The code that gets run at the end of the migration process
is getting large, and I'm about to add more for postcopy.
Split it into a separate function.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <1439463094-5394-3-git-send-email-dgilbert@redhat.com>
Reviewed-by: zhanghailiang <zhang.zhanghailiang@huawei.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
RAM migration mainly works on RAMBlocks but in a few places
uses data from MemoryRegions to access the same information that's
already held in RAMBlocks; clean it up just to avoid the
MemoryRegion use.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <1439463094-5394-2-git-send-email-dgilbert@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
The free() and g_free() functions both happily accept
NULL on any platform QEMU builds on. As such putting a
conditional 'if (foo)' check before calls to 'free(foo)'
merely serves to bloat the lines of code.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Many source files have doubled words (eg "the the", "to to",
and so on). Most of these can simply be removed, but a couple
were actual mis-spellings (eg "to to" instead of "to do").
There was even one triple word score "to to to" :-)
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
When doing migration via the QMP command xen_save_devices_state, the
current runstate is not store into the global state section. Also the
current runstate is not the one we want on the receiver side.
During migration, the Xen toolstack paused QEMU before save the devices
state. Also, the toolstack expect QEMU to autostart when the migration is
finished.
So this patch store "running" as it's current runstate.
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
The error checks I added used 'break' after the error, but I'm
in a switch inside the while loop, so they need to be 'goto out'.
Spotted by coverity; entries 1311368 and 1311369
Fixes: afcddefd
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <1436555332-19076-1-git-send-email-dgilbert@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Commit df4b102452 introduced global_state
section. But it only filled the state while doing migration. While
doing a savevm, we stored an empty string as state. So when we did a
loadvm, it complained that state was invalid.
Fedora 21, 4.1.1, qemu 2.4.0-rc0
> ../../configure --target-list="x86_64-softmmu"
068 2s ... - output mismatch (see 068.out.bad)
--- /home/bos/jhuston/src/qemu/tests/qemu-iotests/068.out 2015-07-08
17:56:18.588164979 -0400
+++ 068.out.bad 2015-07-09 17:39:58.636651317 -0400
@@ -6,6 +6,8 @@
QEMU X.Y.Z monitor - type 'help' for more information
(qemu) savevm 0
(qemu) quit
+qemu-system-x86_64: Unknown savevm section or instance 'globalstate' 0
+qemu-system-x86_64: Error -22 while loading VM state
QEMU X.Y.Z monitor - type 'help' for more information
(qemu) quit
*** done
Failures: 068
Failed 1 of 1 tests
Actually, there were two problems here:
- we registered global_state too late for load_vm (fixed on another
patch on the list)
- we didn't store a valid state for savevm (fixed by this patch).
Reported-by: John Snow <jsnow@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Tested-by: Christian Borntraeger <borntraeger@de.ibm.com>
'strlen' is called three times in 'save_page_header', it's
inefficient.
Signed-off-by: Liang Li <liang.z.li@intel.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
We can want the trace event even without migration events enabled.
Reported-by: Wen Congyang <ghostwcy@gmail.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
On previous change, we changed state at post load time if it was not
running, special casing the "running" change. Now, we change any states
at the end of the migration.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Tested-by: Christian Borntraeger <borntraeger@de.ibm.com>
migration_end calls synchronize_rcu() within a critical section.
That causes a deadlock; move the call after rcu_read_unlock().
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
There callers work on a single BlockDriverState subtree, where using
bdrv_drain() is more accurate.
Signed-off-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Prevously, if we hotplug a device(e.g. device_add e1000) during
migration is processing in source side, qemu will add a new ram
block but migration_bitmap is not extended.
In this case, migration_bitmap will overflow and lead qemu abort
unexpectedly.
Signed-off-by: Li Zhijian <lizhijian@cn.fujitsu.com>
Signed-off-by: Wen Congyang <wency@cn.fujitsu.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
The section footers check was incorrectly checking the section_id
in the SaveStateEntry not the LoadStateEntry. These can validly be different
if the two QEMU instances have instantiated their devices in a
different order. The test only cares that we're finishing the same
section we started, and hence it's the LoadStateEntry that we care about.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reported-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
We reuse the migration events from the source side, sending them on the
appropiate place.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Make check fails with events. THis is due to the parser/lexer that it
uses. Just in case that they are more broken parsers, just only send
events when there are capabilities.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
We have one argument that tells us what event has happened.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
We now use the helper everywhere, so no need to call this on this two
places. See on previous commit that there were a place where we missed
to mark the trace. Now all tracing is done in migrate_set_state().
