The AST2600 control register sneakily changed the meaning of bit 4
without anyone noticing. It no longer controls the 1MHz vs APB clock
select, and instead always runs at 1MHz.
The AST2500 was always 1MHz too, but it retained bit 4, making it read
only. We can model both using the same fixed 1MHz calculation.
Fixes: 6b2b2a703c ("hw: wdt_aspeed: Add AST2600 support")
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20191119141211.25716-10-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The I2C controller of the Aspeed AST2500 and AST2600 SoCs supports DMA
transfers to and from DRAM.
A pair of registers defines the buffer address and the length of the
DMA transfer. The address should be aligned on 4 bytes and the maximum
length should not exceed 4K. The receive or transmit DMA transfer can
then be initiated with specific bits in the Command/Status register of
the controller.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Tested-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20191119141211.25716-5-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Currently, we link the DRAM memory region to the FMC model (for DMAs)
through a property alias at the SoC level. The I2C model will need a
similar region for DMA support, add a DRAM region property at the SoC
level for both model to use.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Tested-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20191119141211.25716-4-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The SRAM must be enabled before using the Buffer Pool mode or the DMA
mode. This is not required on other SoCs.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Tested-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20191119141211.25716-3-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Aspeed I2C controller can operate in different transfer modes :
- Byte Buffer mode, using a dedicated register to transfer a
byte. This is what the model supports today.
- Pool Buffer mode, using an internal SRAM to transfer multiple
bytes in the same command sequence.
Each SoC has different SRAM characteristics. On the AST2400, 2048
bytes of SRAM are available at offset 0x800 of the controller AHB
window. The pool buffer can be configured from 1 to 256 bytes per bus.
On the AST2500, the SRAM is at offset 0x200 and the pool buffer is of
16 bytes per bus.
On the AST2600, the SRAM is at offset 0xC00 and the pool buffer is of
32 bytes per bus. It can be splitted in two for TX and RX but the
current model does not add support for it as it it unused by known
drivers.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Tested-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20191119141211.25716-2-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add 5.0 machine types for arm/i440fx/q35/s390x/spapr.
For i440fx and q35, unversioned cpu models are still translated
to -v1; I'll leave changing this (if desired) to the respective
maintainers.
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Message-Id: <20191112104811.30323-1-cohuck@redhat.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Virtio spec 1.1 (and earlier), 5.2.5.2 Driver Requirements: Device
Initialization:
"Devices SHOULD always offer VIRTIO_BLK_F_FLUSH, and MUST offer it if
they offer VIRTIO_BLK_F_CONFIG_WCE"
Currently F_CONFIG_WCE and F_WCE are not connected to each other.
Qemu will advertise F_CONFIG_WCE if config-wce argument is
set for virtio-blk device. And F_WCE is advertised only if
underlying block backend actually has it's caching enabled.
Fix this by advertising F_WCE if F_CONFIG_WCE is also advertised.
To preserve backwards compatibility with newer machine types make this
behaviour governed by "x-enable-wce-if-config-wce" virtio-blk-device
property and introduce hw_compat_4_2 with new property being off by
default for all machine types <= 4.2 (but don't introduce 4.3
machine type itself yet).
Signed-off-by: Evgeny Yakovlev <wrfsh@yandex-team.ru>
Message-Id: <1572978137-189218-1-git-send-email-wrfsh@yandex-team.ru>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
The property doesn't make much sense for a vhost-user device.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20191116112016.14872-1-marcandre.lureau@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Here's the first 4.2 hard freeze pull request from me. This has:
* A fix for some testcases that cause errors on older host kernels
(e.g. RHEL7), with our new default configuration of VSMT mode
* Changes to make VFIO devices interact properly with change of irq
chip caused by PAPR feature negotiation. This is more involved
than I would like, but it's a problem in real use cases and I
can't see an easier way to handle it.
* Fix an error with ms6522 counters for the g3beige machine
* Fix a coverity warning
-----BEGIN PGP SIGNATURE-----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=GHGC
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dgibson/tags/ppc-for-4.2-20191126' into staging
ppc patch queue for 2019-11-26
Here's the first 4.2 hard freeze pull request from me. This has:
* A fix for some testcases that cause errors on older host kernels
(e.g. RHEL7), with our new default configuration of VSMT mode
* Changes to make VFIO devices interact properly with change of irq
chip caused by PAPR feature negotiation. This is more involved
than I would like, but it's a problem in real use cases and I
can't see an easier way to handle it.
* Fix an error with ms6522 counters for the g3beige machine
* Fix a coverity warning
# gpg: Signature made Tue 26 Nov 2019 05:52:16 GMT
# gpg: using RSA key 75F46586AE61A66CC44E87DC6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>" [full]
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>" [full]
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>" [full]
# gpg: aka "David Gibson (kernel.org) <dwg@kernel.org>" [unknown]
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dgibson/tags/ppc-for-4.2-20191126:
ppc/spapr_events: fix potential NULL pointer dereference in rtas_event_log_dequeue
mos6522: update counters when timer interrupts are off
spapr: Work around spurious warnings from vfio INTx initialization
spapr: Handle irq backend changes with VFIO PCI devices
vfio/pci: Respond to KVM irqchip change notifier
vfio/pci: Split vfio_intx_update()
kvm: Introduce KVM irqchip change notifier
pseries: fix migration-test and pxe-test
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add the CRP as unimplemented thus avoiding bus errors when
guests access these registers.
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Message-id: 20191115154734.26449-2-edgar.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Awareness of an in kernel irqchip is usually local to the machine and its
top-level interrupt controller. However, in a few cases other things need
to know about it. In particular vfio devices need this in order to
accelerate interrupt delivery.
If interrupt routing is changed, such devices may need to readjust their
connection to the KVM irqchip. pci_bus_fire_intx_routing_notifier() exists
to do just this.
However, for the pseries machine type we have a situation where the routing
remains constant but the top-level irq chip itself is changed. This occurs
because of PAPR feature negotiation which allows the guest to decide
between the older XICS and newer XIVE irq chip models (both of which are
paravirtualized).
To allow devices like vfio to adjust to this change, introduce a new
notifier for the purpose kvm_irqchip_change_notify().
Cc: Alex Williamson <alex.williamson@redhat.com>
Cc: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Tested-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
This patch adds an optional function pointer, "sym_cb", to
riscv_load_kernel() which provides the possibility to access the symbol
table during kernel loading.
The pointer is ignored, if supplied with Image or uImage file.
The Spike board requires the access to locate the HTIF symbols.
Fixes: 0ac24d56c5 ("hw/riscv: Split out the boot functions")
Buglink: https://bugs.launchpad.net/qemu/+bug/1835827
Signed-off-by: Siwei Zhuang <siwei.zhuang@data61.csiro.au>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
Attempting to migrate a VM using the microvm machine class results in the source
QEMU aborting with the following message/backtrace:
target/i386/machine.c:955:tsc_khz_needed: Object 0x555556608fa0 is not an
instance of type generic-pc-machine
abort()
object_class_dynamic_cast_assert()
vmstate_save_state_v()
vmstate_save_state()
vmstate_save()
qemu_savevm_state_complete_precopy()
migration_thread()
migration_thread()
migration_thread()
qemu_thread_start()
start_thread()
clone()
The access to the machine class returned by MACHINE_GET_CLASS() in
tsc_khz_needed() is crashing as it is trying to dereference a different
type of machine class object (TYPE_PC_MACHINE) to that of this microVM.
