The Aspeed I2C controller can operate in different transfer modes :
- Byte Buffer mode, using a dedicated register to transfer a
byte. This is what the model supports today.
- Pool Buffer mode, using an internal SRAM to transfer multiple
bytes in the same command sequence.
Each SoC has different SRAM characteristics. On the AST2400, 2048
bytes of SRAM are available at offset 0x800 of the controller AHB
window. The pool buffer can be configured from 1 to 256 bytes per bus.
On the AST2500, the SRAM is at offset 0x200 and the pool buffer is of
16 bytes per bus.
On the AST2600, the SRAM is at offset 0xC00 and the pool buffer is of
32 bytes per bus. It can be splitted in two for TX and RX but the
current model does not add support for it as it it unused by known
drivers.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Tested-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20191119141211.25716-2-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
exynos4210_gic_realize() prints the number of cpus into some temporary
buffers, but it only allows 3 bytes space for it. That's plenty:
existing machines will only ever set this value to EXYNOS4210_NCPUS
(2). But the compiler can't always figure that out, so some[*] gcc9
versions emit -Wformat-truncation warnings.
We can fix that by hinting the constraint to the compiler with a
suitably placed assert().
[*] The bizarre thing here, is that I've long gotten these warnings
compiling in a 32-bit x86 container as host - Fedora 30 with
gcc-9.2.1-1.fc30.i686 - but it compiles just fine on my normal
x86_64 host - Fedora 30 with and gcc-9.2.1-1.fc30.x86_64.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
[PMM: deleted stray blank line]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This is derived from cortex-m4 description, adding DP support and FPv5
instructions with the corresponding flags in isar and mvfr2.
Checked that it could successfully execute
vrinta.f32 s15, s15
while cortex-m4 emulation rejects it with "illegal instruction".
Signed-off-by: Christophe Lyon <christophe.lyon@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20191025090841.10299-1-christophe.lyon@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
- compat machines (also for other architectures)
- cleanups and fixes in reset handling
- fence off guest-set-time, as we have no hwclock
- fix some misuses of the error API
- further cleanups
-----BEGIN PGP SIGNATURE-----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=yt5l
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/cohuck/tags/s390x-20191214-2' into staging
First s390x update for 5.0:
- compat machines (also for other architectures)
- cleanups and fixes in reset handling
- fence off guest-set-time, as we have no hwclock
- fix some misuses of the error API
- further cleanups
# gpg: Signature made Sat 14 Dec 2019 09:33:17 GMT
# gpg: using RSA key C3D0D66DC3624FF6A8C018CEDECF6B93C6F02FAF
# gpg: issuer "cohuck@redhat.com"
# gpg: Good signature from "Cornelia Huck <conny@cornelia-huck.de>" [unknown]
# gpg: aka "Cornelia Huck <huckc@linux.vnet.ibm.com>" [full]
# gpg: aka "Cornelia Huck <cornelia.huck@de.ibm.com>" [full]
# gpg: aka "Cornelia Huck <cohuck@kernel.org>" [unknown]
# gpg: aka "Cornelia Huck <cohuck@redhat.com>" [unknown]
# Primary key fingerprint: C3D0 D66D C362 4FF6 A8C0 18CE DECF 6B93 C6F0 2FAF
* remotes/cohuck/tags/s390x-20191214-2:
qga: fence guest-set-time if hwclock not available
s390x/tcg: clear local interrupts on reset normal
s390x/cpumodel: Fix query-cpu-definitions error API violations
s390x/cpumodel: Fix query-cpu-model-FOO error API violations
s390x/cpumodel: Fix realize() error API violations
s390x/cpumodel: Fix feature property error API violations
s390x/event-facility: Fix realize() error API violations
s390x: Fix cpu normal reset ri clearing
s390x: kvm: Make kvm_sclp_service_call void
s390x: Beautify diag308 handling
s390x: Move clear reset
s390x: Move initial reset
s390x: Move reset normal to shared reset handler
s390x: Don't do a normal reset on the initial cpu
hw: add compat machines for 5.0
vfio-ccw: Fix error message
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Posix implementation of guest-set-time invokes hwclock to
set/retrieve the time to/from the hardware clock. If hwclock
is not available, the user is currently informed that "hwclock
failed to set hardware clock to system time", which is quite
misleading. This may happen e.g. on s390x, which has a different
timekeeping concept anyway.
