The new migrate_send_rp_req_pages_pending() call should greatly improve
destination responsiveness because it will resync faulted address after
postcopy recovery. However it is also the 1st place to initiate the page
request from the main thread.
One thing is overlooked on that migrate_send_rp_message_req_pages() is not
designed to be thread-safe. So if we wake the fault thread before syncing all
the faulted pages in the main thread, it means they can race.
Postpone the wake up operation after the sync of faulted addresses.
Fixes: 0c26781c09 ("migration: Sync requested pages after postcopy recovery")
Tested-by: Christian Schoenebeck <qemu_oss@crudebyte.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20201102153010.11979-3-peterx@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
When postcopy recover happens, we need to reset last_rb after each return of
postcopy_pause_fault_thread() because that means we just got the postcopy
migration continued.
Unify this reset to the place right before we want to kick the fault thread
again, when we get the command MIG_CMD_POSTCOPY_RESUME from source.
This is actually more than that - because the main thread on destination will
now be able to call migrate_send_rp_req_pages_pending() too, so the fault
thread is not the only user of last_rb now. Move the reset earlier will allow
the first call to migrate_send_rp_req_pages_pending() to use the reset value
even if called from the main thread.
(NOTE: this is not a real fix to 0c26781c09 mentioned below, however it is just
a mark that when picking up 0c26781c09 we'd better have this one too; the real
fix will come later)
Fixes: 0c26781c09 ("migration: Sync requested pages after postcopy recovery")
Tested-by: Christian Schoenebeck <qemu_oss@crudebyte.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20201102153010.11979-2-peterx@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
We synchronize the requested pages right after a postcopy recovery happens.
This helps to synchronize the prioritized pages on source so that the faulted
threads can be served faster.
Reported-by: Xiaohui Li <xiaohli@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20201021212721.440373-5-peterx@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Bihong Yu <yubihong@huawei.com>
Reviewed-by: Chuan Zheng <zhengchuan@huawei.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <1603163448-27122-7-git-send-email-yubihong@huawei.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Bihong Yu <yubihong@huawei.com>
Reviewed-by: Chuan Zheng <zhengchuan@huawei.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <1603163448-27122-4-git-send-email-yubihong@huawei.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Restricting xen-set-global-dirty-log and xen-load-devices-state
commands migration.json pulls slightly less QAPI-generated code
into user-mode and tools.
Acked-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20201012121536.3381997-6-philmd@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Non-empty record/replay queue prevents saving and loading the VM state,
because it includes pending bottom halves and block coroutines.
But when the new VM state is loaded, we don't have to preserve the consistency
of the current state anymore. Therefore this patch just flushes the queue
allowing the coroutines to finish and removes checking for empty rr queue
for load_snapshot function.
Signed-off-by: Pavel Dovgalyuk <Pavel.Dovgalyuk@ispras.ru>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <160174521762.12451.15752448887893855757.stgit@pasha-ThinkPad-X280>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Saving icount as a parameters of the snapshot allows navigation between
them in the execution replay scenario.
This information can be used for finding a specific snapshot for proceeding
the recorded execution to the specific moment of the time.
E.g., 'reverse step' action (introduced in one of the following patches)
needs to load the nearest snapshot which is prior to the current moment
of time.
This patch also updates snapshot test which verifies qemu monitor output.
Signed-off-by: Pavel Dovgalyuk <Pavel.Dovgalyuk@ispras.ru>
Acked-by: Markus Armbruster <armbru@redhat.com>
Acked-by: Kevin Wolf <kwolf@redhat.com>
--
v4 changes:
- squashed format update with test output update
v7 changes:
- introduced the spaces between the fields in snapshot info output
- updated the test to match new field widths
Message-Id: <160174518865.12451.14327573383978752463.stgit@pasha-ThinkPad-X280>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When running the xen-save-devices-state QMP command, if the filename
already exists it will be truncated before dumping the devices' state
into it.
