Currently, block_copy operation lock the whole requested region. But
there is no reason to lock clusters, which are already copied, it will
disturb other parallel block_copy requests for no reason.
Let's instead do the following:
Lock only sub-region, which we are going to operate on. Then, after
copying all dirty sub-regions, we should wait for intersecting
requests block-copy, if they failed, we should retry these new dirty
clusters.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Andrey Shinkevich <andrey.shinkevich@virtuozzo.com>
Message-Id: <20200311103004.7649-9-vsementsov@virtuozzo.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
offset/bytes pair is more usual naming in block layer, let's use it.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Andrey Shinkevich <andrey.shinkevich@virtuozzo.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Message-Id: <20200311103004.7649-8-vsementsov@virtuozzo.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
We have a lot of "chunk_end - start" invocations, let's switch to
bytes/cur_bytes scheme instead.
While being here, improve check on block_copy_do_copy parameters to not
overflow when calculating nbytes and use int64_t for bytes in
block_copy for consistency.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Andrey Shinkevich <andrey.shinkevich@virtuozzo.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Message-Id: <20200311103004.7649-7-vsementsov@virtuozzo.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
Split find_conflicting_inflight_req to be used separately.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Andrey Shinkevich <andrey.shinkevich@virtuozzo.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Message-Id: <20200311103004.7649-6-vsementsov@virtuozzo.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
Use bdrv_block_status_above to chose effective chunk size and to handle
zeroes effectively.
This substitutes checking for just being allocated or not, and drops
old code path for it. Assistance by backup job is dropped too, as
caching block-status information is more difficult than just caching
is-allocated information in our dirty bitmap, and backup job is not
good place for this caching anyway.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Andrey Shinkevich <andrey.shinkevich@virtuozzo.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Message-Id: <20200311103004.7649-5-vsementsov@virtuozzo.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
In block_copy_do_copy we fallback to read+write if copy_range failed.
In this case copy_size is larger than defined for buffered IO, and
there is corresponding commit. Still, backup copies data cluster by
cluster, and most of requests are limited to one cluster anyway, so the
only source of this one bad-limited request is copy-before-write
operation.
Further patch will move backup to use block_copy directly, than for
cases where copy_range is not supported, first request will be
oversized in each backup. It's not good, let's change it now.
Fix is simple: just limit first copy_range request like buffer-based
request. If it succeed, set larger copy_range limit.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Andrey Shinkevich <andrey.shinkevich@virtuozzo.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Message-Id: <20200311103004.7649-4-vsementsov@virtuozzo.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
Assume we have two regions, A and B, and region B is in-flight now,
region A is not yet touched, but it is unallocated and should be
skipped.
Correspondingly, as progress we have
total = A + B
current = 0
If we reset unallocated region A and call progress_reset_callback,
it will calculate 0 bytes dirty in the bitmap and call
job_progress_set_remaining, which will set
total = current + 0 = 0 + 0 = 0
So, B bytes are actually removed from total accounting. When job
finishes we'll have
total = 0
current = B
, which doesn't sound good.
This is because we didn't considered in-flight bytes, actually when
calculating remaining, we should have set (in_flight + dirty_bytes)
as remaining, not only dirty_bytes.
To fix it, let's refactor progress calculation, moving it to block-copy
itself instead of fixing callback. And, of course, track in_flight
bytes count.
We still have to keep one callback, to maintain backup job bytes_read
calculation, but it will go on soon, when we turn the whole backup
process into one block_copy call.
Cc: qemu-stable@nongnu.org
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Andrey Shinkevich <andrey.shinkevich@virtuozzo.com>
Message-Id: <20200311103004.7649-3-vsementsov@virtuozzo.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
On success path we return what inflate() returns instead of 0. And it
most probably works for Z_STREAM_END as it is positive, but is
definitely broken for Z_BUF_ERROR.
While being here, switch to errno return code, to be closer to
qcow2_compress API (and usual expectations).
Revert condition in if to be more positive. Drop dead initialization of
ret.
Cc: qemu-stable@nongnu.org # v4.0
Fixes: 341926ab83
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-Id: <20200302150930.16218-1-vsementsov@virtuozzo.com>
Reviewed-by: Alberto Garcia <berto@igalia.com>
Reviewed-by: Ján Tomko <jtomko@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
'crypto_opts' forgot to free in qcow2_close(), this patch fix the bellow leak stack:
Direct leak of 24 byte(s) in 1 object(s) allocated from:
#0 0x7f0edd81f970 in __interceptor_calloc (/lib64/libasan.so.5+0xef970)
#1 0x7f0edc6d149d in g_malloc0 (/lib64/libglib-2.0.so.0+0x5249d)
#2 0x55d7eaede63d in qobject_input_start_struct /mnt/sdb/qemu-new/qemu_test/qemu/qapi/qobject-input-visitor.c:295
#3 0x55d7eaed78b8 in visit_start_struct /mnt/sdb/qemu-new/qemu_test/qemu/qapi/qapi-visit-core.c:49
#4 0x55d7eaf5140b in visit_type_QCryptoBlockOpenOptions qapi/qapi-visit-crypto.c:290
#5 0x55d7eae43af3 in block_crypto_open_opts_init /mnt/sdb/qemu-new/qemu_test/qemu/block/crypto.c:163
#6 0x55d7eacd2924 in qcow2_update_options_prepare /mnt/sdb/qemu-new/qemu_test/qemu/block/qcow2.c:1148
#7 0x55d7eacd33f7 in qcow2_update_options /mnt/sdb/qemu-new/qemu_test/qemu/block/qcow2.c:1232
#8 0x55d7eacd9680 in qcow2_do_open /mnt/sdb/qemu-new/qemu_test/qemu/block/qcow2.c:1512
#9 0x55d7eacdc55e in qcow2_open_entry /mnt/sdb/qemu-new/qemu_test/qemu/block/qcow2.c:1792
#10 0x55d7eacdc8fe in qcow2_open /mnt/sdb/qemu-new/qemu_test/qemu/block/qcow2.c:1819
#11 0x55d7eac3742d in bdrv_open_driver /mnt/sdb/qemu-new/qemu_test/qemu/block.c:1317
#12 0x55d7eac3e990 in bdrv_open_common /mnt/sdb/qemu-new/qemu_test/qemu/block.c:1575
#13 0x55d7eac4442c in bdrv_open_inherit /mnt/sdb/qemu-new/qemu_test/qemu/block.c:3126
#14 0x55d7eac45c3f in bdrv_open /mnt/sdb/qemu-new/qemu_test/qemu/block.c:3219
#15 0x55d7ead8e8a4 in blk_new_open /mnt/sdb/qemu-new/qemu_test/qemu/block/block-backend.c:397
#16 0x55d7eacde74c in qcow2_co_create /mnt/sdb/qemu-new/qemu_test/qemu/block/qcow2.c:3534
#17 0x55d7eacdfa6d in qcow2_co_create_opts /mnt/sdb/qemu-new/qemu_test/qemu/block/qcow2.c:3668
#18 0x55d7eac1c678 in bdrv_create_co_entry /mnt/sdb/qemu-new/qemu_test/qemu/block.c:485
#19 0x55d7eb0024d2 in coroutine_trampoline /mnt/sdb/qemu-new/qemu_test/qemu/util/coroutine-ucontext.c:115
Reported-by: Euler Robot <euler.robot@huawei.com>
Signed-off-by: Pan Nengyuan <pannengyuan@huawei.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Message-Id: <20200227012950.12256-2-pannengyuan@huawei.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
RFC 7230 section 3.2 indicates that HTTP header field names are case
insensitive.
