Currently, a set of default flash devices is created at machine init
and drives defined on the QEMU command line are associated to the FMC
and SPI controllers in sequence :
-drive file<file>,format=raw,if=mtd
-drive file<file1>,format=raw,if=mtd
The CS lines are wired in the same creation loop. This makes a strong
assumption on the ordering and is not very flexible since only a
limited set of flash devices can be defined : 1 FMC + 1 or 2 SPI,
which is less than what the SoC really supports.
A better alternative would be to define the flash devices on the
command line using a blockdev attached to a CS line of a SSI bus :
-blockdev node-name=fmc0,driver=file,filename=./flash.img
-device mx66u51235f,cs=0x0,bus=ssi.0,drive=fmc0
However, user created flash devices are not correctly wired to their
SPI controller and consequently can not be used by the machine. Fix
that and wire the CS lines of all available devices when the SSI bus
is reset.
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Simple routine to retrieve a DeviceState object on a SPI bus using its
CS index. It will be useful for the board to wire the CS lines.
Cc: Alistair Francis <alistair@alistair23.me>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Boards will use this new property to identify the device CS line and
wire the SPI controllers accordingly.
Cc: Alistair Francis <alistair@alistair23.me>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Switch to the latest v8.06 release which introduces interesting
changes for the AST2600 I2C and I3C models. Also take the AST2600 A2
images instead of the default since QEMU tries to model The AST2600 A3
SoC.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Added support for the buffer organization option in pool buffer control
register.when set to 1,The buffer is split into two parts: Lower 16 bytes
for Tx and higher 16 bytes for Rx.
Signed-off-by: Hang Yu <francis_yuu@stu.pku.edu.cn>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
[ clg: checkpatch fixes ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
According to the ast2600 datasheet and the linux aspeed i2c driver,
the TXBUF transmission start position should be TXBUF[0] instead
of TXBUF[1],so the arg pool_start is useless,and the address is not
included in TXBUF.So even if Tx Count equals zero,there is at least
1 byte data needs to be transmitted,and M_TX_CMD should not be cleared
at this condition.The driver url is:
https://github.com/AspeedTech-BMC/linux/blob/aspeed-master-v5.15/drivers/i2c/busses/i2c-ast2600.c
Signed-off-by: Hang Yu <francis_yuu@stu.pku.edu.cn>
Fixes: 6054fc73e8 ("aspeed/i2c: Add support for pool buffer transfers")
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Fixed inconsistency between the regisiter bit field definition header file
and the ast2600 datasheet. The reg name is I2CD1C:Pool Buffer Control
Register in old register mode and I2CC0C: Master/Slave Pool Buffer Control
Register in new register mode. They share bit field
[12:8]:Transmit Data Byte Count and bit field
[29:24]:Actual Received Pool Buffer Size according to the datasheet.
According to the ast2600 datasheet,the actual Tx count is
Transmit Data Byte Count plus 1, and the max Rx size is
Receive Pool Buffer Size plus 1, both in Pool Buffer Control Register.
The version before forgot to plus 1, and mistake Rx count for Rx size.
