Currently this just floods indicating that can_receive has been called
by the net framework. Instead, save the result of the most recent
can_receive callback as state and only print a message if the result
changes (indicating some sort of actual state change in GEM). Make said
debug message more meaningful as well.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Message-id: 2eb74ca6a5756aea242d9f525961db95d6cfcf2c.1386136219.git.peter.crosthwaite@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This write-1-clear logic was incorrect. It was always clearing w1c
bits regardless of whether the written value was 1 or not. i.e. it
was implementing a write-anything-to-clear strategy.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: ed905b04d3343966ded425f06aa2224bc7a35b59.1386136219.git.peter.crosthwaite@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The minimum packet size is 64, however this is before FCS stripping
occurs. So when FCS stripping the minimum packet size is 60. Fix.
Reported-by: Deepika Dhamija <deepika@xilinx.com>
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Message-id: 8aac5bd737f9cf48b87f32943d7eb5939061e546.1386136219.git.peter.crosthwaite@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Bytes_to_copy was being updated before its final use where it
advances the rx buffer pointer. This was causing total mayhem,
where packet data for any subsequent fragments was being fetched
from the wrong place.
Reported-by: Deepika Dhamija <deepika@xilinx.com>
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: c2a1c65c1fd06eb274442a0fa4a6839d940e145e.1386136219.git.peter.crosthwaite@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Specific address registers can be enabled or disabled by software.
QEMU was assuming they were always enabled. Implement the
disable/enable feature. SARs are disabled by writing to the lower half
register. They are re-enabled by then writing the upper half.
Reported-by: Deepika Dhamija <deepika@xilinx.com>
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Message-id: 49efd1f7450af8f980b967d3054245bae137866c.1386136219.git.peter.crosthwaite@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Bit 27 of the RX buffer desc word 1 should be set when the packet was
accepted due to specific address register match. Implement.
This feature is absent from the Xilinx documentation (UG585) but the
behaviour is tested as accurate on real hardware.
Reported-by: Deepika Dhamija <deepika@xilinx.com>
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 7e3f26fc4ab244e8123efc12723e7164730abdcb.1386136219.git.peter.crosthwaite@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The various Rx packet address matching mode flags were not being set in
the rx descriptor. Implement.
Reported-by: Deepika Dhamija <deepika@xilinx.com>
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Message-id: 6002a24a6a8ceaa11d3009ab5392840d1c084b28.1386136219.git.peter.crosthwaite@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The real hardware prefetches rx buffer descriptors ASAP and
potentially throws relevant interrupts following the fetch
even in the absence of a received packet.
Reported-by: Deepika Dhamija <deepika@xilinx.com>
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Message-id: 41629e35edfdb1f02f1e401f2c3d0e2e4c9e44b3.1386136219.git.peter.crosthwaite@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
There was a replication of the rx descriptor address walking logic.
Reorder the flow control to remove. This refactoring also obsoletes
the local variables packet_desc_addr and last_desc_addr.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Message-id: 2a425b457ff0b57274bf206ad2236690cd7f5909.1386136219.git.peter.crosthwaite@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We were updating the ownership bit of all descriptors if packets
get split and written through several descriptors.
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: d61b7847b51487118783c93765a485bc5c66d272.1386136219.git.peter.crosthwaite@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Cadence GEM has a MAC level loopback mode. Implement. Use the same basic
operation as the already implemented PHY loopback.
Reported-by: Deepika Dhamija <deepika@xilinx.com>
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 3a0baf1b6b2fc1be638bdf1a37408ec38988e970.1386136219.git.peter.crosthwaite@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Rename variable qdev -> dev since that's what realize's argument is
called by convention.
Avoid duplicate VIRTIO_DEVICE() cast.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This ensures hot-unplug is handled properly by the proxy, and avoids
leaking bus_name which is freed by virtio_device_exit.
Cc: qemu-stable@nongnu.org
Acked-by: Andreas Faerber <afaerber@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
mac_table was always cleaned up first in handling
VIRTIO_NET_CTRL_MAC_TABLE_SET command, and we din't recover
mac_table content in error state, it's not correct.
This patch makes all the changes in temporal variables,
only update the real mac_table if everything is ok.
We won't change mac_table in error state, so rxfilter
notification isn't needed.
This patch also fixed same problame in
http://lists.nongnu.org/archive/html/qemu-devel/2013-11/msg01188.html
(not merge)
I will send patch for virtio spec to clarifying this change.