This can be resolved by extending the changes in the following commit
f0bb276bf8 ("hw/i386: split PCMachineState deriving X86MachineState from it")
and moving the save_tsc_khz field in PCMachineClass to X86MachineClass.
Fixes: f0bb276bf8 ("hw/i386: split PCMachineState deriving X86MachineState from it")
Signed-off-by: Liam Merwick <liam.merwick@oracle.com>
Reviewed-by: Darren Kenny <darren.kenny@oracle.com>
Message-Id: <1574075605-25215-1-git-send-email-liam.merwick@oracle.com>
Reviewed-by: Sergio Lopez <slp@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Qemu as server currently won't accept export names larger than 256
bytes, nor create dirty bitmap names longer than 1023 bytes, so most
uses of qemu as client or server have no reason to get anywhere near
the NBD spec maximum of a 4k limit per string.
However, we weren't actually enforcing things, ignoring when the
remote side violates the protocol on input, and also having several
code paths where we send oversize strings on output (for example,
qemu-nbd --description could easily send more than 4k). Tighten
things up as follows:
client:
- Perform bounds check on export name and dirty bitmap request prior
to handing it to server
- Validate that copied server replies are not too long (ignoring
NBD_INFO_* replies that are not copied is not too bad)
server:
- Perform bounds check on export name and description prior to
advertising it to client
- Reject client name or metadata query that is too long
- Adjust things to allow full 4k name limit rather than previous
256 byte limit
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <20191114024635.11363-4-eblake@redhat.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
We document that for qcow2 persistent bitmaps, the name cannot exceed
1023 bytes. It is inconsistent if transient bitmaps do not have to
abide by the same limit, and it is unlikely that any existing client
even cares about using bitmap names this long. It's time to codify
that ALL bitmaps managed by qemu (whether persistent in qcow2 or not)
have a documented maximum length.
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <20191114024635.11363-3-eblake@redhat.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
As long as we limit NBD names to 256 bytes (the bare minimum permitted
by the standard), stack-allocation works for parsing a name received
from the client. But as mentioned in a comment, we eventually want to
permit up to the 4k maximum of the NBD standard, which is too large
for stack allocation; so switch everything in the server to use heap
allocation. For now, there is no change in actually supported name
length.
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <20191114024635.11363-2-eblake@redhat.com>
[eblake: fix uninit variable compile failure]
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
SpaprInterruptControllerClass and PnvChipClass have an intc_create() method
that calls the appropriate routine, ie. icp_create() or xive_tctx_create(),
to establish the link between the VCPU and the presenter component of the
interrupt controller during realize.
There aren't any symmetrical call to be called when the VCPU gets unrealized
though. It is assumed that object_unparent() is the only thing to do.
This is questionable because the parenting logic around the CPU and
presenter objects is really an implementation detail of the interrupt
controller. It shouldn't be open-coded in the machine code.
Fix this by adding an intc_destroy() method that undoes what was done in
intc_create(). Also NULLify the presenter pointers to avoid having
stale pointers around. This will allow to reliably check if a vCPU has
a valid presenter.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <157192724208.3146912.7254684777515287626.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
This is a very simple versioning API which allows the plugin
infrastructure to check the API a plugin was built against. We also
expose a min/cur API version to the plugin via the info block in case
it wants to avoid using old deprecated APIs in the future.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Robert Foley <robert.foley@linaro.org>
The boot.c code usually puts the CPU into NS mode directly when it is
booting a kernel. Since fc1120a7f5 this has included a
requirement to set NSACR to give NS state access to the FPU; we fixed
that for the usual code path in ece628fcf6. However, it is also
possible for a board model to request an alternative mode of booting,
where its 'board_setup' code hook runs in Secure state and is
responsible for doing the S->NS transition after it has done whatever
work it must do in Secure state. In this situation the board_setup
code now also needs to update NSACR.
This affects all boards which set info->secure_board_setup, which is
currently the 'raspi' and 'highbank' families. They both use the
common arm_write_secure_board_setup_dummy_smc().
Set the NSACR CP11 and CP10 bits in the code written by that
function, to allow FPU access in Non-Secure state when using dummy
SMC setup routine. Otherwise an AArch32 kernel booted on the
highbank or raspi boards will UNDEF as soon as it tries to use the
FPU.
Update the comment describing secure_board_setup to note the new
requirements on users of it.
This fixes a kernel panic when booting raspbian on raspi2.
Successfully tested with:
2017-01-11-raspbian-jessie-lite.img
2018-11-13-raspbian-stretch-lite.img
2019-07-10-raspbian-buster-lite.img
Fixes: fc1120a7f5
Signed-off-by: Clement Deschamps <clement.deschamps@greensocs.com>
Tested-by: Laurent Bonnans <laurent.bonnans@here.com>
Message-id: 20191104151137.81931-1-clement.deschamps@greensocs.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: updated comment to boot.h to note new requirement on
users of secure_board_setup; edited/rewrote commit message]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
All targets have now migrated away from the old unassigned_access
hook to the new do_transaction_failed hook. This means we can remove
the core-code infrastructure for that hook and the code that calls it.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20191108173732.11816-1-peter.maydell@linaro.org
Now all the users of ptimers have converted to the transaction-based
API, we can remove ptimer_init_with_bh() and all the code paths
that are used only by bottom-half based ptimers, and tidy up the
documentation comments to consider the transaction-based API the
only possibility.
The code changes result from:
* s->bh no longer exists
* s->callback is now always non-NULL
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20191025142411.17085-1-peter.maydell@linaro.org
PIIX southbridge is also used by the Malta MIPS machine.
Split the PIIX3 southbridge from i440FX northbridge.
-----BEGIN PGP SIGNATURE-----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=cQ/y
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/philmd-gitlab/tags/mips-next-20191105' into staging
The i440FX northbridge is only used by the PC machine, while the
PIIX southbridge is also used by the Malta MIPS machine.
Split the PIIX3 southbridge from i440FX northbridge.
