The MusicPal board code connects both of the IRQ outputs of the UART
to the same INTC qemu_irq. Connecting two qemu_irqs outputs directly
to the same input is not valid as it produces subtly wrong behaviour
(for instance if both the IRQ lines are high, and then one goes
low, the INTC input will see this as a high-to-low transition
even though the second IRQ line should still be holding it high).
This kind of wiring needs an explicitly created OR gate; add one.
Inspired-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20201107193403.436146-5-f4bug@amsat.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When using a Cortex-A15, the Virt machine does not use any
MPCore peripherals. Remove the dependency.
Fixes: 7951c7b7c0 ("hw/arm: Express dependencies of the virt machine with Kconfig")
Reported-by: Miroslav Rezanina <mrezanin@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20201107114852.271922-1-philmd@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
commit 32bd322a01 ("hw/timer/armv7m_systick: Rewrite to use ptimers")
changed armv7m_systick to build on ptimers. Make sure we have ptimers
in the build when building armv7m_systick.
Signed-off-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20201104103343.30392-1-drjones@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Generic watchdog device model implementation as per ARM SBSA v6.0
Signed-off-by: Shashi Mallela <shashi.mallela@linaro.org>
Message-id: 20201027015927.29495-2-shashi.mallela@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The recently added LED device reports LED status changes with
the 'led_set_intensity' trace event. It is less invasive than
the fprintf() calls. We need however to have a binary built
with tracing support.
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20200912134041.946260-8-f4bug@amsat.org>
The Witherspoon has 3 LEDs connected to a PCA9552. Add them.
The names and reset values are taken from:
https://github.com/open-power/witherspoon-xml/blob/master/witherspoon.xml
Example booting obmc-phosphor-image:
$ qemu-system-arm -M witherspoon-bmc -trace led_change_intensity
1592693373.997015:led_change_intensity LED desc:'front-fault-4' color:green intensity 0% -> 100%
1592693373.997632:led_change_intensity LED desc:'front-power-3' color:green intensity 0% -> 100%
1592693373.998239:led_change_intensity LED desc:'front-id-5' color:green intensity 0% -> 100%
1592693500.291805:led_change_intensity LED desc:'front-power-3' color:green intensity 100% -> 0%
1592693500.312041:led_change_intensity LED desc:'front-power-3' color:green intensity 0% -> 100%
1592693500.821254:led_change_intensity LED desc:'front-power-3' color:green intensity 100% -> 0%
1592693501.331517:led_change_intensity LED desc:'front-power-3' color:green intensity 0% -> 100%
1592693501.841367:led_change_intensity LED desc:'front-power-3' color:green intensity 100% -> 0%
1592693502.350839:led_change_intensity LED desc:'front-power-3' color:green intensity 0% -> 100%
1592693502.861134:led_change_intensity LED desc:'front-power-3' color:green intensity 100% -> 0%
1592693503.371090:led_change_intensity LED desc:'front-power-3' color:green intensity 0% -> 100%
We notice the front-power LED starts to blink at a ~2Hz rate.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20200912134041.946260-5-f4bug@amsat.org>
While APEI is a generic ACPI feature (usable by X86 and ARM64), only
the 'virt' machine uses it, by enabling the RAS Virtualization. See
commit 2afa8c8519: "hw/arm/virt: Introduce a RAS machine option").
Restrict the APEI tables generation code to the single user: the virt
machine. If another machine wants to use it, it simply has to 'select
ACPI_APEI' in its Kconfig.
Fixes: aa16508f1d ("ACPI: Build related register address fields via hardware error fw_cfg blob")
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Dongjiu Geng <gengdongjiu@huawei.com>
Acked-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20201008161414.2672569-1-philmd@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This implements a device model for the NPCM7xx SPI flash controller.
Direct reads and writes, and user-mode transactions have been tested in
various modes. Protection features are not implemented yet.
All the FIU instances are available in the SoC's address space,
regardless of whether or not they're connected to actual flash chips.