Signed-off-by: Amos Kong <akong@redhat.com>
Reviewed-by: Vlad Yasevich <vyasevic@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
This reverts commit cd5be5829c.
Digging into hardware specs shows this does not
actually make QEMU behave more like hardware:
There are valid arguments backed by the spec to indicate why the version
of e1000 prior to cd5be582 was more correct: the high byte actually
includes a valid bit, this is why all guests write it last.
For rtl8139 there's actually a separate undocumented valid bit, but we
don't implement it yet.
To summarize all the drivers we know about behave in one way
that allows us to make an assumption about write order and avoid
spurious, incorrect mac address updates to the monitor.
Let's stick to the tried heuristic for 1.7 and
possibly revisit for 1.8.
Reported-by: Vlad Yasevich <vyasevic@redhat.com>
Reviewed-by: Vlad Yasevich <vyasevic@redhat.com>
Cc: Amos Kong <akong@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# By Amos Kong (1) and Sebastian Huber (1)
# Via Stefan Hajnoczi
* stefanha/net:
virtio-net: fix the memory leak in rxfilter_notify()
smc91c111: Fix receive starvation
Message-id: 1384532032-19057-1-git-send-email-stefanha@redhat.com
Signed-off-by: Anthony Liguori <aliguori@amazon.com>
These are two patches that will hopefully make it into 1.7. The SLOF update
fixes -append kernel command line argument passing into the guest kernel. The
other patch makes VIO devices appear when using -device '?'.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=6SSx
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'agraf/tags/signed-ppc-for-upstream-1.7' into staging
Patch queue for ppc - 2013-11-08
These are two patches that will hopefully make it into 1.7. The SLOF update
fixes -append kernel command line argument passing into the guest kernel. The
other patch makes VIO devices appear when using -device '?'.
# gpg: Signature made Thu 07 Nov 2013 07:34:54 PM PST using RSA key ID 03FEDC60
# gpg: Can't check signature: public key not found
# By Alexey Kardashevskiy
# Via Alexander Graf
* agraf/tags/signed-ppc-for-upstream-1.7:
pseries: Update SLOF firmware image
spapr: add vio-bus devices to categories
Message-id: 1383881766-13958-1-git-send-email-agraf@suse.de
Signed-off-by: Anthony Liguori <aliguori@amazon.com>
object_get_canonical_path() returns a gchar*, it should be freed by the
caller.
Signed-off-by: Amos Kong <akong@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Vlad Yasevich <vyasevic@redhat.com>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
In case the smc91c111 interface signals that it cannot receive more
packets the packets are queued and further reception will be disabled.
In case the interface is again ready to receive packets notify the upper
layer.
Signed-off-by: Sebastian Huber <sebastian.huber@embedded-brains.de>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Upon processing of VIRTIO_NET_CTRL_MAC_TABLE_SET command
multicast list overwrites unicast list in mac_table.
This leads to broken logic for both unicast and multicast RX filtering.
Signed-off-by: Dmitry Fleytman <dfleytma@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
In order to get devices appear in output of
"./qemu-system-ppc64 -device ?",
they must be assigned to one of DEVICE_CATEGORY_XXXX.
This puts VIO devices classes to corresponding categories.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Alexander Graf <agraf@suse.de>
We currently just update the HMP NIC info when the last bit of macaddr
is written. This assumes that guest driver will write all the macaddr
from bit 0 to bit 5 when it changes the macaddr, this is the current
behavior of linux driver (e1000/rtl8139cp), but we can't do this
assumption.
The macaddr that is used for rx-filter will be updated when every bit
is changed. This patch updates the e1000/rtl8139 nic to update HMP NIC
info when every bit is changed. It will be same as virtio-net.
Signed-off-by: Amos Kong <akong@redhat.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Message-id: 1383650238-16015-1-git-send-email-akong@redhat.com
Signed-off-by: Anthony Liguori <aliguori@amazon.com>
We delete without check whether it existed during exit. This will lead NULL
pointer deference since it was created conditionally depends on guest driver
status and features. So add a check of existence before trying to delete it.
Cc: qemu-stable@nongnu.org
Signed-off-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-id: 1383728288-28469-1-git-send-email-jasowang@redhat.com
Signed-off-by: Anthony Liguori <aliguori@amazon.com>
Replace the legacy cpu_to_be32wu() with stl_be_p().
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-id: 1383669517-25598-8-git-send-email-peter.maydell@linaro.org
Signed-off-by: Anthony Liguori <aliguori@amazon.com>
Replace the legacy cpu_to_be16wu() with stw_be_p().