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
There were three places that were not using the migrate_set_state()
helper, just fix that.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
It needs to be the first one and it is not optional, that is the reason
why it is opencoded. For new machine types, it is required that machine
type name is the same in both sides.
It is just done right now for pc's.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
To make sections optional, we need to do it at the beggining of the code.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
This section would be sent:
a- for all new machine types
b- for old machine types if section state is different form {running,paused}
that were the only giving us troubles.
So, in new qemus: it is alwasy there. In old qemus: they are only
there if it an error has happened, basically stoping on target.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
This includes a new section that for now just stores the current qemu state.
Right now, there are only one way to control what is the state of the
target after migration.
- If you run the target qemu with -S, it would start stopped.
- If you run the target qemu without -S, it would run just after migration finishes.
The problem here is what happens if we start the target without -S and
there happens one error during migration that puts current state as
-EIO. Migration would ends (notice that the error happend doing block
IO, network IO, i.e. nothing related with migration), and when
migration finish, we would just "continue" running on destination,
probably hanging the guest/corruption data, whatever.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
If the number of RAMBlocks was different on the source from the
destination, QEMU would hang waiting for a disconnect on the source
and wouldn't release from that hang until the destination was manually
killed.
Mark the stream as being in error, this causes the destination to die
and the source to carry on.
(It still gets a whole bunch of warnings on the destination, and I've
not managed to complete another migration after the 1st one, still
progress).
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Perform some basic (but probably not complete) sanity checking on
requests from the RDMA source.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Michael R. Hines <mrhines@us.ibm.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Use the order of incoming RAMBlocks from the source to record
an index number; that then allows us to sort the destination
local RAMBlock list to match the source.
Now that the RAMBlocks are known to be in the same order, this
simplifies the RDMA Registration step which previously tried to
match RAMBlocks based on offset (which isn't guaranteed to match).
Looking at the existing compress code, I think it was erroneously
relying on an assumption of matching ordering, which this fixes.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
RDMA uses a hash from block offset->RAM Block; this isn't needed
on the destination, and it becomes harder to maintain after the next
patch in the series that sorts the block list.
Split the hash so that it's only generated on the source.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
In the next patch we remove the hash on the destination,
rdma_delete_block does two things with the hash which can be avoided:
a) The caller passes the offset and rdma_delete_block looks it up
in the hash; fixed by getting the caller to pass the block
b) The hash gets recreated after deletion; fixed by making that
conditional on the hash being initialised.
While this function is currently only used during cleanup, Michael
asked that we keep it general for future dynamic block registration
work.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
We need the names of RAMBlocks as they're loaded for RDMA,
reuse a slightly modified ram_control_load_hook:
a) Pass a 'data' parameter to use for the name in the block-reg
case
b) Only some hook types now require the presence of a hook function.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
The 'offset' field in RDMACompress and 'current_addr' field
in RDMARegister are commented as being offsets within a particular
RAMBlock, however they appear to actually be offsets within the
ram_addr_t space.
The code currently assumes that the offsets on the source/destination
match, this change removes the need for the assumption for these
structures by translating the addresses into the ram_addr_t space of
the destination host.
Note: An alternative would be to change the fields to actually
take the data they're commented for; this would potentially be
simpler but would break stream compatibility for those cases
that currently work.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
In a later patch the block name will be used to match up two views
of the block list. Keep a copy of the block name with the local block
list.
(At some point it could be argued that it would be best just to let
migration see the innards of RAMBlock and avoid the need to use
foreach).
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Michael R. Hines <mrhines@us.ibm.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
The VMDescription section maybe after the EOF mark, the current code
does a 'qemu_get_byte' and either gets the header byte identifying the
description or an error (which it ignores). Doing the 'get' upsets
RDMA which hangs on old machine types without the VMDescription.
Just avoid reading the VMDescription if we wouldn't send it.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Variable "r" going out of scope leaks the storage
it points to in line 3268.
Signed-off-by: Gonglei <arei.gonglei@huawei.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
In particular, don't include it into headers.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Luiz Capitulino <lcapitulino@redhat.com>
In particular, don't include it into headers.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Luiz Capitulino <lcapitulino@redhat.com>
These macros expand into error class enumeration constant, comma,
string. Unclean. Has been that way since commit 13f59ae.
The error class is always ERROR_CLASS_GENERIC_ERROR since the previous
commit.
Clean up as follows:
* Prepend every use of a QERR_ macro by ERROR_CLASS_GENERIC_ERROR, and
delete it from the QERR_ macro. No change after preprocessing.