Signed-off-by: David Edmondson <david.edmondson@oracle.com>
Message-Id: <20200224101310.101169-3-david.edmondson@oracle.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
RFC 7230 section 3.2 indicates that whitespace is permitted between
the field name and field value and after the field value.
Signed-off-by: David Edmondson <david.edmondson@oracle.com>
Message-Id: <20200224101310.101169-2-david.edmondson@oracle.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
Add qemu-img measure support in the "luks" block driver.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Message-Id: <20200221112522.1497712-3-stefanha@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
The qcow2 .bdrv_measure() code calculates the crypto payload offset.
This logic really belongs in crypto/block.c where it can be reused by
other image formats.
The "luks" block driver will need this same logic in order to implement
.bdrv_measure(), so extract the qcrypto_block_calculate_payload_offset()
function now.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Message-Id: <20200221112522.1497712-2-stefanha@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20200308092440.23564-12-mlevitsk@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20200308092440.23564-11-mlevitsk@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20200308092440.23564-10-mlevitsk@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20200308092440.23564-9-mlevitsk@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
hmp_snapshot_blkdev is from GPLv2 version of the hmp-cmds.c thus
have to change the licence to GPLv2
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20200308092440.23564-8-mlevitsk@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20200308092440.23564-7-mlevitsk@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Moved code was added after 2012-01-13, thus under GPLv2+
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20200308092440.23564-6-mlevitsk@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Fixed commit message
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20200308092440.23564-5-mlevitsk@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
These days device-hotplug.c only contains the hmp_drive_add
In the next patch, rest of hmp_drive* functions will be moved
there.
Also add block-hmp-cmds.h to contain prototypes of these
functions
License for block-hmp-cmds.h since it contains the code
moved from sysemu.h which lacks license and thus according
to LICENSE is under GPLv2+
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20200308092440.23564-4-mlevitsk@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Clang static code analyzer show warning:
block/file-posix.c:891:9: warning: Value stored to 'op' is never read
op = RAW_PL_ABORT;
^ ~~~~~~~~~~~~
Reported-by: Euler Robot <euler.robot@huawei.com>
Signed-off-by: Chen Qun <kuhn.chenqun@huawei.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <20200302130715.29440-5-kuhn.chenqun@huawei.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Clang static code analyzer show warning:
block/stream.c:186:9: warning: Value stored to 'ret' is never read
ret = 0;
^ ~
Reported-by: Euler Robot <euler.robot@huawei.com>
Signed-off-by: Chen Qun <kuhn.chenqun@huawei.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <20200302130715.29440-3-kuhn.chenqun@huawei.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Starting from ceph Nautilus, RBD has support for namespaces, allowing
for finer grain ACLs on images inside a pool, and tenant isolation.
In the rbd cli tool documentation, the new image-spec and snap-spec are :
- [pool-name/[namespace-name/]]image-name
- [pool-name/[namespace-name/]]image-name@snap-name
When using an non namespace's enabled qemu, it complains about not
finding the image called namespace-name/image-name, thus we only need to
parse the image once again to find if there is a '/' in its name, and if
there is, use what is before it as the name of the namespace to later
pass it to rados_ioctx_set_namespace.
rados_ioctx_set_namespace if called with en empty string or a null
pointer as the namespace parameters pretty much does nothing, as it then
defaults to the default namespace.
The namespace is extracted inside qemu_rbd_parse_filename, stored in the
qdict, and used in qemu_rbd_connect to make it work with both qemu-img,
and qemu itself.
Signed-off-by: Florian Florensa <fflorensa@online.net>
Message-Id: <20200110111513.321728-2-fflorensa@online.net>
Reviewed-by: Jason Dillaman <dillaman@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This adds a --blockdev option to the storage daemon that works the same
as the -blockdev option of the system emulator.
In order to be able to link with blockdev.o, we also need to change
stream.o from common-obj to block-obj, which is where all other block
jobs already are.
In contrast to the system emulator, qemu-storage-daemon options will be
processed in the order they are given. The user needs to take care to
refer to other objects only after defining them.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <20200224143008.13362-7-kwolf@redhat.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
These commands make only sense for system emulators and their
implementations call functions that don't exist in tools (e.g. to
resolve qdev IDs). Move them out so that blockdev.c can be linked to
qemu-storage-daemon.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <20200224143008.13362-4-kwolf@redhat.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The bitmap code requires writing the 'file' child when the qcow2 driver
is reopened in read-write mode.
If the 'file' child is being reopened due to a permissions change, the
modification is commited yet when qcow2_reopen_commit is called. This
means that any attempt to write the 'file' child will end with EBADFD
as the original fd was already closed.
Moving bitmap reopening to the new callback which is called after
permission modifications are commited fixes this as the file descriptor
will be replaced with the correct one.
The above problem manifests itself when reopening 'qcow2' format layer
which uses a 'file-posix' file child which was opened with the
'auto-read-only' property set.
Signed-off-by: Peter Krempa <pkrempa@redhat.com>
Message-Id: <db118dbafe1955afbc0a18d3dd220931074ce349.1582893284.git.pkrempa@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
handle_alloc() reuses preallocated zero clusters. If anything goes
wrong during the data write, we do not change their L2 entry, so we
must not let qcow2_alloc_cluster_abort() free them.
Fixes: 8b24cd1415
Cc: qemu-stable@nongnu.org
Signed-off-by: Max Reitz <mreitz@redhat.com>
Message-Id: <20200225143130.111267-2-mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
After failover the Secondary side of replication shouldn't change state, because
it now functions as our primary disk.
In replication_start, replication_do_checkpoint, replication_stop, ignore
the request if current state is BLOCK_REPLICATION_DONE (sucessful failover) or
BLOCK_REPLICATION_FAILOVER (failover in progres i.e. currently merging active
and hidden images into the base image).