Signed-off-by: Dov Murik <dovmurik@linux.vnet.ibm.com>
Message-Id: <20200921094830.114028-1-dovmurik@linux.vnet.ibm.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
I found that there are many spelling errors in the comments of qemu,
so I used the spellcheck tool to check the spelling errors
and finally found some spelling errors in the migration folder.
Signed-off-by: zhaolichang <zhaolichang@huawei.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20200917075029.313-3-zhaolichang@huawei.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
With blockdev, a BlockDriverState may not have a device name,
so using a node name is required as an alternative.
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Message-Id: <20200827111606.1408275-2-berrange@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
First, if only bitmaps postcopy is enabled (and not ram postcopy)
postcopy_pause_incoming crashes on an assertion
assert(mis->to_src_file).
And anyway, bitmaps postcopy is not prepared to be somehow recovered.
The original idea instead is that if bitmaps postcopy failed, we just
lose some bitmaps, which is not critical. So, on failure we just need
to remove unfinished bitmaps and guest should continue execution on
destination.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Andrey Shinkevich <andrey.shinkevich@virtuozzo.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <20200727194236.19551-18-vsementsov@virtuozzo.com>
Signed-off-by: Eric Blake <eblake@redhat.com>
qemu_fclose() could return error, f.e. if bdrv_co_flush() will return
the error.
This validation will become more important once we will start waiting of
asynchronous IO operations, started from bdrv_write_vmstate(), which are
coming soon.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Reviewed-by: "Dr. David Alan Gilbert" <dgilbert@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
CC: Kevin Wolf <kwolf@redhat.com>
CC: Max Reitz <mreitz@redhat.com>
CC: Stefan Hajnoczi <stefanha@redhat.com>
CC: Fam Zheng <fam@euphon.net>
CC: Juan Quintela <quintela@redhat.com>
CC: Denis Plotnikov <dplotnikov@virtuozzo.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
COLO will copy all memory in a RAM block, disable discarding of RAM.
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Tested-by: Lukas Straub <lukasstraub2@web.de>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Hailiang Zhang <zhang.zhanghailiang@huawei.com>
Cc: Juan Quintela <quintela@redhat.com>
Cc: "Dr. David Alan Gilbert" <dgilbert@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20200626072248.78761-10-david@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This code is not related to hardware emulation.
Move it under accel/ with the other hypervisors.
Reviewed-by: Paul Durrant <paul@xen.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200508100222.7112-1-philmd@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
'list' forgot to free at the end of dump_vmstate_json_to_file(), although it's called only once, but seems like a clean code.
Fix the leak as follow:
Direct leak of 16 byte(s) in 1 object(s) allocated from:
#0 0x7fb946abd768 in __interceptor_malloc (/lib64/libasan.so.5+0xef768)
#1 0x7fb945eca445 in g_malloc (/lib64/libglib-2.0.so.0+0x52445)
#2 0x7fb945ee2066 in g_slice_alloc (/lib64/libglib-2.0.so.0+0x6a066)
#3 0x7fb945ee3139 in g_slist_prepend (/lib64/libglib-2.0.so.0+0x6b139)
#4 0x5585db591581 in object_class_get_list_tramp /mnt/sdb/qemu-new/qemu/qom/object.c:1084
#5 0x5585db590f66 in object_class_foreach_tramp /mnt/sdb/qemu-new/qemu/qom/object.c:1028
#6 0x7fb945eb35f7 in g_hash_table_foreach (/lib64/libglib-2.0.so.0+0x3b5f7)