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-id: 1383669517-25598-7-git-send-email-peter.maydell@linaro.org
Signed-off-by: Anthony Liguori <aliguori@amazon.com>
Replace the legacy be32_to_cpupu() with ldl_be_p().
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-id: 1383669517-25598-6-git-send-email-peter.maydell@linaro.org
Signed-off-by: Anthony Liguori <aliguori@amazon.com>
Replace the legacy le32_to_cpupu() with ldl_le_p().
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-id: 1383669517-25598-5-git-send-email-peter.maydell@linaro.org
Signed-off-by: Anthony Liguori <aliguori@amazon.com>
Replace the legacy cpu_to_le32wu() with stl_le_p().
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-id: 1383669517-25598-3-git-send-email-peter.maydell@linaro.org
Signed-off-by: Anthony Liguori <aliguori@amazon.com>
This includes some pretty big changes:
- pci master abort support by Marcel
- pci IRQ API rework by Marcel
- acpi generation support by myself
Everything has gone through several revisions, latest versions have been on
list for a while without any more comments, tested by several
people.
Please pull for 1.7.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)
iQEcBAABAgAGBQJSXNO8AAoJECgfDbjSjVRp7VAH/0B73mCOiyVACGx7fazK3SGK
X8TxZWVtG5A77ISqKyrtjLAhK9DCQjEzQTbMNhXHM3Ar6crwo7nJZnQvH2Gh1X2p
34BOQSVc4rtXz5pwDIr48dBLrxeslwXub79chUs+IK1/4RSn3h3nuS3k6JVkmLJN
rcHMj4ljJmi4Hd9vOpmS1jo/a61usi36hhU7CMgcrsXzStZycBBzCozOB3VW8p1X
/iwyf91YjmNPkn9gA3/aViGjszu8jE91dkA0C+ljwvcGbs2yEl3LCWEJfsMvoh5P
2M+k0XXbHwq/P9PFMa/2/lWOo4EO4Oxa+G/6QvovJrteYnktr+E9DqjU8pCT7yI=
=CVfs
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'mst/tags/for_anthony' into staging
pci, pc, acpi fixes, enhancements
This includes some pretty big changes:
- pci master abort support by Marcel
- pci IRQ API rework by Marcel
- acpi generation support by myself
Everything has gone through several revisions, latest versions have been on
list for a while without any more comments, tested by several
people.
Please pull for 1.7.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Tue 15 Oct 2013 07:33:48 AM CEST using RSA key ID D28D5469
# gpg: Can't check signature: public key not found
* mst/tags/for_anthony: (39 commits)
ssdt-proc: update generated file
ssdt: fix PBLK length
i386: ACPI table generation code from seabios
pc: use new api to add builtin tables
acpi: add interface to access user-installed tables
hpet: add API to find it
pvpanic: add API to access io port
ich9: APIs for pc guest info
piix: APIs for pc guest info
acpi/piix: add macros for acpi property names
i386: define pc guest info
loader: allow adding ROMs in done callbacks
i386: add bios linker/loader
loader: use file path size from fw_cfg.h
acpi: ssdt pcihp: updat generated file
acpi: pre-compiled ASL files
acpi: add rules to compile ASL source
i386: add ACPI table files from seabios
q35: expose mmcfg size as a property
q35: use macro for MCFG property name
...
Message-id: 1381818560-18367-1-git-send-email-mst@redhat.com
Signed-off-by: Anthony Liguori <anthony@codemonkey.ws>
rtl8139 has same problem as e1000, nic info isn't updated when macaddr
is changed in guest.
This patch updates the nic info when the last bit of macaddr is written.
Signed-off-by: Amos Kong <akong@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
If we change macaddr in guest by 'ifconfig eth0 hw ether 12:12:12:34:35:36',
the mac register of e1000 is already updated, but we don't update
network information in qemu. Therefor, the information in monitor
is wrong.
This patch updates nic info when the second part of macaddr is written.
Signed-off-by: Amos Kong <akong@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
macaddr is reset during device reset, but nic info
isn't updated, this problem exists in e1000 & rtl8139
Signed-off-by: Amos Kong <akong@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
pci_set_irq and the other pci irq wrappers use
PCI_INTERRUPT_PIN config register to compute device
INTx pin to assert/deassert.
An irq is allocated using pci_allocate_irq wrapper
only if is needed by non pci devices.
Removed irq related fields from state if not used anymore.