Signed-off-by: Lukas Straub <lukasstraub2@web.de>
Reviewed-by: Zhang Chen <chen.zhang@intel.com>
Acked-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
In currently implementation there will be a memory leak when
nbd_client_connect() returns error status. Here is an easy way to
reproduce:
1. run qemu-iotests as follow and check the result with asan:
./check -raw 143
Following is the asan output backtrack:
Direct leak of 40 byte(s) in 1 object(s) allocated from:
#0 0x7f629688a560 in calloc (/usr/lib64/libasan.so.3+0xc7560)
#1 0x7f6295e7e015 in g_malloc0 (/usr/lib64/libglib-2.0.so.0+0x50015)
#2 0x56281dab4642 in qobject_input_start_struct /mnt/sdb/qemu-4.2.0-rc0/qapi/qobject-input-visitor.c:295
#3 0x56281dab1a04 in visit_start_struct /mnt/sdb/qemu-4.2.0-rc0/qapi/qapi-visit-core.c:49
#4 0x56281dad1827 in visit_type_SocketAddress qapi/qapi-visit-sockets.c:386
#5 0x56281da8062f in nbd_config /mnt/sdb/qemu-4.2.0-rc0/block/nbd.c:1716
#6 0x56281da8062f in nbd_process_options /mnt/sdb/qemu-4.2.0-rc0/block/nbd.c:1829
#7 0x56281da8062f in nbd_open /mnt/sdb/qemu-4.2.0-rc0/block/nbd.c:1873
Direct leak of 15 byte(s) in 1 object(s) allocated from:
#0 0x7f629688a3a0 in malloc (/usr/lib64/libasan.so.3+0xc73a0)
#1 0x7f6295e7dfbd in g_malloc (/usr/lib64/libglib-2.0.so.0+0x4ffbd)
#2 0x7f6295e96ace in g_strdup (/usr/lib64/libglib-2.0.so.0+0x68ace)
#3 0x56281da804ac in nbd_process_options /mnt/sdb/qemu-4.2.0-rc0/block/nbd.c:1834
#4 0x56281da804ac in nbd_open /mnt/sdb/qemu-4.2.0-rc0/block/nbd.c:1873
Indirect leak of 24 byte(s) in 1 object(s) allocated from:
#0 0x7f629688a3a0 in malloc (/usr/lib64/libasan.so.3+0xc73a0)
#1 0x7f6295e7dfbd in g_malloc (/usr/lib64/libglib-2.0.so.0+0x4ffbd)
#2 0x7f6295e96ace in g_strdup (/usr/lib64/libglib-2.0.so.0+0x68ace)
#3 0x56281dab41a3 in qobject_input_type_str_keyval /mnt/sdb/qemu-4.2.0-rc0/qapi/qobject-input-visitor.c:536
#4 0x56281dab2ee9 in visit_type_str /mnt/sdb/qemu-4.2.0-rc0/qapi/qapi-visit-core.c:297
#5 0x56281dad0fa1 in visit_type_UnixSocketAddress_members qapi/qapi-visit-sockets.c:141
#6 0x56281dad17b6 in visit_type_SocketAddress_members qapi/qapi-visit-sockets.c:366
#7 0x56281dad186a in visit_type_SocketAddress qapi/qapi-visit-sockets.c:393
#8 0x56281da8062f in nbd_config /mnt/sdb/qemu-4.2.0-rc0/block/nbd.c:1716
#9 0x56281da8062f in nbd_process_options /mnt/sdb/qemu-4.2.0-rc0/block/nbd.c:1829
#10 0x56281da8062f in nbd_open /mnt/sdb/qemu-4.2.0-rc0/block/nbd.c:1873
Fixes: 8f071c9db5
Reported-by: Euler Robot <euler.robot@huawei.com>
Signed-off-by: Pan Nengyuan <pannengyuan@huawei.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Cc: qemu-stable <qemu-stable@nongnu.org>
Cc: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-Id: <1575517528-44312-3-git-send-email-pannengyuan@huawei.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Eric Blake <eblake@redhat.com>
The BDRVNBDState cleanup code is common in two places, add
nbd_clear_bdrvstate() function to do these cleanups.
Suggested-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Pan Nengyuan <pannengyuan@huawei.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-Id: <1575517528-44312-2-git-send-email-pannengyuan@huawei.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
[eblake: fix compilation error and commit message]
Signed-off-by: Eric Blake <eblake@redhat.com>
The NBD URI specification [1] states that only one leading slash at
the beginning of the URI path component is stripped, not all such
slashes. This becomes important to a patch I just proposed to nbdkit
[2], which would allow the exportname to select a file embedded within
an ext2 image: ext2fs demands an absolute pathname beginning with '/',
and because qemu was inadvertantly stripping it, my nbdkit patch had
to work around the behavior.
[1] https://github.com/NetworkBlockDevice/nbd/blob/master/doc/uri.md
[2] https://www.redhat.com/archives/libguestfs/2020-February/msg00109.html
Note that the qemu bug only affects handling of URIs such as
nbd://host:port//abs/path (where '/abs/path' should be the export
name); it is still possible to use --image-opts and pass the desired
export name with a leading slash directly through JSON even without
this patch.
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <20200212023101.1162686-1-eblake@redhat.com>
Reviewed-by: Ján Tomko <jtomko@redhat.com>
When printing the snapshot list (e.g. with qemu-img snapshot -l), the VM
size field is only seven characters wide. As of de38b5005e, this is
not necessarily sufficient: We generally print three digits, and this
may require a decimal point. Also, the unit field grew from something
as plain as "M" to " MiB". This means that number and unit may take up
eight characters in total; but we also want spaces in front.
Considering previously the maximum width was four characters and the
field width was chosen to be three characters wider, let us adjust the
field width to be eleven now.
Fixes: de38b5005e
Buglink: https://bugs.launchpad.net/qemu/+bug/1859989
Signed-off-by: Max Reitz <mreitz@redhat.com>
Message-Id: <20200117105859.241818-2-mreitz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
The generic fallback implementation effectively does the same.
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
Message-Id: <20200122164532.178040-5-mreitz@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
The generic fallback implementation effectively does the same.
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
Message-Id: <20200122164532.178040-4-mreitz@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
When nbd_close() is called from a coroutine, the connection_co never
gets to run, and thus nbd_teardown_connection() hangs.
This is because aio_co_enter() only puts the connection_co into the main
coroutine's wake-up queue, so this main coroutine needs to yield and
wait for connection_co to terminate.
Suggested-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
Message-Id: <20200122164532.178040-2-mreitz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
backup-top "supports" write-unchanged, by skipping CBW operation in
backup_top_co_pwritev. But it forgets to do the same in
backup_top_co_pwrite_zeroes, as well as declare support for
BDRV_REQ_WRITE_UNCHANGED.
Fix this, and, while being here, declare also support for flags
supported by source child.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-Id: <20200207161231.32707-1-vsementsov@virtuozzo.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
When initializing the LUKS header the size with default encryption
parameters will currently be 2068480 bytes. This is rounded up to
a multiple of the cluster size, 2081792, with 64k sectors. If the
end of the header is not the same as the end of the cluster we fill
the extra space with zeros. This was forgetting that not even the
space allocated for the header will be fully initialized, as we
only write key material for the first key slot. The space left
for the other 7 slots is never written to.
An optimization to the ref count checking code:
commit a5fff8d4b4 (refs/bisect/bad)
Author: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Date: Wed Feb 27 16:14:30 2019 +0300
qcow2-refcount: avoid eating RAM
made the assumption that every cluster which was allocated would
have at least some data written to it. This was violated by way
the LUKS header is only partially written, with much space simply
reserved for future use.
Depending on the cluster size this problem was masked by the
logic which wrote zeros between the end of the LUKS header and
the end of the cluster.