Let's check for the availability of the hwclock command and
return QERR_UNSUPPORTED for guest-set-time if it is not available.
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Message-Id: <20191205115350.18713-1-cohuck@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
We neglected to clean up pending interrupts and emergency signals;
fix that.
Message-Id: <20191206135404.16051-1-cohuck@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
qmp_query_cpu_definitions() passes @errp to get_max_cpu_model(), then
frees any error it gets back. This effectively ignores errors.
Dereferencing @errp is wrong; see the big comment in error.h. Passing
@errp is also wrong, because it works only as long as @errp is neither
@error_fatal nor @error_abort. Introduced in commit 38cba1f4d8
"s390x: return unavailable features via query-cpu-definitions".
No caller actually passes such @errp values.
Fix anyway: simply pass NULL to get_max_cpu_model().
Cc: David Hildenbrand <david@redhat.com>
Cc: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Message-Id: <20191204093625.14836-16-armbru@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
cpu_model_from_info() is a helper for qmp_query_cpu_model_expansion(),
qmp_query_cpu_model_comparison(), qmp_query_cpu_model_baseline(). It
dereferences @errp when the visitor or the QOM setter fails. That's
wrong; see the big comment in error.h. Introduced in commit
137974cea3 's390x/cpumodel: implement QMP interface
"query-cpu-model-expansion"'.
Its three callers have the same issue. Introduced in commit
4e82ef0502 's390x/cpumodel: implement QMP interface
"query-cpu-model-comparison"' and commit f1a47d08ef 's390x/cpumodel:
implement QMP interface "query-cpu-model-baseline"'.
No caller actually passes null.
Fix anyway: splice in a local Error *err, and error_propagate().
Cc: David Hildenbrand <david@redhat.com>
Cc: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Message-Id: <20191204093625.14836-15-armbru@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
get_max_cpu_model() dereferences @errp when
kvm_s390_get_host_cpu_model() fails, apply_cpu_model() dereferences it
when kvm_s390_apply_cpu_model() fails, and s390_realize_cpu_model()
dereferences it when get_max_cpu_model() or check_compatibility()
fail. That's wrong; see the big comment in error.h. All three
introduced in commit 80560137cf "s390x/cpumodel: check and apply the
CPU model".
No caller actually passes null.
Fix anyway: splice in a local Error *err, and error_propagate().
Cc: David Hildenbrand <david@redhat.com>
Cc: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Message-Id: <20191204093625.14836-14-armbru@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
s390x-cpu property setters set_feature() and set_feature_group()
dereference @errp when the visitor fails. That's wrong; see the big
comment in error.h. Introduced in commit 0754f60429 "s390x/cpumodel:
expose features and feature groups as properties".
No caller actually passes null.
Fix anyway: splice in a local Error *err, and error_propagate().
Cc: David Hildenbrand <david@redhat.com>
Cc: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Message-Id: <20191204093625.14836-13-armbru@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
sclp_events_bus_realize() dereferences @errp when
object_property_set_bool() fails. That's wrong; see the big comment
in error.h. Introduced in commit f6102c329c "s390/sclp: rework sclp
event facility initialization + device realization".
No caller actually passes null.
Fix anyway: splice in a local Error *err, and error_propagate().
Cc: David Hildenbrand <david@redhat.com>
Cc: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Message-Id: <20191204093625.14836-12-armbru@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
As it turns out we need to clear the ri controls and PSW enablement
bit to be architecture compliant.
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Message-Id: <20191203132813.2734-4-frankja@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
It defaults to returning 0 anyway and that return value is not
necessary, as 0 is also the default rc that the caller would return.
While doing that we can simplify the logic a bit and return early if
we inject a PGM exception.
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20191129091713.4582-1-frankja@linux.ibm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Let's improve readability by:
* Using constants for the subcodes
* Moving parameter checking into a function
* Removing subcode > 6 check as the default case catches that
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Message-Id: <20191127175046.4911-6-frankja@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Let's also move the clear reset function into the reset handler.
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
Message-Id: <20191127175046.4911-5-frankja@linux.ibm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Let's move the intial reset into the reset handler and cleanup
afterwards.