Signed-off-by: Hang Yu <francis_yuu@stu.pku.edu.cn>
Fixes: 3be3d6ccf2 ("aspeed: i2c: Migrate to registerfields API")
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
On 32-bit hosts, RAM has a 2047 MB limit. Use a macro to define the
default ram size of machines (AST2600 SoC) that can have 2 GB.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
* Some of the preliminary patches for Cortex-A710 support
* i.MX7 and i.MX6UL refactoring
* Implement SRC device for i.MX7
* Catch illegal-exception-return from EL3 with bad NSE/NS
* Use 64-bit offsets for holding time_t differences in RTC devices
* Model correct number of MPU regions for an505, an521, an524 boards
-----BEGIN PGP SIGNATURE-----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=MFh3
-----END PGP SIGNATURE-----
Merge tag 'pull-target-arm-20230831' of https://git.linaro.org/people/pmaydell/qemu-arm into staging
target-arm queue:
* Some of the preliminary patches for Cortex-A710 support
* i.MX7 and i.MX6UL refactoring
* Implement SRC device for i.MX7
* Catch illegal-exception-return from EL3 with bad NSE/NS
* Use 64-bit offsets for holding time_t differences in RTC devices
* Model correct number of MPU regions for an505, an521, an524 boards
# -----BEGIN PGP SIGNATURE-----
#
# iQJNBAABCAA3FiEE4aXFk81BneKOgxXPPCUl7RQ2DN4FAmTwbukZHHBldGVyLm1h
# eWRlbGxAbGluYXJvLm9yZwAKCRA8JSXtFDYM3ihBD/wK8Iz0KpTAwZBDAodnSZrh
# tQnJAvYFp8CxA4O8sZ9IeWsZh90gzsTCZi0NqUTTzvWCJfxkB7qTPdlJT5IzVxou
# oEUk2aogSJhRA3XRJzqArXsPlnZGSYDbtwKx4VtfCvOCCH08Y7nhnFaRj1oFnR4Q
# 0PE/8YtGXTBxLHrO8U3tomg7zElzOUP8ZVZtb30BOyw1jtfSD03IZR8dzpA43u1E
# Hh418WvVekmwFoFNh8yUeHzbyXMZufzvbJPuDGJ8pPWwIpvSG6chOnKF8jZll+Ur
# DqOsDkGlQgcBR2QwYfSPClrEkX8yahJ95PBfM6giG+DQC7OiElqXqTiUGZcpgUVo
# uSUbzS4YPsxCnyVV6SBXV+f/8hdXBxOSHTgl7OAFa8X9OwWwspxHJ/v2o/2ibnUT
# hTTkFp/w1nQwVEN8xf1DOUpm/J2Wr8UeH4f776daSrfKAol2BKbHb8dOgGLQCwqb
# G+iDcE4bkzRqly6f+uVk8xSEZDd9P1NYoxKV+gNlV1dTspdHVpTC+rXMa8dRw5hI
# 4KgaAslj++Xa229xkjORXCJ1cICRIebYg7+SjvTtGBYsFV7plsCcYb/R9yLmhVCf
# fKHKKaYe9sQJ82apOIkTc+nnW8BQQx6XUmU/A//iZ8JGLk6DpJcZ8f1m/2rVZTsl
# 9+lsmpBf4w+uR4o+Womhfw==
# =MFh3
# -----END PGP SIGNATURE-----
# gpg: Signature made Thu 31 Aug 2023 06:43:53 EDT
# gpg: using RSA key E1A5C593CD419DE28E8315CF3C2525ED14360CDE
# gpg: issuer "peter.maydell@linaro.org"
# gpg: Good signature from "Peter Maydell <peter.maydell@linaro.org>" [full]
# gpg: aka "Peter Maydell <pmaydell@gmail.com>" [full]
# gpg: aka "Peter Maydell <pmaydell@chiark.greenend.org.uk>" [full]
# gpg: aka "Peter Maydell <peter@archaic.org.uk>" [unknown]
# Primary key fingerprint: E1A5 C593 CD41 9DE2 8E83 15CF 3C25 25ED 1436 0CDE
* tag 'pull-target-arm-20230831' of https://git.linaro.org/people/pmaydell/qemu-arm: (24 commits)
hw/arm: Set number of MPU regions correctly for an505, an521, an524
hw/arm/armv7m: Add mpu-ns-regions and mpu-s-regions properties
target/arm: Do all "ARM_FEATURE_X implies Y" checks in post_init
rtc: Use time_t for passing and returning time offsets
hw/rtc/aspeed_rtc: Use 64-bit offset for holding time_t difference
hw/rtc/twl92230: Use int64_t for sec_offset and alm_sec
hw/rtc/m48t59: Use 64-bit arithmetic in set_alarm()
target/arm: Catch illegal-exception-return from EL3 with bad NSE/NS
Add i.MX7 SRC device implementation
Add i.MX7 missing TZ devices and memory regions
Refactor i.MX7 processor code
Add i.MX6UL missing devices.