Reviewed-by: Tyrone Ting <kfting@nuvoton.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Alexander Bulekov <alxndr@bu.edu>
Signed-off-by: Havard Skinnemoen <hskinnemoen@google.com>
Message-id: 20200911052101.2602693-11-hskinnemoen@google.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Nuvoton NPCM7xx SoC family are used to implement Baseboard
Management Controllers in servers. While the family includes four SoCs,
this patch implements limited support for two of them: NPCM730 (targeted
for Data Center applications) and NPCM750 (targeted for Enterprise
applications).
This patch includes little more than the bare minimum needed to boot a
Linux kernel built with NPCM7xx support in direct-kernel mode:
- Two Cortex-A9 CPU cores with built-in periperhals.
- Global Configuration Registers.
- Clock Management.
- 3 Timer Modules with 5 timers each.
- 4 serial ports.
The chips themselves have a lot more features, some of which will be
added to the model at a later stage.
Reviewed-by: Tyrone Ting <kfting@nuvoton.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Alexander Bulekov <alxndr@bu.edu>
Signed-off-by: Havard Skinnemoen <hskinnemoen@google.com>
Message-id: 20200911052101.2602693-5-hskinnemoen@google.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Implement a device model for the System Global Control Registers in the
NPCM730 and NPCM750 BMC SoCs.
This is primarily used to enable SMP boot (the boot ROM spins reading
the SCRPAD register) and DDR memory initialization; other registers are
best effort for now.
The reset values of the MDLR and PWRON registers are determined by the
SoC variant (730 vs 750) and board straps respectively.
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Alexander Bulekov <alxndr@bu.edu>
Signed-off-by: Havard Skinnemoen <hskinnemoen@google.com>
Message-id: 20200911052101.2602693-2-hskinnemoen@google.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The USB_DWC2 switch is currently "default y", so it is included in all
qemu-system-* builds, even if it is not needed. Even worse, it does a
"select USB", so USB devices are now showing up as available on targets
that do not support USB at all. This sysbus device should only be
included by the boards that need it, i.e. by the Raspi machines.
Fixes: 153ef1662c ("dwc-hsotg (dwc2) USB host controller emulation")
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Paul Zimmerman <pauldzim@gmail.com>
Message-id: 20200722154719.10130-1-thuth@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
From 'Application Note AN385', chapter 3.14:
The SMM implements a simple SBCon interface based on I2C.
There are 4 SBCon interfaces on the FPGA APB subsystem.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20200617072539.32686-13-f4bug@amsat.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
From 'Application Note AN385', chapter 3.9, SPI:
The SMM implements five PL022 SPI modules.
Two pairs of modules share the same OR-gated IRQ.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20200617072539.32686-12-f4bug@amsat.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We already model the CMSDK APB watchdog device, let's use it!
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20200617072539.32686-9-f4bug@amsat.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
With this patch, the watchdog on i.MX31 emulations is fully operational.
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Message-id: 20200517162135.110364-5-linux@roeck-us.net
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
With this commit, the watchdog on imx25-pdk is fully operational,
including pretimeout support.
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Message-id: 20200517162135.110364-4-linux@roeck-us.net
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In preparation for a full implementation, move i.MX watchdog driver
from hw/misc to hw/watchdog. While at it, add the watchdog files
to MAINTAINERS.
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Message-id: 20200517162135.110364-2-linux@roeck-us.net
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This adds support to init nvdimm acpi state and build nvdimm acpi tables.
Please note nvdimm_support is not yet enabled.
Signed-off-by: Kwangwoo Lee <kwangwoo.lee@sk.com>
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Shameer Kolothum <shameerali.kolothum.thodi@huawei.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20200421125934.14952-4-shameerali.kolothum.thodi@huawei.com>
Acked-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add basic USB PHY support as implemented in i.MX23, i.MX28, i.MX6,
and i.MX7 SoCs.