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Message-Id: <20191128083723.11937-1-frankja@linux.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Let's start moving the cpu reset functions into a single function with
a switch/case, so we can later use fallthroughs and share more code
between resets.
This patch introduces the reset function by renaming cpu_reset().
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Message-Id: <20191127175046.4911-3-frankja@linux.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
The initiating cpu needs to be reset with an initial reset. While
doing a normal reset followed by a initial reset is not wrong per se,
the Ultravisor will only allow the correct reset to be performed.
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Message-Id: <20191127175046.4911-2-frankja@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Add 5.0 machine types for arm/i440fx/q35/s390x/spapr.
For i440fx and q35, unversioned cpu models are still translated
to -v1; I'll leave changing this (if desired) to the respective
maintainers.
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Message-Id: <20191112104811.30323-1-cohuck@redhat.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Add -object iothread documentation to the man page, including references
to the query-iothread QMP command and qom-set syntax for adjusting
adaptive polling parameters at run-time.
Reported-by: Zhenyu Ye <yezhenyu2@huawei.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 20191025122236.29815-1-stefanha@redhat.com
Message-Id: <20191025122236.29815-1-stefanha@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Virtio spec 1.1 (and earlier), 5.2.5.2 Driver Requirements: Device
Initialization:
"Devices SHOULD always offer VIRTIO_BLK_F_FLUSH, and MUST offer it if
they offer VIRTIO_BLK_F_CONFIG_WCE"
Currently F_CONFIG_WCE and F_WCE are not connected to each other.
Qemu will advertise F_CONFIG_WCE if config-wce argument is
set for virtio-blk device. And F_WCE is advertised only if
underlying block backend actually has it's caching enabled.
Fix this by advertising F_WCE if F_CONFIG_WCE is also advertised.
To preserve backwards compatibility with newer machine types make this
behaviour governed by "x-enable-wce-if-config-wce" virtio-blk-device
property and introduce hw_compat_4_2 with new property being off by
default for all machine types <= 4.2 (but don't introduce 4.3
machine type itself yet).
Signed-off-by: Evgeny Yakovlev <wrfsh@yandex-team.ru>
Message-Id: <1572978137-189218-1-git-send-email-wrfsh@yandex-team.ru>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
The following MSI-X vectors are required:
* VIRTIO Configuration Change
* hiprio virtqueue
* requests virtqueues
Fix the calculation to reserve enough MSI-X vectors. Otherwise guest
drivers fall back to a sub-optional configuration where all virtqueues
share a single vector.
This change does not break live migration compatibility since
vhost-user-fs-pci devices are not migratable yet.
Reported-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20191209110759.35227-1-stefanha@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
The property doesn't make much sense for a vhost-user device.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20191116112016.14872-1-marcandre.lureau@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
It's been marked as deprecated since QEMU v4.1, time to remove it now.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Greg Kurz <groug@kaod.org>
Commit 7e46261368 converted virtfs-proxy-helper to using libcap-ng. There
aren't any users of libcap anymore. No need to install libcap-dev.
