The current implementation initializes the stack pointer of AVR devices
to 0. Although older AVR devices used to be like that, newer ones set
it to RAMEND.
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1525
Signed-off-by: Gihun Nam <gihun.nam@outlook.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <PH0P222MB0010877445B594724D40C924DEBDA@PH0P222MB0010.NAMP222.PROD.OUTLOOK.COM>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
This device is a function of VIA south bridge and should allow setting
interrupt routing within that chip. This is implemented in
via_isa_set_irq().
Fixes: eb604411a7
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-ID: <5329840e4be6dd8ae143d07cbfe61d8d2d106654.1701035944.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
The chip has 4 pins (called PIRQA-D in VT82C686B and PINTA-D in
VT8231) that are meant to be connected to PCI IRQ lines and allow
routing PCI interrupts to the ISA PIC. Route these in
via_isa_set_irq() to make it possible to share them with internal
functions that can also be routed to the same ISA IRQs.
Fixes: 2fdadd02e6
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-ID: <8c4513d8b78fac40e6d4e65a0a4b3a7f2f278a4b.1701035944.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
This device is part of a superio/ISA bridge chip and IRQs from it are
routed to an ISA interrupt. Use via_isa_set_irq() function to implement
this in a vt82c686-uhci-pci specific irq handler.
This reverts commit 422a6e8075.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-ID: <ed5cdeaba7cf01eebdaa35f84c63427f4d8876b1.1701035944.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
The VIA integrated south bridge chips combine several functions and
allow routing their interrupts to any of the ISA IRQs also allowing
multiple sources to share the same ISA IRQ. E.g. pegasos2 firmware
configures everything to use IRQ 9 but amigaone routes them to
separate ISA IRQs so the current simplified routing does not work.
Bring back via_isa_set_irq() and change it to take the component that
wants to change an IRQ and keep track of interrupt status of each
source separately and do the mapping to ISA IRQ within the ISA bridge.
This may not handle cases when an ISA IRQ is controlled by devices
directly, not going through via_isa_set_irq() such as serial, parallel
or keyboard but these IRQs being conventionally fixed are not likely
to be change by guests or share with other devices so this does not
cause a problem in practice.
This reverts commit 4e5a20b6da.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-ID: <1c3902d4166234bef0a476026441eaac3dd6cda5.1701035944.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
ELF_LOAD_FAILED is one of many negative return codes we can have. Lets
treat any positive size_t as a success for loading.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20231120150833.2552739-10-alex.bennee@linaro.org>
If you check the manual of SiFive E310 (https://cdn.sparkfun.com/assets/7/f/0/2/7/fe310-g002-manual-v19p05.pdf),
you can see in Figure 1 that the CLINT is connected to the real time clock, which also feeds the AON peripheral (they share the same clock).
In page 43, the docs also say that the timer registers of the CLINT count ticks from the rtcclk.
I am currently playing with bare metal applications both in QEMU and a physical SiFive E310 board and
I confirm that the CLINT clock in the physical board runs at 32.768 kHz.
In QEMU, the same app produces a completely different outcome, as sometimes a new CLINT interrupt is triggered before finishing other tasks.
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1978
Signed-off-by: Rom\ufffd\ufffdn C\ufffd\ufffdrdenas <rcardenas.rod@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Message-ID: <20231117082840.55705-1-rcardenas.rod@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Commit 49554856f0 fixed a problem, where TPM devices were not appearing
in the FDT, by delaying the FDT creation up until virt_machine_done().
This create a side effect (see gitlab #1925) - devices that need access
to the '/chosen' FDT node during realize() stopped working because, at
that point, we don't have a FDT.
This happens because our FDT creation is monolithic, but it doesn't need
to be. We can add the needed FDT components for realize() time and, at
the same time, do another FDT round where we account for dynamic sysbus
devices. In other words, the problem fixed by 49554856f0 could also be
fixed by postponing only create_fdt_sockets() and its dependencies,
leaving everything else from create_fdt() to be done during init().
Split the FDT creation in two parts:
- create_fdt(), now moved back to virt_machine_init(), will create FDT
nodes that doesn't depend on additional (dynamic) devices from the
sysbus;
- a new finalize_fdt() step is added, where create_fdt_sockets() and
friends is executed, accounting for the dynamic sysbus devices that
were added during realize().
