This patch enables postcopy-preempt feature.
It contains two major changes to the migration logic:
(1) Postcopy requests are now sent via a different socket from precopy
background migration stream, so as to be isolated from very high page
request delays.
(2) For huge page enabled hosts: when there's postcopy requests, they can now
intercept a partial sending of huge host pages on src QEMU.
After this patch, we'll live migrate a VM with two channels for postcopy: (1)
PRECOPY channel, which is the default channel that transfers background pages;
and (2) POSTCOPY channel, which only transfers requested pages.
There's no strict rule of which channel to use, e.g., if a requested page is
already being transferred on precopy channel, then we will keep using the same
precopy channel to transfer the page even if it's explicitly requested. In 99%
of the cases we'll prioritize the channels so we send requested page via the
postcopy channel as long as possible.
On the source QEMU, when we found a postcopy request, we'll interrupt the
PRECOPY channel sending process and quickly switch to the POSTCOPY channel.
After we serviced all the high priority postcopy pages, we'll switch back to
PRECOPY channel so that we'll continue to send the interrupted huge page again.
There's no new thread introduced on src QEMU.
On the destination QEMU, one new thread is introduced to receive page data from
the postcopy specific socket (done in the preparation patch).
This patch has a side effect: after sending postcopy pages, previously we'll
assume the guest will access follow up pages so we'll keep sending from there.
Now it's changed. Instead of going on with a postcopy requested page, we'll go
back and continue sending the precopy huge page (which can be intercepted by a
postcopy request so the huge page can be sent partially before).
Whether that's a problem is debatable, because "assuming the guest will
continue to access the next page" may not really suite when huge pages are
used, especially if the huge page is large (e.g. 1GB pages). So that locality
hint is much meaningless if huge pages are used.
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20220707185504.27203-1-peterx@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Create a new socket for postcopy to be prepared to send postcopy requested
pages via this specific channel, so as to not get blocked by precopy pages.
A new thread is also created on dest qemu to receive data from this new channel
based on the ram_load_postcopy() routine.
The ram_load_postcopy(POSTCOPY) branch and the thread has not started to
function, and that'll be done in follow up patches.
Cleanup the new sockets on both src/dst QEMUs, meanwhile look after the new
thread too to make sure it'll be recycled properly.
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20220707185502.27149-1-peterx@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
dgilbert: With Peter's fix to quieten compiler warning on
start_migration
Firstly, postcopy already preempts precopy due to the fact that we do
unqueue_page() first before looking into dirty bits.
However that's not enough, e.g., when there're host huge page enabled, when
sending a precopy huge page, a postcopy request needs to wait until the whole
huge page that is sending to finish. That could introduce quite some delay,
the bigger the huge page is the larger delay it'll bring.
This patch adds a new capability to allow postcopy requests to preempt existing
precopy page during sending a huge page, so that postcopy requests can be
serviced even faster.
Meanwhile to send it even faster, bypass the precopy stream by providing a
standalone postcopy socket for sending requested pages.
Since the new behavior will not be compatible with the old behavior, this will
not be the default, it's enabled only when the new capability is set on both
src/dst QEMUs.
This patch only adds the capability itself, the logic will be added in follow
up patches.
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20220707185342.26794-2-peterx@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Now that all QEMUFile callbacks are removed, the entire concept can be
deleted.
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
The name 'ftell' gives the misleading impression that the QEMUFile
objects are seekable. This is not the case, as in general we just
have an opaque stream. The users of this method are only interested
in the total bytes processed. This switches to a new name that
reflects the intended usage.
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
dgilbert: Wrapped long line
When originally implemented, zero_copy_send was designed as a Migration
paramenter.
But taking into account how is that supposed to work, and how
the difference between a capability and a parameter, it only makes sense
that zero-copy-send would work better as a capability.
Taking into account how recently the change got merged, it was decided
that it's still time to make it right, and convert zero_copy_send into
a Migration capability.
Signed-off-by: Leonardo Bras <leobras@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Acked-by: Markus Armbruster <armbru@redhat.com>
Acked-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
dgilbert: always define the capability, even on non-Linux but error if
set; avoids build problems with the capability
Implement zero copy send on nocomp_send_write(), by making use of QIOChannel
writev + flags & flush interface.
Change multifd_send_sync_main() so flush_zero_copy() can be called
after each iteration in order to make sure all dirty pages are sent before
a new iteration is started. It will also flush at the beginning and at the
end of migration.
Also make it return -1 if flush_zero_copy() fails, in order to cancel
the migration process, and avoid resuming the guest in the target host
without receiving all current RAM.
This will work fine on RAM migration because the RAM pages are not usually freed,
and there is no problem on changing the pages content between writev_zero_copy() and
the actual sending of the buffer, because this change will dirty the page and
cause it to be re-sent on a next iteration anyway.
A lot of locked memory may be needed in order to use multifd migration
with zero-copy enabled, so disabling the feature should be necessary for
low-privileged users trying to perform multifd migrations.
Signed-off-by: Leonardo Bras <leobras@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Message-Id: <20220513062836.965425-9-leobras@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
A lot of places check parameters.tls_creds in order to evaluate if TLS is
in use, and sometimes call migrate_get_current() just for that test.
Add new helper function migrate_use_tls() in order to simplify testing
for TLS usage.
Signed-off-by: Leonardo Bras <leobras@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Message-Id: <20220513062836.965425-6-leobras@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Add property that allows zero-copy migration of memory pages
on the sending side, and also includes a helper function
migrate_use_zero_copy_send() to check if it's enabled.
No code is introduced to actually do the migration, but it allow
future implementations to enable/disable this feature.
On non-Linux builds this parameter is compiled-out.
Signed-off-by: Leonardo Bras <leobras@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Acked-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20220513062836.965425-5-leobras@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
The 'status' field for the migration is updated normally using
an atomic operation from the migration thread.
Most readers of it aren't that careful, and in most cases it doesn't
matter.
In query_migrate->fill_source_migration_info the 'state'
is read twice; the first time to decide which state fields to fill in,
and then secondly to copy the state to the status field; that can end up
with a status that's inconsistent; e.g. setting up the fields
for 'setup' and then having an 'active' status. In that case
libvirt gets upset by the lack of ram info.
The symptom is:
libvirt.libvirtError: internal error: migration was active, but no RAM info was set
Read the state exactly once in fill_source_migration_info.
This is a possible fix for:
https://bugzilla.redhat.com/show_bug.cgi?id=2074205
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20220413113329.103696-1-dgilbert@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Previously migration didn't have an easy way to cleanup the listening
transport, migrate recovery only allows to execute once. That's done with a
trick flag in postcopy_recover_triggered.
Now the facility is already there.
Drop postcopy_recover_triggered and instead allows a new migrate-recover to
release the previous listener transport.
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20220331150857.74406-8-peterx@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
We used to use postcopy_try_recover() to replace migration_incoming_setup() to
setup incoming channels. That's fine for the old world, but in the new world
there can be more than one channels that need setup. Better move the channel
setup out of it so that postcopy_try_recover() only handles the last phase of
switching to the recovery phase.
To do that in migration_fd_process_incoming(), move the postcopy_try_recover()
call to be after migration_incoming_setup(), which will setup the channels.
While in migration_ioc_process_incoming(), postpone the recover() routine right
before we'll jump into migration_incoming_process().
A side benefit is we don't need to pass in QEMUFile* to postcopy_try_recover()
anymore. Remove it.
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20220331150857.74406-7-peterx@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
This variable, along with its helpers, is used to detect whether multiple
channel will be supported for migration. In follow up patches, there'll be
other capability that requires multi-channels. Hence move it outside multifd
specific code and make it public. Meanwhile rename it from "multifd" to
"multi_channels" to show its real meaning.
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20220331150857.74406-5-peterx@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
We used to release it right after migrate_fd_connect(). That's not good
enough when there're more than one socket pair required, because it'll be
needed to establish TLS connection for the rest channels.
One example is multifd, where we copied over the hostname for each channel
but that's actually not needed.
Keeping the hostname until the cleanup phase of migration.
Cc: Daniel P. Berrange <berrange@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20220331150857.74406-2-peterx@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
dgilbert: Fixup checkpatch error; don't need to check for NULL
around g_free
Replace the global variables with inlined helper functions. getpagesize() is very
likely annotated with a "const" function attribute (at least with glibc), and thus
optimization should apply even better.
This avoids the need for a constructor initialization too.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20220323155743.1585078-12-marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Following the bdrv_activate renaming, change also the name
of the respective callers.
bdrv_invalidate_cache_all -> bdrv_activate_all
blk_invalidate_cache -> blk_activate
test_sync_op_invalidate_cache -> test_sync_op_activate
No functional change intended.
Signed-off-by: Emanuele Giuseppe Esposito <eesposit@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Hanna Reitz <hreitz@redhat.com>
Message-Id: <20220209105452.1694545-5-eesposit@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Add a helper to cleanup the transport listener.
When do it, we should also null-ify the cleanup hook and the data, then it's
even safe to call it multiple times.
Move the socket_address_list cleanup altogether, because that's a mirror of the
listener channels and only for the purpose of query-migrate. Hence when
someone wants to cleanup the listener transport, it should also want to cleanup
the socket list too, always.
No functional change intended.
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20220301083925.33483-15-peterx@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
We used to have quite a few places making sure -EIO happened and that's the
only way to trigger postcopy recovery. That's based on the assumption that
we'll only return -EIO for channel issues.