#7 0x5585db59110c in object_class_foreach /mnt/sdb/qemu-new/qemu/qom/object.c:1038
#8 0x5585db5916b6 in object_class_get_list /mnt/sdb/qemu-new/qemu/qom/object.c:1092
#9 0x5585db335ca0 in dump_vmstate_json_to_file /mnt/sdb/qemu-new/qemu/migration/savevm.c:638
#10 0x5585daa5bcbf in main /mnt/sdb/qemu-new/qemu/vl.c:4420
#11 0x7fb941204812 in __libc_start_main ../csu/libc-start.c:308
#12 0x5585da29420d in _start (/mnt/sdb/qemu-new/qemu/build/x86_64-softmmu/qemu-system-x86_64+0x27f020d)
Indirect leak of 7472 byte(s) in 467 object(s) allocated from:
#0 0x7fb946abd768 in __interceptor_malloc (/lib64/libasan.so.5+0xef768)
#1 0x7fb945eca445 in g_malloc (/lib64/libglib-2.0.so.0+0x52445)
#2 0x7fb945ee2066 in g_slice_alloc (/lib64/libglib-2.0.so.0+0x6a066)
#3 0x7fb945ee3139 in g_slist_prepend (/lib64/libglib-2.0.so.0+0x6b139)
#4 0x5585db591581 in object_class_get_list_tramp /mnt/sdb/qemu-new/qemu/qom/object.c:1084
#5 0x5585db590f66 in object_class_foreach_tramp /mnt/sdb/qemu-new/qemu/qom/object.c:1028
#6 0x7fb945eb35f7 in g_hash_table_foreach (/lib64/libglib-2.0.so.0+0x3b5f7)
#7 0x5585db59110c in object_class_foreach /mnt/sdb/qemu-new/qemu/qom/object.c:1038
#8 0x5585db5916b6 in object_class_get_list /mnt/sdb/qemu-new/qemu/qom/object.c:1092
#9 0x5585db335ca0 in dump_vmstate_json_to_file /mnt/sdb/qemu-new/qemu/migration/savevm.c:638
#10 0x5585daa5bcbf in main /mnt/sdb/qemu-new/qemu/vl.c:4420
#11 0x7fb941204812 in __libc_start_main ../csu/libc-start.c:308
#12 0x5585da29420d in _start (/mnt/sdb/qemu-new/qemu/build/x86_64-softmmu/qemu-system-x86_64+0x27f020d)
Reported-by: Euler Robot <euler.robot@huawei.com>
Signed-off-by: Pan Nengyuan <pannengyuan@huawei.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
qemu_savevm_nr_failover_devices() is originally designed to
get the number of failover devices, but it actually returns
the number of "unplug-pending" failover devices now. Moreover,
what drives migration state to wait-unplug should be the number
of "unplug-pending" failover devices, not all failover devices.
We can also notice that qemu_savevm_state_guest_unplug_pending()
and qemu_savevm_nr_failover_devices() is equivalent almost (from
the code view). So the latter is incorrect semantically and
useless, just delete it.
In the qemu_savevm_state_guest_unplug_pending(), once hit a
unplug-pending failover device, then it can return true right
now to save cpu time.
Signed-off-by: Keqian Zhu <zhukeqian1@huawei.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Tested-by: Jens Freimann <jfreimann@redhat.com>
Reviewed-by: Jens Freimann <jfreimann@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
This function returns true if we are in the middle of a migration.
It is like migration_is_setup_or_active() with CANCELLING and COLO.
Adapt all callers that are needed.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
It was always used as 32bit, so define it as used to be clear.
Instead of using -1 as the auto-gen magic value, we switch to
UINT32_MAX. We also make sure that we don't auto-gen this value to
avoid overflowed instance IDs without being noticed.
Suggested-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Define the new macro VMSTATE_INSTANCE_ID_ANY for callers who wants to
auto-generate the vmstate instance ID. Previously it was hard coded
as -1 instead of this macro. It helps to change this default value in
the follow up patches. No functional change.
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
savevm_state's SaveStateEntry TAILQ is a priority queue. Priority
sorting is maintained by searching from head to tail for a suitable
insertion spot. Insertion is thus an O(n) operation.