This will make both use cases happy: TPM devices are still working as
intended, and devices such as 'guest-loader' have a FDT to work on
during realize().
Fixes: 49554856f0 ("riscv: Generate devicetree only after machine initialization is complete")
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1925
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20231110172559.73209-1-dbarboza@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Allow the VIA IDE controller to switch between both legacy and native modes by
calling pci_ide_update_mode() to reconfigure the device whenever PCI_CLASS_PROG
is updated.
This patch moves the initial setting of PCI_CLASS_PROG from via_ide_realize() to
via_ide_reset(), and removes the direct setting of PCI_INTERRUPT_PIN during PCI
bus reset since this is now managed by pci_ide_update_mode(). This ensures that
the device configuration is always consistent with respect to the currently
selected mode.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-ID: <20231116103355.588580-5-mark.cave-ayland@ilande.co.uk>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The via-ide device currently attempts to set the default BAR addresses to the
values shown in the datasheet, but this doesn't work for 2 reasons: firstly
BARS 1-4 do not set the bottom 2 bits to PCI_BASE_ADDRESS_SPACE_IO, and
secondly the initial PCI bus reset clears the values of all PCI device BARs
after the device itself has been reset.
Remove the setting of the default BAR addresses from via_ide_reset() to ensure
there is no doubt that these values are never exposed to the guest.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-ID: <20231116103355.588580-4-mark.cave-ayland@ilande.co.uk>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This function reads the value of the PCI_CLASS_PROG register for PCI IDE
controllers and configures the PCI BARs and/or IDE ioports accordingly.
In the case where we switch to legacy mode, the PCI BARs are set to return zero
(as suggested in the "PCI IDE Controller" specification), the legacy IDE ioports
are enabled, and the PCI interrupt pin cleared to indicate legacy IRQ routing.
Conversely when we switch to native mode, the legacy IDE ioports are disabled
and the PCI interrupt pin set to indicate native IRQ routing. The contents of
the PCI BARs are unspecified, but this is not an issue since if a PCI IDE
controller has been switched to native mode then its BARs will need to be
programmed.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-ID: <20231116103355.588580-3-mark.cave-ayland@ilande.co.uk>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
These definitions are present in ioport.c which is currently only available when
CONFIG_IDE_ISA is enabled. Move them to the IDE core so that they can be made
available to PCI IDE controllers that support switching to legacy mode.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-ID: <20231116103355.588580-2-mark.cave-ayland@ilande.co.uk>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Legacy software contains a standard mechanism for generating a reset to a
Serial ATA device - setting the SRST (software reset) bit in the Device
Control register.
Serial ATA has a more robust mechanism called COMRESET, also referred to
as port reset. A port reset is the preferred mechanism for error
recovery and should be used in place of software reset.
Commit e2a5d9b3d9 ("hw/ide/ahci: simplify and document PxCI handling")
improved the handling of PxCI, such that PxCI gets cleared after handling
a non-NCQ, or NCQ command (instead of incorrectly clearing PxCI after
receiving anything - even a FIS that failed to parse, which should NOT
clear PxCI, so that you can see which command slot that caused an error).
However, simply clearing PxCI after a non-NCQ, or NCQ command, is not
enough, we also need to clear PxCI when receiving a SRST in the Device
Control register.
A legacy software reset is performed by the host sending two H2D FISes,
the first H2D FIS asserts SRST, and the second H2D FIS deasserts SRST.
The first H2D FIS will not get a D2H reply, and requires the FIS to have
the C bit set to one, such that the HBA itself will clear the bit in PxCI.
The second H2D FIS will get a D2H reply once the diagnostic is completed.
The clearing of the bit in PxCI for this command should ideally be done
in ahci_init_d2h() (if it was a legacy software reset that caused the
reset (a COMRESET does not use a command slot)). However, since the reset
value for PxCI is 0, modify ahci_reset_port() to actually clear PxCI to 0,
that way we can avoid complex logic in ahci_init_d2h().
This fixes an issue for FreeBSD where the device would fail to reset.
The problem was not noticed in Linux, because Linux uses a COMRESET
instead of a legacy software reset by default.