$ qemu-img create --object secret,id=cluster_encrypt0,data=123456 \
-f qcow2 -o cluster_size=2k,encrypt.iter-time=1,\
encrypt.format=luks,encrypt.key-secret=cluster_encrypt0 \
cluster_size_check.qcow2 100M
Formatting 'cluster_size_check.qcow2', fmt=qcow2 size=104857600
encrypt.format=luks encrypt.key-secret=cluster_encrypt0
encrypt.iter-time=1 cluster_size=2048 lazy_refcounts=off refcount_bits=16
$ qemu-img check --object secret,id=cluster_encrypt0,data=redhat \
'json:{"driver": "qcow2", "encrypt.format": "luks", \
"encrypt.key-secret": "cluster_encrypt0", \
"file.driver": "file", "file.filename": "cluster_size_check.qcow2"}'
ERROR: counting reference for region exceeding the end of the file by one cluster or more: offset 0x2000 size 0x1f9000
Leaked cluster 4 refcount=1 reference=0
...snip...
Leaked cluster 130 refcount=1 reference=0
1 errors were found on the image.
Data may be corrupted, or further writes to the image may corrupt it.
127 leaked clusters were found on the image.
This means waste of disk space, but no harm to data.
Image end offset: 268288
The problem only exists when the disk image is entirely empty. Writing
data to the disk image payload will solve the problem by causing the
end of the file to be extended further.
The change fixes it by ensuring that the entire allocated LUKS header
region is fully initialized with zeros. The qemu-img check will still
fail for any pre-existing disk images created prior to this change,
unless at least 1 byte of the payload is written to.
Fully writing zeros to the entire LUKS header is a good idea regardless
as it ensures that space has been allocated on the host filesystem (or
whatever block storage backend is used).
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Message-Id: <20200207135520.2669430-1-berrange@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
When a management application manages node names there's no reason to
recurse into backing images in the output of query-named-block-nodes.
Add a parameter to the command which will return just the top level
structs.
Signed-off-by: Peter Krempa <pkrempa@redhat.com>
Message-Id: <4470f8c779abc404dcf65e375db195cd91a80651.1579509782.git.pkrempa@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
[mreitz: Fixed coding style]
Signed-off-by: Max Reitz <mreitz@redhat.com>
Quorum is not a filter, for example because it cannot guarantee which of
its children will serve the next request. Thus, any of its children may
differ from the data visible to quorum's parents.
We have other filters with multiple children, but they differ in this
aspect:
- blkverify quits the whole qemu process if its children differ. As
such, we can always skip it when we want to skip it (as a filter node)
by going to any of its children. Both have the same data.
- replication generally serves requests from bs->file, so this is its
only actually filtered child.
- Block job filters currently only have one child, but they will
probably get more children in the future. Still, they will always
have only one actually filtered child.
Having "filters" as a dedicated node category only makes sense if you
can skip them by going to a one fixed child that always shows the same
data as the filter node. Quorum cannot fulfill this, so it is not a
filter.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-Id: <20200218103454.296704-13-mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
There is no guarantee that we can still replace the node we want to
replace at the end of the mirror job. Double-check by calling
bdrv_recurse_can_replace().
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-Id: <20200218103454.296704-12-mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
It no longer has any users.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-Id: <20200218103454.296704-11-mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-Id: <20200218103454.296704-8-mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Quorum cannot share WRITE or RESIZE on its children. Presumably, it
only does so because as a filter, it seemed intuitively correct to point
its .bdrv_child_perm to bdrv_filter_default_perm().
However, it is not really a filter, and bdrv_filter_default_perm() does
not work for it, so we have to provide a custom .bdrv_child_perm
implementation.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-Id: <20200218103454.296704-6-mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Fixes: 6663a0a337
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200218094402.26625-5-philmd@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
block_job_error_action() needs to know if reading from the top node or
writing to the base node failed so that it can set the right 'operation'
in the BLOCK_JOB_ERROR QMP event.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <20200214200812.28180-6-kwolf@redhat.com>
Reviewed-by: Ján Tomko <jtomko@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
commit_populate() is a very short function and only called in a single
place. Its return value doesn't tell us whether an error happened while
reading or writing, which would be necessary for sending the right data
in the BLOCK_JOB_ERROR QMP event.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <20200214200812.28180-5-kwolf@redhat.com>
Reviewed-by: Ján Tomko <jtomko@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The block_job_error_action() error call in the commit job gives the
on_err and is_read arguments in the wrong order. Fix this.
(Of course, hard-coded is_read = false is wrong, too, but that's a
separate problem for a separate patch.)
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <20200214200812.28180-4-kwolf@redhat.com>
Reviewed-by: Ján Tomko <jtomko@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The bytes_written variable is only ever written to, it serves no
purpose. This has actually been the case since the commit job was first
introduced in commit 747ff60263.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <20200214200812.28180-3-kwolf@redhat.com>
Reviewed-by: Ján Tomko <jtomko@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Fix warning reported by Clang static code analyzer:
CC block/qcow2-bitmap.o
block/qcow2-bitmap.c:650:5: warning: Value stored to 'ret' is never read
ret = -EINVAL;
^ ~~~~~~~
Fixes: 88ddffae8
Reported-by: Clang Static Analyzer
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200215161557.4077-2-philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Ján Tomko <jtomko@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
For external data file, cluster allocations return an offset in the data
file and are not refcounted. In this case, there is nothing to do for
qcow2_alloc_cluster_abort(). Freeing the same offset in the qcow2 file
is wrong and causes crashes in the better case or image corruption in
the worse case.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <20200211094900.17315-3-kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
In the case that update_refcount() frees a refcount block, it evicts it
from the metadata cache. Before doing so, however, it returns the
currently used refcount block to the cache because it might be the same.
Returning the refcount block early means that we need to reset
old_table_index so that we reload the refcount block in the next
iteration if it is actually still in use.
Fixes: f71c08ea8e
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <20200211094900.17315-2-kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Before this commit, BDRVVVFATState.qcow is unrefed in write_target_close
on closing backing bdrv of vvfat. However, qcow bdrv is opend as a child
of vvfat in enable_write_target() so it will be also unrefed on closing
vvfat itself. This causes use-after-free of qcow on freeing vvfat which
has backing bdrv and qcow bdrv as children in this order because
bdrv_close(vvfat) tries to free qcow bdrv after freeing backing bdrv
as QLIST_FOREACH_SAFE() loop keeps next pointer, but BdrvChild of qcow
is already freed in bdrv_close(backing bdrv).
Signed-off-by: Hikaru Nishida <hikarupsp@gmail.com>
Message-Id: <20200209175156.85748-1-hikarupsp@gmail.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
I/O requests to encrypted media should be aligned to the sector size
used by the underlying encryption method, not to BDRV_SECTOR_SIZE.
Fortunately this doesn't break anything at the moment because
both existing QCRYPTO_BLOCK_*_SECTOR_SIZE have the same value as
BDRV_SECTOR_SIZE.
The checks in qcow2_co_preadv_encrypted() are also unnecessary because
they are repeated immediately afterwards in qcow2_co_encdec().
Signed-off-by: Alberto Garcia <berto@igalia.com>
Message-Id: <20200213171646.15876-1-berto@igalia.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
mirror_wait_for_free_in_flight_slot() just picks a random operation to
wait for. However, when mirror_co_read() waits for free slots, its
MirrorOp is already in s->ops_in_flight, so if not enough slots are
immediately available, an operation can end up waiting for itself to
complete, which results in a hang.