The only support really needed - at least to boot Linux - is support
for soft reset, which needs to reset various registers to their initial
value. Otherwise, just record register values.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Message-id: 20200313014551.12554-2-linux@roeck-us.net
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Allwinner Sun8i System on Chip family includes an Ethernet MAC (EMAC)
which provides 10M/100M/1000M Ethernet connectivity. This commit
adds support for the Allwinner EMAC from the Sun8i family (H2+, H3, A33, etc),
including emulation for the following functionality:
* DMA transfers
* MII interface
* Transmit CRC calculation
Signed-off-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20200311221854.30370-10-nieklinnenbank@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Allwinner System on Chip families sun4i and above contain
an integrated storage controller for Secure Digital (SD) and
Multi Media Card (MMC) interfaces. This commit adds support
for the Allwinner SD/MMC storage controller with the following
emulated features:
* DMA transfers
* Direct FIFO I/O
* Short/Long format command responses
* Auto-Stop command (CMD12)
* Insert & remove card detection
The following boards are extended with the SD host controller:
* Cubieboard (hw/arm/cubieboard.c)
* Orange Pi PC (hw/arm/orangepi.c)
Signed-off-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20200311221854.30370-9-nieklinnenbank@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Allwinner H3 System on Chip contains multiple USB 2.0 bus
connections which provide software access using the Enhanced
Host Controller Interface (EHCI) and Open Host Controller
Interface (OHCI) interfaces. This commit adds support for
both interfaces in the Allwinner H3 System on Chip.
Signed-off-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20200311221854.30370-5-nieklinnenbank@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Allwinner H3 is a System on Chip containing four ARM Cortex A7
processor cores. Features and specifications include DDR2/DDR3 memory,
SD/MMC storage cards, 10/100/1000Mbit Ethernet, USB 2.0, HDMI and
various I/O modules. This commit adds support for the Allwinner H3
System on Chip.
Signed-off-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20200311221854.30370-2-nieklinnenbank@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Let the TPM TIS SYSBUS device be dynamically instantiable
in ARM virt. A device tree node is dynamically created
(TPM via MMIO).
The TPM Physical Presence interface (PPI) is not supported.
To run with the swtmp TPM emulator, the qemu command line must
be augmented with:
-chardev socket,id=chrtpm,path=swtpm-sock \
-tpmdev emulator,id=tpm0,chardev=chrtpm \
-device tpm-tis-device,tpmdev=tpm0 \
swtpm/libtpms command line example:
swtpm socket --tpm2 -t -d --tpmstate dir=/tmp/tpm \
--ctrl type=unixio,path=swtpm-sock
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Stefan Berger <stefanb@linux.ibm.com>
Tested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Message-id: 20200305165149.618-7-eric.auger@redhat.com
Signed-off-by: Stefan Berger <stefanb@linux.ibm.com>
The Linux kernel displays errors why trying to detect the PL041
audio interface:
Linux version 4.16.0 (linus@genomnajs) (gcc version 7.2.1 20171011 (Linaro GCC 7.2-2017.11)) #142 PREEMPT Wed May 9 13:24:55 CEST 2018
CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00093177
CPU: VIVT data cache, VIVT instruction cache
OF: fdt: Machine model: ARM Integrator/CP
...
OF: amba_device_add() failed (-19) for /fpga/aaci@1d000000
Since we have it already modelled, simply plug it.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20200223233033.15371-2-f4bug@amsat.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Alistair Francis <alistair@alistair23.me>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: ef941d59fd8658589d34ed432e1d6dfdcf7fb1d0.1576658572.git.alistair@alistair23.me
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This initializes the GED device with base memory and irq, configures
ged memory hotplug event and builds the corresponding aml code. With
this, both hot and cold plug of device memory is enabled now for Guest
with ACPI boot. Memory cold plug support with Guest DT boot is not yet
supported.
As DSDT table gets changed by this, update bios-tables-test-allowed-diff.h
to avoid "make check" failure.
Signed-off-by: Shameer Kolothum <shameerali.kolothum.thodi@huawei.com>
Message-Id: <20190918130633.4872-6-shameerali.kolothum.thodi@huawei.com>
Acked-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
This patch adds the memory hot-plug/hot-unplug infrastructure
in machvirt. The device memory is not yet exposed to the Guest
either through DT or ACPI and hence both cold/hot plug of memory
is explicitly disabled for now.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Kwangwoo Lee <kwangwoo.lee@sk.com>
Signed-off-by: Shameer Kolothum <shameerali.kolothum.thodi@huawei.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20190918130633.4872-5-shameerali.kolothum.thodi@huawei.com>
Acked-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The device is only used by some few boards. Let's use a proper Kconfig
switch so that we only compile this code if we really need it.