It'll work in 99.99% cases but logically that won't cover some corner cases.
One example is e.g. ram_block_from_stream() could fail with an interrupted
network, then -EINVAL will be returned instead of -EIO.
I remembered Dave Gilbert pointed that out before, but somehow this is
overlooked. Neither did I encounter anything outside the -EIO error.
However we'd better touch that up before it triggers a rare VM data loss during
live migrating.
To cover as much those cases as possible, remove the -EIO restriction on
triggering the postcopy recovery, because even if it's not a channel failure,
we can't do anything better than halting QEMU anyway - the corpse of the
process may even be used by a good hand to dig out useful memory regions, or
the admin could simply kill the process later on.
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20220301083925.33483-11-peterx@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Provide information on the number of bytes copied in the pre-copy,
downtime and post-copy phases of migration.
Signed-off-by: David Edmondson <david.edmondson@oracle.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
It will just never fail. Drop those return values where they're constantly
zeros.
A tiny touch-up on the tracepoint so trace_ram_postcopy_send_discard_bitmap()
is called after the logic itself (which sounds more reasonable).
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
The MIGRATION_STATUS_ACTIVE indicates that migration is running.
Remove it to be handled by the default operation,
It should be part of the unknown ending states.
Signed-off-by: Zhang Chen <chen.zhang@intel.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
COLO dose not support postcopy migration and remove the Fixme.
Signed-off-by: Zhang Chen <chen.zhang@intel.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
In the migration_completion() no other status is expected, for
example MIGRATION_STATUS_CANCELLING, MIGRATION_STATUS_CANCELLED, etc.
Signed-off-by: Zhang Chen <chen.zhang@intel.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
virtio-net-failover test tries several device combinations that produces
some expected warnings.
These warning can be confusing, so we disable them during the qtest
sequence.
Reported-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Message-Id: <20211220145314.390697-1-lvivier@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
[thuth: Fix memory leak by using error_free()]
Signed-off-by: Thomas Huth <thuth@redhat.com>
When the PVM guest poweroff, the COLO thread may wait a semaphore
in colo_process_checkpoint().So, we should wake up the COLO thread
before migration shutdown.
Signed-off-by: Lei Rao <lei.rao@intel.com>
Reviewed-by: Zhang Chen <chen.zhang@intel.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
This patch fixed as follows:
Thread 1 (Thread 0x7f34ee738d80 (LWP 11212)):
#0 __pthread_clockjoin_ex (threadid=139847152957184, thread_return=0x7f30b1febf30, clockid=<optimized out>, abstime=<optimized out>, block=<optimized out>) at pthread_join_common.c:145
#1 0x0000563401998e36 in qemu_thread_join (thread=0x563402d66610) at util/qemu-thread-posix.c:587
#2 0x00005634017a79fa in process_incoming_migration_co (opaque=0x0) at migration/migration.c:502
#3 0x00005634019b59c9 in coroutine_trampoline (i0=63395504, i1=22068) at util/coroutine-ucontext.c:115
#4 0x00007f34ef860660 in ?? () at ../sysdeps/unix/sysv/linux/x86_64/__start_context.S:91 from /lib/x86_64-linux-gnu/libc.so.6
#5 0x00007f30b21ee730 in ?? ()
#6 0x0000000000000000 in ?? ()
Thread 13 (Thread 0x7f30b3dff700 (LWP 11747)):
#0 __lll_lock_wait (futex=futex@entry=0x56340218ffa0 <qemu_global_mutex>, private=0) at lowlevellock.c:52
#1 0x00007f34efa000a3 in _GI__pthread_mutex_lock (mutex=0x56340218ffa0 <qemu_global_mutex>) at ../nptl/pthread_mutex_lock.c:80
#2 0x0000563401997f99 in qemu_mutex_lock_impl (mutex=0x56340218ffa0 <qemu_global_mutex>, file=0x563401b7a80e "migration/colo.c", line=806) at util/qemu-thread-posix.c:78
#3 0x0000563401407144 in qemu_mutex_lock_iothread_impl (file=0x563401b7a80e "migration/colo.c", line=806) at /home/workspace/colo-qemu/cpus.c:1899
#4 0x00005634017ba8e8 in colo_process_incoming_thread (opaque=0x563402d664c0) at migration/colo.c:806
#5 0x0000563401998b72 in qemu_thread_start (args=0x5634039f8370) at util/qemu-thread-posix.c:519
#6 0x00007f34ef9fd609 in start_thread (arg=<optimized out>) at pthread_create.c:477
#7 0x00007f34ef924293 in clone () at ../sysdeps/unix/sysv/linux/x86_64/clone.S:95
The QEMU main thread is holding the lock:
(gdb) p qemu_global_mutex
$1 = {lock = {_data = {lock = 2, __count = 0, __owner = 11212, __nusers = 9, __kind = 0, __spins = 0, __elision = 0, __list = {_prev = 0x0, __next = 0x0}},
__size = "\002\000\000\000\000\000\000\000\314+\000\000\t", '\000' <repeats 26 times>, __align = 2}, file = 0x563401c07e4b "util/main-loop.c", line = 240,
initialized = true}
>From the call trace, we can see it is a deadlock bug. and the QEMU main thread holds the global mutex to wait until the COLO thread ends. and the colo thread
wants to acquire the global mutex, which will cause a deadlock. So, we should release the qemu_global_mutex before waiting colo thread ends.
Signed-off-by: Lei Rao <lei.rao@intel.com>
Reviewed-by: Li Zhijian <lizhijian@cn.fujitsu.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
This patch fixes the following:
qemu-system-x86_64: invalid runstate transition: 'shutdown' -> 'running'
Aborted (core dumped)
The gdb bt as following:
0 __GI_raise (sig=sig@entry=6) at ../sysdeps/unix/sysv/linux/raise.c:50
1 0x00007faa3d613859 in __GI_abort () at abort.c:79
2 0x000055c5a21268fd in runstate_set (new_state=RUN_STATE_RUNNING) at vl.c:723
3 0x000055c5a1f8cae4 in vm_prepare_start () at /home/workspace/colo-qemu/cpus.c:2206
4 0x000055c5a1f8cb1b in vm_start () at /home/workspace/colo-qemu/cpus.c:2213
5 0x000055c5a2332bba in migration_iteration_finish (s=0x55c5a4658810) at migration/migration.c:3376
6 0x000055c5a2332f3b in migration_thread (opaque=0x55c5a4658810) at migration/migration.c:3527
7 0x000055c5a251d68a in qemu_thread_start (args=0x55c5a5491a70) at util/qemu-thread-posix.c:519
8 0x00007faa3d7e9609 in start_thread (arg=<optimized out>) at pthread_create.c:477
9 0x00007faa3d710293 in clone () at ../sysdeps/unix/sysv/linux/x86_64/clone.S:95
Signed-off-by: Lei Rao <lei.rao@intel.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
If the compression migration fails or is canceled, the query for the value of
compression_counters during the next compression migration is wrong.
Signed-off-by: yuxiating <yuxiating@huawei.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
This avoids to call migrate_get_current() in the caller function
whereas migration_cancel() already needs the pointer to the current
migration state.
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Let's use QEMU_ALIGN_DOWN() and friends to make the code a bit easier to
read.
Reviewed-by: Peter Xu <peterx@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
An internal version that removes -only-migratable implications. It can be used
for temporary migration blockers like dump-guest-memory.
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
save_snapshot() checks migration blocker, which looks sane. At the meantime we
should also teach the blocker add helper to fail if during a snapshot, just
like for migrations.
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
To: <quintela@redhat.com>, <dgilbert@redhat.com>, <qemu-devel@nongnu.org>
CC: Li Zhijian <lizhijian@cn.fujitsu.com>
Date: Sat, 31 Jul 2021 22:05:52 +0800 (5 weeks, 4 days, 17 hours ago)
And change the default to true so that in '-incoming defer' case, user is able
to change multifd capability.
Signed-off-by: Li Zhijian <lizhijian@cn.fujitsu.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
To: <quintela@redhat.com>, <dgilbert@redhat.com>, <qemu-devel@nongnu.org>
CC: Li Zhijian <lizhijian@cn.fujitsu.com>
Date: Sat, 31 Jul 2021 22:05:51 +0800 (5 weeks, 4 days, 17 hours ago)
multifd with unsupported protocol will cause a segment fault.
(gdb) bt
#0 0x0000563b4a93faf8 in socket_connect (addr=0x0, errp=0x7f7f02675410) at ../util/qemu-sockets.c:1190
#1 0x0000563b4a797a03 in qio_channel_socket_connect_sync
(ioc=0x563b4d16e8c0, addr=0x0, errp=0x7f7f02675410) at
../io/channel-socket.c:145
#2 0x0000563b4a797abf in qio_channel_socket_connect_worker (task=0x563b4cd86c30, opaque=0x0) at ../io/channel-socket.c:168
#3 0x0000563b4a792631 in qio_task_thread_worker (opaque=0x563b4cd86c30) at ../io/task.c:124
#4 0x0000563b4a91da69 in qemu_thread_start (args=0x563b4c44bb80) at ../util/qemu-thread-posix.c:541
#5 0x00007f7fe9b5b3f9 in ?? ()
#6 0x0000000000000000 in ?? ()
It's enough to check migrate_multifd_is_allowed() in multifd cleanup() and
multifd setup() though there are so many other places using migrate_use_multifd().