Signed-off-by: Marcel Apfelbaum <marcel.a@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
pci_set_irq uses PCI_INTERRUPT_PIN config register
to compute device INTx pin to assert/deassert.
An assert is used to ensure that intx received
from the quest OS corresponds to PCI_INTERRUPT_PIN.
Signed-off-by: Marcel Apfelbaum <marcel.a@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This includes pc and pci cleanups and enhancements,
and a virtio-net bugfix related to softmac programming.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)
iQEcBAABAgAGBQJSR83kAAoJECgfDbjSjVRpX08H/jKgYBNJaChev1TROIVHEGbu
IzvkjfocvKO+6wmhOf5x+xwFmzrijUMa1CPvOkCp8c2A3Iek7rmnedknlhXYh7dM
z5mXcvFGjnu7ST38ydF/Emk9+Z6rRg5Y/hkmlDyr+9lNcoiCDLXXcUrKjeIHNoWl
e8w3yiPCJ528QyrLwQ890XetJphv67pMlsjMgLQ2betMk++Ac/ctUf1D2p1X4NeQ
Q2drbo5Z4yDk0i6QMA3iLq1Bh/AhE10bCDq9rCzfZGIKVyncL6ne2pSi/xDvpLrF
dmxoiJ5QrK6xLnagCcn5T6SB9DkwbEPdL7qCqlxZ8USr7cVyPdzYtHtGSBWdeXY=
=xF01
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'mst/tags/for_anthony' into staging
pc,pci,virtio fixes and cleanups
This includes pc and pci cleanups and enhancements,
and a virtio-net bugfix related to softmac programming.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Sun 29 Sep 2013 01:51:16 AM CDT using RSA key ID D28D5469
# gpg: Can't check signature: public key not found
# By Michael S. Tsirkin (8) and others
# Via Michael S. Tsirkin
* mst/tags/for_anthony:
smbios: Factor out smbios_maybe_add_str()
smbios: Make multiple -smbios type= accumulate sanely
smbios: Improve diagnostics for conflicting entries
smbios: Convert to QemuOpts
smbios: Normalize smbios_entry_add()'s error handling to exit(1)
virtio-net: fix up HMP NIC info string on reset
pci: remove explicit check to 64K ioport size
piix4: disable io on reset
piix: use 64 bit window programmed by guest
q35: use 64 bit window programmed by guest
pci: add helper to retrieve the 64-bit range
range: add min/max operations on ranges
range: add Range to typedefs
q35: make pci window address/size match guest cfg
Message-id: 1380437951-21788-1-git-send-email-mst@redhat.com
This patch implements the NetClientInfo.receive_iov method for the
e1000 device emulation. In this way a network backend that uses
qemu_sendv_packet() can deliver the fragmented packet without
requiring an additional copy in the frontend/backend network code
(nc_sendv_compat() function).
The existing method NetClientInfo.receive has been reimplemented
using the new method.
Signed-off-by: Vincenzo Maffione <v.maffione@gmail.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Now that the memory subsystem is propagating the endianness correctly,
the pcnet-pci device should have its I/O ports and MMIO memory marked
as LITTLE_ENDIAN, as PCI devices are little endian.
This makes the pcnet-pci NIC to work again on big endian MIPS Malta
(default NIC).
Cc: qemu-stable@nongnu.org
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Now that the memory subsystem is propagating the endianness correctly,
the ne2000 device should have its I/O ports marked as LITTLE_ENDIAN, as
PCI devices are little endian.
This makes the ne2000 NIC to work again on PowerPC.
Cc: qemu-stable@nongnu.org
Cc: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
This eliminates a warning about __packed being redefined as exposed by the
vmxnet3 code. __packed is not used anywhere in the vmxnet3 code.
CC hw/net/vmxnet3.o
In file included from hw/net/vmxnet3.c:29:
hw/net/vmxnet3.h:37:1: warning: "__packed" redefined
In file included from /usr/include/stdlib.h:38,
from /buildbot-qemu/default_openbsd_current/build/include/qemu-common.h:26,
from /buildbot-qemu/default_openbsd_current/build/include/hw/hw.h:5,
from hw/net/vmxnet3.c:18:
/usr/include/sys/cdefs.h:209:1: warning: this is the location of the previous definition
Signed-off-by: Brad Smith <brad@comstyle.com>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
This patch partially implements the e1000 interrupt mitigation mechanisms.
Using a single QEMUTimer, it emulates the ITR register (which is the newer
mitigation register, recommended by Intel) and approximately emulates
RADV and TADV registers. TIDV and RDTR register functionalities are not
emulated (RDTR is only used to validate RADV, according to the e1000 specs).