Message-Id: <20190817101931.28386-8-thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
The "split-irq" device is currently only used by machines that use
CONFIG_ARMSSE. Let's add a proper CONFIG_SPLIT_IRQ switch for this
so that it only gets compiled when we really need it.
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190817101931.28386-7-thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
The "or-irq" device is only used by certain machines. Let's add
a proper config switch for it so that it only gets compiled when we
really need it.
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190817101931.28386-6-thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
For AArch64, the existing "virt" machine is primarily meant to
run on KVM and execute virtualization workloads, but we need an
environment as faithful as possible to physical hardware, for supporting
firmware and OS development for physical Aarch64 machines.
This patch introduces new machine type 'sbsa-ref' with main features:
- Based on 'virt' machine type.
- A new memory map.
- CPU type cortex-a57.
- EL2 and EL3 are enabled.
- GIC version 3.
- System bus AHCI controller.
- System bus EHCI controller.
- CDROM and hard disc on AHCI bus.
- E1000E ethernet card on PCIE bus.
- VGA display adaptor on PCIE bus.
- No virtio devices.
- No fw_cfg device.
- No ACPI table supplied.
- Only minimal device tree nodes.
Arm Trusted Firmware and UEFI porting to this are done accordingly,
and the firmware should supply ACPI tables to the guest OS. The
minimal device tree nodes supplied by QEMU for this platform are only
to pass the dynamic info reflecting command line input to firmware,
not for loading the guest OS.
To make the review easier, this task is split into two patches, the
fundamental skeleton part and the peripheral devices part; this patch is
the first part.
Signed-off-by: Hongbo Zhang <hongbo.zhang@linaro.org>
Message-id: 1561890034-15921-2-git-send-email-hongbo.zhang@linaro.org
[PMM: commit message tweaks; moved some bits between patch 1 and 2
to ensure patch 1 builds cleanly; removed unneeded lines from
Kconfig stanza; only provide board for qemu-system-aarch64, not
qemu-system-arm; added MAINTAINERS entry]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Now we have two identical build_mcfg functions.
Consolidate them in acpi/pci.c.
Signed-off-by: Wei Yang <richardw.yang@linux.intel.com>
v4:
* ACPI_PCI depends on both ACPI and PCI
* rebase on latest master, adjust arm Kconfig
v3:
* adjust changelog based on Igor's suggestion
Message-Id: <20190521062836.6541-2-richardw.yang@linux.intel.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Dependencies have been determined with trial-and-error and by
looking at the musca.c source file.
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Dependencies have been determined with trial-and-error and by
looking at the xlnx-versal.c source file.
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
This cleans up most settings in default-configs/aarch64-softmmu.mak.
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Add Kconfig dependencies for the NRF51 / microbit machine.
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
IMX25, IMX7 and IMX6UL were still missing the Kconfig dependencies.
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Add Kconfig dependencies for the emcraft-sf2 machine - we also
distinguish between the machine (CONFIG_EMCRAFT_SF2) and the SoC
(CONFIG_MSF2) now.
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Add Kconfig dependencies for the Sabrelite / iMX6 machine.
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Add Kconfig dependencies for the DIGIC / canon-a1100 machine.
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Most of the code is directly controlled by the CONFIG_RASPI switch,
so not much to add here additionally.
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Add Kconfig dependencies for the mps2-an* machines.
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Add dependencies for the Cubitech Cubieboard.
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Netduino only depends on the stm32f205 SoC which in turn depends on
its components.
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Dependencies have been determined by looking at hw/arm/virt.c
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Dependencies have been determined by looking at hw/arm/aspeed.c
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Add Kconfig dependencies for the Strongarm collie machine.
This patch is based on earlier work by Ákos Kovács (i.e.
his "hw/arm/Kconfig: Add ARM Kconfig" patch).
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Philippe Mathieu-Daudé
Philippe Mathieu-Daudé
Andrew Jones
Peter Maydell
Shashi Mallela
Havard Skinnemoen
Thomas Huth
Guenter Roeck
Kwangwoo Lee
Niek Linnenbank
Eric Auger
Alistair Francis
Shameer Kolothum
Hongbo Zhang
Wei Yang