# gpg: Signature made Tue 05 Nov 2019 22:48:12 GMT
# gpg: using RSA key 89C1E78F601EE86C867495CBA2A3FD6EDEADC0DE
# gpg: Good signature from "Philippe Mathieu-Daudé (Phil) <philmd@redhat.com>" [marginal]
# gpg: WARNING: This key is not certified with sufficiently trusted signatures!
# gpg: It is not certain that the signature belongs to the owner.
# Primary key fingerprint: 89C1 E78F 601E E86C 8674 95CB A2A3 FD6E DEAD C0DE
* remotes/philmd-gitlab/tags/mips-next-20191105: (21 commits)
hw/pci-host/i440fx: Remove the last PIIX3 traces
hw/pci-host: Rename incorrectly named 'piix' as 'i440fx'
hw/pci-host/piix: Extract PIIX3 functions to hw/isa/piix3.c
hw/pci-host/piix: Fix code style issues
hw/pci-host/piix: Move i440FX declarations to hw/pci-host/i440fx.h
hw/pci-host/piix: Define and use the PIIX IRQ Route Control Registers
hw/pci-host/piix: Move RCR_IOPORT register definition
hw/pci-host/piix: Extract piix3_create()
hw/i386: Remove obsolete LoadStateHandler::load_state_old handlers
hw/isa/piix4: Move piix4_create() to hw/isa/piix4.c
hw/mips/mips_malta: Extract the PIIX4 creation code as piix4_create()
hw/mips/mips_malta: Create IDE hard drive array dynamically
piix4: Add a MC146818 RTC Controller as specified in datasheet
piix4: Add an i8254 PIT Controller as specified in datasheet
piix4: Add an i8257 DMA Controller as specified in datasheet
piix4: Rename PIIX4 object to piix4-isa
Revert "irq: introduce qemu_irq_proxy()"
piix4: Add an i8259 Interrupt Controller as specified in datasheet
piix4: Add the Reset Control Register
MAINTAINERS: Keep PIIX4 South Bridge separate from PC Chipsets
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
'the' has a tendency to double up; squash them back down.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20191104185202.102504-1-dgilbert@redhat.com>
[lv: removed disas/libvixl/vixl/invalset.h change]
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Host notifiers are used in several cases:
1. Traditional ioeventfd where virtqueue notifications are handled in
the main loop thread.
2. IOThreads (aio_handle_output) where virtqueue notifications are
handled in an IOThread AioContext.
3. vhost where virtqueue notifications are handled by kernel vhost or
a vhost-user device backend.
Most virtqueue notifications from the guest use the ioeventfd mechanism,
but there are corner cases where QEMU code calls virtio_queue_notify().
This currently honors the host notifier for the IOThreads
aio_handle_output case, but not for the vhost case. The result is that
vhost does not receive virtqueue notifications from QEMU when
virtio_queue_notify() is called.
This patch extends virtio_queue_notify() to set the host notifier
whenever it is enabled instead of calling the vq->(aio_)handle_output()
function directly. We track the host notifier state for each virtqueue
separately since some devices may use it only for certain virtqueues.
This fixes the vhost case although it does add a trip through the
eventfd for the traditional ioeventfd case. I don't think it's worth
adding a fast path for the traditional ioeventfd case because calling
virtio_queue_notify() is rare when ioeventfd is enabled.
Reported-by: Felipe Franciosi <felipe@nutanix.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20191105140946.165584-1-stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The PIIX3 is not tied to the i440FX and can even be used without it.
Move its creation to the machine code (pc_piix.c).
We have now removed the last trace of southbridge code in the i440FX
northbridge.
Reviewed-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Move all the PIIX3 functions to a new file: hw/isa/piix3.c.
Reviewed-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
The hw/pci-host/piix.c contains a mix of PIIX3 and i440FX chipsets
functions. To be able to split it, we need to export some
declarations first.
Reviewed-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
The IRQ Route Control registers definitions belong to the PIIX
chipset. We were only defining the 'A' register. Define the other
B, C and D registers, and use them.
Acked-by: Paul Durrant <paul@xen.org>
Reviewed-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
The RCR_IOPORT register belongs to the PIIX chipset.
Move the definition to "piix.h", and prepend the PIIX prefix.
Reviewed-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Now that we properly refactored the piix4_create() function, let's
move it to hw/isa/piix4.c where it belongs, so it can be reused
on other places.
Reviewed-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Remove mc146818rtc instanciated in malta board, to not have it twice.
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Message-Id: <20171216090228.28505-13-hpoussin@reactos.org>
[PMD: rebased, set RTC base_year to 2000]
Reviewed-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Other piix4 parts are already named piix4-ide and piix4-usb-uhci.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Message-Id: <20171216090228.28505-15-hpoussin@reactos.org>
Reviewed-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Reviewed-by: Li Qiang <liq3ea@gmail.com>
Reviewed-by: Esteban Bosse <estebanbosse@gmail.com>
[PMD: rebased]
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
This function isn't used anymore.
This reverts commit 22ec3283ef.
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Li Qiang <liq3ea@gmail.com>
Reviewed-by: Esteban Bosse <estebanbosse@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Add ISA irqs as piix4 gpio in, and CPU interrupt request as piix4 gpio out.
Remove i8259 instanciated in malta board, to not have it twice.
We can also remove the now unused piix4_init() function.
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Message-Id: <20171216090228.28505-8-hpoussin@reactos.org>
Reviewed-by: Aleksandar Markovic <amarkovic@wavecomp.com>
[PMD: rebased, updated includes, use ISA_NUM_IRQS in for loop]
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Make both bdrv_mark_request_serialising() and
bdrv_wait_serialising_requests() public so they can be used from block
drivers.
Cc: qemu-stable@nongnu.org
Signed-off-by: Max Reitz <mreitz@redhat.com>
Message-id: 20191101152510.11719-2-mreitz@redhat.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
Fix the offset of the NSSRS field the CAP register.
From NVME 1.4, section 3 ("Controller Registers"), subsection 3.1.1
("Offset 0h: CAP – Controller Capabilities") CAP_NSSRS_SHIFT is bit 36,
not 33.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reported-by: Javier Gonzalez <javier.gonz@samsung.com>
Message-id: 20191023073315.446534-1-its@irrelevant.dk
Reviewed-by: John Snow <jsnow@redhat.com>
[mreitz: Added John's note on the location in the specification where
this information can be found]
Signed-off-by: Max Reitz <mreitz@redhat.com>
Introduce cpu properties to give fine control over SVE vector lengths.
We introduce a property for each valid length up to the current
maximum supported, which is 2048-bits. The properties are named, e.g.
sve128, sve256, sve384, sve512, ..., where the number is the number of
bits. See the updates to docs/arm-cpu-features.rst for a description
of the semantics and for example uses.
Note, as sve-max-vq is still present and we'd like to be able to
support qmp_query_cpu_model_expansion with guests launched with e.g.
-cpu max,sve-max-vq=8 on their command lines, then we do allow
sve-max-vq and sve<N> properties to be provided at the same time, but
this is not recommended, and is why sve-max-vq is not mentioned in the
document. If sve-max-vq is provided then it enables all lengths smaller
than and including the max and disables all lengths larger. It also has
the side-effect that no larger lengths may be enabled and that the max
itself cannot be disabled. Smaller non-power-of-two lengths may,
however, be disabled, e.g. -cpu max,sve-max-vq=4,sve384=off provides a
guest the vector lengths 128, 256, and 512 bits.
This patch has been co-authored with Richard Henderson, who reworked
the target/arm/cpu64.c changes in order to push all the validation and
auto-enabling/disabling steps into the finalizer, resulting in a nice
LOC reduction.
Signed-off-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Masayoshi Mizuma <m.mizuma@jp.fujitsu.com>
Reviewed-by: Beata Michalska <beata.michalska@linaro.org>
Message-id: 20191031142734.8590-5-drjones@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Using fw_cfg, supply logical CHS values directly from QEMU to the BIOS.
Non-standard logical geometries break under QEMU.