If we instead keep track of the head of each priority's subqueue
within that larger queue we can reduce this operation to O(1) time.
savevm_state_handler_remove() becomes slightly more complex to
accomodate these gains: we need to replace the head of a priority's
subqueue when removing it.
With O(1) insertion, booting VMs with many SaveStateEntry objects is
more plausible. For example, a ppc64 VM with maxmem=8T has 40000 such
objects to insert.
Signed-off-by: Scott Cheloha <cheloha@linux.vnet.ibm.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Create a function to abstract common logic needed when removing a
SaveStateEntry element from the savevm_state.handlers queue.
For now we just remove the element. Soon it will involve additional
cleanup.
Signed-off-by: Scott Cheloha <cheloha@linux.vnet.ibm.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Replace DeviceState dependency with VMStateIf on vmstate API.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Acked-by: Halil Pasic <pasic@linux.ibm.com>
.dev_unplug_pending is set up by virtio-net code indepent of failover
support was set for the device or not. This gives a wrong result when
we check for existing primary devices in migration code.
Fix this by actually calling dev_unplug_pending() instead of just
checking if the function pointer was set. When the feature was not
negotiated dev_unplug_pending() will always return false. This prevents
us from going into the wait-unplug state when there's no primary device
present.
Fixes: 9711cd0dfc ("net/virtio: add failover support")
Signed-off-by: Jens Freimann <jfreimann@redhat.com>
Reported-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
This patch adds a new migration state called wait-unplug. It is entered
after the SETUP state if failover devices are present. It will transition
into ACTIVE once all devices were succesfully unplugged from the guest.
So if a guest doesn't respond or takes long to honor the unplug request
the user will see the migration state 'wait-unplug'.
In the migration thread we query failover devices if they're are still
pending the guest unplug. When all are unplugged the migration
continues. If one device won't unplug migration will stay in wait_unplug
state.
Signed-off-by: Jens Freimann <jfreimann@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20191029114905.6856-9-jfreimann@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Currently, we set PostcopyState blindly to RUNNING, even we found the
previous state is not LISTENING. This will lead to a corner case.
First let's look at the code flow:
qemu_loadvm_state_main()
ret = loadvm_process_command()
loadvm_postcopy_handle_run()
return -1;
if (ret < 0) {
if (postcopy_state_get() == POSTCOPY_INCOMING_RUNNING)
...
}
>From above snippet, the corner case is loadvm_postcopy_handle_run()
always sets state to RUNNING. And then it checks the previous state. If
the previous state is not LISTENING, it will return -1. But at this
moment, PostcopyState is already been set to RUNNING.
Then ret is checked in qemu_loadvm_state_main(), when it is -1
PostcopyState is checked. Current logic would pause postcopy and retry
if PostcopyState is RUNNING. This is not what we expect, because
postcopy is not active yet.
This patch makes sure state is set to RUNNING only previous state is
LISTENING by checking the state first.
Signed-off-by: Wei Yang <richardw.yang@linux.intel.com>
Suggested by: Peter Xu <peterx@redhat.com>
Message-Id: <20191010011316.31363-3-richardw.yang@linux.intel.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Function postcopy_ram_incoming_setup and postcopy_ram_incoming_cleanup
is a pair. Rename to make it clear for audience.
Signed-off-by: Wei Yang <richardw.yang@linux.intel.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20191010011316.31363-2-richardw.yang@linux.intel.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
There are two places to call function postcopy_ram_incoming_cleanup()
postcopy_ram_listen_thread on migration success
loadvm_postcopy_handle_listen one setup failure
On success, the vm will never accept another migration. On failure,
PostcopyState is transited from LISTENING to END and would be checked in
qemu_loadvm_state_main(). If PostcopyState is RUNNING, migration would
be paused and retried.
Currently PostcopyState is set to END in function
postcopy_ram_incoming_cleanup(). With above analysis, we can take this
step out and postpone this till the end of listen thread to indicate the
listen thread is done.
