All QMP commands use the "new" handler interface (mhandler.cmd_new).
Most HMP commands still use the traditional interface (mhandler.cmd),
but a few use the "new" one. Complicates handle_user_command() for no
gain, so I'm converting these to the traditional interface.
pcie_aer_inject_error's implementation is split into the
hmp_pcie_aer_inject_error() and pcie_aer_inject_error_print(). The
former is a peculiar crossbreed between HMP and QMP handler. On
success, it works like a QMP handler: store QDict through ret_data
parameter, return 0. Printing the QDict is left to
pcie_aer_inject_error_print(). On failure, it works more like an HMP
handler: print error to monitor, return negative number.
To convert to the traditional interface, turn
pcie_aer_inject_error_print() into a command handler wrapping around
hmp_pcie_aer_inject_error(). By convention, this command handler
should be called hmp_pcie_aer_inject_error(), so rename the existing
hmp_pcie_aer_inject_error() to do_pcie_aer_inject_error().
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Luiz Capitulino <lcapitulino@redhat.com>
This commit was generated mechanically by coccinelle from the following
semantic patch:
@@
expression val;
@@
- (ffs(val) - 1)
+ ctz32(val)
The call sites have been audited to ensure the ffs(0) - 1 == -1 case
never occurs (due to input validation, asserts, etc). Therefore we
don't need to worry about the fact that ctz32(0) == 32.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1427124571-28598-5-git-send-email-stefanha@redhat.com
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Code comment says "table 6-2" but in fact it's is not a table, it is
"Figure 6-2" on page 479.
Cc: Chen Fan <chen.fan.fnst@cn.fujitsu.com>
Reported-by: Michael Tokarev <mjt@tls.msk.ru>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Error Status Register, so this patch fix a wrong definition
for PCI_ERR_COR_STATUS register with w1cmask type.
Signed-off-by: Chen Fan <chen.fan.fnst@cn.fujitsu.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Refer to "PCI Express Base Spec3.0", this comments can't
fit the description in spec, so we should fix them.
Signed-off-by: Chen Fan <chen.fan.fnst@cn.fujitsu.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
when specify TLP Prefix log as using pcie_aer_inject_error,
the TLP prefix log is always discarded. because the check
is incorrect, the End-End TLP Prefix Supported bit
(PCI_EXP_DEVCAP2_EETLPP) should be in Device Capabilities 2 Register.
Signed-off-by: Chen Fan <chen.fan.fnst@cn.fujitsu.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Some are called do_COMMAND() (old ones, usually), some hmp_COMMAND(),
and sometimes COMMAND pointlessly differs in spelling.
Normalize to hmp_COMMAND(), where COMMAND is exactly the command name
with '-' replaced by '_'.
Exceptions:
* do_device_add() and client_migrate_info() *not* renamed to
hmp_device_add(), hmp_client_migrate_info(), because they're also
QMP handlers. They still need to be converted to QAPI.
* do_memory_dump(), do_physical_memory_dump(), do_ioport_read(),
do_ioport_write() renamed do hmp_* instead of hmp_x(), hmp_xp(),
hmp_i(), hmp_o(), because those names are too cryptic for my taste.
* do_info_help() renamed to hmp_info_help() instead of hmp_info(),
because it only covers help.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
After previous Peter patch, they are redundant. This way we don't
assign them except when needed. Once there, there were lots of case
where the ".fields" indentation was wrong:
.fields = (VMStateField []) {
and
.fields = (VMStateField []) {
Change all the combinations to:
.fields = (VMStateField[]){
The biggest problem (appart from aesthetics) was that checkpatch complained
when we copy&pasted the code from one place to another.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Acked-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
4) CVE-2013-4529
hw/pci/pcie_aer.c pcie aer log can overrun the buffer if log_num is
too large
There are two issues in this file:
1. log_max from remote can be larger than on local
then buffer will overrun with data coming from state file.
2. log_num can be larger then we get data corruption
again with an overflow but not adversary controlled.
Fix both issues.
Reported-by: Anthony Liguori <anthony@codemonkey.ws>
Reported-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Replace the legacy cpu_to_be32wu() with stl_be_p().
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-id: 1383669517-25598-8-git-send-email-peter.maydell@linaro.org
Signed-off-by: Anthony Liguori <aliguori@amazon.com>
The fields hpev_intx and aer_intx were removed because
both AER and hot-plug events must use device's interrupt.
Assert/deassert interrupts using pci irq wrappers instead.
Signed-off-by: Marcel Apfelbaum <marcel.a@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
pci_find_domain() is used in a number of places where we want an id for a
whole PCI domain (i.e. the subtree under a PCI root bus). The trouble is
that many platforms may support multiple independent host bridges with no
hardware supplied notion of domain number.
This patch, therefore, replaces calls to pci_find_domain() with calls to
a new pci_root_bus_path() returning a string. The new call is implemented
in terms of a new callback in the host bridge class, so it can be defined
in some way that's well defined for the platform. When no callback is
available we fall back on the qbus name.
Most current uses of pci_find_domain() are for error or informational
messages, so the change in identifiers should be harmless. The exception
is pci_get_dev_path(), whose results form part of migration streams. To
maintain compatibility with old migration streams, the PIIX PCI host is
altered to always supply "0000" for this path, which matches the old domain
number (since the code didn't actually support domains other than 0).
For the pseries (spapr) PCI bridge we use a different platform-unique
identifier (pseries machines can routinely have dozens of PCI host
bridges). Theoretically that breaks migration streams, but given that we
don't yet have migration support for pseries, it doesn't matter.
Any other machines that have working migration support including PCI
devices will need to be updated to maintain migration stream compatibility.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Currently pci_find_domain() performs two functions - it locates the PCI
root bus above the given bus, then looks up that root bus's domain number.
This patch adds a helper function to perform the first task, finding the
root bus for a given PCI device. This is then used in pci_find_domain().
This changes pci_find_domain()'s signature slightly, taking a PCIDevice
instead of a PCIBus - since all callers passed something of the form
dev->bus, this simplifies things slightly.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
There are lots of external users of pci_internals.h,
apparently making it an internal interface only didn't
work out. Let's stop pretending it's an internal header.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Include dependencies from pci core using the correct path.
This is required now that it's in the separate directory.
Need to check whether they can be minimized, for now,
keep the code as is.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Markus Armbruster
Stefan Hajnoczi
Michael S. Tsirkin
Chen Fan
Juan Quintela
Peter Maydell
Marcel Apfelbaum
David Gibson
Paolo Bonzini