Signed-off-by: Li Zhijian <lizhijian@cn.fujitsu.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
qemu_savevm_state_complete_postcopy assumes the iothread lock (BQL)
to be held, but instead it isn't.
Signed-off-by: Emanuele Giuseppe Esposito <eesposit@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20211005080751.3797161-3-eesposit@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Commit b673eab4e2 "multifd: Make multifd_load_setup() get an Error
parameter" changed migration_incoming_setup() to take an Error **
argument, and adjusted the callers accordingly. It neglected to
change adjust multifd_load_setup(): it still exit()s on error. Clean
that up.
The error now gets propagated up two call chains: via
migration_fd_process_incoming() to rdma_accept_incoming_migration(),
and via migration_ioc_process_incoming() to
migration_channel_process_incoming(). Both chain ends report the
error with error_report_err(), but otherwise ignore it. Behavioral
change: we no longer exit() on this error.
This is consistent with how we handle other errors here, e.g. from
multifd_recv_new_channel() via migration_ioc_process_incoming() to
migration_channel_process_incoming(). Whether it's consistently right
or consistently wrong I can't tell.
Also clean up the return value from the unusual 0 on success, 1 on
error to the more common true on success, false on error.
Cc: Juan Quintela <quintela@redhat.com>
Cc: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20210720125408.387910-11-armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Pankaj Gupta <pankaj.gupta@ionos.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
We did this with scripts/coccinelle/use-error_fatal.cocci before, in
commit 50beeb6809 and 007b06578a. This commit cleans up rarer
variations that don't seem worth matching with Coccinelle.
Cc: Thomas Huth <thuth@redhat.com>
Cc: Cornelia Huck <cornelia.huck@de.ibm.com>
Cc: Peter Xu <peterx@redhat.com>
Cc: Juan Quintela <quintela@redhat.com>
Cc: Stefan Hajnoczi <stefanha@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Marc-André Lureau <marcandre.lureau@redhat.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20210720125408.387910-2-armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
It's efficient, but hackish to call yank unregister calls in channel_close(),
especially it'll be hard to debug when qemu crashed with some yank function
leaked.
Remove that hack, but instead explicitly unregister yank functions at the
places where needed, they are:
(on src)
- migrate_fd_cleanup
- postcopy_pause
(on dst)
- migration_incoming_state_destroy
- postcopy_pause_incoming
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20210722175841.938739-6-peterx@redhat.com>
Reviewed-by: Lukas Straub <lukasstraub2@web.de>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Accessing from_dst_file is potentially racy in current code base like below:
if (s->from_dst_file)
do_something(s->from_dst_file);
Because from_dst_file can be reset right after the check in another
thread (rp_thread). One example is migrate_fd_cancel().
Use the same qemu_file_lock to protect it too, just like to_dst_file.
When it's safe to access without lock, comment it.
There's one special reference in migration_thread() that can be replaced by
the newly introduced rp_thread_created flag.
Reported-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Lukas Straub <lukasstraub2@web.de>
Message-Id: <20210722175841.938739-3-peterx@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
with Peter's fixup
It's possible that the migration thread skip the join() of the rp_thread in
below race and crash on src right at finishing migration:
migration_thread rp_thread
---------------- ---------
migration_completion()
(before rp_thread quits)
from_dst_file=NULL
[thread got scheduled out]
s->rp_state.from_dst_file==NULL
(skip join() of rp_thread)
migrate_fd_cleanup()
qemu_fclose(s->to_dst_file)
yank_unregister_instance()
assert(yank_find_entry()) <------- crash
It could mostly happen with postcopy, but that shouldn't be required, e.g., I
think it could also trigger with MIGRATION_CAPABILITY_RETURN_PATH set.
It's suspected that above race could be the root cause of a recent (but rare)
migration-test break reported by either Dave or PMM:
https://lore.kernel.org/qemu-devel/YPamXAHwan%2FPPXLf@work-vm/
The issue is: from_dst_file is reset in the rp_thread, so if the thread reset
it to NULL fast enough then the migration thread will assume there's no
rp_thread at all.
This could potentially cause more severe issue (e.g. crash) after the yank code.
Fix it by using a boolean to keep "whether we've created rp_thread".
Cc: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20210722175841.938739-2-peterx@redhat.com>
Reviewed-by: Lukas Straub <lukasstraub2@web.de>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
For each "migrate" command, remember to clear the s->error before going on.
For one reason, when there's a new error it'll be still remembered; see
migrate_set_error() who only sets the error if error==NULL. Meanwhile if a
failed migration completes (e.g., postcopy recovered and finished), we
shouldn't dump an error when calling migrate_fd_cleanup() at last.
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20210708190653.252961-4-peterx@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Below process could crash qemu with postcopy recovery:
1. (hmp) migrate -d ..
2. (hmp) migrate_start_postcopy
3. [network down, postcopy paused]
4. (hmp) migrate -r $WRONG_PORT
when try the recover on an invalid $WRONG_PORT, cleanup_bh will be cleared
5. (hmp) migrate -r $RIGHT_PORT
[qemu crash on assert(cleanup_bh)]
The thing is we shouldn't cleanup if it's postcopy resume; the error is set
mostly because the channel is wrong, so we return directly waiting for the user
to retry.
migrate_fd_cleanup() should only be called when migration is cancelled or
completed.
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20210708190653.252961-3-peterx@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
When postcopy pause triggered, we rely on the migration thread to cleanup the
to_dst_file handle, and the return path thread to cleanup the from_dst_file
handle (which is stored in the local variable "rp").
Within the process, from_dst_file cleanup (qemu_fclose) is postponed until it's
setup again due to a postcopy recovery.
It used to work before yank was born; after yank is introduced we rely on the
refcount of IOC to correctly unregister yank function in channel_close(). If
without the early and on-time release of from_dst_file handle the yank function
will be leftover during paused postcopy.
Without this patch, below steps (quoted from Xiaohui) could trigger qemu src
crash:
1.Boot vm on src host
2.Boot vm on dst host
3.Enable postcopy on src&dst host
4.Load stressapptest in vm and set postcopy speed to 50M
5.Start migration from src to dst host, change into postcopy mode when migration is active.
6.When postcopy is active, down the network card(do migration via this network) on dst host.
7.Wait untill postcopy is paused on src&dst host.
8.Before up network card, recover migration on dst host, will get error like following.
9.Ignore the error of step 8, go on recovering migration on src host:
After step 9, qemu on src host will core dump after some seconds:
qemu-kvm: ../util/yank.c:107: yank_unregister_instance: Assertion `QLIST_EMPTY(&entry->yankfns)' failed.
1.sh: line 38: 44662 Aborted (core dumped)
Reported-by: Li Xiaohui <xiaohli@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20210708190653.252961-2-peterx@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
When the migration fails or is canceled we wait the end of the unplug
operation to be able to plug it back. But if the unplug operation
is never finished we stop to wait and QEMU emits a warning to inform
the user.
Based-on: 20210629155007.629086-1-lvivier@redhat.com
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Message-Id: <20210701131458.112036-1-lvivier@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
If the user cancels the migration in the unplug-wait state,
QEMU will try to plug back the card and this fails because the card
is partially unplugged.
To avoid the problem, continue to wait the card unplug, but to
allow the migration to be canceled if the card never finishes to unplug
use a timeout.
Bug: https://bugzilla.redhat.com/show_bug.cgi?id=1976852
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20210629155007.629086-3-lvivier@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
The loop is used in migration_thread() and bg_migration_thread(),
so we can move it to its own function and call it from these both places.
Moreover, in migration_thread() we have a wrong state transition from
SETUP to ACTIVE while state could be WAIT_UNPLUG. This is correctly
managed in bg_migration_thread() so use this code instead.
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Message-Id: <20210629155007.629086-2-lvivier@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
It's possible qemu_start_incoming_migration() failed at any point, when it
happens we should reset postcopy_recover_triggered to false so that the user
can still retry with a saner incoming port.
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20210629181356.217312-3-peterx@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Starting from commit b5eea99ec2, qmp_migrate_recover() calls unregister
before calling qemu_start_incoming_migration(). I believe it wanted to mitigate
the next call to yank_register_instance(), but I think that's wrong.
Firstly, if during recover, we should keep the yank instance there, not
"quickly removing and adding it back".
Meanwhile, calling qmp_migrate_recover() twice with b5eea99ec2 will directly
crash the dest qemu (right now it can't; but it'll start to work right after
the next patch) because the 1st call of qmp_migrate_recover() will unregister
permanently when the channel failed to establish, then the 2nd call of
qmp_migrate_recover() crashes at yank_unregister_instance().
This patch fixes it by moving yank ops out of qemu_start_incoming_migration()
into qmp_migrate_incoming. For qmp_migrate_recover(), drop the unregister of
yank instance too since we keep it there during the recovery phase.
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20210629181356.217312-2-peterx@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
This is a critical failure scenario for migration that is hard to
diagnose from existing probes. Most likely it is caused by an error
from bdrv_flush(), but we're not logging the errno anywhere, hence
this new probe.
Reviewed-by: Connor Kuehl <ckuehl@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
We can detect disk migration in migrate_prepare, if disk migration
is enabled in COLO mode, we can directly report an error.and there
is no need to disable block migration at every checkpoint.