Fix this by passing the current MirrorOp and skipping this operation
when picking an operation to wait for.
Fixes: https://bugzilla.redhat.com/show_bug.cgi?id=1794692
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
If a coroutine is launched, but the coroutine pointer isn't stored
anywhere, debugging any problems inside the coroutine is quite hard.
Let's store the coroutine pointer of a mirror operation in MirrorOp to
have it available in the debugger.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Commit 7a3f542fbd "block/io: refactor padding" occasionally dropped
aligning for zero-length request: bdrv_init_padding() blindly return
false if bytes == 0, like there is nothing to align.
This leads the following command to crash:
./qemu-io --image-opts -c 'write 1 0' \
driver=blkdebug,align=512,image.driver=null-co,image.size=512
>> qemu-io: block/io.c:1955: bdrv_aligned_pwritev: Assertion
`(offset & (align - 1)) == 0' failed.
>> Aborted (core dumped)
Prior to 7a3f542fbd we does aligning of such zero requests. Instead of
recovering this behavior let's just do nothing on such requests as it
is useless.
Note that driver may have special meaning of zero-length reqeusts, like
qcow2_co_pwritev_compressed_part, so we can't skip any zero-length
operation. But for unaligned ones, we can't pass it to driver anyway.
This commit also fixes crash in iotest 80 running with -nocache:
./check -nocache -qcow2 80
which crashes on same assertion due to trying to read empty extra data
in qcow2_do_read_snapshots().
Cc: qemu-stable@nongnu.org # v4.2
Fixes: 7a3f542fbd
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Message-id: 20200206164245.17781-1-vsementsov@virtuozzo.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
We can't access top after call bdrv_backup_top_drop, as it is already
freed at this time.
Also, no needs to unref target child by hand, it will be unrefed on
bdrv_close() automatically.
So, just do bdrv_backup_top_drop if append succeed and one bdrv_unref
otherwise.
Note, that in !appended case bdrv_unref(top) moved into drained section
on source. It doesn't really matter, but just for code simplicity.
Fixes: 7df7868b96
Cc: qemu-stable@nongnu.org # v4.2.0
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Message-id: 20200121142802.21467-2-vsementsov@virtuozzo.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
qemu-img's convert_co_copy_range() operates at the sector level and
block_copy() operates at the cluster level so this condition is always
true, but it is not necessary to restrict this here, so let's leave it
to the driver implementation return an error if there is any.
Signed-off-by: Alberto Garcia <berto@igalia.com>
Message-id: a4264aaee656910c84161a2965f7a501437379ca.1579374329.git.berto@igalia.com
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
When updating an L1 entry the qcow2 driver writes a (512-byte) sector
worth of data to avoid a read-modify-write cycle. Instead of always
writing 512 bytes we should follow the alignment requirements of the
storage backend.
(the only exception is when the alignment is larger than the cluster
size because then we could be overwriting data after the L1 table)
Signed-off-by: Alberto Garcia <berto@igalia.com>
Message-id: 71f34d4ae4b367b32fb36134acbf4f4f7ee681f4.1579374329.git.berto@igalia.com
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
qcow2_alloc_cluster_offset() and qcow2_get_cluster_offset() always
return offsets that are cluster-aligned so don't just check that they
are sector-aligned.
The check in qcow2_co_preadv_task() is also replaced by an assertion
for the same reason.
Signed-off-by: Alberto Garcia <berto@igalia.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Message-id: 558ba339965f858bede4c73ce3f50f0c0493597d.1579374329.git.berto@igalia.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
The L1 table is read from disk using the byte-based bdrv_pread() and
is never accessed beyond its last element, so there's no need to
allocate more memory than that.
Signed-off-by: Alberto Garcia <berto@igalia.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Message-id: b2e27214ec7b03a585931bcf383ee1ac3a641a10.1579374329.git.berto@igalia.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
This is a bit more efficient than having to allocate and free memory
for each item.
The default size (60) is enough for all the existing incompatible
features or the "Unknown incompatible feature" message.
Suggested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Alberto Garcia <berto@igalia.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20200115135626.19442-1-berto@igalia.com
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
The standard cluster descriptor in L2 table entries has a field to
store the host cluster offset. When we need to get that offset from an
entry we use L2E_OFFSET_MASK to ensure that we only use the bits that
belong to that field.
But while that mask is used every time we read from an L2 entry, it
is never used when we write to it. Due to the QCOW_MAX_CLUSTER_OFFSET
limit set in the cluster allocation code QEMU can never produce
offsets that don't fit in that field so any such offset would indicate
a bug in QEMU.
Compressed cluster descriptors contain two fields (host cluster offset
and size of the compressed data) and the situation with them is
similar. In this case the masks are not constant but are stored in the
csize_mask and cluster_offset_mask fields of BDRVQcow2State.
Signed-off-by: Alberto Garcia <berto@igalia.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-id: 20200113161146.20099-1-berto@igalia.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
Aborts when sqe fails to be set as sqes cannot be returned to the
ring. Adds slow path for short reads for older kernels
Signed-off-by: Aarushi Mehta <mehta.aaru20@gmail.com>
Acked-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 20200120141858.587874-5-stefanha@redhat.com
Message-Id: <20200120141858.587874-5-stefanha@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
bdrv_mark_request_serialising is writing the overlap_offset and
overlap_bytes fields of BdrvTrackedRequest. Take bs->reqs_lock
for the whole duration of it, and not just when waiting for
serialising requests, so that tracked_request_overlaps does not
look at a half-updated request.
The new code does not unlock/relock around retries. This is unnecessary
because a retry is always preceded by a CoQueue wait, which already
releases and reacquires bs->reqs_lock.
Reported-by: Peter Lieven <pl@kamp.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-id: 1578495356-46219-4-git-send-email-pbonzini@redhat.com
Message-Id: <1578495356-46219-4-git-send-email-pbonzini@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Marking without waiting would not result in actual serialising behavior.
Thus, make a call bdrv_mark_request_serialising sufficient for
serialisation to happen.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-id: 1578495356-46219-3-git-send-email-pbonzini@redhat.com
Message-Id: <1578495356-46219-3-git-send-email-pbonzini@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
It is unused since commit 00e30f0 ("block/backup: use backup-top instead
of write notifiers", 2019-10-01), drop it to simplify the code.
While at it, drop redundant assertions on flags.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-id: 1578495356-46219-2-git-send-email-pbonzini@redhat.com
Message-Id: <1578495356-46219-2-git-send-email-pbonzini@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
In iscsi_co_block_status(), we may have received num_descriptors == 0
from the iscsi server. Therefore, we can't unconditionally access
lbas->descriptors[0]. Add the missing check.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Felipe Franciosi <felipe@nutanix.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Peter Lieven <pl@kamp.de>
When querying an iSCSI server for the provisioning status of blocks (via
GET LBA STATUS), Qemu only validates that the response descriptor zero's
LBA matches the one requested. Given the SCSI spec allows servers to
respond with the status of blocks beyond the end of the LUN, Qemu may
have its heap corrupted by clearing/setting too many bits at the end of
its allocmap for the LUN.
A malicious guest in control of the iSCSI server could carefully program
Qemu's heap (by selectively setting the bitmap) and then smash it.