RADV, TADV, TIDV and RDTR registers make up the older e1000 mitigation
mechanism and would need a timer each to be completely emulated. However,
a single timer has been used in order to reach a good compromise between
emulation accuracy and simplicity/efficiency.
The implemented mechanism can be enabled/disabled specifying the command
line e1000-specific boolean parameter "mitigation", e.g.
qemu-system-x86_64 -device e1000,mitigation=on,... ...
For more information, see the Software developer's manual at
http://download.intel.com/design/network/manuals/8254x_GBe_SDM.pdf.
Interrupt mitigation boosts performance when the guest suffers from
an high interrupt rate (i.e. receiving short UDP packets at high packet
rate). For some numerical results see the following link
http://info.iet.unipi.it/~luigi/papers/20130520-rizzo-vm.pdf
Signed-off-by: Vincenzo Maffione <v.maffione@gmail.com>
Reviewed-by: Andreas Färber <afaerber@suse.de> (for pc-* machines)
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
To be passed on to object_initialize_with_type().
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com> (virtio-ccw)
Signed-off-by: Andreas Färber <afaerber@suse.de>
This is an autogenerated patch using scripts/switch-timer-api.
Switch the entire code base to using the new timer API.
Note this patch may introduce some line length issues.
Signed-off-by: Alex Bligh <alex@alex.org.uk>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Analogously to other NICs, we have to inform the network layer when
the can_receive handler will no longer report 0. Without this, we may
get stuck waiting on queued incoming packets.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
'dprintf' is the name of a POSIX standard function so we should not be
stealing it for our debug macro. Rename to 'DPRINTF' (in line with
a number of other source files.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: MORITA Kazutaka <morita.kazutaka@lab.ntt.co.jp>
Acked-by: Richard Henderson <rth@twiddle.net>
Acked-by: Kevin Wolf <kwolf@redhat.com>
Message-id: 1375100199-13934-5-git-send-email-peter.maydell@linaro.org
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Drop freeing stellaris_enet_state - that is done by QOM later on unref.
Both MemoryRegion init and savevm registration happen in SysBusDevice
initfn currently, so move them into an unrealizefn for now.
Signed-off-by: Andreas Färber <afaerber@suse.de>
The category will be used to sort the devices displayed in
the command line help.
Signed-off-by: Marcel Apfelbaum <marcel.a@redhat.com>
Message-id: 1375107465-25767-4-git-send-email-marcel.a@redhat.com
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Made small tweaks in code to prevent compilation issues
when importing qemu/bitmap.h in qdev-core
Signed-off-by: Marcel Apfelbaum <marcel.a@redhat.com>
Message-id: 1375107465-25767-2-git-send-email-marcel.a@redhat.com
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This patch adds the necessary VMStateDescription information to support
savevm/loadvm for the spapr_llan (PAPR logical lan) device.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Anthony Liguori <aliguori@us.ibm.com>
Message-id: 1374175984-8930-4-git-send-email-aliguori@us.ibm.com
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
The macro g_assert_not_reached is a better self documenting replacement
for assert(0) or assert(false).
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Define and use standard QOM cast macro. Remove usages of DO_UPCAST()
and direct -> style upcasting.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
[AF: Renamed parent field, renamed from PC_NET to PCNET]
Signed-off-by: Andreas Färber <afaerber@suse.de>
Replace direct uses of RTL8139State::dev with QOM casts and rename it to
parent_obj.
Acked-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Define and use standard QOM cast macro. Remove usages of DO_UPCAST()
and direct -> style upcasting.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Replace direct uses of E1000State::dev field with QOM casts and rename
it to parent_obj.