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Acked-by: Alex Bennée <alex.bennee@linaro.org>
We currently enable libcap-dev in build-clang to pick up the 9p proxy
helper. Paolo's patch changes (commit 7e46261368) that to use
libcap-ng, so switch to using it. This also means we'll be testing the
scsi pr manager and the bridge helper.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Acked-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
[groug, mention SHA1 that dropped libcap]
Signed-off-by: Greg Kurz <groug@kaod.org>
Libcap was dropped from virtio-9p (commit 7e46261368), so remove it from
the dockerfiles as well.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Acked-by: Alex Bennée <alex.bennee@linaro.org>
[groug, mention SHA1 that dropped libcap]
Signed-off-by: Greg Kurz <groug@kaod.org>
- Fix a regression that broke bitmap deletion without a transaction,
and causes a crash with transaction (only transaction is new to 4.2),
when a qcow2 file contains persistent bitmaps from prior shutdown
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEccLMIrHEYCkn0vOqp6FrSiUnQ2oFAl3uaBMACgkQp6FrSiUn
Q2rX+Af8Dn6cklzAizMLWCvXgEmbUhEvcVp5Gc9w34McCYokQaFDtNDuoShDIksa
F01uP3TlKYd8JoMiGihqVP1mcof8dyGBNMX1fVr2iYIet0h7OAtzOfatXiHmaz4g
r3utlx+0BHm+m9jhwsnCKp24ERa9izGmFQAIyaFLarGdasr29ArepCEXGXiOwtYF
RwD+ioolN9wDcOHjRrEVLHKKRkiX9dSnxKxENahf+M2hVXD+UfbX4cumYxBWOxJQ
qJpTznTA3BxRzUd3/Ue6NL0YmKmXLqHzyeX2Nc1NsdC485nCKn/QZtgI/8yAU0uL
6nseBGa1kgF4+97LwGmPKUmumcxGmQ==
=YAZ1
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/ericb/tags/pull-nbd-2019-12-09' into staging
bitmap fix for 4.2-rc5
- Fix a regression that broke bitmap deletion without a transaction,
and causes a crash with transaction (only transaction is new to 4.2),
when a qcow2 file contains persistent bitmaps from prior shutdown
# gpg: Signature made Mon 09 Dec 2019 15:28:19 GMT
# gpg: using RSA key 71C2CC22B1C4602927D2F3AAA7A16B4A2527436A
# gpg: Good signature from "Eric Blake <eblake@redhat.com>" [full]
# gpg: aka "Eric Blake (Free Software Programmer) <ebb9@byu.net>" [full]
# gpg: aka "[jpeg image of size 6874]" [full]
# Primary key fingerprint: 71C2 CC22 B1C4 6029 27D2 F3AA A7A1 6B4A 2527 436A
* remotes/ericb/tags/pull-nbd-2019-12-09:
block/qcow2-bitmap: fix crash bug in qcow2_co_remove_persistent_dirty_bitmap
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Here is double bug:
First, return error but not set errp. This may lead to:
qmp block-dirty-bitmap-remove may report success when actually failed
block-dirty-bitmap-remove used in a transaction will crash, as
qmp_transaction will think that it returned success and will call
block_dirty_bitmap_remove_commit which will crash, as state->bitmap is
NULL
Second (like in anecdote), this case is not an error at all. As it is
documented in the comment above bdrv_co_remove_persistent_dirty_bitmap
definition, absence of bitmap is not an error, and similar case handled
at start of qcow2_co_remove_persistent_dirty_bitmap, it returns 0 when
there is no bitmaps at all.
But when there are some bitmaps, but not the requested one, it return
error with errp unset.
Fix that.
Trigger:
1. create persistent bitmap A
2. shutdown vm (bitmap A is synced)
3. start vm
4. create persistent bitmap B
5. remove bitmap B - it fails (and crashes if in transaction)
Potential workaround (rather invasive to ask clients to implement it):
1. create persistent bitmap A
2. shutdown vm
3. start vm
4. create persistent bitmap B
5. remember, that we want to remove bitmap B after vm shutdown
...
some other operations
...
6. vm shutdown
7. start vm in stopped mode, and remove all bitmaps marked for removing
8. stop vm
Fixes: b56a1e3175
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-Id: <20191205193049.30666-1-vsementsov@virtuozzo.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
[eblake: commit message tweaks]
Signed-off-by: Eric Blake <eblake@redhat.com>
This is a last minute pull request for ppc-for-4.2. I know it's very
late in freeze, but this does fix a regression: a bad interaction
between the new qemu and SLOF device tree construction code means that
SLOF will crash if PCI to PCI bridges are included in the system.
This PR supersedes ppc-for-4.2-20191206. This one has only a more
minimal change to the firmware addressed only at fixing this bug and
not incorporating some other unrelated changes that happened in the
meantime.
-----BEGIN PGP SIGNATURE-----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=ZWDP
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dgibson/tags/ppc-for-4.2-20191209' into staging
ppc patch queue 2019-12-09
This is a last minute pull request for ppc-for-4.2. I know it's very
late in freeze, but this does fix a regression: a bad interaction
between the new qemu and SLOF device tree construction code means that
SLOF will crash if PCI to PCI bridges are included in the system.
This PR supersedes ppc-for-4.2-20191206. This one has only a more
minimal change to the firmware addressed only at fixing this bug and
not incorporating some other unrelated changes that happened in the
meantime.
