When virtio-vga was added, the intention was to only support it for
those machines where the firmware does not know about virtio-gpu,
and supported VGA legacy hardware before virtio-{gpu,vga} were
introduced.
The Kconfig switch however enabled virtio-vga for all machines with
a PCI bus, and libvirt then prefers it even on hardware where
virtio-gpu would be preferrable. At least for now, only enable
virtio-vga for PC, hppa and pSeries machines, as was the case
before Kconfig dependencies were introduced.
Reported-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
At least two machines, the PPC mac99 and MIPS fulong2e, have an ATI
gfx chip by default (Rage 128 Pro and M6/RV100 respectively) and
guests running on these and the PMON2000 firmware of the fulong2e
expect this to be available. Fortunately these are very similar chips
so they can be mostly emulated in the same device model. This patch
adds basic emulation of these ATI VGA chips.
While this is incomplete and currently only enough to run the MIPS
firmware and get framebuffer output with Linux, it allows the fulong2e
board to work more like the real hardware and having it in QEMU in
this state provides a way to experiment with it and allows others to
contribute to improve it. It is compiled for all archs but only the
fulong2e (which currently has no display output at all) is set to use
it by default (in a separate patch).
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Acked-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Tested-by: Andrew Randrianasulu <randrianasulu@gmail.com>
Tested-by: Howard Spoelstra <hsp.cat7@gmail.com>
Message-id: 0b1b7c22873a6e37627261b04fb687412b25ff4f.1552152100.git.balaton@eik.bme.hu
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190123065618.3520-42-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190123065618.3520-40-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Acked-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190123065618.3520-38-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Message-Id: <20190123065618.3520-36-yang.zhong@intel.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Instead of including the same list of devices for each target,
set CONFIG_PCI to true, and make the devices default to present
whenever PCI is available. However, s390x does not want all the
PCI devices, so there is a separate symbol to enable them.
Done mostly with the following script:
while read i; do
i=${i%=y}; i=${i#CONFIG_}
sed -i -e'/^config '$i'$/!b' -en \
-e'a\' -e' default y if PCI_DEVICES\' -e' depends on PCI' \
`grep -lw $i hw/*/Kconfig`
done < default-configs/pci.mak
followed by replacing a few "depends on" clauses with "select"
whenever the symbol is not really related to PCI.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190123065618.3520-31-yang.zhong@intel.com>
Acked-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The make_device_config.sh script is replaced by minikconf, which
is modified to support the same command line as its predecessor.
The roots of the parsing are default-configs/*.mak, Kconfig.host and
hw/Kconfig. One difference with make_device_config.sh is that all symbols
have to be defined in a Kconfig file, including those coming from the
configure script. This is the reason for the Kconfig.host file introduced
in the previous patch. Whenever a file in default-configs/*.mak used
$(...) to refer to a config-host.mak symbol, this is replaced by a
Kconfig dependency; this part must be done already in this patch
for bisectability.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Acked-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190123065618.3520-28-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The Kconfig files were generated mostly with this script:
for i in `grep -ho CONFIG_[A-Z0-9_]* default-configs/* | sort -u`; do
set fnord `git grep -lw $i -- 'hw/*/Makefile.objs' `
shift
if test $# = 1; then
cat >> $(dirname $1)/Kconfig << EOF
config ${i#CONFIG_}
bool
EOF
git add $(dirname $1)/Kconfig
else
echo $i $*
fi
done
sed -i '$d' hw/*/Kconfig
for i in hw/*; do
if test -d $i && ! test -f $i/Kconfig; then
touch $i/Kconfig
git add $i/Kconfig
fi
done
Whenever a symbol is referenced from multiple subdirectories, the
script prints the list of directories that reference the symbol.
These symbols have to be added manually to the Kconfig files.
Kconfig.host and hw/Kconfig were created manually.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Message-Id: <20190123065618.3520-27-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