Acked-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Define and use standard QOM cast macro. Remove usages of DO_UPCAST()
and direct -> style upcasting.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
# By Markus Armbruster
# Via Stefan Hajnoczi
* stefanha/tracing:
trace-events: Fix up source file comments
trace-events: Drop unused events
milkymist-minimac2: Fix minimac2_read/_write tracepoints
slavio_misc: Fix slavio_led_mem_readw/_writew tracepoints
cleanup-trace-events.pl: New
Message-id: 1374119369-26496-1-git-send-email-stefanha@redhat.com
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This includes some fixes and enhancements that accumulated in my tree:
pci fixes by dkoch, virtio-net enhancements by akong and mst,
and a fix for xen pc by mst.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)
iQEcBAABAgAGBQJR5meNAAoJECgfDbjSjVRp24IIAMOkxbb85FJ323G/x5cQBzA/
gjFDmvB6geIMBorX1YZRnIM+RFhx+mkXtBTu2raWVTNTt5G2u3vAQQWW2zSiOTBL
gH4BhzJnUoqLHOydWql2MsGS7DMQo4Fq8OnzRBkZ119AEEqNMad1w2LykwFWs4ra
k3bsPNCZM+ZNiLMWtQLOcD3FYvoiISinqFd81KOnxvDiT90rczk4dLWqjv8smNif
WqZ7aCD1hGJ5yD7JI2YjCbhVvu4F7tBK+fWkT/O3oYslh/o241lyxUriOXMKdKML
04sNXa5eWue9cOKlbo1G+yfFwFg1JDsAMe/Usg0KXz1MMK91wiWE763ESPbFBK0=
=P+pr
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'mst/tags/for_anthony' into staging
pci,net,pc enhancements
This includes some fixes and enhancements that accumulated in my tree:
pci fixes by dkoch, virtio-net enhancements by akong and mst,
and a fix for xen pc by mst.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Wed 17 Jul 2013 04:44:45 AM CDT using RSA key ID D28D5469
# gpg: Can't check signature: public key not found
# By Don Koch (2) and others
# Via Michael S. Tsirkin
* mst/tags/for_anthony:
pc: don't access fw cfg if NULL
virtio-net: add feature bit for any header s/g
net: add support of mac-programming over macvtap in QEMU side
pci: fix BRDIGE typo
pci-bridge: update mappings for migration/restore
Message-id: 1374054430-21966-1-git-send-email-mst@redhat.com
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Broken in milkymist-minimac.c from the start (commit 0742454),
faithfully moved to milkymist-minimac2.c (commit 57aa265).
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Currently macvtap based macvlan device is working in promiscuous
mode, we want to implement mac-programming over macvtap through
Libvirt for better performance.
Design:
QEMU notifies Libvirt when rx-filter config is changed in guest,
then Libvirt query the rx-filter information by a monitor command,
and sync the change to macvtap device. Related rx-filter config
of the nic contains main mac, rx-mode items and vlan table.
This patch adds a QMP event to notify management of rx-filter change,
and adds a monitor command for management to query rx-filter
information.
Test:
If we repeatedly add/remove vlan, and change macaddr of vlan
interfaces in guest by a loop script.
Result:
The events will flood the QMP client(management), management takes
too much resource to process the events.
Event_throttle API (set rate to 1 ms) can avoid the events to flood
QMP client, but it could cause an unexpected delay (~1ms), guests
guests normally expect rx-filter updates immediately.
So we use a flag for each nic to avoid events flooding, the event
is emitted once until the query command is executed. The flag
implementation could not introduce unexpected delay.
There maybe exist an uncontrollable delay if we let Libvirt do the
real change, guests normally expect rx-filter updates immediately.
But it's another separate issue, we can investigate it when the
work in Libvirt side is done.
Michael S. Tsirkin: tweaked to enable events on start
Michael S. Tsirkin: fixed not to crash when no id
Michael S. Tsirkin: fold in patch:
"additional fixes for mac-programming feature"
Amos Kong: always notify QMP client if mactable is changed
Amos Kong: return NULL list if no net client supports rx-filter query
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Amos Kong <akong@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This includes some pci enhancements:
Better support for systems with multiple PCI root buses
FW cfg interface for more robust pci programming in BIOS
Minor fixes/cleanups for fw cfg and cross-version migration -
because of dependencies with other patches
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)
iQEcBAABAgAGBQJR2ctmAAoJECgfDbjSjVRpQpAH/Rk00yLrQ2R5ScNa8AL9LeaJ
gVFndBmmuRz4gdhyATx6lzR98ic32iTr0+YR5mL51btgmM5a0bEd/SIu34nXriWj
PsM0wdXfo/oEygdttxhvzJOH17tohRV9xg2WA2d8BEwDzrDyqoQ4J0VJlHlG7u3W
nq4KVDVUpLNQFKG8ZgJ2vW0WMw/mBSj2rluhQUALhcuvChphtvAFZ2rsSfJr6bzD
aBELrtIvfLvPGN/0WVeYs9qlp4EE03H3X6gN61QvV3/YElxubKUV5XyMDOX2dW3D