Fixes: e2a5d9b3d9 ("hw/ide/ahci: simplify and document PxCI handling")
Reported-by: Marcin Juszkiewicz <marcin.juszkiewicz@linaro.org>
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Message-ID: <20231108222657.117984-1-nks@flawful.org>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Tested-by: Marcin Juszkiewicz <marcin.juszkiewicz@linaro.org>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Coverity couldn't see that nr_existing was always going to be zero when
qemu_xen_xs_directory() returned NULL in the ENOENT case (CID 1523906).
Perhaps more to the point, neither could Peter at first glance. Improve
the code to hopefully make it clearer to Coverity and human reviewers
alike.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Paul Durrant <paul@xen.org>
* enable FEAT_RNG on Neoverse-N2
* hw/intc/arm_gicv3: ICC_PMR_EL1 high bits should be RAZ
* Fix SME FMOPA (16-bit), BFMOPA
* hw/core/machine: Constify MachineClass::valid_cpu_types[]
* stm32f* machines: Report error when user asks for wrong CPU type
* hw/arm/fsl-imx: Do not ignore Error argument
-----BEGIN PGP SIGNATURE-----
iQJNBAABCAA3FiEE4aXFk81BneKOgxXPPCUl7RQ2DN4FAmVchLYZHHBldGVyLm1h
eWRlbGxAbGluYXJvLm9yZwAKCRA8JSXtFDYM3kHMD/47tKxzrsXc6+V9esRQGi2H
1hAgLBwglEdxLXokF+Di41sh/fvK7wYVXO/hiWlq+9h3kG3D/u1N5r1TdMPMUb9j
4Sg3rOejn7nzkxVZ6MZ/K/1j84C9bfrt4sboVHZVRvWuvbiyuTuivEr4IqLYO4x3
AIwhFMQ5gbNrmClZh/DBxj0keO13cp63Fg2JSSICdi+1Dw9rRXTyhJloMu1omeqc
k/BXzjSeNXpLSMyGWBR3uaPcJBaGC1xnz3Z1V7fUY1EYD2Cu1oo5lEZ9aNO5t30d
XW/qVGLa3b1Cb7WuEO247RnU3N2oZotozjFtdj/8IQoYWspM9RHyipEimUlegVdO
3fpu8QGsN1ljNiwjdk0i6OwS7SGxcPtteFOaqEf/Yogj4EOKTn/Rx5TT4vJ5DhmI
2w/9J15JWDIE1paNwecuFWbxCOOzSsOtSxzuyLSZDU3GlNfJ4zoF6YboROLYfejy
NXZABFhGd/0ykX7r0VY1GGYXUQ+akv6q+VDmVZCP9gMiRUiqmFPwMLMLlcuHb8G5
8UztN5SvOG2EYXj28Zx0BnGCNiGdI15rWMb0veqAtbnn3yEdltW3O475BAhZ0PB7
OVpLWnXwmWURm/BGlwb1PH5s3kgWgzOebcBgcnCftwFQ8EedQAQDA5FmT+nK5SfV
VoOf89PngTubU6B3BOfeBw==
=thIa
-----END PGP SIGNATURE-----
Merge tag 'pull-target-arm-20231121' of https://git.linaro.org/people/pmaydell/qemu-arm into staging
target-arm queue:
* enable FEAT_RNG on Neoverse-N2
* hw/intc/arm_gicv3: ICC_PMR_EL1 high bits should be RAZ
* Fix SME FMOPA (16-bit), BFMOPA
* hw/core/machine: Constify MachineClass::valid_cpu_types[]
* stm32f* machines: Report error when user asks for wrong CPU type
* hw/arm/fsl-imx: Do not ignore Error argument
# -----BEGIN PGP SIGNATURE-----
#
# iQJNBAABCAA3FiEE4aXFk81BneKOgxXPPCUl7RQ2DN4FAmVchLYZHHBldGVyLm1h
# eWRlbGxAbGluYXJvLm9yZwAKCRA8JSXtFDYM3kHMD/47tKxzrsXc6+V9esRQGi2H
# 1hAgLBwglEdxLXokF+Di41sh/fvK7wYVXO/hiWlq+9h3kG3D/u1N5r1TdMPMUb9j
# 4Sg3rOejn7nzkxVZ6MZ/K/1j84C9bfrt4sboVHZVRvWuvbiyuTuivEr4IqLYO4x3
# AIwhFMQ5gbNrmClZh/DBxj0keO13cp63Fg2JSSICdi+1Dw9rRXTyhJloMu1omeqc
# k/BXzjSeNXpLSMyGWBR3uaPcJBaGC1xnz3Z1V7fUY1EYD2Cu1oo5lEZ9aNO5t30d
# XW/qVGLa3b1Cb7WuEO247RnU3N2oZotozjFtdj/8IQoYWspM9RHyipEimUlegVdO
# 3fpu8QGsN1ljNiwjdk0i6OwS7SGxcPtteFOaqEf/Yogj4EOKTn/Rx5TT4vJ5DhmI
# 2w/9J15JWDIE1paNwecuFWbxCOOzSsOtSxzuyLSZDU3GlNfJ4zoF6YboROLYfejy
