And at the same time make IPTE SMP aware.
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Message-Id: <20170531220129.27724-4-aurelien@aurel32.net>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Previously, helper_ex would construct the insn and then implement
the insn via direct calls other helpers. This was sufficient to
boot Linux but that is all.
It is easy enough to go the whole nine yards by stashing state for
EXECUTE within the cpu, and then rely on a new TB to be created
that properly and completely interprets the insn.
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Richard Henderson <rth@twiddle.net>
This split will be required for implementing EXECUTE properly.
Do this now as a separate step to aid comparison of before and
after TB listings.
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Use this saved value instead of recomputing from next_pc difference.
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Also provide the cross-cpu tlb flushing required by the PoO.
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Richard Henderson <rth@twiddle.net>
The PoO specifies that when R1==0, no ORing into the insn
loaded from storage takes place. Load a zero for this case.
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Richard Henderson <rth@twiddle.net>
(1) The OR of the low bits or R1 into INSN were not being done
consistently; it was forgotten along all but the SVC path.
(2) The setting of ILEN was wrong on SVC path for EXRL.
(3) The data load for ICM read too much.
Fix these by consolidating data load at the beginning, using
get_ilen to control the number of bytes loaded, and ORing in
the byte from R1. Use extract64 from the full aligned insn
to extract arguments.
Pass in ILEN rather than RET as the more natural way to give
the required data along the SVC path.
Modify ENV->CC_OP directly rather than include it in the
functional interface.
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Fix saving exception_index around mmu_translate; eliminate a dead store.
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Richard Henderson <rth@twiddle.net>
TEST BLOCK was likely once used to execute basic memory
tests, but nowadays it's just a (slow) way to clear a page.
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1495128400-23759-1-git-send-email-thuth@redhat.com>
Signed-off-by: Richard Henderson <rth@twiddle.net>
The SIGNAL PROCESSOR helper returns its value through the CC register.
set_cc_static should be called just after the helper.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Message-Id: <20170509082800.10756-3-aurelien@aurel32.net>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Eric Bischoff <ebischoff@nerim.net>
Message-Id: <20170228120134.7921-1-ebischoff@suse.com>
[rth: Combine the two via insn->data; free the address temps.]
Signed-off-by: Richard Henderson <rth@twiddle.net>
Linux arch/s390/kernel/head(64).S uses LPP instruction if it is
available in facilities list provided by stfl/stfle instruction.
This is the case of newer z/System generations and their qemu
definition.
The description of LPP is at
http://www-01.ibm.com/support/docview.wss?uid=isg26fcd1cc32246f4c8852574ce0044734a
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Miroslav Benes <mbenes@suse.cz>
Message-Id: <20170227085353.20787-1-mbenes@suse.cz>
Signed-off-by: Richard Henderson <rth@twiddle.net>
We've currently got 18 architectures in QEMU, and thus 18 target-xxx
folders in the root folder of the QEMU source tree. More architectures
(e.g. RISC-V, AVR) are likely to be included soon, too, so the main
folder of the QEMU sources slowly gets quite overcrowded with the
target-xxx folders.
To disburden the main folder a little bit, let's move the target-xxx
folders into a dedicated target/ folder, so that target-xxx/ simply
becomes target/xxx/ instead.
Acked-by: Laurent Vivier <laurent@vivier.eu> [m68k part]
Acked-by: Bastian Koppelmann <kbastian@mail.uni-paderborn.de> [tricore part]
Acked-by: Michael Walle <michael@walle.cc> [lm32 part]
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com> [s390x part]
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com> [s390x part]
Acked-by: Eduardo Habkost <ehabkost@redhat.com> [i386 part]
Acked-by: Artyom Tarasenko <atar4qemu@gmail.com> [sparc part]
Acked-by: Richard Henderson <rth@twiddle.net> [alpha part]
Acked-by: Max Filippov <jcmvbkbc@gmail.com> [xtensa part]
Reviewed-by: David Gibson <david@gibson.dropbear.id.au> [ppc part]
Acked-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com> [crisµblaze part]
Acked-by: Guan Xuetao <gxt@mprc.pku.edu.cn> [unicore32 part]
Signed-off-by: Thomas Huth <thuth@redhat.com>
Aurelien Jarno
Richard Henderson
Thomas Huth
Eric Bischoff
Miroslav Benes