A virtual disk which contains an operating system which depends on
logical geometries (consistent values being reported from BIOS INT13
AH=08) will most likely break under QEMU/SeaBIOS if it has non-standard
logical geometries - for example 56 SPT (sectors per track).
No matter what QEMU will report - SeaBIOS, for large enough disks - will
use LBA translation, which will report 63 SPT instead.
In addition we cannot force SeaBIOS to rely on physical geometries at
all. A virtio-blk-pci virtual disk with 255 phyiscal heads cannot
report more than 16 physical heads when moved to an IDE controller,
since the ATA spec allows a maximum of 16 heads - this is an artifact of
virtualization.
By supplying the logical geometries directly we are able to support such
"exotic" disks.
We serialize this information in a similar way to the "bootorder"
interface.
The new fw_cfg entry is "bios-geometry".
Reviewed-by: Karl Heubaum <karl.heubaum@oracle.com>
Reviewed-by: Arbel Moshe <arbel.moshe@oracle.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Sam Eiderman <shmuel.eiderman@oracle.com>
Signed-off-by: Sam Eiderman <sameid@google.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
We will need to add LCHS removal logic to scsi-hd's unrealize() in the
next commit.
Reviewed-by: Karl Heubaum <karl.heubaum@oracle.com>
Reviewed-by: Arbel Moshe <arbel.moshe@oracle.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Sam Eiderman <shmuel.eiderman@oracle.com>
Signed-off-by: Sam Eiderman <sameid@google.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Add an interface to provide direct logical CHS values for boot devices.
We will use this interface in the next commits.
Reviewed-by: Karl Heubaum <karl.heubaum@oracle.com>
Reviewed-by: Arbel Moshe <arbel.moshe@oracle.com>
Signed-off-by: Sam Eiderman <shmuel.eiderman@oracle.com>
Signed-off-by: Sam Eiderman <sameid@google.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Add logical geometry variables to BlockConf.
A user can now supply "lcyls", "lheads" & "lsecs" for any HD device
that supports CHS ("cyls", "heads", "secs").
These devices include:
* ide-hd
* scsi-hd
* virtio-blk-pci
In future commits we will use the provided LCHS and pass it to the BIOS
through fw_cfg to be supplied using INT13 routines.
Reviewed-by: Karl Heubaum <karl.heubaum@oracle.com>
Reviewed-by: Arbel Moshe <arbel.moshe@oracle.com>
Signed-off-by: Sam Eiderman <shmuel.eiderman@oracle.com>
Signed-off-by: Sam Eiderman <sameid@google.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Fixing tabbing in block related macros.
Signed-off-by: Sam Eiderman <shmuel.eiderman@oracle.com>
Signed-off-by: Sam Eiderman <sameid@google.com>
Reviewed-by: Karl Heubaum <karl.heubaum@oracle.com>
Reviewed-by: Arbel Moshe <arbel.moshe@oracle.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
- use --enable-plugins @ configure
- low impact introspection (-plugin empty.so to measure overhead)
- plugins cannot alter guest state
- example plugins included in source tree (tests/plugins)
- -d plugin to enable plugin output in logs
- check-tcg runs extra tests when plugins enabled
- documentation in docs/devel/plugins.rst
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEZoWumedRZ7yvyN81+9DbCVqeKkQFAl23BZMACgkQ+9DbCVqe
KkRPegf/QHygZ4ER2jOaWEookxiOEcik+dzQKVGNqLNXeMLvo5fGjGVpFoFxSgfv
ZvCAL4xbW44zsYlVfh59tfn4Tu9qK7s7/qM3WXpHsmuvEuhoWef0Lt2jSe+D46Rs
KeG/aX+rHLUR8rr9eCgE+1/MQmxPUj3VUonkUpNkk2ebBbSNoLSOudB4DD9Vcyl7
Pya1kPvA6W9bwI20ZSWihE7flg13o62Pp+LgAFLrsfxXOxOMkPrU8Pp+B0Dvr+hL
5Oh0clZLhiRi75x+KVGZ90TVsoftdjYoOWGMOudS/+NNmqKT1NTLm0K1WJYyRMQ1
V0ne4/OcGNq7x8gcOx/xs09ADu5/VA==
=UXR/
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/stsquad/tags/pull-tcg-plugins-281019-4' into staging
TCG Plugins initial implementation
- use --enable-plugins @ configure
- low impact introspection (-plugin empty.so to measure overhead)
- plugins cannot alter guest state
- example plugins included in source tree (tests/plugins)
- -d plugin to enable plugin output in logs
- check-tcg runs extra tests when plugins enabled
- documentation in docs/devel/plugins.rst
# gpg: Signature made Mon 28 Oct 2019 15:13:23 GMT
# gpg: using RSA key 6685AE99E75167BCAFC8DF35FBD0DB095A9E2A44
# gpg: Good signature from "Alex Bennée (Master Work Key) <alex.bennee@linaro.org>" [full]
# Primary key fingerprint: 6685 AE99 E751 67BC AFC8 DF35 FBD0 DB09 5A9E 2A44
* remotes/stsquad/tags/pull-tcg-plugins-281019-4: (57 commits)
travis.yml: enable linux-gcc-debug-tcg cache
MAINTAINERS: add me for the TCG plugins code
scripts/checkpatch.pl: don't complain about (foo, /* empty */)
.travis.yml: add --enable-plugins tests
include/exec: wrap cpu_ldst.h in CONFIG_TCG
accel/stubs: reduce headers from tcg-stub
tests/plugin: add hotpages to analyse memory access patterns
tests/plugin: add instruction execution breakdown
tests/plugin: add a hotblocks plugin
tests/tcg: enable plugin testing
tests/tcg: drop test-i386-fprem from TESTS when not SLOW
tests/tcg: move "virtual" tests to EXTRA_TESTS
tests/tcg: set QEMU_OPTS for all cris runs
tests/tcg/Makefile.target: fix path to config-host.mak
tests/plugin: add sample plugins
linux-user: support -plugin option
vl: support -plugin option
plugin: add qemu_plugin_outs helper
plugin: add qemu_plugin_insn_disas helper
plugin: expand the plugin_init function to include an info block
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch adds support to handle failover device pairs of a virtio-net
device and a (vfio-)pci device, where the virtio-net acts as the standby
device and the (vfio-)pci device as the primary.
The general idea is that we have a pair of devices, a (vfio-)pci and a
emulated (virtio-net) device. Before migration the vfio device is
unplugged and data flows to the emulated device, on the target side
another (vfio-)pci device is plugged in to take over the data-path. In the
guest the net_failover module will pair net devices with the same MAC
address.
To achieve this we need:
1. Provide a callback function for the should_be_hidden DeviceListener.
It is called when the primary device is plugged in. Evaluate the QOpt
passed in to check if it is the matching primary device. It returns
if the device should be hidden or not.
When it should be hidden it stores the device options in the VirtioNet
struct and the device is added once the VIRTIO_NET_F_STANDBY feature is
negotiated during virtio feature negotiation.
If the virtio-net devices are not realized at the time the (vfio-)pci
devices are realized, we need to connect the devices later. This way
we make sure primary and standby devices can be specified in any
order.
2. Register a callback for migration status notifier. When called it
will unplug its primary device before the migration happens.