This is a preparation patch for later cleanup.
Signed-off-by: Wei Yang <richardw.yang@linux.intel.com>
Message-Id: <20191006000249.29926-3-richardw.yang@linux.intel.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Fixed up in merge to the 1 parameter postcopy_state_set
If mis->have_listen_thread is true, this means current PostcopyState
must be LISTENING or RUNNING. While the check at the beginning of the
function makes sure the state transaction happens when its previous
PostcopyState is ADVISE or DISCARD.
This means we would never touch this check.
Signed-off-by: Wei Yang <richardw.yang@linux.intel.com>
Message-Id: <20191006000249.29926-2-richardw.yang@linux.intel.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
This provides helpful information on which entry failed.
Signed-off-by: Wei Yang <richardw.yang@linux.intel.com>
Message-Id: <20191005220517.24029-5-richardw.yang@linux.intel.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20190912122514.22504-2-marcandre.lureau@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
This capability realizes simple source validation by UUID.
It's useful for live migration between hosts.
Signed-off-by: Yury Kotov <yury-kotov@yandex-team.ru>
Message-Id: <20190903162246.18524-2-yury-kotov@yandex-team.ru>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Commit 78dd48df3 removed the last caller of register_savevm_live for an
instantiable device (rather than a single system wide device);
so trim out the parameter.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20190822115433.12070-1-dgilbert@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
During migration, there are several places to iterate on
savevm.handlers. And on each iteration, we need to check its ops and
related callbacks before invoke it.
Generally, ops is the first element to check, and it is only necessary
to check it once.
This patch clean all the related part in savevm.c to check ops only once
in those iterations.
Signed-off-by: Wei Yang <richardw.yang@linux.intel.com>
Message-Id: <20190819032804.8579-1-richardw.yang@linux.intel.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
-----BEGIN PGP SIGNATURE-----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=eSUz
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/armbru/tags/pull-include-2019-08-13-v2' into staging
Header cleanup patches for 2019-08-13
# gpg: Signature made Fri 16 Aug 2019 12:39:12 BST
# gpg: using RSA key 354BC8B3D7EB2A6B68674E5F3870B400EB918653
# gpg: issuer "armbru@redhat.com"
# gpg: Good signature from "Markus Armbruster <armbru@redhat.com>" [full]
# gpg: aka "Markus Armbruster <armbru@pond.sub.org>" [full]
# Primary key fingerprint: 354B C8B3 D7EB 2A6B 6867 4E5F 3870 B400 EB91 8653
* remotes/armbru/tags/pull-include-2019-08-13-v2: (29 commits)
sysemu: Split sysemu/runstate.h off sysemu/sysemu.h
sysemu: Move the VMChangeStateEntry typedef to qemu/typedefs.h
Include sysemu/sysemu.h a lot less
Clean up inclusion of sysemu/sysemu.h
numa: Move remaining NUMA declarations from sysemu.h to numa.h
Include sysemu/hostmem.h less
numa: Don't include hw/boards.h into sysemu/numa.h
Include hw/boards.h a bit less
Include hw/qdev-properties.h less
Include qemu/main-loop.h less
Include qemu/queue.h slightly less
Include hw/hw.h exactly where needed
Include qom/object.h slightly less
Include exec/memory.h slightly less
Include migration/vmstate.h less
migration: Move the VMStateDescription typedef to typedefs.h
Clean up inclusion of exec/cpu-common.h
Include hw/irq.h a lot less
typedefs: Separate incomplete types and function types
ide: Include hw/ide/internal a bit less outside hw/ide/
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
sysemu/sysemu.h is a rather unfocused dumping ground for stuff related
to the system-emulator. Evidence:
* It's included widely: in my "build everything" tree, changing
sysemu/sysemu.h still triggers a recompile of some 1100 out of 6600
objects (not counting tests and objects that don't depend on
qemu/osdep.h, down from 5400 due to the previous two commits).