# gpg: Signature made Mon 09 Dec 2019 04:52:19 GMT
# gpg: using RSA key 75F46586AE61A66CC44E87DC6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>" [full]
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>" [full]
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>" [full]
# gpg: aka "David Gibson (kernel.org) <dwg@kernel.org>" [unknown]
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dgibson/tags/ppc-for-4.2-20191209:
pseries: Update SLOF firmware image
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
If kvm does not support VMX feature by nested=0, the kvm_vmx_basic
can't get the right value from MSR_IA32_VMX_BASIC register, which
make qemu coredump when qemu do KVM_SET_MSRS.
The coredump info:
error: failed to set MSR 0x480 to 0x0
kvm_put_msrs: Assertion `ret == cpu->kvm_msr_buf->nmsrs' failed.
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Message-Id: <20191206071111.12128-1-yang.zhong@intel.com>
Reported-by: Catherine Ho <catherine.hecx@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Previous implementation in hvf_inject_interrupts() would always inject
VMCS_INTR_T_SWINTR even when VMCS_INTR_T_HWINTR was required. Now
correctly determine when VMCS_INTR_T_HWINTR is appropriate versus
VMCS_INTR_T_SWINTR.
Make sure to clear ins_len and has_error_code when ins_len isn't
valid and error_code isn't set.
Signed-off-by: Cameron Esfahani <dirty@apple.com>
Message-Id: <bf8d945ea1b423786d7802bbcf769517d1fd01f8.1575330463.git.dirty@apple.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
raw_aio_attach_aio_context() passes uninitialized Error *local_err by
reference to laio_init() via aio_setup_linux_aio(). When laio_init()
fails, it passes it on to error_setg_errno(), tripping error_setv()'s
assertion unless @local_err is null by dumb luck.
Fix by initializing @local_err properly.
Fixes: ed6e216171
Cc: Nishanth Aravamudan <naravamudan@digitalocean.com>
Cc: Stefan Hajnoczi <stefanha@redhat.com>
Cc: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20191130194240.10517-4-armbru@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Functions that take an Error ** parameter to pass an error to the
caller expect the parameter to point to null.
failover_replug_primary() violates this precondition in several
places:
* After qemu_opts_from_qdict() failed, *errp is no longer null.
Passing it to error_setg() is wrong, and will trip the assertion in
error_setv(). Messed up in commit 150ab54aa6 "net/virtio: fix
re-plugging of primary device". Simply drop the error_setg().
* Passing @errp to qemu_opt_set_bool(), hotplug_handler_pre_plug(),
and hotplug_handler_plug() is wrong. If one of the first two fails,
*errp is no longer null. Risks tripping the same assertion.
Moreover, continuing after such errors is unsafe. Messed up in
commit 9711cd0dfc "net/virtio: add failover support". Fix by
handling each error properly.
failover_replug_primary() crashes when passed a null @errp. Also
messed up in commit 9711cd0dfc. This bug can't bite as no caller
actually passes null. Fix it anyway.
Fixes: 9711cd0dfc
Fixes: 150ab54aa6
Cc: Jens Freimann <jfreimann@redhat.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20191130194240.10517-3-armbru@redhat.com>
Reviewed-by: Jens Freimann <jfreimann@redhat.com>
virtio_net_handle_migration_primary() returns early when it can't
ensure n->primary_dev is non-null. Checking it again right after that
early return is redundant. Drop.
If n->primary_dev is null on entering failover_replug_primary(), @pdev
will become null, and pdev->partially_hotplugged will crash. Checking
n->primary_dev later is useless. It can't actually be null, because
its caller virtio_net_handle_migration_primary() ensures it isn't.
Drop the useless check.
Cc: Jens Freimann <jfreimann@redhat.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20191130194240.10517-2-armbru@redhat.com>
Reviewed-by: Jens Freimann <jfreimann@redhat.com>
virtfs-proxy-helper is the only user of libcap; everyone else is using
the simpler libcap-ng API. Switch and remove the configure code to
detect libcap.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
[groug: - drop remaining -lcap from Makefile
- fix error message in configure]
Signed-off-by: Greg Kurz <groug@kaod.org>
It's broken so it's no longer helping. The latest Xcode is covered by
Cirrus.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20191127132430.3681-1-alex.bennee@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