3. Register a callback for the migration code that checks if a device
needs to be unplugged from the guest.
Signed-off-by: Jens Freimann <jfreimann@redhat.com>
Message-Id: <20191029114905.6856-11-jfreimann@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This patch adds a new migration state called wait-unplug. It is entered
after the SETUP state if failover devices are present. It will transition
into ACTIVE once all devices were succesfully unplugged from the guest.
So if a guest doesn't respond or takes long to honor the unplug request
the user will see the migration state 'wait-unplug'.
In the migration thread we query failover devices if they're are still
pending the guest unplug. When all are unplugged the migration
continues. If one device won't unplug migration will stay in wait_unplug
state.
Signed-off-by: Jens Freimann <jfreimann@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20191029114905.6856-9-jfreimann@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
In "b06424de62 migration: Disable hotplug/unplug during migration" we
added a check to disable unplug for all devices until we have figured
out what works. For failover primary devices qdev_unplug() is called
from the migration handler, i.e. during migration.
This patch adds a flag to DeviceState which is set to false for all
devices and makes an exception for PCI devices that are also
primary devices in a failover pair.
Signed-off-by: Jens Freimann <jfreimann@redhat.com>
Message-Id: <20191029114905.6856-8-jfreimann@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Only the guest unplug request was triggered. This is needed for
the failover feature. In case of a failed migration we need to
plug the device back to the guest.
Signed-off-by: Jens Freimann <jfreimann@redhat.com>
Message-Id: <20191029114905.6856-4-jfreimann@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This patch adds a failover_pair_id property to PCIDev which is
used to link the primary device in a failover pair (the PCI dev) to
a standby (a virtio-net-pci) device.
It only supports ethernet devices. Also currently it only supports
PCIe devices. The requirement for PCIe is because it doesn't support
other hotplug controllers at the moment. The failover functionality can
be added to other hotplug controllers like ACPI, SHCP,... later on.
Signed-off-by: Jens Freimann <jfreimann@redhat.com>
Message-Id: <20191029114905.6856-3-jfreimann@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This adds support for hiding a device to the qbus and qdev APIs. The
first user of this will be the virtio-net failover feature but the API
introduced with this patch could be used to implement other features as
well, for example hiding pci devices when a pci bus is powered off.
qdev_device_add() is modified to check for a failover_pair_id
argument in the option string. A DeviceListener callback
should_be_hidden() is added. It can be used by a standby device to
inform qdev that this device should not be added now. The standby device
handler can store the device options to plug the device in at a later
point in time.
One reason for hiding the device is that we don't want to expose both
devices to the guest kernel until the respective virtio feature bit
VIRTIO_NET_F_STANDBY was negotiated and we know that the devices will be
handled correctly by the guest.
More information on the kernel feature this is using:
https://www.kernel.org/doc/html/latest/networking/net_failover.html
An example where the primary device is a vfio-pci device and the standby
device is a virtio-net device:
A device is hidden when it has an "failover_pair_id" option, e.g.
-device virtio-net-pci,...,failover=on,...
-device vfio-pci,...,failover_pair_id=net1,...
Signed-off-by: Jens Freimann <jfreimann@redhat.com>
Message-Id: <20191029114905.6856-2-jfreimann@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Version: GnuPG v1
iQEcBAABAgAGBQJdt6UAAAoJEO8Ells5jWIRdaAH/3+dufJuFijZY44VYbob92ud
lZR1dYah1fBL1bq0F2siFUb+/wgF1IXHJl9tuUJe8Kp0+hnsXji2s4Iuq5lNQoJj
wwMGziL1TPkhxwgy4jObIC+/bqZVrzAO4Cd+PARrSGAAbAqjxLPizOaf72/t4kdn
C2n87ZlR5k0EOPmUY6Y2DtHtrJ20usSS6EThGhdW7iPSzfQSGiOdRzfZrSiEV2XT
cuKbSzQxk7pbPcz4jIgLzaoA7FIXwm99dBosUkjPszNNFbO4+OPDNdUBanYuqmn/
0ZPe/9YZpEMV64ps/Ab7lx7YB04wZ+A9Etln2JULhBWXg/oyri9gsqgOc6bfCXg=
=uE5S
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/jasowang/tags/net-pull-request' into staging
# gpg: Signature made Tue 29 Oct 2019 02:33:36 GMT
# gpg: using RSA key EF04965B398D6211
# gpg: Good signature from "Jason Wang (Jason Wang on RedHat) <jasowang@redhat.com>" [marginal]
# gpg: WARNING: This key is not certified with sufficiently trusted signatures!
# gpg: It is not certain that the signature belongs to the owner.
# Primary key fingerprint: 215D 46F4 8246 689E C77F 3562 EF04 965B 398D 6211
* remotes/jasowang/tags/net-pull-request:
COLO-compare: Fix incorrect `if` logic
virtio-net: prevent offloads reset on migration
virtio: new post_load hook
net: add tulip (dec21143) driver
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Currently offloads disabled by guest via the VIRTIO_NET_CTRL_GUEST_OFFLOADS_SET
command are not preserved on VM migration.
Instead all offloads reported by guest features (via VIRTIO_PCI_GUEST_FEATURES)
get enabled.
What happens is: first the VirtIONet::curr_guest_offloads gets restored and offloads
are getting set correctly:
#0 qemu_set_offload (nc=0x555556a11400, csum=1, tso4=0, tso6=0, ecn=0, ufo=0) at net/net.c:474
#1 virtio_net_apply_guest_offloads (n=0x555557701ca0) at hw/net/virtio-net.c:720
#2 virtio_net_post_load_device (opaque=0x555557701ca0, version_id=11) at hw/net/virtio-net.c:2334
#3 vmstate_load_state (f=0x5555569dc010, vmsd=0x555556577c80 <vmstate_virtio_net_device>, opaque=0x555557701ca0, version_id=11)
at migration/vmstate.c:168
#4 virtio_load (vdev=0x555557701ca0, f=0x5555569dc010, version_id=11) at hw/virtio/virtio.c:2197
#5 virtio_device_get (f=0x5555569dc010, opaque=0x555557701ca0, size=0, field=0x55555668cd00 <__compound_literal.5>) at hw/virtio/virtio.c:2036
#6 vmstate_load_state (f=0x5555569dc010, vmsd=0x555556577ce0 <vmstate_virtio_net>, opaque=0x555557701ca0, version_id=11) at migration/vmstate.c:143
#7 vmstate_load (f=0x5555569dc010, se=0x5555578189e0) at migration/savevm.c:829
#8 qemu_loadvm_section_start_full (f=0x5555569dc010, mis=0x5555569eee20) at migration/savevm.c:2211
#9 qemu_loadvm_state_main (f=0x5555569dc010, mis=0x5555569eee20) at migration/savevm.c:2395
#10 qemu_loadvm_state (f=0x5555569dc010) at migration/savevm.c:2467
#11 process_incoming_migration_co (opaque=0x0) at migration/migration.c:449
However later on the features are getting restored, and offloads get reset to
everything supported by features:
#0 qemu_set_offload (nc=0x555556a11400, csum=1, tso4=1, tso6=1, ecn=0, ufo=0) at net/net.c:474
#1 virtio_net_apply_guest_offloads (n=0x555557701ca0) at hw/net/virtio-net.c:720
#2 virtio_net_set_features (vdev=0x555557701ca0, features=5104441767) at hw/net/virtio-net.c:773
#3 virtio_set_features_nocheck (vdev=0x555557701ca0, val=5104441767) at hw/virtio/virtio.c:2052
#4 virtio_load (vdev=0x555557701ca0, f=0x5555569dc010, version_id=11) at hw/virtio/virtio.c:2220
#5 virtio_device_get (f=0x5555569dc010, opaque=0x555557701ca0, size=0, field=0x55555668cd00 <__compound_literal.5>) at hw/virtio/virtio.c:2036
#6 vmstate_load_state (f=0x5555569dc010, vmsd=0x555556577ce0 <vmstate_virtio_net>, opaque=0x555557701ca0, version_id=11) at migration/vmstate.c:143
#7 vmstate_load (f=0x5555569dc010, se=0x5555578189e0) at migration/savevm.c:829
#8 qemu_loadvm_section_start_full (f=0x5555569dc010, mis=0x5555569eee20) at migration/savevm.c:2211
#9 qemu_loadvm_state_main (f=0x5555569dc010, mis=0x5555569eee20) at migration/savevm.c:2395
#10 qemu_loadvm_state (f=0x5555569dc010) at migration/savevm.c:2467
#11 process_incoming_migration_co (opaque=0x0) at migration/migration.c:449
Fix this by preserving the state in saved_guest_offloads field and
pushing out offload initialization to the new post load hook.