This limits the number of bits that iscsi_co_block_status() will try to
update in the allocmap so it can't overflow the bitmap.
Fixes: CVE-2020-1711
Cc: qemu-stable@nongnu.org
Signed-off-by: Felipe Franciosi <felipe@nutanix.com>
Signed-off-by: Peter Turschmid <peter.turschm@nutanix.com>
Signed-off-by: Raphael Norwitz <raphael.norwitz@nutanix.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
bdrv_open_driver() allocates bs->opaque according to drv->instance_size.
There is no need to allocate it and overwrite opaque in
bdrv_backup_top_append().
Reproducer:
$ QTEST_QEMU_BINARY=./x86_64-softmmu/qemu-system-x86_64 valgrind -q --leak-check=full tests/test-replication -p /replication/secondary/start
==29792== 24 bytes in 1 blocks are definitely lost in loss record 52 of 226
==29792== at 0x483AB1A: calloc (vg_replace_malloc.c:762)
==29792== by 0x4B07CE0: g_malloc0 (in /usr/lib64/libglib-2.0.so.0.6000.7)
==29792== by 0x12BAB9: bdrv_open_driver (block.c:1289)
==29792== by 0x12BEA9: bdrv_new_open_driver (block.c:1359)
==29792== by 0x1D15CB: bdrv_backup_top_append (backup-top.c:190)
==29792== by 0x1CC11A: backup_job_create (backup.c:439)
==29792== by 0x1CD542: replication_start (replication.c:544)
==29792== by 0x1401B9: replication_start_all (replication.c:52)
==29792== by 0x128B50: test_secondary_start (test-replication.c:427)
...
Fixes: 7df7868b96 ("block: introduce backup-top filter driver")
Signed-off-by: Eiichi Tsukata <devel@etsukata.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
All paths that lead to bdrv_backup_top_drop(), except for the call
from backup_clean(), imply that the BDS AioContext has already been
acquired, so doing it there too can potentially lead to QEMU hanging
on AIO_WAIT_WHILE().
An easy way to trigger this situation is by issuing a two actions
transaction, with a proper and a bogus blockdev-backup, so the second
one will trigger a rollback. This will trigger a hang with an stack
trace like this one:
#0 0x00007fb680c75016 in __GI_ppoll (fds=0x55e74580f7c0, nfds=1, timeout=<optimized out>,
timeout@entry=0x0, sigmask=sigmask@entry=0x0) at ../sysdeps/unix/sysv/linux/ppoll.c:39
#1 0x000055e743386e09 in ppoll (__ss=0x0, __timeout=0x0, __nfds=<optimized out>, __fds=<optimized out>)
at /usr/include/bits/poll2.h:77
#2 0x000055e743386e09 in qemu_poll_ns
(fds=<optimized out>, nfds=<optimized out>, timeout=<optimized out>) at util/qemu-timer.c:336
#3 0x000055e743388dc4 in aio_poll (ctx=0x55e7458925d0, blocking=blocking@entry=true)
at util/aio-posix.c:669
#4 0x000055e743305dea in bdrv_flush (bs=bs@entry=0x55e74593c0d0) at block/io.c:2878
#5 0x000055e7432be58e in bdrv_close (bs=0x55e74593c0d0) at block.c:4017
#6 0x000055e7432be58e in bdrv_delete (bs=<optimized out>) at block.c:4262
#7 0x000055e7432be58e in bdrv_unref (bs=bs@entry=0x55e74593c0d0) at block.c:5644
#8 0x000055e743316b9b in bdrv_backup_top_drop (bs=bs@entry=0x55e74593c0d0) at block/backup-top.c:273
#9 0x000055e74331461f in backup_job_create
(job_id=0x0, bs=bs@entry=0x55e7458d5820, target=target@entry=0x55e74589f640, speed=0, sync_mode=MIRROR_SYNC_MODE_FULL, sync_bitmap=sync_bitmap@entry=0x0, bitmap_mode=BITMAP_SYNC_MODE_ON_SUCCESS, compress=false, filter_node_name=0x0, on_source_error=BLOCKDEV_ON_ERROR_REPORT, on_target_error=BLOCKDEV_ON_ERROR_REPORT, creation_flags=0, cb=0x0, opaque=0x0, txn=0x0, errp=0x7ffddfd1efb0) at block/backup.c:478
#10 0x000055e74315bc52 in do_backup_common
(backup=backup@entry=0x55e746c066d0, bs=bs@entry=0x55e7458d5820, target_bs=target_bs@entry=0x55e74589f640, aio_context=aio_context@entry=0x55e7458a91e0, txn=txn@entry=0x0, errp=errp@entry=0x7ffddfd1efb0)
at blockdev.c:3580
#11 0x000055e74315c37c in do_blockdev_backup
(backup=backup@entry=0x55e746c066d0, txn=0x0, errp=errp@entry=0x7ffddfd1efb0)
at /usr/src/debug/qemu-kvm-4.2.0-2.module+el8.2.0+5135+ed3b2489.x86_64/./qapi/qapi-types-block-core.h:1492
#12 0x000055e74315c449 in blockdev_backup_prepare (common=0x55e746a8de90, errp=0x7ffddfd1f018)
at blockdev.c:1885
#13 0x000055e743160152 in qmp_transaction
(dev_list=<optimized out>, has_props=<optimized out>, props=0x55e7467fe2c0, errp=errp@entry=0x7ffddfd1f088) at blockdev.c:2340
#14 0x000055e743287ff5 in qmp_marshal_transaction
(args=<optimized out>, ret=<optimized out>, errp=0x7ffddfd1f0f8)
at qapi/qapi-commands-transaction.c:44
#15 0x000055e74333de6c in do_qmp_dispatch
(errp=0x7ffddfd1f0f0, allow_oob=<optimized out>, request=<optimized out>, cmds=0x55e743c28d60 <qmp_commands>) at qapi/qmp-dispatch.c:132
#16 0x000055e74333de6c in qmp_dispatch
(cmds=0x55e743c28d60 <qmp_commands>, request=<optimized out>, allow_oob=<optimized out>)
at qapi/qmp-dispatch.c:175
#17 0x000055e74325c061 in monitor_qmp_dispatch (mon=0x55e745908030, req=<optimized out>)
at monitor/qmp.c:145
#18 0x000055e74325c6fa in monitor_qmp_bh_dispatcher (data=<optimized out>) at monitor/qmp.c:234
#19 0x000055e743385866 in aio_bh_call (bh=0x55e745807ae0) at util/async.c:117
#20 0x000055e743385866 in aio_bh_poll (ctx=ctx@entry=0x55e7458067a0) at util/async.c:117
#21 0x000055e743388c54 in aio_dispatch (ctx=0x55e7458067a0) at util/aio-posix.c:459
#22 0x000055e743385742 in aio_ctx_dispatch
(source=<optimized out>, callback=<optimized out>, user_data=<optimized out>) at util/async.c:260
#23 0x00007fb68543e67d in g_main_dispatch (context=0x55e745893a40) at gmain.c:3176
#24 0x00007fb68543e67d in g_main_context_dispatch (context=context@entry=0x55e745893a40) at gmain.c:3829
#25 0x000055e743387d08 in glib_pollfds_poll () at util/main-loop.c:219
#26 0x000055e743387d08 in os_host_main_loop_wait (timeout=<optimized out>) at util/main-loop.c:242
#27 0x000055e743387d08 in main_loop_wait (nonblocking=<optimized out>) at util/main-loop.c:518
#28 0x000055e74316a3c1 in main_loop () at vl.c:1828
#29 0x000055e743016a72 in main (argc=<optimized out>, argv=<optimized out>, envp=<optimized out>)
at vl.c:4504
Fix this by not acquiring the AioContext there, and ensuring all paths
leading to it have it already acquired (backup_clean()).