Signed-off-by: Lei Rao <lei.rao@intel.com>
Signed-off-by: Zhang Chen <chen.zhang@intel.com>
Reviewed-by: Li Zhijian <lizhijian@fujitsu.com>
Reviewed-by: Zhang Chen <chen.zhang@intel.com>
Reviewed-by: Lukas Straub <lukasstraub2@web.de>
Tested-by: Lukas Straub <lukasstraub2@web.de>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Add a cleanup hook for incoming migration that gets called
at the end as a way for a transport to allow cleanup.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Message-Id: <20210421112834.107651-4-dgilbert@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
The CONFIG_VFIO switch only works in target specific code. Since
migration/migration.c is common code, the #ifdef does not have
the intended behavior here. Move the related code to a separate
file now which gets compiled via specific_ss instead.
Fixes: 3710586caa ("qapi: Add VFIO devices migration stats in Migration stats")
Message-Id: <20210414112004.943383-3-thuth@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Resizing while migrating is dangerous and does not work as expected.
The whole migration code works on the usable_length of ram blocks and does
not expect this to change at random points in time.
In the case of precopy, the ram block size must not change on the source,
after syncing the RAM block list in ram_save_setup(), so as long as the
guest is still running on the source.
Resizing can be trigger *after* (but not during) a reset in
ACPI code by the guest
- hw/arm/virt-acpi-build.c:acpi_ram_update()
- hw/i386/acpi-build.c:acpi_ram_update()
Use the ram block notifier to get notified about resizes. Let's simply
cancel migration and indicate the reason. We'll continue running on the
source. No harm done.
Update the documentation. Postcopy will be handled separately.
Reviewed-by: Peter Xu <peterx@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20210429112708.12291-5-david@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Manual merge
Result @blocked is redundant. Unfortunately, we realized this too
close to the release to risk dropping it, so we deprecated it
instead, in commit e11ce6c06.
Since it was deprecated from the start, we can delete it without
the customary grace period. Do so.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Message-Id: <20210429140424.2802929-1-armbru@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
This commit solves the issue with userfault_fd WP feature that
background snapshot is based on. For any never poluated or discarded
memory page, the UFFDIO_WRITEPROTECT ioctl() would skip updating
PTE for that page, thereby loosing WP setting for it.
So we need to pre-fault pages for each RAM block to be protected
before making a userfault_fd wr-protect ioctl().
Fixes: 278e2f551a (migration: support
UFFD write fault processing in ram_save_iterate())
Signed-off-by: Andrey Gruzdev <andrey.gruzdev@virtuozzo.com>
Reported-by: David Hildenbrand <david@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Message-Id: <20210401092226.102804-4-andrey.gruzdev@virtuozzo.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
dgilbert:
Bodged ifdef __linux__ on ram_write_tracking_prepare, should really
go in a stub
The same thing as for incoming postcopy - we cannot deal with concurrent
RAM discards when using background snapshot feature in outgoing migration.
Fixes: 8518278a6a (migration: implementation
of background snapshot thread)
Signed-off-by: Andrey Gruzdev <andrey.gruzdev@virtuozzo.com>
Reported-by: David Hildenbrand <david@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Message-Id: <20210401092226.102804-3-andrey.gruzdev@virtuozzo.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Added missing qemu_fflush() on buffer file holding precopy device state.
Increased initial QIOChannelBuffer allocation to 512KB to avoid reallocs.
Typical configurations often require >200KB for device state and VMDESC.
Fixes: 8518278a6a (migration: implementation
of background snapshot thread)
Signed-off-by: Andrey Gruzdev <andrey.gruzdev@virtuozzo.com>
Message-Id: <20210401092226.102804-2-andrey.gruzdev@virtuozzo.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
The generic 'migrate_set_parameters' command handle all types of param.
Only the QMP commands were documented in the deprecations page, but the
rationale for deprecating applies equally to HMP, and the replacements
exist. Furthermore the HMP commands are just shims to the QMP commands,
so removing the latter breaks the former unless they get re-implemented.
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Replaced various qemu_mutex_lock calls and their respective
qemu_mutex_unlock calls with QEMU_LOCK_GUARD macro. This simplifies
the code by eliminating the respective qemu_mutex_unlock calls.
Signed-off-by: Mahmoud Mandour <ma.mandourr@gmail.com>
Message-Id: <20210311031538.5325-7-ma.mandourr@gmail.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Modify query-migrate so that it has a flag indicating if outbound
migration is blocked, and if it is a list of reasons.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20210202135522.127380-2-dgilbert@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
migrate_params_check() has a number of error messages of the form
Parameter 'NAME' expects is invalid, it should be ...
Fix them to something like
Parameter 'NAME' expects a ...
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20210202141734.2488076-5-armbru@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
73af8dd8d7 "migration: Make xbzrle_cache_size a migration
parameter" (v2.11.0) made the new parameter unsigned (QAPI type
'size', uint64_t in C). It neglected to update existing code, which
continues to use int64_t.
migrate_xbzrle_cache_size() returns the new parameter. Adjust its
return type.
QMP query-migrate-cache-size returns migrate_xbzrle_cache_size().
Adjust its return type.
migrate-set-parameters passes the new parameter to
xbzrle_cache_resize(). Adjust its parameter type.
xbzrle_cache_resize() passes it on to cache_init(). Adjust its
parameter type.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20210202141734.2488076-3-armbru@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Introducing implementation of 'background' snapshot thread
which in overall follows the logic of precopy migration
while internally utilizes completely different mechanism
to 'freeze' vmstate at the start of snapshot creation.
This mechanism is based on userfault_fd with wr-protection
support and is Linux-specific.
Signed-off-by: Andrey Gruzdev <andrey.gruzdev@virtuozzo.com>
Acked-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20210129101407.103458-5-andrey.gruzdev@virtuozzo.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Add new capability to 'qapi/migration.json' schema.
Update migrate_caps_check() to validate enabled capability set
against introduced one. Perform checks for required kernel features
and compatibility with guest memory backends.
Signed-off-by: Andrey Gruzdev <andrey.gruzdev@virtuozzo.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Acked-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20210129101407.103458-2-andrey.gruzdev@virtuozzo.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
These cases require a bit more thought to review; in each case, the
code was appending to a list, but not with a FOOList **tail variable.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-Id: <20210113221013.390592-6-eblake@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
[Flawed change to qmp_guest_network_get_interfaces() dropped]
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Register yank functions on sockets to shut them down.
Signed-off-by: Lukas Straub <lukasstraub2@web.de>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
Acked-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <484c6a14cc2506bebedd5a237259b91363ff8f88.1609167865.git.lukasstraub2@web.de>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
-----BEGIN PGP SIGNATURE-----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=vGLy
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/armbru/tags/pull-qapi-2020-12-19' into staging
QAPI patches patches for 2020-12-19
# gpg: Signature made Sat 19 Dec 2020 09:40:05 GMT
# gpg: using RSA key 354BC8B3D7EB2A6B68674E5F3870B400EB918653
# gpg: issuer "armbru@redhat.com"
# gpg: Good signature from "Markus Armbruster <armbru@redhat.com>" [full]
# gpg: aka "Markus Armbruster <armbru@pond.sub.org>" [full]
# Primary key fingerprint: 354B C8B3 D7EB 2A6B 6867 4E5F 3870 B400 EB91 8653
* remotes/armbru/tags/pull-qapi-2020-12-19: (33 commits)
qobject: Make QString immutable
block: Use GString instead of QString to build filenames
keyval: Use GString to accumulate value strings
json: Use GString instead of QString to accumulate strings
migration: Replace migration's JSON writer by the general one
qobject: Factor JSON writer out of qobject_to_json()
qobject: Factor quoted_str() out of to_json()
qobject: Drop qstring_get_try_str()
qobject: Drop qobject_get_try_str()
Revert "qobject: let object_property_get_str() use new API"
block: Avoid qobject_get_try_str()
qmp: Fix tracing of non-string command IDs
qobject: Move internals to qobject-internal.h
hw/rdma: Replace QList by GQueue
Revert "qstring: add qstring_free()"
qobject: Change qobject_to_json()'s value to GString
qobject: Use GString instead of QString to accumulate JSON
qobject: Make qobject_to_json_pretty() take a pretty argument
monitor: Use GString instead of QString for output buffer
hmp: Simplify how qmp_human_monitor_command() gets output
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Anywhere we create a list of just one item or by prepending items
(typically because order doesn't matter), we can use
QAPI_LIST_PREPEND(). But places where we must keep the list in order
by appending remain open-coded until later patches.
Note that as a side effect, this also performs a cleanup of two minor
issues in qga/commands-posix.c: the old code was performing
new = g_malloc0(sizeof(*ret));
which 1) is confusing because you have to verify whether 'new' and
'ret' are variables with the same type, and 2) would conflict with C++
compilation (not an actual problem for this file, but makes
copy-and-paste harder).
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <20201113011340.463563-5-eblake@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
[Straightforward conflicts due to commit a8aa94b5f8 "qga: update
schema for guest-get-disks 'dependents' field" and commit a10b453a52
"target/mips: Move mips_cpu_add_definition() from helper.c to cpu.c"
resolved. Commit message tweaked.]
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Instead of taking a list parameter and returning a new head at a
distance, just return the new item for the caller to insert into a
list via QAPI_LIST_PREPEND.