* Rewrite error_set(ERROR_CLASS_GENERIC_ERROR, ...) into
error_setg(...). Again, no change after preprocessing.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Luiz Capitulino <lcapitulino@redhat.com>
Version: GnuPG v1
iQEcBAABAgAGBQJVetcwAAoJEJykq7OBq3PI+84IAMfkE0uCXdUbp3jZP9iVx68y
ZtHbhpnZle3bmVFBkgsF8vHWsMlxMZzr2PpAl02VXrrE6z0ScTz+GmVU2V89Y5nv
kn9DhAR4gcyKbKKgRtwjCLMoCfxsdaHTOJXfcHhsiqQP4PwdFkV6bQAymwcJegY/
ze5wKX8XqIML6yUCnhrN41pjt6NkIQoyRneLwX5ymeRLfWg23i9YOVU4Njmm9X52
kH7Xg0UuT6HTyyNER7iqwh61gQ33ETkfWd9UrHFGi7q70UJAr+cVXtzJjqnh08OU
BExph/lQfxXuivpiThvjZkPvMVqISyCrsIAXrwjhXnjqwz/3nt3i6zrfvPNNPG0=
=VdKf
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/stefanha/tags/net-pull-request' into staging
# gpg: Signature made Fri Jun 12 13:57:20 2015 BST using RSA key ID 81AB73C8
# gpg: Good signature from "Stefan Hajnoczi <stefanha@redhat.com>"
# gpg: aka "Stefan Hajnoczi <stefanha@gmail.com>"
* remotes/stefanha/tags/net-pull-request:
qmp/hmp: add rocker device support
rocker: bring link up/down on PHY enable/disable
rocker: update tests using hw-derived interface names
rocker: Add support for phys name
iohandler: Change return type of qemu_set_fd_handler to "void"
event-notifier: Always return 0 for posix implementation
xen_backend: Remove unused error handling of qemu_set_fd_handler
oss: Remove unused error handling of qemu_set_fd_handler
alsaaudio: Remove unused error handling of qemu_set_fd_handler
main-loop: Drop qemu_set_fd_handler2
Change qemu_set_fd_handler2(..., NULL, ...) to qemu_set_fd_handler
tap: Drop tap_can_send
net/socket: Drop net_socket_can_send
netmap: Drop netmap_can_send
l2tpv3: Drop l2tpv3_can_send
stubs: Add qemu_set_fd_handler
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Michael R. Hines <mrhines@us.ibm.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
RDMA has two data types that are named confusingly;
RDMALocalBlock (pointed to indirectly by local_ram_blocks)
RDMARemoteBlock (pointed to by block in RDMAContext)
RDMALocalBlocks, as the name suggests is a data strucuture that
represents the RDMAable RAM Blocks on the current side of the migration
whichever that is.
RDMARemoteBlocks is always the shape of the RAMBlocks on the
destination, even on the destination.
Rename:
RDMARemoteBlock -> RDMADestBlock
context->'block' -> context->dest_blocks
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Michael R. Hines <mrhines@us.ibm.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Badly formatted migration streams can go undetected or produce
misleading errors due to a lock of checking at the end of sections.
In particular a section that adds an extra 0x00 at the end
causes what looks like a normal end of stream and thus doesn't produce
any errors, and something that ends in a 0x01..0x04 kind of look
like real section headers and then fail when the section parser tries
to figure out which section they are. This is made worse by the
choice of 0x00..0x04 being small numbers that are particularly common
in normal section data.
This patch adds a section footer consisting of a marker (0x7e - ~)
followed by the section-id that was also sent in the header. If
they mismatch then it throws an error explaining which section was
being loaded.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
The next patch adds section footers; but we don't want to
break migration compatibility so disable them on older
machine types
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
The header writing for device sections is open coded in
a few places, merge it into one.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
In postcopy we need the loadvm_handlers to be used in a couple
of different instances of the loadvm loop/routine, and thus
it can't be local any more.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
qemu_peek_buffer currently copies the data it reads into a buffer,
however a future patch wants access to the buffer without the copy,
hence rework to remove the copy to the layer above.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
There are currently lots of pieces of incoming migration state scattered
around, and postcopy is adding more, and it seems better to try and keep
it together.
allocate MIS in process_incoming_migration_co
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
check the return value of the function it calls and error if it's non-0
Fixup qemu_rdma_init_one_block that is the only current caller,
and rdma_add_block the only function it calls using it.