RHBZ: https://bugzilla.redhat.com/show_bug.cgi?id=1782111
Signed-off-by: Sergio Lopez <slp@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Since commit 6040aedddb "virtio-blk:
make queue size configurable",if the user set the queue size to
more than 128 ,it will not take effect. That's because linux aio's
maximum outstanding requests at a time is always less than or equal
to 128.
This patch simply increase MAX_EVENTS to a larger hardcoded value of
1024 as a shortterm fix.
Signed-off-by: wangyong <wang.yongD@h3c.com>
Message-id: faa5781afd354a96a0be152b288f636f@h3c.com
Message-Id: <faa5781afd354a96a0be152b288f636f@h3c.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
When dropping backup-top, we need to drain the node before freeing the
BlockCopyState. Otherwise, requests may still be in flight and then the
assertion in shres_destroy() will fail.
(This becomes visible in intermittent failure of 056.)
Cc: qemu-stable@nongnu.org
Signed-off-by: Max Reitz <mreitz@redhat.com>
Message-id: 20191219182638.104621-1-mreitz@redhat.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
QEMU currently supports writing compressed data of the size equal to
one cluster. This patch allows writing QCOW2 compressed data that
exceed one cluster. Now, we split buffered data into separate clusters
and write them compressed using the block/aio_task API.
Suggested-by: Pavel Butsykin <pbutsykin@virtuozzo.com>
Suggested-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Signed-off-by: Andrey Shinkevich <andrey.shinkevich@virtuozzo.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Message-id: 1575288906-551879-3-git-send-email-andrey.shinkevich@virtuozzo.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
Allow writing all the data compressed through the filter driver.
The written data will be aligned by the cluster size.
Based on the QEMU current implementation, that data can be written to
unallocated clusters only. May be used for a backup job.
Suggested-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Andrey Shinkevich <andrey.shinkevich@virtuozzo.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-id: 1575288906-551879-2-git-send-email-andrey.shinkevich@virtuozzo.com
[mreitz: Replace NULL bdrv_get_format_name() by "(no format)"]
Signed-off-by: Max Reitz <mreitz@redhat.com>
qcow2_can_store_new_dirty_bitmap works wrong, as it considers only
bitmaps already stored in the qcow2 image and ignores persistent
BdrvDirtyBitmap objects.
So, let's instead count persistent BdrvDirtyBitmaps. We load all qcow2
bitmaps on open, so there should not be any bitmap in the image for
which we don't have BdrvDirtyBitmaps version. If it is - it's a kind of
corruption, and no reason to check for corruptions here (open() and
close() are better places for it).
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-id: 20191014115126.15360-2-vsementsov@virtuozzo.com
Reviewed-by: Max Reitz <mreitz@redhat.com>
Cc: qemu-stable@nongnu.org
Signed-off-by: Max Reitz <mreitz@redhat.com>
This avoid a memory leak when qom-set is called to set throttle_group
limits, here is an easy way to reproduce:
1. run qemu-iotests as follow and check the result with asan:
./check -qcow2 184
Following is the asan output backtrack:
Direct leak of 912 byte(s) in 3 object(s) allocated from:
#0 0xffff8d7ab3c3 in __interceptor_calloc (/lib64/libasan.so.4+0xd33c3)
#1 0xffff8d4c31cb in g_malloc0 (/lib64/libglib-2.0.so.0+0x571cb)
#2 0x190c857 in qobject_input_start_struct /mnt/sdc/qemu-master/qemu-4.2.0-rc0/qapi/qobject-input-visitor.c:295
#3 0x19070df in visit_start_struct /mnt/sdc/qemu-master/qemu-4.2.0-rc0/qapi/qapi-visit-core.c:49
#4 0x1948b87 in visit_type_ThrottleLimits qapi/qapi-visit-block-core.c:3759
#5 0x17e4aa3 in throttle_group_set_limits /mnt/sdc/qemu-master/qemu-4.2.0-rc0/block/throttle-groups.c:900
#6 0x1650eff in object_property_set /mnt/sdc/qemu-master/qemu-4.2.0-rc0/qom/object.c:1272
#7 0x1658517 in object_property_set_qobject /mnt/sdc/qemu-master/qemu-4.2.0-rc0/qom/qom-qobject.c:26
#8 0x15880bb in qmp_qom_set /mnt/sdc/qemu-master/qemu-4.2.0-rc0/qom/qom-qmp-cmds.c:74
#9 0x157e3e3 in qmp_marshal_qom_set qapi/qapi-commands-qom.c:154
Reported-by: Euler Robot <euler.robot@huawei.com>
Signed-off-by: PanNengyuan <pannengyuan@huawei.com>
Message-id: 1574835614-42028-1-git-send-email-pannengyuan@huawei.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
Sometimes it is useful to be able to add a node to the block graph that
takes or unshare a certain set of permissions for debugging purposes.
This patch adds this capability to blkdebug.
(Note that you cannot make blkdebug release or share permissions that it
needs to take or cannot share, because this might result in assertion
failures in the block layer. But if the blkdebug node has no parents,
it will not take any permissions and share everything by default, so you
can then freely choose what permissions to take and share.)
Signed-off-by: Max Reitz <mreitz@redhat.com>
Message-id: 20191108123455.39445-4-mreitz@redhat.com
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
- qemu-img: fix info --backing-chain --image-opts
- Error out on image creation with conflicting size options
- Fix external snapshot with VM state
- hmp: Allow using qdev ID for qemu-io command
- Misc code cleanup
- Many iotests improvements
-----BEGIN PGP SIGNATURE-----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=laVP
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/kevin/tags/for-upstream' into staging
Block layer patches:
- qemu-img: fix info --backing-chain --image-opts
- Error out on image creation with conflicting size options
- Fix external snapshot with VM state
- hmp: Allow using qdev ID for qemu-io command
- Misc code cleanup
- Many iotests improvements
# gpg: Signature made Thu 19 Dec 2019 17:23:11 GMT
# gpg: using RSA key 7F09B272C88F2FD6
# gpg: Good signature from "Kevin Wolf <kwolf@redhat.com>" [full]
# Primary key fingerprint: DC3D EB15 9A9A F95D 3D74 56FE 7F09 B272 C88F 2FD6
* remotes/kevin/tags/for-upstream: (30 commits)
iotests: Test external snapshot with VM state
hmp: Allow using qdev ID for qemu-io command
block: Activate recursively even for already active nodes
iotests: 211: Remove duplication with VM.blockdev_create()
iotests: 207: Remove duplication with VM.blockdev_create()
iotests: 266: Convert to VM.blockdev_create()
iotests: 237: Convert to VM.blockdev_create()
iotests: 213: Convert to VM.blockdev_create()
iotests: 212: Convert to VM.blockdev_create()
iotests: 210: Convert to VM.blockdev_create()
iotests: 206: Convert to VM.blockdev_create()
iotests: 255: Drop blockdev_create()
iotests: Create VM.blockdev_create()
qcow2: Move error check of local_err near its assignment
iotests: Fix IMGOPTSSYNTAX for nbd
iotests/273: Filter format-specific information
iotests: Add more "_require_drivers" checks to the shell-based tests
MAINTAINERS: fix qcow2-bitmap.c under Dirty Bitmaps header
qcow2: Use offset_into_cluster()
iotests: Support job-complete in run_job()
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The local_err check outside of the if block was necessary
when it was introduced in commit d1258dd0c8 because it needed to be
executed even if qcow2_load_autoloading_dirty_bitmaps() returned false.