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <20201113011340.463563-4-eblake@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Move the property types and property macros implemented in
qdev-properties-system.c to a new qdev-properties-system.h
header.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20201211220529.2290218-16-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
The following steps will cause qemu assertion failure:
- pause vm by executing 'virsh suspend'
- create external snapshot of memory and disk using 'virsh snapshot-create-as'
- doing the above operation again will cause qemu crash
The backtrace looks like:
at /build/qemu-5.0/migration/savevm.c:1401
at /build/qemu-5.0/migration/savevm.c:1453
When the first migration completes, bs->open_flags will set BDRV_O_INACTIVE
flag by bdrv_inactivate_all(), and during the second migration the
bdrv_inactivate_recurse assert that the bs->open_flags is already
BDRV_O_INACTIVE enabled which cause crash.
As Vladimir suggested, this patch makes migrate_prepare check the state of vm and
return error if it is in RUN_STATE_POSTMIGRATE state.
Signed-off-by: Tuguoyi <tu.guoyi@h3c.com>
Message-Id: <6b704294ad2e405781c38fb38d68c744@h3c.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reported-by: Li Zhang <li.zhang@cloud.ionos.com>
Reviewed-by: Pankaj Gupta <pankaj.gupta@cloud.ionos.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Make qemu_start_incoming_migration local to migration/migration.c.
By using the runstate instead of a separate flag, vl need not do
anything to setup deferred incoming migration.
qmp_migrate_incoming also does not need the deferred_incoming flag
anymore, because "-incoming PROTOCOL" will clear the "once" flag
before the main loop starts. Therefore, later invocations of
the migrate-incoming command will fail with the existing
"The incoming migration has already been started" error message.
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Some very simple initialization routines can be nested in existing
subsystem-level functions, do that to simplify qemu_init.
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The following sequence may cause the VM abort during migration:
1. RUN_STATE_RUNNING,MIGRATION_STATUS_ACTIVE
2. before call migration_completion(), we send migrate_cancel
QMP command, the state machine is changed to:
RUN_STATE_RUNNING,MIGRATION_STATUS_CANCELLING
3. call migration_completion(), and the state machine is
switch to: RUN_STATE_RUNNING,MIGRATION_STATUS_COMPLETED
4. call migration_iteration_finish(), because the migration
status is COMPLETED, so it will try to set the runstate
to POSTMIGRATE, but RUNNING-->POSTMIGRATE is an invalid
transition, so abort().
The migration_completion() should not change the migration state
to COMPLETED if it is already changed to CANCELLING.
Signed-off-by: Longpeng(Mike) <longpeng2@huawei.com>
Message-Id: <20201105091726.148-1-longpeng2@huawei.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
After the WITH_QEMU_LOCK_GUARD macro is added, the compiler cannot identify
that the statements in the macro must be executed. As a result, some variables
assignment statements in the macro may be considered as unexecuted by the compiler.
When the -Wmaybe-uninitialized capability is enabled on GCC9,the compiler showed warning:
migration/migration.c: In function ‘migrate_send_rp_req_pages’:
migration/migration.c:384:8: warning: ‘received’ may be used uninitialized in this function [-Wmaybe-uninitialized]
384 | if (received) {
| ^
Add a default value for 'received' to prevented the warning.
Reported-by: Euler Robot <euler.robot@huawei.com>
Signed-off-by: Chen Qun <kuhn.chenqun@huawei.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20201111142203.2359370-6-kuhn.chenqun@huawei.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Added amount of bytes transferred to the VM at destination by all VFIO
devices
Signed-off-by: Kirti Wankhede <kwankhede@nvidia.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Another go at Peter's postcopy fixes
Cleanups from Bihong Yu and Peter Maydell.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
-----BEGIN PGP SIGNATURE-----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=OL0Q
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dgilbert/tags/pull-migration-20201026a' into staging
migration pull: 2020-10-26
Another go at Peter's postcopy fixes
Cleanups from Bihong Yu and Peter Maydell.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
# gpg: Signature made Mon 26 Oct 2020 16:17:03 GMT
# gpg: using RSA key 45F5C71B4A0CB7FB977A9FA90516331EBC5BFDE7
# gpg: Good signature from "Dr. David Alan Gilbert (RH2) <dgilbert@redhat.com>" [full]
# Primary key fingerprint: 45F5 C71B 4A0C B7FB 977A 9FA9 0516 331E BC5B FDE7
* remotes/dgilbert/tags/pull-migration-20201026a:
migration-test: Only hide error if !QTEST_LOG
migration/postcopy: Release fd before going into 'postcopy-pause'
migration: Sync requested pages after postcopy recovery
migration: Maintain postcopy faulted addresses
migration: Introduce migrate_send_rp_message_req_pages()
migration: Pass incoming state into qemu_ufd_copy_ioctl()
migration: using trace_ to replace DPRINTF
migration: Delete redundant spaces
migration: Open brace '{' following function declarations go on the next line
migration: Do not initialise statics and globals to 0 or NULL
migration: Add braces {} for if statement
migration: Open brace '{' following struct go on the same line
migration: Add spaces around operator
migration: Don't use '#' flag of printf format
migration: Do not use C99 // comments
migration: Drop unused VMSTATE_FLOAT64 support
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Logically below race could trigger with the old code:
test program migration thread
------------ ----------------
wait_until('postcopy-pause')
postcopy_pause()
set_state('postcopy-pause')
do_postcopy_recover()
arm s->to_dst_file with new fd
release s->to_dst_file [1]
Here [1] could have released the just-installed recoverying channel. Then the
migration could hang without really resuming.
Instead, it should be very safe to release the fd before setting the state into
'postcopy-pause', because there's no reason for any other thread to touch it
during 'postcopy-active'.
Dave reported a very rare postcopy recovery hang that the migration-test
program waited for the migration to complete in migrate_postcopy_complete().
We do suspect it's the same thing that we're gonna fix here. Hard to tell.
However since we've noticed this, fix this irrelevant of the hang report.
Cc: Dr. David Alan Gilbert <dgilbert@redhat.com>
Cc: Juan Quintela <quintela@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20201021212721.440373-6-peterx@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Maintain a list of faulted addresses on the destination host for which we're
waiting on. This is implemented using a GTree rather than a real list to make
sure even there're plenty of vCPUs/threads that are faulting, the lookup will
still be fast with O(log(N)) (because we'll do that after placing each page).
It should bring a slight overhead, but ideally that shouldn't be a big problem
simply because in most cases the requested page list will be short.
Actually we did similar things for postcopy blocktime measurements. This patch
didn't use that simply because:
(1) blocktime measurement is towards vcpu threads only, but here we need to
record all faulted addresses, including main thread and external
thread (like, DPDK via vhost-user).
(2) blocktime measurement will require UFFD_FEATURE_THREAD_ID, but here we
don't want to add that extra dependency on the kernel version since not
necessary. E.g., we don't need to know which thread faulted on which
page, we also don't care about multiple threads faulting on the same
page. But we only care about what addresses are faulted so waiting for a
page copying from src.
(3) blocktime measurement is not enabled by default. However we need this by
default especially for postcopy recover.
Another thing to mention is that this patch introduced a new mutex to serialize
the receivedmap and the page_requested tree, however that serialization does
not cover other procedures like UFFDIO_COPY.
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20201021212721.440373-4-peterx@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
This is another layer wrapper for sending a page request to the source VM. The
new migrate_send_rp_message_req_pages() will be used elsewhere in coming
patches.
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20201021212721.440373-3-peterx@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Bihong Yu <yubihong@huawei.com>
Reviewed-by: Chuan Zheng <zhengchuan@huawei.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <1603163448-27122-4-git-send-email-yubihong@huawei.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
hostname is need in multifd-tls, save hostname into MigrationState.
Signed-off-by: Chuan Zheng <zhengchuan@huawei.com>
Signed-off-by: Yan Jin <jinyan12@huawei.com>
Message-Id: <1600139042-104593-2-git-send-email-zhengchuan@huawei.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
max-bandwidth is set by default to 32 MiB/s (256 Mib/s)
since 2008 (5bb7910af0).
Most of the CPUs can dirty memory faster than that now,
and this is clearly a problem with POWER where the page
size is 64 kiB and not 4 KiB.
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Message-Id: <20200921144957.979989-1-lvivier@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
We duplicated the logic of maintaining the last_rb variable at both callers of
this function. Pass *rb pointer into the function so that we can avoid
duplicating the logic. Also, when we have the rb pointer, it's also easier to
remove the original 2nd & 4th parameters, because both of them (name of the
ramblock when needed, or the page size) can be fetched from the ramblock
pointer too.
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20200908203022.341615-3-peterx@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
In migration_incoming_state_destroy(), we've got a few variables that aren't
destroyed properly, namely:
main_thread_load_event
postcopy_pause_sem_dst
postcopy_pause_sem_fault
rp_mutex
Destroy them properly.
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20200908203022.341615-2-peterx@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
clang's C11 atomic_fetch_*() functions only take a C11 atomic type
pointer argument. QEMU uses direct types (int, etc) and this causes a
compiler error when a QEMU code calls these functions in a source file
that also included <stdatomic.h> via a system header file:
$ CC=clang CXX=clang++ ./configure ... && make
../util/async.c:79:17: error: address argument to atomic operation must be a pointer to _Atomic type ('unsigned int *' invalid)
Avoid using atomic_*() names in QEMU's atomic.h since that namespace is
used by <stdatomic.h>. Prefix QEMU's APIs with 'q' so that atomic.h
and <stdatomic.h> can co-exist. I checked /usr/include on my machine and
searched GitHub for existing "qatomic_" users but there seem to be none.