Pass the name of the ramblock to the function; helps in debugging.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Reviewed-by: Michael R. Hines <mrhines@us.ibm.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Split qemu_savevm_state_begin to:
qemu_savevm_state_header That writes the initial file header.
qemu_savevm_state_begin That sets up devices and does the first
device pass.
Used later in postcopy.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
and use it in loadvm_state and ram_load.
Where ever it's used, check the return and error if it failed.
Minor: ram_load was using a 257 byte array for its string, the
maximum length is 255 bytes + 0 terminator, so fix to 256
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
We create optional sections with this patch. But we already have
optional subsections. Instead of having two mechanism that do the
same, we can just generalize it.
For subsections we just change:
- Add a needed function to VMStateDescription
- Remove VMStateSubsection (after removal of the needed function
it is just a VMStateDescription)
- Adjust the whole tree, moving the needed function to the corresponding
VMStateDescription
Signed-off-by: Juan Quintela <quintela@redhat.com>
This way, we will put savevm global state here, instead of lots of variables.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
We assign the MIGRATION_STATUS_SETUP status in two places. Just in
succession. Just remove the second one.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Qemu crashes when IPv6 address is specified for migration and access
to any RDMA uverbs device available on the system is blocked using cgroups.
Fix the crash by checking the return value of ibv_open_device routine.
Signed-off-by: Meghana Cheripady <meghana.cheripady@avagotech.com>
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@avagotech.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
There are two places that define 'len' variable, It's OK for compiling,
but makes it difficult for reading.
Remove the local one which defined in the inside 'while' loop.
Signed-off-by: zhanghailiang <zhang.zhanghailiang@huawei.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
To make changes easier, with the copy, I maintained almost all include
files. Now I remove the unnecessary ones on this patch. This compiles
on linux x64 with all architectures configured, and cross-compiles for
windows 32 and 64 bits.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
If anyone feels like adding himself to the list, just sent me a patch.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
For historic reasons, ram migration have been on arch_init.c. Just
split it into migration/ram.c, the same that happened with block.c.
There is only code movement, no changes altogether.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Add the qmp commands to tune and query the parameters used in live
migration.
Signed-off-by: Liang Li <liang.z.li@intel.com>
Signed-off-by: Yang Zhang <yang.z.zhang@intel.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Put the three parameters related to multiple thread (de)compression
into an int array, and use an enum type to index the parameter.
Signed-off-by: Liang Li <liang.z.li@intel.com>
Signed-off-by: Yang Zhang <yang.z.zhang@intel.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
The multiple compression threads can be turned on/off through
qmp and hmp interface before doing live migration.
Signed-off-by: Liang Li <liang.z.li@intel.com>
Signed-off-by: Yang Zhang <yang.z.zhang@intel.com>
Reviewed-by: Dr.David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
qemu_put_compression_data() compress the data and put it to QEMUFile.
qemu_put_qemu_file() put the data in the buffer of source QEMUFile to
destination QEMUFile.
Signed-off-by: Liang Li <liang.z.li@intel.com>
Signed-off-by: Yang Zhang <yang.z.zhang@intel.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Add the code to create and destroy the multiple threads those will be
used to do data decompression. Left some functions empty just to keep
clearness, and the code will be added later.
Signed-off-by: Liang Li <liang.z.li@intel.com>
Signed-off-by: Yang Zhang <yang.z.zhang@intel.com>
Reviewed-by: Dr.David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Add the code to create and destroy the multiple threads those will
be used to do data compression. Left some functions empty to keep
clearness, and the code will be added later.
Signed-off-by: Liang Li <liang.z.li@intel.com>
Signed-off-by: Yang Zhang <yang.z.zhang@intel.com>
Reviewed-by: Dr.David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
We often don't need the BlockDriverState for functions
that operate on bitmaps. Remove it.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1429314609-29776-15-git-send-email-jsnow@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This field will be set for user created dirty bitmap. Also pass in an
error pointer to bdrv_create_dirty_bitmap, so when a name is already
taken on this BDS, it can report an error message. This is not global
check, two BDSes can have dirty bitmap with a common name.
Implemented bdrv_find_dirty_bitmap to find a dirty bitmap by name, will
be used later when other QMP commands want to reference dirty bitmap by
name.
Add bdrv_dirty_bitmap_make_anon. This unsets the name of dirty bitmap.
Signed-off-by: Fam Zheng <famz@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1429314609-29776-3-git-send-email-jsnow@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
As part of commit e325b49a32,
order in which resources are destroyed was changed for fixing
a seg fault. Due to this change, CQ will never get destroyed as
CQ should be destroyed after QP destruction. Seg fault is caused
improper cleanup when connection fails. Fixing cleanup after
connection failure and order in which resources are destroyed
in qemu_rdma_cleanup() routine.