After some modifications that all required the error check to remain
where it is, commit 9c98f145df finally moved the
qcow2_load_dirty_bitmaps() call into the if block, so now the error
check should be there, too.
Signed-off-by: Guoyi Tu <tu.guoyi@h3c.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
There's a couple of places left in the qcow2 code that still do the
calculation manually, so let's replace them.
Signed-off-by: Alberto Garcia <berto@igalia.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
In the common case, qcow2_co_pwrite_zeroes() already only modifies
metadata case, so we're fine with or without BDRV_REQ_NO_FALLBACK set.
The only exception is when using an external data file, where the
request is passed down to the block driver of the external data file. We
are forwarding the BDRV_REQ_NO_FALLBACK flag there, though, so this is
fine, too.
Declare the flag supported therefore.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Alberto Garcia <berto@igalia.com>
All callers of nbd_iter_channel_error() pass the address of a
local_err variable, and only call this function if an error has
already occurred, using this function to propagate that error.
This is already implied by its name (local_err instead of the classic
errp), but it is worth additionally stressing this by adding an
assertion to make it part of the function contract.
The local_err parameter is not here to return information about
nbd_iter_channel_error failure. Instead it's assumed to be filled when
passed to the function. This is already stressed by its name
(local_err, instead of classic errp). Stress it additionally by
assertion.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-Id: <20191205174635.18758-22-vsementsov@virtuozzo.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Eric Blake <eblake@Redhat.com>
Message-Id: <20191205174635.18758-11-vsementsov@virtuozzo.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Here is double bug:
First, return error but not set errp. This may lead to:
qmp block-dirty-bitmap-remove may report success when actually failed
block-dirty-bitmap-remove used in a transaction will crash, as
qmp_transaction will think that it returned success and will call
block_dirty_bitmap_remove_commit which will crash, as state->bitmap is
NULL
Second (like in anecdote), this case is not an error at all. As it is
documented in the comment above bdrv_co_remove_persistent_dirty_bitmap
definition, absence of bitmap is not an error, and similar case handled
at start of qcow2_co_remove_persistent_dirty_bitmap, it returns 0 when
there is no bitmaps at all.
But when there are some bitmaps, but not the requested one, it return
error with errp unset.
Fix that.
Trigger:
1. create persistent bitmap A
2. shutdown vm (bitmap A is synced)
3. start vm
4. create persistent bitmap B
5. remove bitmap B - it fails (and crashes if in transaction)
Potential workaround (rather invasive to ask clients to implement it):
1. create persistent bitmap A
2. shutdown vm
3. start vm
4. create persistent bitmap B
5. remember, that we want to remove bitmap B after vm shutdown
...
some other operations
...
6. vm shutdown
7. start vm in stopped mode, and remove all bitmaps marked for removing
8. stop vm
Fixes: b56a1e3175
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-Id: <20191205193049.30666-1-vsementsov@virtuozzo.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
[eblake: commit message tweaks]
Signed-off-by: Eric Blake <eblake@redhat.com>
raw_aio_attach_aio_context() passes uninitialized Error *local_err by
reference to laio_init() via aio_setup_linux_aio(). When laio_init()
fails, it passes it on to error_setg_errno(), tripping error_setv()'s
assertion unless @local_err is null by dumb luck.
Fix by initializing @local_err properly.
Fixes: ed6e216171
Cc: Nishanth Aravamudan <naravamudan@digitalocean.com>
Cc: Stefan Hajnoczi <stefanha@redhat.com>
Cc: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20191130194240.10517-4-armbru@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Fix bitmap migration with dirty-bitmaps capability enabled and shared
storage. We should ignore IN_USE bitmaps in the image on target, when
migrating bitmaps through migration channel, see new comment below.
Fixes: 74da6b9435
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-id: 20191125125229.13531-2-vsementsov@virtuozzo.com
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
Qemu as server currently won't accept export names larger than 256
bytes, nor create dirty bitmap names longer than 1023 bytes, so most
uses of qemu as client or server have no reason to get anywhere near
the NBD spec maximum of a 4k limit per string.
However, we weren't actually enforcing things, ignoring when the
remote side violates the protocol on input, and also having several
code paths where we send oversize strings on output (for example,
qemu-nbd --description could easily send more than 4k). Tighten
things up as follows:
client:
- Perform bounds check on export name and dirty bitmap request prior
to handing it to server
- Validate that copied server replies are not too long (ignoring
NBD_INFO_* replies that are not copied is not too bad)
server:
- Perform bounds check on export name and description prior to
advertising it to client
- Reject client name or metadata query that is too long
- Adjust things to allow full 4k name limit rather than previous
256 byte limit
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <20191114024635.11363-4-eblake@redhat.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
We document that for qcow2 persistent bitmaps, the name cannot exceed
1023 bytes. It is inconsistent if transient bitmaps do not have to
abide by the same limit, and it is unlikely that any existing client
even cares about using bitmap names this long. It's time to codify
that ALL bitmaps managed by qemu (whether persistent in qcow2 or not)
have a documented maximum length.
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <20191114024635.11363-3-eblake@redhat.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
There are two issues in In check_constraints_on_bitmap(),
1) The sanity check on the granularity will cause uint64_t
integer left-shift overflow when cluster_size is 2M and the
granularity is BIGGER than 32K.
2) The way to calculate image size that the maximum bitmap
supported can map to is a bit incorrect.
This patch fix it by add a helper function to calculate the
number of bytes needed by a normal bitmap in image and compare
it to the maximum bitmap bytes supported by qemu.
Fixes: 5f72826e7f
Signed-off-by: Guoyi Tu <tu.guoyi@h3c.com>
Message-id: 4ba40cd1e7ee4a708b40899952e49f22@h3c.com
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Cc: qemu-stable@nongnu.org
Signed-off-by: Max Reitz <mreitz@redhat.com>
The XFS kernel driver has a bug that may cause data corruption for qcow2
images as of qemu commit c8bb23cbdb. We can work around it by
treating post-EOF fallocates as serializing up until infinity (INT64_MAX
in practice).
Cc: qemu-stable@nongnu.org
Signed-off-by: Max Reitz <mreitz@redhat.com>
Message-id: 20191101152510.11719-4-mreitz@redhat.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