This patch was generated using:
$ git grep -h -o '\<atomic\(64\)\?_[a-z0-9_]\+' include/qemu/atomic.h | \
sort -u >/tmp/changed_identifiers
$ for identifier in $(</tmp/changed_identifiers); do
sed -i "s%\<$identifier\>%q$identifier%g" \
$(git grep -I -l "\<$identifier\>")
done
I manually fixed line-wrap issues and misaligned rST tables.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20200923105646.47864-1-stefanha@redhat.com>
The vsock channel is more widely use in some new features, for example,
the Nitro/Enclave. It can also be used as the migration channel.
Signed-off-by: Longpeng(Mike) <longpeng2@huawei.com>
Message-Id: <20200806074030.174-3-longpeng2@huawei.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Currently, the only difference of tcp channel and unix channel in
migration/socket.c is the way to build SocketAddress, but socket_parse()
can handle these two types, so use it to instead of tcp_build_address()
and unix_build_address().
The socket-type channel can be further unified based on the up, this
would be helpful for us to add other socket-type channels.
Signed-off-by: Longpeng(Mike) <longpeng2@huawei.com>
Message-Id: <20200806074030.174-2-longpeng2@huawei.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
This migration parameter allows mapping block node names and bitmap
names to aliases for the purpose of block dirty bitmap migration.
This way, management tools can use different node and bitmap names on
the source and destination and pass the mapping of how bitmaps are to be
transferred to qemu (on the source, the destination, or even both with
arbitrary aliases in the migration stream).
While touching this code, fix a bug where bitmap names longer than 255
bytes would fail an assertion in qemu_put_counted_string().
Suggested-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
Message-Id: <20200820150725.68687-2-mreitz@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Signed-off-by: Eric Blake <eblake@redhat.com>
If target is turned off prior to postcopy finished, target crashes
because busy bitmaps are found at shutdown.
Canceling incoming migration helps, as it removes all unfinished (and
therefore busy) bitmaps.
Similarly on source we crash in bdrv_close_all which asserts that all
bdrv states are removed, because bdrv states involved into dirty bitmap
migration are referenced by it. So, we need to cancel outgoing
migration as well.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Andrey Shinkevich <andrey.shinkevich@virtuozzo.com>
Message-Id: <20200727194236.19551-17-vsementsov@virtuozzo.com>
Signed-off-by: Eric Blake <eblake@redhat.com>
No reasons to keep two public init functions.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Andrey Shinkevich <andrey.shinkevich@virtuozzo.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20200727194236.19551-11-vsementsov@virtuozzo.com>
Signed-off-by: Eric Blake <eblake@redhat.com>
Remove superfluous breaks, as there is a "return" before them.
Signed-off-by: Liao Pingfang <liao.pingfang@zte.com.cn>
Signed-off-by: Yi Wang <wang.yi59@zte.com.cn>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
"tmp.tls_hostname" and "tmp.tls_creds" allocated by migrate_params_test_apply()
is forgot to free at the end of qmp_migrate_set_parameters(). Fix that.
The leak stack:
Direct leak of 2 byte(s) in 2 object(s) allocated from:
#0 0xffffb597c20b in __interceptor_malloc (/usr/lib64/libasan.so.4+0xd320b)
#1 0xffffb52dcb1b in g_malloc (/usr/lib64/libglib-2.0.so.0+0x58b1b)
#2 0xffffb52f8143 in g_strdup (/usr/lib64/libglib-2.0.so.0+0x74143)
#3 0xaaaac52447fb in migrate_params_test_apply (/usr/src/debug/qemu-4.1.0/migration/migration.c:1377)
#4 0xaaaac52fdca7 in qmp_migrate_set_parameters (/usr/src/debug/qemu-4.1.0/qapi/qapi-commands-migration.c:192)
#5 0xaaaac551d543 in qmp_dispatch (/usr/src/debug/qemu-4.1.0/qapi/qmp-dispatch.c:165)
#6 0xaaaac52a0a8f in qmp_dispatch (/usr/src/debug/qemu-4.1.0/monitor/qmp.c:125)
#7 0xaaaac52a1c7f in monitor_qmp_dispatch (/usr/src/debug/qemu-4.1.0/monitor/qmp.c:214)
#8 0xaaaac55cb0cf in aio_bh_call (/usr/src/debug/qemu-4.1.0/util/async.c:117)
#9 0xaaaac55d4543 in aio_bh_poll (/usr/src/debug/qemu-4.1.0/util/aio-posix.c:459)
#10 0xaaaac55cae0f in aio_dispatch (/usr/src/debug/qemu-4.1.0/util/async.c:268)
#11 0xffffb52d6a7b in g_main_context_dispatch (/usr/lib64/libglib-2.0.so.0+0x52a7b)
#12 0xaaaac55d1e3b(/usr/bin/qemu-kvm-4.1.0+0x1622e3b)
#13 0xaaaac4e314bb(/usr/bin/qemu-kvm-4.1.0+0xe824bb)
#14 0xaaaac47f45ef(/usr/bin/qemu-kvm-4.1.0+0x8455ef)
#15 0xffffb4bfef3f in __libc_start_main (/usr/lib64/libc.so.6+0x23f3f)
#16 0xaaaac47ffacb(/usr/bin/qemu-kvm-4.1.0+0x850acb)
Direct leak of 2 byte(s) in 2 object(s) allocated from:
#0 0xffffb597c20b in __interceptor_malloc (/usr/lib64/libasan.so.4+0xd320b)
#1 0xffffb52dcb1b in g_malloc (/usr/lib64/libglib-2.0.so.0+0x58b1b)
#2 0xffffb52f8143 in g_strdup (/usr/lib64/libglib-2.0.so.0+0x74143)
#3 0xaaaac5244893 in migrate_params_test_apply (/usr/src/debug/qemu-4.1.0/migration/migration.c:1382)
#4 0xaaaac52fdca7 in qmp_migrate_set_parameters (/usr/src/debug/qemu-4.1.0/qapi/qapi-commands-migration.c:192)
#5 0xaaaac551d543 in qmp_dispatch (/usr/src/debug/qemu-4.1.0/qapi/qmp-dispatch.c)
#6 0xaaaac52a0a8f in qmp_dispatch (/usr/src/debug/qemu-4.1.0/monitor/qmp.c:125)
#7 0xaaaac52a1c7f in monitor_qmp_dispatch (/usr/src/debug/qemu-4.1.0/monitor/qmp.c:214)
#8 0xaaaac55cb0cf in aio_bh_call (/usr/src/debug/qemu-4.1.0/util/async.c:117)
#9 0xaaaac55d4543 in aio_bh_poll (/usr/src/debug/qemu-4.1.0/util/aio-posix.c:459)
#10 0xaaaac55cae0f in in aio_dispatch (/usr/src/debug/qemu-4.1.0/util/async.c:268)
#11 0xffffb52d6a7b in g_main_context_dispatch (/usr/lib64/libglib-2.0.so.0+0x52a7b)
#12 0xaaaac55d1e3b(/usr/bin/qemu-kvm-4.1.0+0x1622e3b)
#13 0xaaaac4e314bb(/usr/bin/qemu-kvm-4.1.0+0xe824bb)
#14 0xaaaac47f45ef (/usr/bin/qemu-kvm-4.1.0+0x8455ef)
#15 0xffffb4bfef3f in __libc_start_main (/usr/lib64/libc.so.6+0x23f3f)
#16 0xaaaac47ffacb(/usr/bin/qemu-kvm-4.1.0+0x850acb)
Signed-off-by: Chuan Zheng <zhengchuan@huawei.com>
Reviewed-by: KeQian Zhu <zhukeqian1@huawei.com>
Reviewed-by: HaiLiang <zhang.zhanghailiang@huawei.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
move the vcpu throttling functionality into its own module.
This functionality is not specific to any accelerator,
and it is used currently by migration to slow down guests to try to
have migrations converge, and by the cocoa MacOS UI to throttle speed.
cpu-throttle contains the controls to adjust and inspect throttle
settings, start (set) and stop vcpu throttling, and the throttling
function itself that is run periodically on vcpus to make them take a nap.
Execution of the throttling function on all vcpus is triggered by a timer,
registered at module initialization.
No functionality change.
Signed-off-by: Claudio Fontana <cfontana@suse.de>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
Message-Id: <20200629093504.3228-3-cfontana@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
COLO will copy all memory in a RAM block, disable discarding of RAM.
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Tested-by: Lukas Straub <lukasstraub2@web.de>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Hailiang Zhang <zhang.zhanghailiang@huawei.com>
Cc: Juan Quintela <quintela@redhat.com>
Cc: "Dr. David Alan Gilbert" <dgilbert@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20200626072248.78761-10-david@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The only remaining special case is postcopy. It cannot handle
concurrent discards yet, which would result in requesting already sent
pages from the source. Special-case it in virtio-balloon instead.
Introduce migration_in_incoming_postcopy(), to find out if incoming
postcopy is active.
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Juan Quintela <quintela@redhat.com>
Cc: "Dr. David Alan Gilbert" <dgilbert@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20200626072248.78761-7-david@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20200610053247.1583243-31-armbru@redhat.com>
migration_rate_limit will erroneously ratelimit a shutdown socket,
which causes the migration thread to hang in ram_save_host_page
if the socket is shutdown.