2j0NQi84LYHn0SFap2r/Kgm47/F6Q56SFk5lrgZrg60mhQTwocw7PfL8CGxjXRI=
=gxxc
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'mst/tags/for_anthony' into staging
pci,misc enhancements
This includes some pci enhancements:
Better support for systems with multiple PCI root buses
FW cfg interface for more robust pci programming in BIOS
Minor fixes/cleanups for fw cfg and cross-version migration -
because of dependencies with other patches
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Sun 07 Jul 2013 03:11:18 PM CDT using RSA key ID D28D5469
# gpg: Can't check signature: public key not found
# By David Gibson (10) and others
# Via Michael S. Tsirkin
* mst/tags/for_anthony:
pci: Fold host_buses list into PCIHostState functionality
pci: Remove domain from PCIHostBus
pci: Simpler implementation of primary PCI bus
pci: Add root bus parameter to pci_nic_init()
pci: Add root bus argument to pci_get_bus_devfn()
pci: Replace pci_find_domain() with more general pci_root_bus_path()
pci: Use helper to find device's root bus in pci_find_domain()
pci: Abolish pci_find_root_bus()
pci: Move pci_read_devaddr to pci-hotplug-old.c
pci: Cleanup configuration for pci-hotplug.c
pvpanic: fix fwcfg for big endian hosts
pvpanic: initialization cleanup
MAINTAINERS: s/Marcelo/Paolo/
e1000: cleanup process_tx_desc
pc_piix: cleanup init compat handling
pc: pass PCI hole ranges to Guests
pci: store PCI hole ranges in guestinfo structure
range: add Range structure
Message-id: 1373228271-31223-1-git-send-email-mst@redhat.com
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Coverity complains about two overruns in process_tx_desc(). The
complaints are false positives, but we might as well eliminate
them. The problem is that "hdr" is defined as an unsigned int,
but then used to offset an array of size 65536, and another of
size 256 bytes. hdr will actually never be greater than 255
though, as it's assigned only once and to the value of
tp->hdr_len, which is an uint8_t. This patch simply gets rid of
hdr, replacing it with tp->hdr_len, which makes it consistent
with all other tp member use in the function.
v2:
- also cleanup coding style issues in the touched lines
Signed-off-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
* 'realize-isa.v2' of git://github.com/afaerber/qemu-cpu:
qdev: Drop FROM_QBUS() macro
isa: QOM'ify ISADevice
isa: QOM'ify ISABus
i8259: Convert PICCommonState to use QOM realizefn
kvm/i8259: QOM'ify some more
i8259: QOM'ify some more
i8254: Convert PITCommonState to QOM realizefn
kvm/i8254: QOM'ify some more
i8254: QOM'ify some more
isa: Use realizefn for ISADevice
cs4231a: QOM'ify some more
gus: QOM'ify some more
# By Jason Wang (1) and Stefan Hajnoczi (1)
# Via Stefan Hajnoczi
* stefanha/net:
tap: fix NULL dereference when passing invalid parameters to tap
vmxnet3: fix NICState cleanup
Message-id: 1370613288-14933-1-git-send-email-stefanha@redhat.com
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Obviously the code wanted to mask the lower bits but failed to do so
because of a missing "<".
cppcheck detected a conditional expression which was always true (1 < 7).
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@gmail.com>
Drop ISADeviceClass::init and the resulting no-op initfn and let
children implement their own realizefn. Adapt error handling.
Split off an instance_init where sensible.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Use qemu_del_nic() instead of qemu_del_net_client() to correctly free
the entire NICState.
Cc: qemu-stable@nongnu.org
Reported-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Net queues support efficient "receive disable". For example, tap's file
descriptor will not be polled while its peer has receive disabled. This
saves CPU cycles for needlessly copying and then dropping packets which
the peer cannot receive.
rtl8139 is missing the qemu_flush_queued_packets() call that wakes the
queue up when receive becomes possible again.
As a result, the Windows 7 guest driver reaches a state where the
rtl8139 cannot receive packets. The driver has actually refilled the
receive buffer but we never resume reception.
The bug can be reproduced by running a large FTP 'get' inside a Windows
7 guest:
$ qemu -netdev tap,id=tap0,...
-device rtl8139,netdev=tap0
The Linux guest driver does not trigger the bug, probably due to a
different buffer management strategy.
Reported-by: Oliver Francke <oliver.francke@filoo.de>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Virtio-net driver currently negotiates network offloads
on startup via features mechanism and have no ability to
disable and re-enable offloads later.
This patch introduced a new control command that allows
to configure device network offloads state dynamically.