# NXZABFhGd/0ykX7r0VY1GGYXUQ+akv6q+VDmVZCP9gMiRUiqmFPwMLMLlcuHb8G5
# 8UztN5SvOG2EYXj28Zx0BnGCNiGdI15rWMb0veqAtbnn3yEdltW3O475BAhZ0PB7
# OVpLWnXwmWURm/BGlwb1PH5s3kgWgzOebcBgcnCftwFQ8EedQAQDA5FmT+nK5SfV
# VoOf89PngTubU6B3BOfeBw==
# =thIa
# -----END PGP SIGNATURE-----
# gpg: Signature made Tue 21 Nov 2023 05:21:42 EST
# gpg: using RSA key E1A5C593CD419DE28E8315CF3C2525ED14360CDE
# gpg: issuer "peter.maydell@linaro.org"
# gpg: Good signature from "Peter Maydell <peter.maydell@linaro.org>" [full]
# gpg: aka "Peter Maydell <pmaydell@gmail.com>" [full]
# gpg: aka "Peter Maydell <pmaydell@chiark.greenend.org.uk>" [full]
# gpg: aka "Peter Maydell <peter@archaic.org.uk>" [unknown]
# Primary key fingerprint: E1A5 C593 CD41 9DE2 8E83 15CF 3C25 25ED 1436 0CDE
* tag 'pull-target-arm-20231121' of https://git.linaro.org/people/pmaydell/qemu-arm:
hw/arm/fsl-imx: Do not ignore Error argument
hw/arm/stm32f100: Report error when incorrect CPU is used
hw/arm/stm32f205: Report error when incorrect CPU is used
hw/arm/stm32f405: Report error when incorrect CPU is used
hw/core/machine: Constify MachineClass::valid_cpu_types[]
target/arm: Fix SME FMOPA (16-bit), BFMOPA
hw/intc/arm_gicv3: ICC_PMR_EL1 high bits should be RAZ
target/arm: enable FEAT_RNG on Neoverse-N2
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Recently MemReentrancyGuard was added to DeviceState to record that the
device is engaging in I/O. The network device backend needs to update it
when delivering a packet to a device.
In preparation for such a change, add MemReentrancyGuard * as a
parameter of qemu_new_nic().
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Alexander Bulekov <alxndr@bu.edu>
Signed-off-by: Jason Wang <jasowang@redhat.com>
The PNV I2C Controller was clearing the status register
after a reset without repopulating the "upper threshold
for I2C ports", "Command Complete" and the SCL/SDA input
level fields.
Fixed this for resets caused by a system reset as well
as from writing to the "Immediate Reset" register.
Fixes: 263b81ee15 ("ppc/pnv: Add an I2C controller model")
Signed-off-by: Glenn Miles <milesg@linux.vnet.ibm.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The PNV I2C engines for power9 and power10 were being assigned a base
XSCOM address that was off by one I2C engine's address range such
that engine 0 had engine 1's address and so on. The xscom address
assignment was being based on the device tree engine numbering, which
starts at 1. Rather than changing the device tree numbering to start
with 0, the addressing was changed to be based on the existing device
tree numbers minus one.
Fixes: 1ceda19c28 ("ppc/pnv: Connect PNV I2C controller to powernv10)
Signed-off-by: Glenn Miles <milesg@linux.vnet.ibm.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Coverity warns that "i2c_bus_busy(i2c->busses[i]) << i" might overflow
because the expression is evaluated using 32-bit arithmetic and then
used in a context expecting a uint64_t.