Fix this by explicitly testing if the socket has errors or was
shutdown in migration_rate_limit.
Signed-off-by: Lukas Straub <lukasstraub2@web.de>
Message-Id: <e79085bbe2d46dfa007dd41820194d5e2d4fcd80.1590007004.git.lukasstraub2@web.de>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Users may need to check the xbzrle encoding rate to know if the guest
memory is xbzrle encoding-friendly, and dynamically turn off the
encoding if the encoding rate is low.
Signed-off-by: Yi Sun <yi.y.sun@intel.com>
Signed-off-by: Wei Wang <wei.w.wang@intel.com>
Message-Id: <1588208375-19556-1-git-send-email-wei.w.wang@intel.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
At the tail stage of throttling, the Guest is very sensitive to
CPU percentage while the @cpu-throttle-increment is excessive
usually at tail stage.
If this parameter is true, we will compute the ideal CPU percentage
used by the Guest, which may exactly make the dirty rate match the
dirty rate threshold. Then we will choose a smaller throttle increment
between the one specified by @cpu-throttle-increment and the one
generated by ideal CPU percentage.
Therefore, it is compatible to traditional throttling, meanwhile
the throttle increment won't be excessive at tail stage. This may
make migration time longer, and is disabled by default.
Signed-off-by: Keqian Zhu <zhukeqian1@huawei.com>
Message-Id: <20200413101508.54793-1-zhukeqian1@huawei.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Mao Zhongyi <maozhongyi@cmss.chinamobile.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <474bb6cf67defb8be9de5035c11aee57a680557a.1585641083.git.maozhongyi@cmss.chinamobile.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
use QERR_INVALID_PARAMETER_VALUE instead of
"Parameter '%s' expects" for consistency.
Signed-off-by: Mao Zhongyi <maozhongyi@cmss.chinamobile.com>
Message-Id: <4ce71da4a5f98ad6ead0806ec71043473dcb4c07.1585641083.git.maozhongyi@cmss.chinamobile.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
bad indentation conflicts with CODING_STYLE doc.
Signed-off-by: Mao Zhongyi <maozhongyi@cmss.chinamobile.com>
Message-Id: <09f7529c665cac0c6a5e032ac6fdb6ca701f7e37.1585329482.git.maozhongyi@cmss.chinamobile.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
- ran regexp "qemu_mutex_lock\(.*\).*\n.*if" to find targets
- replaced result with QEMU_LOCK_GUARD if all unlocks at function end
- replaced result with WITH_QEMU_LOCK_GUARD if unlock not at end
Signed-off-by: Daniel Brodsky <dnbrdsky@gmail.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-id: 20200404042108.389635-3-dnbrdsky@gmail.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
run:
(qemu) info migrate_parameters
announce-initial: 50 ms
...
announce-max: 550 ms
multifd-compression: none
xbzrle-cache-size: 4194304
max-postcopy-bandwidth: 0
tls-authz: '(null)'
Migration parameter 'tls-authz' is used to provide the QOM ID
of a QAuthZ subclass instance that provides the access control
check, default is NULL. But the empty string is not a valid
object ID, so use "" instead of the default. Although it will
fail when lookup an object with ID "", it is harmless, just
consistent with tls_creds.
As a bonus, this patch also fixed the bad indentation on the
last line and removed 'has_tls_authz' redundant check in
'hmp_info_migrate_parameters'.
Signed-off-by: Mao Zhongyi <maozhongyi@cmss.chinamobile.com>
Message-Id: <119f539a9f4d198bc3bcced46b8280520d60bc51.1585100802.git.maozhongyi@cmss.chinamobile.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Add new parameter description, also:
1. Remove unsociable space.
2. Nit picking: s/two/2 in report
Signed-off-by: Mao Zhongyi <maozhongyi@cmss.chinamobile.com>
Message-Id: <20200320143216.423374-1-maozhongyi@cmss.chinamobile.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
We will migrate parts of dirty pages backgroud lively during the gap time
of two checkpoints, without this modification, it will not work
because ram_save_iterate() will check it before send RAM_SAVE_FLAG_EOS
at the end of it.
Signed-off-by: zhanghailiang <zhang.zhanghailiang@huawei.com>
Message-Id: <20200224065414.36524-7-zhang.zhanghailiang@huawei.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Currently, if the bytes_dirty_period is more than the 50% of
bytes_xfer_period, we start or increase throttling.
If we make this percentage higher, then we can tolerate higher
dirty rate during migration, which means less impact on guest.
The side effect of higher percentage is longer migration time.
We can make this parameter configurable to switch between mig-
ration time first or guest performance first.
The default value is 50 and valid range is 1 to 100.
Signed-off-by: Keqian Zhu <zhukeqian1@huawei.com>
Message-Id: <20200224023142.39360-1-zhukeqian1@huawei.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
This helper has been called twice which is wrong.
Left the one where called while get COLO enable message
from source side.
Signed-off-by: zhanghailiang <zhang.zhanghailiang@huawei.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
This commit "migration: Create migration_is_running()" broke
COLO. Becuase there is a process broken by this commit.
colo_process_checkpoint
->colo_do_checkpoint_transaction
->migrate_set_block_enabled
->qmp_migrate_set_capabilities
It can be fixed by make COLO process as an exception,
Maybe we need a better way to fix it.
Cc: Juan Quintela <quintela@redhat.com>
Signed-off-by: zhanghailiang <zhang.zhanghailiang@huawei.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
This parameter specifies the zstd compression level. The next patch
will put it to use.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Acked-by: Markus Armbruster <armbru@redhat.com>
This parameter specifies the zlib compression level. The next patch
will put it to use.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Acked-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
It will be used later.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
---
No comp value needs to be zero.
This will store the compression method to use. We start with none.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Acked-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
---
Rename multifd-method to multifd-compression
qemu_savevm_nr_failover_devices() is originally designed to
get the number of failover devices, but it actually returns
the number of "unplug-pending" failover devices now. Moreover,
what drives migration state to wait-unplug should be the number
of "unplug-pending" failover devices, not all failover devices.
We can also notice that qemu_savevm_state_guest_unplug_pending()
and qemu_savevm_nr_failover_devices() is equivalent almost (from
the code view). So the latter is incorrect semantically and
useless, just delete it.
In the qemu_savevm_state_guest_unplug_pending(), once hit a
unplug-pending failover device, then it can return true right
now to save cpu time.
Signed-off-by: Keqian Zhu <zhukeqian1@huawei.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Tested-by: Jens Freimann <jfreimann@redhat.com>
Reviewed-by: Jens Freimann <jfreimann@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
If the migration is cancelled when it is in the completion phase,
the migration state is set to MIGRATION_STATUS_CANCELLING.
The VM maybe wait for the 'pause_sem' semaphore in migration_maybe_pause
function, so that VM always is paused.
Reported-by: Euler Robot <euler.robot@huawei.com>
Signed-off-by: Zhimin Feng <fengzhimin1@huawei.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
We need to change the full chain to pass the Error parameter.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
This function returns true if we are in the middle of a migration.
It is like migration_is_setup_or_active() with CANCELLING and COLO.
Adapt all callers that are needed.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
postcopy requires to place a whole host page, while migration thread
migrate memory in target page size. This makes postcopy need to collect
all target pages in one host page before placing via userfaultfd.
To enable compress during postcopy, there are two problems to solve:
1. Random order for target page arrival
2. Target pages in one host page arrives without interrupt by target
page from other host page
The first one is handled by previous cleanup patch.
This patch handles the second one by:
1. Flush compress thread for each host page
2. Wait for decompress thread for before placing host page
Signed-off-by: Wei Yang <richardw.yang@linux.intel.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
The current check sets an error but doesn't fail the command.
This may cause a problem if new connection attempt by the same URI
affects the first connection.
Signed-off-by: Yury Kotov <yury-kotov@yandex-team.ru>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Darren Kenny <darren.kenny@oracle.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Clang does not like qmp_migrate_set_downtime()'s code to clamp double
@value to 0..INT64_MAX:
qemu/migration/migration.c:2038:24: error: implicit conversion from 'long' to 'double' changes value from 9223372036854775807 to 9223372036854775808 [-Werror,-Wimplicit-int-float-conversion]
The warning will be enabled by default in clang 10. It is not
available for clang <= 9.
The clamp is actually useless; @value is checked to be within
0..MAX_MIGRATE_DOWNTIME_SECONDS immediately before. Delete it.
While there, make the conversion from double to int64_t explicit.
Signed-off-by: Fangrui Song <i@maskray.me>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
[Patch split, commit message improved]
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
When using hugepages, rate limiting is necessary within each huge
page, since a 1G huge page can take a significant time to send, so
you end up with bursty behaviour.
Fixes: 4c011c37ec ("postcopy: Send whole huge pages")
Reported-by: Lin Ma <LMa@suse.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
This patch adds a new migration state called wait-unplug. It is entered
after the SETUP state if failover devices are present. It will transition
into ACTIVE once all devices were succesfully unplugged from the guest.
So if a guest doesn't respond or takes long to honor the unplug request
the user will see the migration state 'wait-unplug'.
In the migration thread we query failover devices if they're are still
pending the guest unplug. When all are unplugged the migration
continues. If one device won't unplug migration will stay in wait_unplug
state.