Cc: qemu-stable@nongnu.org
Signed-off-by: Mikhail Sennikovsky <mikhail.sennikovskii@cloud.ionos.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Post load hook in virtio vmsd is called early while device is processed,
and when VirtIODevice core isn't fully initialized. Most device
specific code isn't ready to deal with a device in such state, and
behaves weirdly.
Add a new post_load hook in a device class instead. Devices should use
this unless they specifically want to verify the migration stream as
it's processed, e.g. for bounds checking.
Cc: qemu-stable@nongnu.org
Suggested-by: "Dr. David Alan Gilbert" <dgilbert@redhat.com>
Cc: Mikhail Sennikovsky <mikhail.sennikovskii@cloud.ionos.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
This adds the basic functionality to emulate a Tulip NIC.
Implemented are:
- RX and TX functionality
- Perfect Frame Filtering
- Big/Little Endian descriptor support
- 93C46 EEPROM support
- LXT970 PHY
Not implemented, mostly because i had no OS using these functions:
- Imperfect frame filtering
- General Purpose Timer
- Transmit automatic polling
- Boot ROM support
- SIA interface
- Big/Little Endian data buffer conversion
Successfully tested with the following Operating Systems:
- MSDOS with Microsoft Network Client 3.0 and DEC ODI drivers
- HPPA Linux
- Windows XP
- HP-UX
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Message-Id: <20191022155413.4619-1-svens@stackframe.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Jason Wang <jasowang@redhat.com>
This patch set contains a handful of small fixes for RISC-V targets that
I'd like to target for the 4.2 soft freeze. They include:
* A fix to allow the debugger to access the state of all privilege
modes, as opposed to just the currently executing one.
* A pair of cleanups to implement cpu_do_transaction_failed.
* Fixes to the device tree.
* The addition of various memory regions to make the sifive_u machine
more closely match the HiFive Unleashed board.
* Fixes to our GDB interface to allow CSRs to be accessed.
* A fix to a memory leak pointed out by coverity.
* A fix that prevents PMP checks from firing incorrectly.
This passes "make chcek" and boots Open Embedded for me.
-----BEGIN PGP SIGNATURE-----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=e4jZ
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/palmer/tags/riscv-for-master-4.2-sf2' into staging
RISC-V Patches for the 4.2 Soft Freeze, Part 2
This patch set contains a handful of small fixes for RISC-V targets that
I'd like to target for the 4.2 soft freeze. They include:
* A fix to allow the debugger to access the state of all privilege
modes, as opposed to just the currently executing one.
* A pair of cleanups to implement cpu_do_transaction_failed.
* Fixes to the device tree.
* The addition of various memory regions to make the sifive_u machine
more closely match the HiFive Unleashed board.
* Fixes to our GDB interface to allow CSRs to be accessed.
* A fix to a memory leak pointed out by coverity.
* A fix that prevents PMP checks from firing incorrectly.
This passes "make chcek" and boots Open Embedded for me.
# gpg: Signature made Mon 28 Oct 2019 15:47:52 GMT
# gpg: using RSA key 00CE76D1834960DFCE886DF8EF4CA1502CCBAB41
# gpg: issuer "palmer@dabbelt.com"
# gpg: Good signature from "Palmer Dabbelt <palmer@dabbelt.com>" [unknown]
# gpg: aka "Palmer Dabbelt <palmer@sifive.com>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 00CE 76D1 8349 60DF CE88 6DF8 EF4C A150 2CCB AB41
* remotes/palmer/tags/riscv-for-master-4.2-sf2:
target/riscv: PMP violation due to wrong size parameter
riscv/boot: Fix possible memory leak
target/riscv: Make the priv register writable by GDB
target/riscv: Expose "priv" register for GDB for reads
target/riscv: Tell gdbstub the correct number of CSRs
riscv/virt: Jump to pflash if specified
riscv/virt: Add the PFlash CFI01 device
riscv/virt: Manually define the machine
riscv/sifive_u: Add the start-in-flash property
riscv/sifive_u: Manually define the machine
riscv/sifive_u: Add QSPI memory region
riscv/sifive_u: Add L2-LIM cache memory
linux-user/riscv: Propagate fault address
riscv: sifive_u: Add ethernet0 to the aliases node
riscv: hw: Drop "clock-frequency" property of cpu nodes
RISC-V: Implement cpu_do_transaction_failed
RISC-V: Handle bus errors in the page table walker
riscv: Skip checking CSR privilege level in debugger mode
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
SWIM (Sander-Wozniak Integrated Machine) is the floppy controller of
the 680x0 Macintosh.
This patch introduces only the basic support: it allows to switch from
IWM (Integrated WOZ Machine) mode to the SWIM mode and makes the linux
driver happy.
It cannot read any floppy image.
Co-developed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Hervé Poussineau <hpoussin@reactos.org>
Message-Id: <20191026164546.30020-10-laurent@vivier.eu>
This patch adds support for a graphic framebuffer device.
This device can be added as a sysbus device or as a NuBus device.
It is accessed as a framebuffer but the color palette can be set.
Co-developed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Hervé Poussineau <hpoussin@reactos.org>
Reviewed-by: Thomas Huth <huth@tuxfamily.org>
Message-Id: <20191026164546.30020-9-laurent@vivier.eu>
This patch adds basic support for the NuBus bus. This is used by 680x0
Macintosh.
Co-developed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Thomas Huth <huth@tuxfamily.org>
Message-Id: <20191026164546.30020-8-laurent@vivier.eu>
VIA needs to be able to poll the ADB interface and to read/write data
from/to the bus.