The patch also introduces a new feature flag
VIRTIO_NET_F_CTRL_GUEST_OFFLOADS.
Signed-off-by: Dmitry Fleytman <dfleytma@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Message-id: 20130520081814.GA8162@redhat.com
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This adds virtio_net_set_netclient_name, which is used to set the
name and type shown in "info network" command.
Signed-off-by: KONRAD Frederic <fred.konrad@greensocs.com>
Message-id: 1368619970-23892-2-git-send-email-fred.konrad@greensocs.com
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Commit 32993698 (vhost: disable on tap link down) tries to disable the vhost
also when the peer's link is down. But the check was not done properly, the
vhost were only started when:
1) peer's link is not down
2) virtio-net has already been started.
Since == have a higher precedence than &&, place a brace to make sure both the
conditions were met then does the check. This fixes the crash when doing a savem
after set the link off which let qemu crash and complains:
virtio_net_save: Assertion `!n->vhost_started' failed.
Cc: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Message-id: 1366972060-21606-1-git-send-email-jasowang@redhat.com
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Normally, the "tap" device is polled by QEMU if a guest NIC can
receive packets. If a guest NIC is stopped during transfer (rmmod or
ifdown), it may still have packets in a queue which have to be send
to the guest before QEMU enables polling of a "tap" interface via
tap_update_fd_handler().
However the spapr_llan device was missing the qemu_flush_queued_packets()
call so the tap_send_completed() callback was never called and therefore
"tap" interface polling was not enabled ever.
The patch fixes this problem.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Alexander Graf <agraf@suse.de>
Commit 14f9b664 (hw/virtio-net.c: set config size using host features) tries to
calculate config size based on the host features. But it forgets the
VIRTIO_NET_F_MAC were always set for qemu later. This will lead a zero config
len for virtio-net device when both VIRTIO_NET_F_STATUS and VIRTIO_NET_F_MQ were
disabled form command line. Then qemu will crash when user tries to read the
config of virtio-net.
Fix this by counting VIRTIO_NET_F_MAC and make sure the config at least contains
the mac address.
Cc: Jesse Larrew <jlarrew@linux.vnet.ibm.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Message-id: 1366874814-2658-1-git-send-email-jasowang@redhat.com
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Introduce type constant and cast macro to obsolete DO_UPCAST().
Prepares for ISA realizefn.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Message-id: 1367093935-29091-10-git-send-email-afaerber@suse.de
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Multiqueue patchset conditionally add control vq only when guest negotiate the
feature. Though the spec is not clear on this but it breaks the minix guest
since it will identify the ctrl vq even if it does not support it. Though this
behavior seems a violation on the spec "If the VIRTIO_NET_F_CTRL_VQ feature bit
is negotiated, identify the control virtqueue.", to keep the backward
compatibility, always add the ctrl vq at end of the queues.
Reported-by: Aurelien Jarno <aurelien@aurel32.net>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Message-id: 1366874663-2566-1-git-send-email-jasowang@redhat.com
Cc: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Curerntly the pseries VIO device code contains quite a few explicit
uses of DO_UPCAST and plain C casts. This is (obviously) type unsafe,
and not the conventional way of doing things in the QOM model. This
patch converts the code to use the QOM convention of per-type macros
to do verified casts with OBJECT_CHECK().
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alexander Graf <agraf@suse.de>
This clean the init and the exit functions and rename virtio_common_cleanup
to virtio_cleanup.
Signed-off-by: KONRAD Frederic <fred.konrad@greensocs.com>
Message-id: 1366791683-5350-7-git-send-email-fred.konrad@greensocs.com
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This remove virtio-bindings, and use class instead.
Signed-off-by: KONRAD Frederic <fred.konrad@greensocs.com>
Message-id: 1366791683-5350-6-git-send-email-fred.konrad@greensocs.com
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This remove the function pointer in VirtIODevice, and use only
VirtioDeviceClass function pointer.
Signed-off-by: KONRAD Frederic <fred.konrad@greensocs.com>
Message-id: 1366791683-5350-5-git-send-email-fred.konrad@greensocs.com
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Drop all the infrastructure for taddr properties (ie ones which
are 'hwaddr' sized). These are now unused, and any further desired
use would be rather questionable since device properties shouldn't
generally depend on a type that is conceptually variable based on
the target CPU. 32 or 64 bit integer properties should be used instead
as appropriate for the specific device.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
cpu_physical_memory_read, cpu_physical_memory_write take any pointer
as 2nd argument without needing a type cast.
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