Refactor i.MX6UL processor code
Remove i.MX7 IOMUX GPR device from i.MX6UL
target/arm: properly document FEAT_CRC32
target/arm: Implement FEAT_HPDS2 as a no-op
target/arm: Suppress FEAT_TRBE (Trace Buffer Extension)
target/arm: Apply access checks to neoverse-v1 special registers
target/arm: Apply access checks to neoverse-n1 special registers
target/arm: Introduce make_ccsidr64
...
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
- enable ccache for gitlab builds
- fix various test info leakages for non V=1
- update style to allow loop vars
- bump FreeBSD to v13.2
- clean-up gdbstub tests
- various gdbstub doc and refactorings
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEZoWumedRZ7yvyN81+9DbCVqeKkQFAmTvS2AACgkQ+9DbCVqe
KkRiRwgAhsinp2/KgnvkD0n6deQy/JWg9MfYIvvZacKEakIfQvCDoJ752AUZzUTw
ggQ+W2KuaoHTzwG+AOMLdzulkmspQ8xeFuD2aIpFjRMnZrO9jN2T4L0vcGLAd95c
9QLqPeH8xRdhuK28+ILuYzKOKBcefQ44ufMLpxrS2iNITEsSg/Tw3MU91hbct49g
3OR4bD1ueG5Ib/lXp8V/4GnRmfLdnp3k0i/6OHriq7Mpz4Lia67WblVsPEple66U
n7JCo2sI5/m+6p2tvKs7rH60xc8s1Za3kbK4ggEq3LVRfzVOordZqO+1ep6wklTY
6nP9Ry9nZG3gqCmcNXfhoofm0vHaZA==
=Km9m
-----END PGP SIGNATURE-----
Merge tag 'pull-maintainer-ominbus-300823-1' of https://gitlab.com/stsquad/qemu into staging
testing and gdbstub updates:
- enable ccache for gitlab builds
- fix various test info leakages for non V=1
- update style to allow loop vars
- bump FreeBSD to v13.2
- clean-up gdbstub tests
- various gdbstub doc and refactorings
# -----BEGIN PGP SIGNATURE-----
#
# iQEzBAABCgAdFiEEZoWumedRZ7yvyN81+9DbCVqeKkQFAmTvS2AACgkQ+9DbCVqe
# KkRiRwgAhsinp2/KgnvkD0n6deQy/JWg9MfYIvvZacKEakIfQvCDoJ752AUZzUTw
# ggQ+W2KuaoHTzwG+AOMLdzulkmspQ8xeFuD2aIpFjRMnZrO9jN2T4L0vcGLAd95c
# 9QLqPeH8xRdhuK28+ILuYzKOKBcefQ44ufMLpxrS2iNITEsSg/Tw3MU91hbct49g
# 3OR4bD1ueG5Ib/lXp8V/4GnRmfLdnp3k0i/6OHriq7Mpz4Lia67WblVsPEple66U
# n7JCo2sI5/m+6p2tvKs7rH60xc8s1Za3kbK4ggEq3LVRfzVOordZqO+1ep6wklTY
# 6nP9Ry9nZG3gqCmcNXfhoofm0vHaZA==
# =Km9m
# -----END PGP SIGNATURE-----
# gpg: Signature made Wed 30 Aug 2023 10:00:00 EDT
# gpg: using RSA key 6685AE99E75167BCAFC8DF35FBD0DB095A9E2A44
# gpg: Good signature from "Alex Bennée (Master Work Key) <alex.bennee@linaro.org>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 6685 AE99 E751 67BC AFC8 DF35 FBD0 DB09 5A9E 2A44
* tag 'pull-maintainer-ominbus-300823-1' of https://gitlab.com/stsquad/qemu:
gdbstub: move comment for gdb_register_coprocessor
gdbstub: replace global gdb_has_xml with a function
gdbstub: refactor get_feature_xml
gdbstub: remove unused user_ctx field
gdbstub: fixes cases where wrong threads were reported to GDB on SIGINT
tests/tcg: clean-up gdb confirm/pagination settings
tests: remove test-gdbstub.py
.gitlab-ci.d/cirrus.yml: Update FreeBSD to v13.2
docs/style: permit inline loop variables
tests/tcg: remove quoting for info output
tests/docker: cleanup non-verbose output
gitlab: enable ccache for many build jobs
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
The IoTKit, SSE200 and SSE300 all default to 8 MPU regions. The
MPS2/MPS3 FPGA images don't override these except in the case of
AN547, which uses 16 MPU regions.
