to qemu's stdin in the first place (as in, use
'./check ... </dev/null'), but that's extra typing to have to
remember. But running 'exec </dev/null' in the harness seems like
it might be too heavy of a hammer. So I instead went the the
solution of saving and restoring the stty settings, only when the
harness detects that it is run interactively.
I tested this patch by forcing an allocation failure (I can't
guarantee that this particular limit will work on all setups, but
it shows the idea):
$ (ulimit -S -v 500000; ./check -qcow2 1)
Signed-off-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Handle a 0-length block status request up front, with a uniform
return value claiming the area is not allocated.
Most callers don't pass a length of 0 to bdrv_get_block_status()
and friends; but it definitely happens with a 0-length read when
copy-on-read is enabled. While we could audit all callers to
ensure that they never make a 0-length request, and then assert
that fact, it was just as easy to fix things to always report
success (as long as the callers are careful to not go into an
infinite loop). However, we had inconsistent behavior on whether
the status is reported as allocated or defers to the backing
layer, depending on what callbacks the driver implements, and
possibly wasting quite a few CPU cycles to get to that answer.
Consistently reporting unallocated up front doesn't really hurt
anything, and makes it easier both for callers (0-length requests
now have well-defined behavior) and for drivers (drivers don't
have to deal with 0-length requests).
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Make it easier to enable copy-on-read during iotests, by
exposing a new bool option to main and open.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Jeff Cody <jcody@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
We don't need to make any assumptions about the graph layout above the
top node of the commit operation any more. Remove the use of
bdrv_find_overlay() and related variables from the commit job code.
bdrv_drop_intermediate() doesn't use the 'active' parameter any more, so
we can just drop it.
The overlay node was previously added to the block job to get a
BLK_PERM_GRAPH_MOD. We really need to respect those permissions in
bdrv_drop_intermediate() now, but as long as we haven't figured out yet
how BLK_PERM_GRAPH_MOD is actually supposed to work, just leave a TODO
comment there.
With this change, it is now possible to perform another block job on an
overlay node without conflicts. qemu-iotests 030 is changed accordingly.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
QMP responses to certain commands can become quite long, which doesn't
only make reading them hard, but also means that the maximum line length
in patch emails can be exceeded. Allow tests to switch to QMP pretty
printing, which results in more, but shorter lines.
We also need to make sure to keep indentation in the response for this
to work as expected.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
This changes the commit block job to support operation in a graph where
there is more than a single active layer that references the top node.
This involves inserting the commit filter node not only on the path
between the given active node and the top node, but between the top node
and all of its parents.
On completion, bdrv_drop_intermediate() must consider all parents for
updating the backing file link. These parents may be backing files
themselves and as such read-only; reopen them temporarily if necessary.
Previously this was achieved by the bdrv_reopen() calls in the commit
block job that made overlay_bs read-write for the whole duration of the
block job, even though write access is only needed on completion.
Now that we consider all parents, overlay_bs is meaningless. It is left
in place in this commit, but we'll remove it soon.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
There is no good reason for bdrv_drop_intermediate() to know the active
layer above the subchain it is operating on - even more so, because
the assumption that there is a single active layer above it is not
generally true.
In order to prepare removal of the active parameter, use a BdrvChildRole
callback to update the backing file string in the overlay image instead
of directly calling bdrv_change_backing_file().
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
"check" is full of qemu-iotests--specific details. Separating it
from "common" does not make much sense anymore.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The variable is almost unused, and one of the two uses is actually
uninitialized.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The variable is used in "common" but defined only after the file
is sourced.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Split "check" parts from tests part.
For the directory setup, the actual computation of directories goes
in "check", while the sanity checks go in the tests.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
It only provides functions used by the test programs.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
These are never used by "check", with one exception that does not need
$QEMU_OPTIONS. Keep them in common.rc, which will be soon included only
by the tests.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Instead of ./check failing when a binary is missing, we try each test
case now and each one fails with tons of test case diffs. Also, all the
variables were initialized by "check" prior to "common" being sourced,
and then (uselessly) checked for emptiness again in "check".
Centralize the search for programs in "common" (which will soon be
one with "check"), including the "realpath" invocation which can be done
just once in "check" rather than in the tests.
For qnio_server, move the detection to "common", simplifying
set_prog_path to stop handling the unused second argument, and
embedding the "realpath" pass.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Some functions in common.rc are never used by the tests. Move
them out of that file and into common, which is already included
only by "check".
Code that actually *is* common to "check" and tests can be placed in
common.config.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This includes shell function, shell variables and command line options
(randomize.awk does not exist).
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The condition of the for-loop makes sure that b is always smaller
than s->blocks, so the "if (b >= s->blocks)" statement is completely
superfluous here.
Buglink: https://bugs.launchpad.net/qemu/+bug/1715007
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Now that all callers are using byte-based interfaces, there's no
reason for our internal hbitmap to remain with sector-based
granularity. It also simplifies our internal scaling, since we
already know that hbitmap widens requests out to granularity
boundaries.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Both callers already had bytes available, but were scaling to
sectors. Move the scaling to internal code. In the case of
bdrv_aligned_pwritev(), we are now passing the exact offset
rather than a rounded sector-aligned value, but that's okay
as long as dirty bitmap widens start/bytes to granularity
boundaries.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Now that we have adjusted the majority of the calls this function
makes to be byte-based, it is easier to read the code if it makes
passes over the image using bytes rather than sectors.
iotests 165 was rather weak - on a default 64k-cluster image, where
bitmap granularity also defaults to 64k bytes, a single cluster of
the bitmap table thus covers (64*1024*8) bits which each cover 64k
bytes, or 32G of image space. But the test only uses a 1G image,
so it cannot trigger any more than one loop of the code in
store_bitmap_data(); and it was writing to the first cluster. In
order to test that we are properly aligning which portions of the
bitmap are being written to the file, we really want to test a case
where the first dirty bit returned by bdrv_dirty_iter_next() is not
aligned to the start of a cluster, which we can do by modifying the
test to write data that doesn't happen to fall in the first cluster
of the image.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Now that we have adjusted the majority of the calls this function
makes to be byte-based, it is easier to read the code if it makes
passes over the image using bytes rather than sectors.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This is new code, but it is easier to read if it makes passes over
the image using bytes rather than sectors (and will get easier in
the future when bdrv_get_block_status is converted to byte-based).
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Now that we have adjusted the majority of the calls this function
makes to be byte-based, it is easier to read the code if it makes
passes over the image using bytes rather than sectors.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Some of the callers were already scaling bytes to sectors; others
can be easily converted to pass byte offsets, all in our shift
towards a consistent byte interface everywhere. Making the change
will also make it easier to write the hold-out callers to use byte
rather than sectors for their iterations; it also makes it easier
for a future dirty-bitmap patch to offload scaling over to the
internal hbitmap. Although all callers happen to pass
sector-aligned values, make the internal scaling robust to any
sub-sector requests.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Half the callers were already scaling bytes to sectors; the other
half can eventually be simplified to use byte iteration. Both
callers were already using the result as a bool, so make that
explicit. Making the change also makes it easier for a future
dirty-bitmap patch to offload scaling over to the internal hbitmap.
Remember, asking whether a byte is dirty is effectively asking
whether the entire granularity containing the byte is dirty, since
we only track dirtiness by granularity.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>