Signed-off-by: Jens Freimann <jfreimann@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20191029114905.6856-9-jfreimann@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
There are three page size in qemu:
real host page size
host page size
target page size
All of them have dedicate variable to represent. For the last two, we
use the same form in the whole qemu project, while for the first one we
use two forms: qemu_real_host_page_size and getpagesize().
qemu_real_host_page_size is defined to be a replacement of
getpagesize(), so let it serve the role.
[Note] Not fully tested for some arch or device.
Signed-off-by: Wei Yang <richardw.yang@linux.intel.com>
Message-Id: <20191013021145.16011-3-richardw.yang@linux.intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Not necessary to do the check again.
Signed-off-by: Wei Yang <richardw.yang@linux.intel.com>
Message-Id: <20191005220517.24029-4-richardw.yang@linux.intel.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
In normal precopy we can't do reconnection recovery - but we also
don't need to, since you can just rerun migration.
At the moment if the 'return-path' capability is on, we use
the return path in precopy to give a positive 'OK' to the end
of migration; however if migration fails then we fall into
the postcopy recovery path and hang. This fixes it by only
running the return path in the postcopy case.
Reported-by: Greg Kurz <groug@kaod.org>
Tested-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Wrap the check into a function to make it easy to read.
Signed-off-by: Wei Yang <richardw.yang@linux.intel.com>
Message-Id: <20190717005341.14140-1-richardw.yang@linux.intel.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Various parts of the migration code do different things when they're
in postcopy mode; prior to this patch this has been 'postcopy-active'.
This patch extends 'in_postcopy' to include 'postcopy-paused' and
'postcopy-recover'.
In particular, when you set the max-postcopy-bandwidth parameter, this
only affects the current migration fd if we're 'in_postcopy';
this leads to a race in the postcopy recovery test where it increases
the speed from 4k/sec to unlimited, but that increase can get ignored
if the change is made between the point at which the reconnection
happens and it transitions back to active.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20190923174942.12182-1-dgilbert@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Tested-by: Alex Bennée <alex.bennee@linaro.org>
Tested-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Wei Yang <richardw.yang@linux.intel.com>
Message-Id: <20190912024957.11780-1-richardw.yang@linux.intel.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
We've got max-postcopy-bandwidth parameter but it's not applied
correctly after a postcopy recovery so the recovered migration stream
will still eat the whole net bandwidth. Fix that up.
Reported-by: Xiaohui Li <xiaohli@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20190906130103.20961-1-peterx@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
This capability realizes simple source validation by UUID.
It's useful for live migration between hosts.
Signed-off-by: Yury Kotov <yury-kotov@yandex-team.ru>
Message-Id: <20190903162246.18524-2-yury-kotov@yandex-team.ru>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
-----BEGIN PGP SIGNATURE-----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=eSUz
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/armbru/tags/pull-include-2019-08-13-v2' into staging
Header cleanup patches for 2019-08-13
# gpg: Signature made Fri 16 Aug 2019 12:39:12 BST
# gpg: using RSA key 354BC8B3D7EB2A6B68674E5F3870B400EB918653
# gpg: issuer "armbru@redhat.com"
# gpg: Good signature from "Markus Armbruster <armbru@redhat.com>" [full]
# gpg: aka "Markus Armbruster <armbru@pond.sub.org>" [full]
# Primary key fingerprint: 354B C8B3 D7EB 2A6B 6867 4E5F 3870 B400 EB91 8653
* remotes/armbru/tags/pull-include-2019-08-13-v2: (29 commits)
sysemu: Split sysemu/runstate.h off sysemu/sysemu.h
sysemu: Move the VMChangeStateEntry typedef to qemu/typedefs.h
Include sysemu/sysemu.h a lot less
Clean up inclusion of sysemu/sysemu.h
numa: Move remaining NUMA declarations from sysemu.h to numa.h
Include sysemu/hostmem.h less
numa: Don't include hw/boards.h into sysemu/numa.h
Include hw/boards.h a bit less
Include hw/qdev-properties.h less
Include qemu/main-loop.h less
Include qemu/queue.h slightly less
Include hw/hw.h exactly where needed
Include qom/object.h slightly less
Include exec/memory.h slightly less
Include migration/vmstate.h less
migration: Move the VMStateDescription typedef to typedefs.h
Clean up inclusion of exec/cpu-common.h
Include hw/irq.h a lot less
typedefs: Separate incomplete types and function types
ide: Include hw/ide/internal a bit less outside hw/ide/
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
sysemu/sysemu.h is a rather unfocused dumping ground for stuff related
to the system-emulator. Evidence:
* It's included widely: in my "build everything" tree, changing
sysemu/sysemu.h still triggers a recompile of some 1100 out of 6600
objects (not counting tests and objects that don't depend on
qemu/osdep.h, down from 5400 due to the previous two commits).
* It pulls in more than a dozen additional headers.
Split stuff related to run state management into its own header
sysemu/runstate.h.
Touching sysemu/sysemu.h now recompiles some 850 objects. qemu/uuid.h
also drops from 1100 to 850, and qapi/qapi-types-run-state.h from 4400
to 4200. Touching new sysemu/runstate.h recompiles some 500 objects.
Since I'm touching MAINTAINERS to add sysemu/runstate.h anyway, also
add qemu/main-loop.h.
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190812052359.30071-30-armbru@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
[Unbreak OS-X build]
In my "build everything" tree, changing sysemu/sysemu.h triggers a
recompile of some 5400 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).
hw/qdev-core.h includes sysemu/sysemu.h since recent commit e965ffa70a
"qdev: add qdev_add_vm_change_state_handler()". This is a bad idea:
hw/qdev-core.h is widely included.
Move the declaration of qdev_add_vm_change_state_handler() to
sysemu/sysemu.h, and drop the problematic include from hw/qdev-core.h.
Touching sysemu/sysemu.h now recompiles some 1800 objects.
qemu/uuid.h also drops from 5400 to 1800. A few more headers show
smaller improvement: qemu/notify.h drops from 5600 to 5200,
qemu/timer.h from 5600 to 4500, and qapi/qapi-types-run-state.h from
5500 to 5000.
Cc: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20190812052359.30071-28-armbru@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
In my "build everything" tree, changing hw/qdev-properties.h triggers
a recompile of some 2700 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).
Many places including hw/qdev-properties.h (directly or via hw/qdev.h)
actually need only hw/qdev-core.h. Include hw/qdev-core.h there
instead.
hw/qdev.h is actually pointless: all it does is include hw/qdev-core.h
and hw/qdev-properties.h, which in turn includes hw/qdev-core.h.
Replace the remaining uses of hw/qdev.h by hw/qdev-properties.h.
While there, delete a few superfluous inclusions of hw/qdev-core.h.
Touching hw/qdev-properties.h now recompiles some 1200 objects.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Daniel P. Berrangé" <berrange@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20190812052359.30071-22-armbru@redhat.com>
In my "build everything" tree, changing qemu/main-loop.h triggers a
recompile of some 5600 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h). It includes block/aio.h,
which in turn includes qemu/event_notifier.h, qemu/notify.h,
qemu/processor.h, qemu/qsp.h, qemu/queue.h, qemu/thread-posix.h,
qemu/thread.h, qemu/timer.h, and a few more.
Include qemu/main-loop.h only where it's needed. Touching it now
recompiles only some 1700 objects. For block/aio.h and
qemu/event_notifier.h, these numbers drop from 5600 to 2800. For the
others, they shrink only slightly.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190812052359.30071-21-armbru@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
This patch fix a multifd migration bug in migration speed calculation, this
problem can be reproduced as follows:
1. start a vm and give a heavy memory write stress to prevent the vm be
successfully migrated to destination
2. begin a migration with multifd
3. migrate for a long time [actually, this can be measured by transferred bytes]
4. migrate cancel
5. begin a new migration with multifd, the migration will directly run into
migration_completion phase
Reason as follows:
Migration update bandwidth and s->threshold_size in function
migration_update_counters after BUFFER_DELAY time:
current_bytes = migration_total_bytes(s);
transferred = current_bytes - s->iteration_initial_bytes;
time_spent = current_time - s->iteration_start_time;
bandwidth = (double)transferred / time_spent;
s->threshold_size = bandwidth * s->parameters.downtime_limit;
In multifd migration, migration_total_bytes function return
qemu_ftell(s->to_dst_file) + ram_counters.multifd_bytes.
s->iteration_initial_bytes will be initialized to 0 at every new migration,
but ram_counters is a global variable, and history migration data will be
accumulated. So if the ram_counters.multifd_bytes is big enough, it may lead
pending_size >= s->threshold_size become false in migration_iteration_run
after the first migration_update_counters.
Signed-off-by: Ivan Ren <ivanren@tencent.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Wei Yang <richardw.yang@linux.intel.com>
Suggested-by: Wei Yang <richardw.yang@linux.intel.com>
Message-Id: <1564741121-1840-1-git-send-email-ivanren@tencent.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
MigrationState->bytes_xfer is only set to 0 in migrate_init().
Remove this unnecessary field.
Signed-off-by: Wei Yang <richardw.yang@linux.intel.com>
Message-Id: <20190402003106.17614-1-richardw.yang@linux.intel.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
There is only one place to set start_postcopy to true,
qmp_migrate_start_postcopy(), which make sure start_postcopy could be
set to true when migrate_postcopy() return true.
So start_postcopy is true implies the other one.
Signed-off-by: Wei Yang <richardw.yang@linux.intel.com>
Message-Id: <20190718083747.5859-1-richardw.yang@linux.intel.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>