* It pulls in more than a dozen additional headers.
Split stuff related to run state management into its own header
sysemu/runstate.h.
Touching sysemu/sysemu.h now recompiles some 850 objects. qemu/uuid.h
also drops from 1100 to 850, and qapi/qapi-types-run-state.h from 4400
to 4200. Touching new sysemu/runstate.h recompiles some 500 objects.
Since I'm touching MAINTAINERS to add sysemu/runstate.h anyway, also
add qemu/main-loop.h.
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190812052359.30071-30-armbru@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
[Unbreak OS-X build]
In my "build everything" tree, changing sysemu/sysemu.h triggers a
recompile of some 5400 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).
hw/qdev-core.h includes sysemu/sysemu.h since recent commit e965ffa70a
"qdev: add qdev_add_vm_change_state_handler()". This is a bad idea:
hw/qdev-core.h is widely included.
Move the declaration of qdev_add_vm_change_state_handler() to
sysemu/sysemu.h, and drop the problematic include from hw/qdev-core.h.
Touching sysemu/sysemu.h now recompiles some 1800 objects.
qemu/uuid.h also drops from 5400 to 1800. A few more headers show
smaller improvement: qemu/notify.h drops from 5600 to 5200,
qemu/timer.h from 5600 to 4500, and qapi/qapi-types-run-state.h from
5500 to 5000.
Cc: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20190812052359.30071-28-armbru@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
In my "build everything" tree, changing qemu/main-loop.h triggers a
recompile of some 5600 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h). It includes block/aio.h,
which in turn includes qemu/event_notifier.h, qemu/notify.h,
qemu/processor.h, qemu/qsp.h, qemu/queue.h, qemu/thread-posix.h,
qemu/thread.h, qemu/timer.h, and a few more.
Include qemu/main-loop.h only where it's needed. Touching it now
recompiles only some 1700 objects. For block/aio.h and
qemu/event_notifier.h, these numbers drop from 5600 to 2800. For the
others, they shrink only slightly.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190812052359.30071-21-armbru@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
In my "build everything" tree, changing migration/vmstate.h triggers a
recompile of some 2700 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).
hw/hw.h supposedly includes it for convenience. Several other headers
include it just to get VMStateDescription. The previous commit made
that unnecessary.
Include migration/vmstate.h only where it's still needed. Touching it
now recompiles only some 1600 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190812052359.30071-16-armbru@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
For migration incoming side, it either quit in precopy or postcopy. It
is safe to use the mis->bh for both instead of allocating a dedicated
QEMUBH for postcopy.
Signed-off-by: Wei Yang <richardw.yang@linux.intel.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20190805053146.32326-1-richardw.yang@linux.intel.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
This patch fix a multifd migration bug in migration speed calculation, this
problem can be reproduced as follows:
1. start a vm and give a heavy memory write stress to prevent the vm be
successfully migrated to destination
2. begin a migration with multifd
3. migrate for a long time [actually, this can be measured by transferred bytes]
4. migrate cancel
5. begin a new migration with multifd, the migration will directly run into
migration_completion phase
Reason as follows:
Migration update bandwidth and s->threshold_size in function
migration_update_counters after BUFFER_DELAY time:
current_bytes = migration_total_bytes(s);
transferred = current_bytes - s->iteration_initial_bytes;
time_spent = current_time - s->iteration_start_time;
bandwidth = (double)transferred / time_spent;
s->threshold_size = bandwidth * s->parameters.downtime_limit;
In multifd migration, migration_total_bytes function return
qemu_ftell(s->to_dst_file) + ram_counters.multifd_bytes.
s->iteration_initial_bytes will be initialized to 0 at every new migration,
but ram_counters is a global variable, and history migration data will be
accumulated. So if the ram_counters.multifd_bytes is big enough, it may lead
pending_size >= s->threshold_size become false in migration_iteration_run
after the first migration_update_counters.