While we are at it, introduce a PNV_I2C_MAX_BUSSES constant and check
the number of busses at realize time.
Fixes: Coverity CID 1523918
Cc: Glenn Miles <milesg@linux.vnet.ibm.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Glenn Miles <milesg@linux.vnet.ibm.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Both i.MX25 and i.MX6 SoC models ignore the Error argument when
setting the PHY number. Pick &error_abort which is the error
used by the i.MX7 SoC (see commit 1f7197deb0 "ability to change
the FEC PHY on i.MX7 processor").
Fixes: 74c1330582 ("ability to change the FEC PHY on i.MX25 processor")
Fixes: a9c167a3c4 ("ability to change the FEC PHY on i.MX6 processor")
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20231120115116.76858-1-philmd@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The 'stm32vldiscovery' machine ignores the CPU type requested by
the command line. This might confuse users, since the following
will create a machine with a Cortex-M3 CPU:
$ qemu-system-aarch64 -M stm32vldiscovery -cpu neoverse-n1
Set the MachineClass::valid_cpu_types field (introduced in commit
c9cf636d48 "machine: Add a valid_cpu_types property").
Remove the now unused MachineClass::default_cpu_type field.
We now get:
$ qemu-system-aarch64 -M stm32vldiscovery -cpu neoverse-n1
qemu-system-aarch64: Invalid CPU type: neoverse-n1-arm-cpu
The valid types are: cortex-m3-arm-cpu
Since the SoC family can only use Cortex-M3 CPUs, hard-code the
CPU type name at the SoC level, removing the QOM property
entirely.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Gavin Shan <gshan@redhat.com>
Message-id: 20231117071704.35040-5-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The 'netduino2' machine ignores the CPU type requested by the
command line. This might confuse users, since the following will
create a machine with a Cortex-M3 CPU:
$ qemu-system-arm -M netduino2 -cpu cortex-a9
Set the MachineClass::valid_cpu_types field (introduced in commit
c9cf636d48 "machine: Add a valid_cpu_types property").
Remove the now unused MachineClass::default_cpu_type field.
We now get:
$ qemu-system-arm -M netduino2 -cpu cortex-a9
qemu-system-arm: Invalid CPU type: cortex-a9-arm-cpu
The valid types are: cortex-m3-arm-cpu
Since the SoC family can only use Cortex-M3 CPUs, hard-code the
CPU type name at the SoC level, removing the QOM property
entirely.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Gavin Shan <gshan@redhat.com>
Message-id: 20231117071704.35040-4-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Both 'netduinoplus2' and 'olimex-stm32-h405' machines ignore the
CPU type requested by the command line. This might confuse users,
since the following will create a machine with a Cortex-M4 CPU:
$ qemu-system-aarch64 -M netduinoplus2 -cpu cortex-r5f
Set the MachineClass::valid_cpu_types field (introduced in commit
c9cf636d48 "machine: Add a valid_cpu_types property").
Remove the now unused MachineClass::default_cpu_type field.
We now get:
$ qemu-system-aarch64 -M netduinoplus2 -cpu cortex-r5f
qemu-system-aarch64: Invalid CPU type: cortex-r5f-arm-cpu
The valid types are: cortex-m4-arm-cpu
Since the SoC family can only use Cortex-M4 CPUs, hard-code the
CPU type name at the SoC level, removing the QOM property
entirely.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Gavin Shan <gshan@redhat.com>
Message-id: 20231117071704.35040-3-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Constify MachineClass::valid_cpu_types[i], as suggested by Richard
Henderson.
Suggested-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Gavin Shan <gshan@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20231117071704.35040-2-philmd@linaro.org
[PMD: Constify HPPA machines,
restrict valid_cpu_types to machine_class_init() handlers]
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The ICC_PMR_ELx and ICV_PMR_ELx bit masks returned from
ic{c,v}_fullprio_mask should technically also remove any
bit above 7 as these are marked reserved (read 0) and should
therefore should not be written as anything other than 0.
This was noted during a run of a proprietary test system and
discused on the mailing list [1] and initially thought not to
be an issue due to RES0 being technically allowed to be
written to and read back as long as the implementation does
not use the RES0 bits. It is very possible that the values
are used in comparison without masking, as pointed out by
Peter in [2], if (cs->hppi.prio >= cs->icc_pmr_el1) may well
do the wrong thing.