This patch adds functions allowing that.
Co-developed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Hervé Poussineau <hpoussin@reactos.org>
Reviewed-by: Thomas Huth <huth@tuxfamily.org>
Message-Id: <20191026164546.30020-7-laurent@vivier.eu>
Inside the 680x0 Macintosh, VIA (Versatile Interface Adapter) is used
to interface the keyboard, Mouse, and real-time clock. It also provides
control line for the floppy disk driver, video interface, sound circuitry
and serial interface.
This implementation is based on the MOS6522 object.
Co-developed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Hervé Poussineau <hpoussin@reactos.org>
Message-Id: <20191026164546.30020-6-laurent@vivier.eu>
There is no DMA in Quadra 800, so the CPU reads/writes the data from the
PDMA register (offset 0x100, ESP_PDMA in hw/m68k/q800.c) and copies them
to/from the memory.
There is a nice assembly loop in the kernel to do that, see
linux/drivers/scsi/mac_esp.c:MAC_ESP_PDMA_LOOP().
The start of the transfer is triggered by the DREQ interrupt (see linux
mac_esp_send_pdma_cmd()), the CPU polls on the IRQ flag to start the
transfer after a SCSI command has been sent (in Quadra 800 it goes
through the VIA2, the via2-irq line and the vIFR register)
The Macintosh hardware includes hardware handshaking to prevent the CPU
from reading invalid data or writing data faster than the peripheral
device can accept it.
This is the "blind mode", and from the doc:
"Approximate maximum SCSI transfer rates within a blocks are 1.4 MB per
second for blind transfers in the Macintosh II"
Some references can be found in:
Apple Macintosh Family Hardware Reference, ISBN 0-201-19255-1
Guide to the Macintosh Family Hardware, ISBN-0-201-52405-8
Acked-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Co-developed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20191026164546.30020-4-laurent@vivier.eu>
This gets around a build problem with --disable-tcg.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Having the plugins grab stdout and spew stuff there is a bit ugly and
certainly makes the tests look ugly. Provide a hook back into QEMU
which can be redirected as needed.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Aaron Lindsay <aaron@os.amperecomputing.com>
Give the plugins access to the QEMU dissasembler so they don't have to
re-invent the wheel. We generate a warning when there are spare bytes
in the decode buffer. This is usually due to the front end loading in
more bytes than decoded.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
This provides a limited amount of info to plugins about the guest
system that will allow them to make some additional decisions on
setup.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
We don't bother with replicating the fast path (tlb_hit) of the old
cpu_ldst helpers as it has no measurable effect on performance. This
probably indicates we should consider flattening the whole set of
helpers but that is out of scope for this change.
Suggested-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Emilio G. Cota <cota@braap.org>
[AJB: directly plumb into softmmu/user helpers]
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
We document this in docs/devel/load-stores.rst so lets follow it. The
32 bit and 64 bit access functions have historically not included the
sign so we leave those as is. We also introduce some signed helpers
which are used for loading immediate values in the translator.
Fixes: 282dffc8
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20191021150910.23216-1-alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
By adding it to plugin-gen's header file, we can export is as
an inline, since tcg.h is included in the header (we need tcg_ctx).
Signed-off-by: Emilio G. Cota <cota@braap.org>
[AJB: use g_byte_array]
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
To avoid too much duplication add a wrapper that the existing trace
and the new plugin calls can live in. We could move the -strace code
here as well but that is left for a future series as the code is
subtly different between the bsd and linux.
Signed-off-by: Emilio G. Cota <cota@braap.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
[AJB: wrap in syscall-trace.h, expand commit msg]
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
We need to keep a local per-cpu copy of the data as other threads may
be running. Currently we can provide insight as to if the access was
IO or not and give the offset into a given device (usually the main
RAMBlock). We store enough information to get details such as the
MemoryRegion which might be useful in later expansions to the API.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
To capture all memory accesses we need hook into all the various
helper functions that are involved in memory operations as well as the
injected inline helper calls. A later commit will allow us to resolve
the actual guest HW addresses by replaying the lookup.
Signed-off-by: Emilio G. Cota <cota@braap.org>
[AJB: drop haddr handling, just deal in vaddr]
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
We first inject empty instrumentation from translator_loop.
After translation, we go through the plugins to see what
they want to register for, filling in the empty instrumentation.
If if turns out that some instrumentation remains unused, we
remove it.
This approach supports the following features:
- Inlining TCG code for simple operations. Note that we do not
export TCG ops to plugins. Instead, we give them a C API to
insert inlined ops. So far we only support adding an immediate
to a u64, e.g. to count events.
- "Direct" callbacks. These are callbacks that do not go via
a helper. Instead, the helper is defined at run-time, so that
the plugin code is directly called from TCG. This makes direct
callbacks as efficient as possible; they are therefore used
for very frequent events, e.g. memory callbacks.
- Passing the host address to memory callbacks. Most of this
is implemented in a later patch though.
- Instrumentation of memory accesses performed from helpers.
See the corresponding comment, as well as a later patch.
Signed-off-by: Emilio G. Cota <cota@braap.org>
[AJB: add alloc_tcg_plugin_context, use glib, rm hwaddr]
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
This will be used by plugins to get the host address
of instructions.
Signed-off-by: Emilio G. Cota <cota@braap.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Suggested-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Emilio G. Cota <cota@braap.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
This is faster than removing elements one by one.
Will gain a user soon.
Signed-off-by: Emilio G. Cota <cota@braap.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
[AJB: split from the core code commit]
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Emilio G. Cota <cota@braap.org>
[AJB: moved directory and merged various fixes]
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Add the API first to ease review.
Signed-off-by: Emilio G. Cota <cota@braap.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Suggested-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Emilio G. Cota <cota@braap.org>
[AJB: moved inside start/end_exclusive fns + cleanup]
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
We are going to re-use mem_info later for plugins and will need to
track the mmu_idx for softmmu code.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Add the CFI01 PFlash to the RISC-V virt board. This is the same PFlash
from the ARM Virt board and the implementation is based on the ARM Virt
board. This allows users to specify flash files from the command line.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Instead of using the DEFINE_MACHINE() macro to define the machine let's
do it manually. This allows us to use the machine object to create
RISCVVirtState. This is required to add children and aliases to the
machine.
This patch is no functional change.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Add a property that when set to true QEMU will jump from the ROM code to
the start of flash memory instead of DRAM which is the default
behaviour.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Instead of using the DEFINE_MACHINE() macro to define the machine let's
do it manually. This allows us to specify machine properties.
This patch is no functional change.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
The HiFive Unleashed uses is25wp256 SPI NOR flash. There is currently no
model of this in QEMU, so to allow boot firmware developers to use QEMU
to target the Unleashed let's add a chunk of memory to represent the QSPI0
memory mapped flash. This can be targeted using QEMU's -device loader
command line option.
In the future we can look at adding a model for the is25wp256 flash.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
On reset only a single L2 cache way is enabled, the others are exposed
as memory that can be used by early boot firmware. This L2 region is
generally disabled using the WayEnable register at a later stage in the
boot process. To allow firmware to target QEMU and the HiFive Unleashed
let's add the L2 LIM (LooselyIntegrated Memory).