Define properties on the ARMSSE object for the MPU regions (using the
same names as the documented RTL configuration settings, and
following the pattern we already have for this device of using
all-caps names as the RTL does), and set them in the board code.
We don't actually need to override the default except on AN547,
but it's simpler code to have the board code set them always
rather than tracking which board subtypes want to set them to
a non-default value separately from what that value is.
Tho overall effect is that for mps2-an505, mps2-an521 and mps3-an524
we now correctly use 8 MPU regions, while mps3-an547 stays at its
current 16 regions.
It's possible some guest code wrongly depended on the previous
incorrectly modeled number of memory regions. (Such guest code
should ideally check the number of regions via the MPU_TYPE
register.) The old behaviour can be obtained with additional
-global arguments to QEMU:
For mps2-an521 and mps2-an524:
-global sse-200.CPU0_MPU_NS=16 -global sse-200.CPU0_MPU_S=16 -global sse-200.CPU1_MPU_NS=16 -global sse-200.CPU1_MPU_S=16
For mps2-an505:
-global sse-200.CPU0_MPU_NS=16 -global sse-200.CPU0_MPU_S=16
NB that the way the implementation allows this use of -global
is slightly fragile: if the board code explicitly sets the
properties on the sse-200 object, this overrides the -global
command line option. So we rely on:
- the boards that need fixing all happen to use the SSE defaults
- we can write the board code to only set the property if it
is different from the default, rather than having all boards
explicitly set the property
- the board that does need to use a non-default value happens
to need to set it to the same value (16) we previously used
This works, but there are some kinds of refactoring of the
mps2-tz.c code that would break the support for -global here.
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1772
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20230724174335.2150499-4-peter.maydell@linaro.org
M-profile CPUs generally allow configuration of the number of MPU
regions that they have. We don't currently model this, so our
implementations of some of the board models provide CPUs with the
wrong number of regions. RTOSes like Zephyr that hardcode the
expected number of regions may therefore not run on the model if they
are set up to run on real hardware.
Add properties mpu-ns-regions and mpu-s-regions to the ARMV7M object,
matching the ability of hardware to configure the number of Secure
and NonSecure regions separately. Our actual CPU implementation
doesn't currently support that, and it happens that none of the MPS
boards we model set the number of regions differently for Secure vs
NonSecure, so we provide an interface to the boards and SoCs that
won't need to change if we ever do add that functionality in future,
but make it an error to configure the two properties to different
values.
(The property name on the CPU is the somewhat misnamed-for-M-profile
"pmsav7-dregion", so we don't follow that naming convention for
the properties here. The TRM doesn't say what the CPU configuration
variable names are, so we pick something, and follow the lowercase
convention we already have for properties here.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20230724174335.2150499-3-peter.maydell@linaro.org
Where architecturally one ARM_FEATURE_X flag implies another
ARM_FEATURE_Y, we allow the CPU init function to only set X, and then
set Y for it. Currently we do this in two places -- we set a few
flags in arm_cpu_post_init() because we need them to decide which
properties to create on the CPU object, and then we do the rest in
arm_cpu_realizefn(). However, this is fragile, because it's easy to
add a new property and not notice that this means that an X-implies-Y
check now has to move from realize to post-init.
As a specific example, the pmsav7-dregion property is conditional
on ARM_FEATURE_PMSA && ARM_FEATURE_V7, which means it won't appear
on the Cortex-M33 and -M55, because they set ARM_FEATURE_V8 and
rely on V8-implies-V7, which doesn't happen until the realizefn.
Move all of these X-implies-Y checks into a new function, which
we call at the top of arm_cpu_post_init(), so the feature bits
are available at that point.