Masking these values in ic{c,v}_fullprio_mask() should fix
this and prevent any future problems with playing with the
values.
[1]: https://lists.nongnu.org/archive/html/qemu-arm/2023-11/msg00607.html
[2]: https://lists.nongnu.org/archive/html/qemu-arm/2023-11/msg00737.html
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Message-id: 20231116172818.792364-1-ben.dooks@codethink.co.uk
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When dynamic-reconfiguration is off, hot plug / unplug can fail with
"Bus 'spapr-pci-host-bridge' does not support hotplugging".
spapr-pci-host-bridge is a device, not a bus. Report the name of the
bus it provides instead: 'pci.0'.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-ID: <20231031111059.3407803-2-armbru@redhat.com>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Fixes: c755c943aa "hw/net/cadence_gem: use REG32 macro for register definitions"
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Luc Michel <luc.michel@amd.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Fixes: 6c1b28e9e4 "memory-device: Support empty memory devices"
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Fixes: 388d6b574e "hw/cxl: Use switch statements for read and write of cachemem registers"
Fixes: 3314efd276 "hw/cxl/mbox: Add Physical Switch Identify command."
Fixes: 004e3a93b8 "hw/cxl: Add tunneled command support to mailbox for switch cci."
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Fixes: eb9ad377bb "virtio-sound: handle control messages and streams"
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Reviewed-by: Stefan Weil <sw@weilnetz.de>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Aspeed watchdog doesn't use anything from the System Control Unit.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The new SeaBIOS-hppa version 12 includes the necessary fixes to
support emulated PA2.0 CPUs and which allows starting 64-bit Linux
kernels in the guest.
To boot a 64-bit machine use the "-machine C3700" qemu option.
Signed-off-by: Helge Deller <deller@gmx.de>
Acked-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Something appears to be off between the 64-bit CPU, the 32-bit PDC
(SeaBIOS-hppa firmware), and the 64-bit kernel in addressing the
power button address in high-mapped firmware memory.
Use a 32-bit value at PAGE0->pad0[4] instead.
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Apply the "32-bit PCI addressing on 40-bit Runway" as the default
iommu transformation. This allows PCI devices to dma PDC memory.
Signed-off-by: Helge Deller <deller@gmx.de>
Acked-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
When calling trace_vmware_verify_rect_greater_than_bound() replace
"y" with "h" and y with h
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 02218aedb1 ("hw/display/vmware_vga: replace fprintf calls with trace events")
Signed-off-by: Alexandra Diupina <adiupina@astralinux.ru>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-ID: <20231110174104.13280-1-adiupina@astralinux.ru>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Since commit 9036e917f8 ("{include/}hw/arm: refactor virt PPI logic"),
GIC maintenance IRQ registration fails on arm64:
[ 0.979743] kvm [1]: Cannot register interrupt 9
That commit re-defined VIRTUAL_PMU_IRQ to be a INTID but missed a case
where the maintenance IRQ is actually referred by its PPI index. Just
like commit fa68ecb330 ("hw/arm/virt: fix PMU IRQ registration"), use
INITID_TO_PPI(). A search of "GIC_FDT_IRQ_TYPE_PPI" indicates that there
shouldn't be more similar issues.