Ideally we would want to adjust the size of this chunk of memory as the
L2 Cache Controller WayEnable register is incremented. Unfortunately I
don't see a nice way to handle reducing or blocking out the L2 LIM while
still allowing it be re returned to all enabled from a reset.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
The "clock-frequency" property of cpu nodes isn't required. Drop it.
This is to keep in sync with Linux kernel commit below:
https://patchwork.kernel.org/patch/11133031/
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
- iotest patches
- Improve performance of the mirror block job in write-blocking mode
- Limit memory usage for the backup block job
- Add discard and write-zeroes support to the NVMe host block driver
- Fix a bug in the mirror job
- Prevent the qcow2 driver from creating technically non-compliant qcow2
v3 images (where there is not enough extra data for snapshot table
entries)
- Allow callers of bdrv_truncate() (etc.) to determine whether the file
must be resized to the exact given size or whether it is OK for block
devices not to shrink
-----BEGIN PGP SIGNATURE-----
iQFGBAABCAAwFiEEkb62CjDbPohX0Rgp9AfbAGHVz0AFAl2224ESHG1yZWl0ekBy
ZWRoYXQuY29tAAoJEPQH2wBh1c9AeXMH/RXKEX4BZYMRKCe41P18tJC9Bl2x0T20
YeOsZVvpARlr7o/36BF2kGFF4MnL0OQ+9ELuyROX865rk/VL2rWqnHDE5oQM889a
dFwMs+0zvNbig3iLNcw0H5OkE2mrdM+a1EUdn/lBe/39Z8dPqPxRGqIYHq38Ugdu
emwSy1nWen7o0f71HRJfyVtI3KcrzXx71FrA/FY2yL/eHz+zRYGZj2SpAdFPkXP/
lgaz+m0tWhnSW1QzEOXB0Gh69ULt/DczCinYmv5qUY1noW5TPPtiDNCQTts5O4ba
oJsR3AJv5/l9m65JTmiyQSqnQfPcstrQ5FqOcSnP637cfqUFyWsvdks=
=L7v1
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/maxreitz/tags/pull-block-2019-10-28' into staging
Block patches for softfreeze:
- iotest patches
- Improve performance of the mirror block job in write-blocking mode
- Limit memory usage for the backup block job
- Add discard and write-zeroes support to the NVMe host block driver
- Fix a bug in the mirror job
- Prevent the qcow2 driver from creating technically non-compliant qcow2
v3 images (where there is not enough extra data for snapshot table
entries)
- Allow callers of bdrv_truncate() (etc.) to determine whether the file
must be resized to the exact given size or whether it is OK for block
devices not to shrink
# gpg: Signature made Mon 28 Oct 2019 12:13:53 GMT
# gpg: using RSA key 91BEB60A30DB3E8857D11829F407DB0061D5CF40
# gpg: issuer "mreitz@redhat.com"
# gpg: Good signature from "Max Reitz <mreitz@redhat.com>" [full]
# Primary key fingerprint: 91BE B60A 30DB 3E88 57D1 1829 F407 DB00 61D5 CF40
* remotes/maxreitz/tags/pull-block-2019-10-28: (69 commits)
qemu-iotests: restrict 264 to qcow2 only
Revert "qemu-img: Check post-truncation size"
block: Pass truncate exact=true where reasonable
block: Let format drivers pass @exact
block: Evaluate @exact in protocol drivers
block: Add @exact parameter to bdrv_co_truncate()
block: Do not truncate file node when formatting
block/cor: Drop cor_co_truncate()
block: Handle filter truncation like native impl.
iotests: Test qcow2's snapshot table handling
iotests: Add peek_file* functions
qcow2: Fix v3 snapshot table entry compliancy
qcow2: Repair snapshot table with too many entries
qcow2: Fix overly long snapshot tables
qcow2: Keep track of the snapshot table length
qcow2: Fix broken snapshot table entries
qcow2: Add qcow2_check_fix_snapshot_table()
qcow2: Separate qcow2_check_read_snapshot_table()
qcow2: Write v3-compliant snapshot list on upgrade
qcow2: Put qcow2_upgrade() into its own function
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
libqos update with support for virtio 1.
Packed ring support for virtio.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJdsuDvAAoJECgfDbjSjVRpIP8H/3rHSvZ5+MQGCFLI5GU8m3za
JSOaBSmtcj9KwrpibBfptSCJZNrG8EUVHyo+Z+pvGohXqDB8h9RyBfb6vID8jqzC
5wIzlNBP27F668MUBt2t7xSwK0PWO1QOpEKk6S4SJMpl51ea8ePlTH0jnLVfkaAN
hFKU1wqwc2gMyF9rDjOZ6I+OO1iQbMcrsazFrCXECXCkxDcJM0ey7MheKxVntTjt
0sxFHM2I1A+vXtAzlLo6rS3I9vJ0ATfLfOlZLqrq5uSAL5FKrqsbmGh4sAsFTQAA
eerR6zDz3X+YqfQaVgVk2wixPHQz2w8Rv68j6SiGrdZ29/JT6nVWHT8cGtPsX4c=
=iJuG
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
virtio: features, tests
libqos update with support for virtio 1.
Packed ring support for virtio.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Fri 25 Oct 2019 12:47:59 BST
# gpg: using RSA key 281F0DB8D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>" [full]
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>" [full]
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* remotes/mst/tags/for_upstream: (25 commits)
virtio: drop unused virtio_device_stop_ioeventfd() function
libqos: add VIRTIO PCI 1.0 support
libqos: extract Legacy virtio-pci.c code
libqos: make the virtio-pci BAR index configurable
libqos: expose common virtqueue setup/cleanup functions
libqos: add MSI-X callbacks to QVirtioPCIDevice
libqos: pass full QVirtQueue to set_queue_address()
libqos: add iteration support to qpci_find_capability()
libqos: access VIRTIO 1.0 vring in little-endian
libqos: implement VIRTIO 1.0 FEATURES_OK step
libqos: enforce Device Initialization order
libqos: add missing virtio-9p feature negotiation
tests/virtio-blk-test: set up virtqueue after feature negotiation
virtio-scsi-test: add missing feature negotiation
libqos: extend feature bits to 64-bit
libqos: read QVIRTIO_MMIO_VERSION register
tests/virtio-blk-test: read config space after feature negotiation
virtio: add property to enable packed virtqueue
vhost_net: enable packed ring support
virtio: event suppression support for packed ring
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We have two drivers (iscsi and file-posix) that (in some cases) return
success from their .bdrv_co_truncate() implementation if the block
device is larger than the requested offset, but cannot be shrunk. Some
callers do not want that behavior, so this patch adds a new parameter
that they can use to turn off that behavior.
This patch just adds the parameter and lets the block/io.c and
block/block-backend.c functions pass it around. All other callers
always pass false and none of the implementations evaluate it, so that
this patch does not change existing behavior. Future patches take care
of that.
Suggested-by: Maxim Levitsky <mlevitsk@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
Message-id: 20190918095144.955-5-mreitz@redhat.com
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
endof() is a useful macro, we can make use of it outside of virtio.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-id: 20191011152814.14791-2-mreitz@redhat.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