This does now give us the reverse issue, that if there's a feature
bit which is enabled or disabled by the setting of a property then
then X-implies-Y features that are dependent on that property need to
be in realize, not in this new function. But the only one of those
is the "EL3 implies VBAR" which is already in the right place, so
putting things this way round seems better to me.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20230724174335.2150499-2-peter.maydell@linaro.org
The functions qemu_get_timedate() and qemu_timedate_diff() take
and return a time offset as an integer. Coverity points out that
means that when an RTC device implementation holds an offset
as a time_t, as the m48t59 does, the time_t will get truncated.
(CID 1507157, 1517772).
The functions work with time_t internally, so make them use that type
in their APIs.
Note that this won't help any Y2038 issues where either the device
model itself is keeping the offset in a 32-bit integer, or where the
hardware under emulation has Y2038 or other rollover problems. If we
missed any cases of the former then hopefully Coverity will warn us
about them since after this patch we'd be truncating a time_t in
assignments from qemu_timedate_diff().)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
In the aspeed_rtc device we store a difference between two time_t
values in an 'int'. This is not really correct when time_t could
be 64 bits. Enlarge the field to 'int64_t'.
This is a migration compatibility break for the aspeed boards.
While we are changing the vmstate, remove the accidental
duplicate of the offset field.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
In the twl92230 device, use int64_t for the two state fields
sec_offset and alm_sec, because we set these to values that
are either time_t or differences between two time_t values.
These fields aren't saved in vmstate anywhere, so we can
safely widen them.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
In the m48t59 device we almost always use 64-bit arithmetic when
dealing with time_t deltas. The one exception is in set_alarm(),
which currently uses a plain 'int' to hold the difference between two
time_t values. Switch to int64_t instead to avoid any possible
overflow issues.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
The architecture requires (R_TYTWB) that an attempt to return from EL3
when SCR_EL3.{NSE,NS} are {1,0} is an illegal exception return. (This
enforces that the CPU can't ever be executing below EL3 with the
NSE,NS bits indicating an invalid security state.)
We were missing this check; add it.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20230807150618.101357-1-peter.maydell@linaro.org
The SRC device is normally used to start the secondary CPU.
When running Linux directly, QEMU is emulating a PSCI interface that UBOOT
is installing at boot time and therefore the fact that the SRC device is
unimplemented is hidden as Qemu respond directly to PSCI requets without
using the SRC device.
But if you try to run a more bare metal application (maybe uboot itself),
then it is not possible to start the secondary CPU as the SRC is an
unimplemented device.
This patch adds the ability to start the secondary CPU through the SRC
device so that you can use this feature in bare metal applications.
Signed-off-by: Jean-Christophe Dubois <jcd@tribudubois.net>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: ce9a0162defd2acee5dc7f8a674743de0cded569.1692964892.git.jcd@tribudubois.net
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* Add TZASC as unimplemented device.
- Allow bare metal application to access this (unimplemented) device
* Add CSU as unimplemented device.
- Allow bare metal application to access this (unimplemented) device
* Add various memory segments
- OCRAM
- OCRAM EPDC
- OCRAM PXP
- OCRAM S
- ROM
- CAAM
Signed-off-by: Jean-Christophe Dubois <jcd@tribudubois.net>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: f887a3483996ba06d40bd62ffdfb0ecf68621987.1692964892.git.jcd@tribudubois.net
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* Add Addr and size definition for all i.MX7 devices in i.MX7 header file.
* Use those newly defined named constants whenever possible.
* Standardize the way we init a familly of unimplemented devices
- SAI
- PWM
- CAN
* Add/rework few comments
Signed-off-by: Jean-Christophe Dubois <jcd@tribudubois.net>
Message-id: 59e195d33e4d486a8d131392acd46633c8c10ed7.1692964892.git.jcd@tribudubois.net
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* Add TZASC as unimplemented device.
- Allow bare metal application to access this (unimplemented) device
* Add CSU as unimplemented device.