Signed-off-by: Ivan Ren <ivanren@tencent.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Wei Yang <richardw.yang@linux.intel.com>
Suggested-by: Wei Yang <richardw.yang@linux.intel.com>
Message-Id: <1564741121-1840-1-git-send-email-ivanren@tencent.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
LOADVM_QUIT allows a command to quit all layers of nested loadvm loops,
while current return value check is not that proper even it works now.
Current return value check "ret & LOADVM_QUIT" would return true if
bit[0] is 1. This would be true when ret is -1 which is used to indicate
an error of handling a command.
Since there is only one place return LOADVM_QUIT and no other
combination of return value, use "ret == LOADVM_QUIT" would be more
proper.
Signed-off-by: Wei Yang <richardw.yang@linux.intel.com>
Message-Id: <20190718064257.29218-1-richardw.yang@linux.intel.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
PostcopyState is already set to ADVISE at the beginning of
loadvm_postcopy_handle_advise().
Remove the redundant set.
Signed-off-by: Wei Yang <richardw.yang@linux.intel.com>
Message-Id: <20190711080816.6405-1-richardw.yang@linux.intel.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
in_postcopy and iterable_only are not SaveStateEntry specific, it would
be more proper to check them out of iteration.
Signed-off-by: Wei Yang <richardw.yang@linux.intel.com>
Message-Id: <20190709140924.13291-4-richardw.yang@linux.intel.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
This is a preparation patch for further cleanup.
No functional change, just wrap two major part of
qemu_savevm_state_complete_precopy() into function.
Signed-off-by: Wei Yang <richardw.yang@linux.intel.com>
Message-Id: <20190709140924.13291-3-richardw.yang@linux.intel.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
It would be proper to flush file even for iterable_only case.
Signed-off-by: Wei Yang <richardw.yang@linux.intel.com>
Message-Id: <20190709140924.13291-2-richardw.yang@linux.intel.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Currently, there is no information about error if outgoing migration was failed
because of file channel errors.
Example (QMP session):
-> { "execute": "migrate", "arguments": { "uri": "exec:head -c 1" }}
<- { "return": {} }
...
-> { "execute": "query-migrate" }
<- { "return": { "status": "failed" }} // There is not error's description
And even in the QEMU's output there is nothing.
This patch
1) Adds errp for the most of QEMUFileOps
2) Adds qemu_file_get_error_obj/qemu_file_set_error_obj
3) And finally using of qemu_file_get_error_obj in migration.c
And now, the status for the mentioned fail will be:
-> { "execute": "query-migrate" }
<- { "return": { "status": "failed",
"error-desc": "Unable to write to command: Broken pipe" }}
Signed-off-by: Yury Kotov <yury-kotov@yandex-team.ru>
Message-Id: <20190422103420.15686-1-yury-kotov@yandex-team.ru>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
cpu_synchronize_all_post_init() is called twice in
loadvm_postcopy_handle_run_bh(), so remove one redundant call.
Signed-off-by: Wei Yang <richardw.yang@linux.intel.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20190715080751.24304-1-richardw.yang@linux.intel.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
On source side, we have qemu_savevm_state_header() to send related data,
while on the receiving side those steps are scattered in
qemu_loadvm_state().
This patch wrap those related steps into qemu_loadvm_state_header() to
make it friendly to read.
Signed-off-by: Wei Yang <richardw.yang@linux.intel.com>
Message-Id: <20190424004700.12766-5-richardw.yang@linux.intel.com>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
In migration_thread() and qemu_savevm_state(), we savevm_state in
following sequence:
qemu_savevm_state_header(f);
qemu_savevm_state_setup(f);
Then it would be more proper to loadvm_state in the save sequence.
Signed-off-by: Wei Yang <richardw.yang@linux.intel.com>
Message-Id: <20190424004700.12766-4-richardw.yang@linux.intel.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