Fixes: 9036e917f8 ("{include/}hw/arm: refactor virt PPI logic")
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Message-id: 20231110090557.3219206-2-jean-philippe@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* Two small s390x PCI fixes
* Update MAINTAINERS file with more entries
* Fix NetBSD VM test
* Clean up some bad wordings
-----BEGIN PGP SIGNATURE-----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=+2rp
-----END PGP SIGNATURE-----
Merge tag 'pull-request-2023-11-13' of https://gitlab.com/thuth/qemu into staging
* Fix compilation with Clang 17 on s390x hosts
* Two small s390x PCI fixes
* Update MAINTAINERS file with more entries
* Fix NetBSD VM test
* Clean up some bad wordings
# -----BEGIN PGP SIGNATURE-----
#
# iQJFBAABCAAvFiEEJ7iIR+7gJQEY8+q5LtnXdP5wLbUFAmVSAoIRHHRodXRoQHJl
# ZGhhdC5jb20ACgkQLtnXdP5wLbVXBg//VVZS5CXEfOFV91I1kqQnLCvgwmuAyqEg
# PI2/HBxuhzeBx+F1t7uR0n15tUPi1zkFFBOpyBDBubvWcp4vGvFwLQoiBCUvNzBA
# +b1vMySP+K0OO1X5yT3cFHXF9q0o0V5WADwemf5RglIPjlTOIiz9qhD4EYqd2QHC
# EUd9Y45DP4Y0V5raHLjY990f/zr3PuSAB6MASFTUnKdgGkRqonLWdLDdIZNDrZuL
# oGwx1ALXgBOMV3yNyQx9jZBT24git/ai1vd9AU/d3JRKDPsd+4vC39+PTI9NH4h6
# oQglvo399f64cir1f1JJ3MN4ZtwXZpwUkjeTMcR9XZxk7GibU7P2arG5M3TERdmE
# VLqylYsnbJojWOeCH+TViJapRhg1CzUveVlQofr7GHvf2N3oy3BrKaV715gauEyW
# zpjbhSPpIQu9WFXt8+tSquqbvpAP/VlLrOV73D4LzJ7WdTa9CHmSek8D0zoRQDZR
# 8OixrgoBKS+pmBDmTve5gFsIKhZIz9CrmaAKKYdskC8blENxCng8LOFp7sg2PK3M
# U0lWYoDS7qZ85761Bl+QaBdFocdahQqkO/LUQuhoSt2OvA1EGAz2FdVSKkmPDdSS
# P/homr4hOXIqJFSsZj0YNUTIXsXwLBvKjvcJPAWYgbXZhim0LtPQTQO3+ignwGyu
# RXjaVkvkf/s=
# =+2rp
# -----END PGP SIGNATURE-----
# gpg: Signature made Mon 13 Nov 2023 06:03:30 EST
# gpg: using RSA key 27B88847EEE0250118F3EAB92ED9D774FE702DB5
# gpg: issuer "thuth@redhat.com"
# gpg: Good signature from "Thomas Huth <th.huth@gmx.de>" [full]
# gpg: aka "Thomas Huth <thuth@redhat.com>" [full]
# gpg: aka "Thomas Huth <huth@tuxfamily.org>" [full]
# gpg: aka "Thomas Huth <th.huth@posteo.de>" [unknown]
# Primary key fingerprint: 27B8 8847 EEE0 2501 18F3 EAB9 2ED9 D774 FE70 2DB5
* tag 'pull-request-2023-11-13' of https://gitlab.com/thuth/qemu:
hw/audio/es1370: Clean up comment
tests/tsan: Rename the file with the entries that should be ignored
test-resv-mem: Fix CID 1523911
tests/vm/netbsd: Use Python v3.11
MAINTAINERS: Add a general architecture section for x86
MAINTAINERS: Extend the Stellaris section
MAINTAINERS: Add hw/display/sii9022.c to the Versatile Express section
MAINTAINERS: Add hw/input/ads7846.c to the PXA2XX section
MAINTAINERS: Add include/hw/input/pl050.h to the PrimeCell/CMSDK section
s390x/pci: only limit DMA aperture if vfio DMA limit reported
s390x/pci: bypass vfio DMA counting when using cdev
host/include/generic/host/atomic128: Fix compilation problem with Clang 17
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Replace a sweary comment with one that's a bit more helpful to
future readers of the code.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Volker Rümelin <vr_qemu@t-online.de>
Message-ID: <20231110164318.2197569-1-peter.maydell@linaro.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
If the host kernel lacks vfio DMA limit reporting, do not attempt
to shrink the guest DMA aperture.
Fixes: df202e3ff3 ("s390x/pci: shrink DMA aperture to be bound by vfio DMA limit")
Signed-off-by: Matthew Rosato <mjrosato@linux.ibm.com>
Message-ID: <20231110175108.465851-3-mjrosato@linux.ibm.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
The current code assumes that there is always a vfio group, but
that's no longer guaranteed with the iommufd backend when using
cdev. In this case, we don't need to track the vfio dma limit
anyway.
Signed-off-by: Matthew Rosato <mjrosato@linux.ibm.com>
Message-ID: <20231110175108.465851-2-mjrosato@linux.ibm.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