- Allow bare metal application to access this (unimplemented) device
* Add 4 missing PWM devices
Signed-off-by: Jean-Christophe Dubois <jcd@tribudubois.net>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 59e4dc56e14eccfefd379275ec19048dff9c10b3.1692964892.git.jcd@tribudubois.net
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* Add Addr and size definition for most i.MX6UL devices in i.MX6UL header file.
* Use those newly defined named constants whenever possible.
* Standardize the way we init a familly of unimplemented devices
- SAI
- PWM
- CAN
* Add/rework few comments
Signed-off-by: Jean-Christophe Dubois <jcd@tribudubois.net>
Message-id: d579043fbd4e4b490370783fda43fc02c8e9be75.1692964892.git.jcd@tribudubois.net
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
i.MX7 IOMUX GPR device is not equivalent to i.MX6UL IOMUXC GPR device.
In particular, register 22 is not present on i.MX6UL and this is actualy
The only register that is really emulated in the i.MX7 IOMUX GPR device.
Note: The i.MX6UL code is actually also implementing the IOMUX GPR device
as an unimplemented device at the same bus adress and the 2 instantiations
were actualy colliding. So we go back to the unimplemented device for now.
Signed-off-by: Jean-Christophe Dubois <jcd@tribudubois.net>
Message-id: 48681bf51ee97646479bb261bee19abebbc8074e.1692964892.git.jcd@tribudubois.net
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This is a mandatory feature for Armv8.1 architectures but we don't
state the feature clearly in our emulation list. Also include
FEAT_CRC32 comment in aarch64_max_tcg_initfn for ease of grepping.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20230824075406.1515566-1-alex.bennee@linaro.org
Cc: qemu-stable@nongnu.org
Message-Id: <20230222110104.3996971-1-alex.bennee@linaro.org>
[PMM: pluralize 'instructions' in docs]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This feature allows the operating system to set TCR_ELx.HWU*
to allow the implementation to use the PBHA bits from the
block and page descriptors for for IMPLEMENTATION DEFINED
purposes. Since QEMU has no need to use these bits, we may
simply ignore them.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20230811214031.171020-11-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Like FEAT_TRF (Self-hosted Trace Extension), suppress tracing
external to the cpu, which is out of scope for QEMU.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20230811214031.171020-10-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
There is only one additional EL1 register modeled, which
also needs to use access_actlr_w.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20230811214031.171020-8-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Access to many of the special registers is enabled or disabled
by ACTLR_EL[23], which we implement as constant 0, which means
that all writes outside EL3 should trap.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20230811214031.171020-7-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Do not hard-code the constants for Neoverse V1.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20230811214031.171020-6-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When the cpu support MTE, but the system does not, reduce cpu
support to user instructions at EL0 instead of completely
disabling MTE. If we encounter a cpu implementation which does
something else, we can revisit this setting.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20230811214031.171020-5-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Support all of the easy GM block sizes.
Use direct memory operations, since the pointers are aligned.
While BS=2 (16 bytes, 1 tag) is a legal setting, that requires
an atomic store of one nibble. This is not difficult, but there
is also no point in supporting it until required.
Note that cortex-a710 sets GM blocksize to match its cacheline
size of 64 bytes. I expect many implementations will also
match the cacheline, which makes 16 bytes very unlikely.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20230811214031.171020-4-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Previously we hard-coded the blocksize with GMID_EL1_BS.
But the value we choose for -cpu max does not match the
value that cortex-a710 uses.
Mirror the way we handle dcz_blocksize.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20230811214031.171020-3-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This value is only 4 bits wide.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20230811214031.171020-2-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In order to use virtio backends we need to initialize RAM for the
xen-mapcache (which is responsible for mapping guest memory using foreign
mapping) to work. Calculate and add hi/low memory regions based on
machine->ram_size.
Use the constants defined in public header arch-arm.h to be aligned with the xen
toolstack.
While using this machine, the toolstack should then pass real ram_size using
"-m" arg. If "-m" is not given, create a QEMU machine without IOREQ and other
emulated devices like TPM and VIRTIO. This is done to keep this QEMU machine
usable for /etc/init.d/xencommons.
Signed-off-by: Oleksandr Tyshchenko <oleksandr_tyshchenko@epam.com>
Signed-off-by: Vikram Garhwal <vikram.garhwal@amd.com>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
Signed-off-by: Stefano Stabellini <stefano.stabellini@amd.com>
In order to use virtio backends we need to allocate virtio-mmio
parameters (irq and base) and register corresponding buses.
Use the constants defined in public header arch-arm.h to be
aligned with the toolstack. So the number of current supported
virtio-mmio devices is 10.
For the interrupts triggering use already existing on Arm
device-model hypercall.
The toolstack should then insert the same amount of device nodes
into guest device-tree.
Signed-off-by: Oleksandr Tyshchenko <oleksandr_tyshchenko@epam.com>
Signed-off-by: Vikram Garhwal <vikram.garhwal@amd.com>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
Signed-off-by: Stefano Stabellini <stefano.stabellini@amd.com>
For the moment, move PRAGMA_DISABLE_PACKED_WARNING and
PRAGMA_ENABLE_PACKED_WARNING back to bsd-user/qemu.h.
Of course, these should be in compiler.h, but that interferes with too
many things at the moment, so take one step back to unbreak clang
linux-user builds first. Use the exact same version that's in
linux-user/qemu.h since that's what should be in compiler.h.
Signed-off-by: Warner Losh <imp@bsdimp.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Use proper kdoc style comments for this API function.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20230829161528.2707696-13-alex.bennee@linaro.org>
Try and make the self reported global hack a little less hackish by
providing a query function instead. As gdb_has_xml was always set if
we negotiated XML we can now use the presence of ->target_xml as the
test instead.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20230829161528.2707696-12-alex.bennee@linaro.org>
Try to bring up the code to more modern standards by:
- use dynamic GString built xml over a fixed buffer
- use autofree to save on explicit g_free() calls
- don't hand hack strstr to find the delimiter
- fix up style of xml_builtin and invert loop
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20230829161528.2707696-11-alex.bennee@linaro.org>
This was always NULL so drop it.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Acked-by: Ilya Leoshkevich <iii@linux.ibm.com>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20230829161528.2707696-10-alex.bennee@linaro.org>
This fix is implemented by having the vCont handler set the value of
`gdbserver_state.c_cpu` if any threads are to be resumed. The specific
CPU picked is arbitrarily from the ones to be resumed, but it should
be okay, as all GDB cares about is that it is a resumed thread.
Signed-off-by: Matheus Branco Borella <dark.ryu.550@gmail.com>
Message-Id: <20230804182633.47300-2-dark.ryu.550@gmail.com>
[AJB: style and whitespace fixes]
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1725
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20230829161528.2707696-9-alex.bennee@linaro.org>
We can do this all in the run-test.py script so remove the extraneous
bits from the individual tests which got copied from the original
non-CI gdb tests.
Acked-by: Ilya Leoshkevich <iii@linux.ibm.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20230829161528.2707696-8-alex.bennee@linaro.org>
This isn't directly called by our CI and because it doesn't run via
our run-test.py script does things slightly differently. Lets remove
it as we have plenty of working in-tree tests now for various aspects
of gdbstub.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20230829161528.2707696-7-alex.bennee@linaro.org>
The FreeBSD CI job started to fail due to linking problems ... time
to update to the latest version to get this fixed.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Message-Id: <20230823144533.230477-1-thuth@redhat.com>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20230829161528.2707696-6-alex.bennee@linaro.org>
I've already wasted enough of my time debugging aliased variables in
deeply nested loops. While not scattering variable declarations around
is a good aim I think we can make an exception for stuff used inside a
loop.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Acked-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20230829161528.2707696-5-alex.bennee@linaro.org>
This avoids ugly multi-line wrapping for the test on non V=1 builds.
Acked-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20230829161528.2707696-4-alex.bennee@linaro.org>
Even with --quiet docker will spam the sha256 to the console. Avoid
this by redirecting stdout. While we are at it fix the name we echo
which was broken during 0b1a649047 (tests/docker: use direct RUNC call
to build containers).
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20230829161528.2707696-3-alex.bennee@linaro.org>