Signed-off-by: Meghana Cheripady <meghana.cheripady@emulex.com>
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
'cancelling' status was introduced by commit 51cf4c1a, mainly to avoid a
possible start of a new migration process while the previous one still exists.
But we didn't expose this status to user, instead we returned the 'active' state.
Here, we expose it to the user (such as libvirt), 'cancelling' status only
occurs for a short window before the migration aborts, so for users,
if they cancel a migration process, it will observe 'cancelling' status
occasionally.
Testing revealed that with older libvirt (anything 1.2.13 or less) will
print an odd error message if the state is seen, but that the migration
is still properly cancelled. Newer libvirt will be patched to recognize
the new state without the odd error message.
Signed-off-by: zhanghailiang <zhang.zhanghailiang@huawei.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Cc: libvir-list@redhat.com
Signed-off-by: Juan Quintela <quintela@redhat.com>
The original 'status' is an open-coded 'str' type, convert it to use an
enum type.
This conversion is backwards compatible, better documented and
more convenient for future extensibility.
In addition, Fix a typo for qapi-schema.json (just remove the typo) :
s/'completed'. 'comppleted' (since 1.2)/'completed' (since 1.2)
Signed-off-by: zhanghailiang <zhang.zhanghailiang@huawei.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Rename all macro MIG_STATE_* to MIGRATION_STATUS_* except "MIG_STATE_ERROR",
we rename it to "MIGRATION_STATUS_FAILED" which will match the migration status
string 'failed'.
Signed-off-by: zhanghailiang <zhang.zhanghailiang@huawei.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
migrate_rdma_pin_all() and qsb_clone() are completely unused and thus
can be deleted.
Signed-off-by: Thomas Huth <thuth@linux.vnet.ibm.com>
Cc: Juan Quintela <quintela@redhat.com>
Cc: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Create a separate error for the case where migrate_incoming is
used after a succesful migrate_incoming.
Reword the error in the case where '-incoming defer' is missing
to omit the command name so it's right for both hmp and qmp.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Fix type casts between pointers and 64 bit integers.
Now 32 bit builds are possible again.
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Signed-off-by: Juan Quintela <quintela@redhat.com>
The current code won't compile on 32 bit hosts because there are lots
of type casts between pointers and 64 bit integers.
Fix some of them.
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Do not check for rdma->host being empty twice. This removes a large
"if" block, so code indentation is changed. While at it, remove an
ugly goto from the loop, replacing it with a cleaner if logic. And
finally, there's no need to initialize `ret' variable since is always
has a value.
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Tested-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
--
fixed space detected by Dave
Signed-off-by: Juan Quintela <quintela@redhat.com>
qerror_report_err() is a transitional interface to help with
converting existing monitor commands to QMP. It should not be used
elsewhere. Replace by error_report_err() in
process_incoming_migration_co().
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
It used to be an int, but then we can't pass directly the
bytes_transferred parameter, that would happen later in the series.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Add migrate_incoming/migrate-incoming to start an incoming
migration.
Once a qemu has been started with
-incoming defer
the migration can be started by issuing:
migrate_incoming uri
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
-incoming defer causes qemu to wait for an incoming migration
to be specified later. The monitor can be used to set migration
capabilities that may affect the incoming connection process.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
* Remove trailing whitespace (fixes 9 errors from checkpatch.pl).
One comment line was longer than 80 characters, so wrap it
and fix a typo, too.
* Replace tabs by blanks (fixes 1 error).
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
It looks like the dtrace trace code gets upset if you have trace names
with __ in, which the migration/rdma.c code does.
Rename the functions and the associated traces.
Fixes: 733252deb8
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reported-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Tested-by: Andreas Färber <afaerber@suse.de>
Message-id: 1424105885-12149-1-git-send-email-dgilbert@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Warnings from the Sparse static analysis tool:
migration-rdma.c:151:12: warning:
symbol 'wrid_desc' was not declared. Should it be static?
migration-rdma.c:190:12: warning:
symbol 'control_desc' was not declared. Should it be static?
migration-rdma.c:3301:19: warning:
symbol 'rdma_read_ops' was not declared. Should it be static?
migration-rdma.c:3308:19: warning:
symbol 'rdma_write_ops' was not declared. Should it be static?
Cc: Juan Quintela <quintela@redhat.com>
Cc: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Gonglei <arei.gonglei@huawei.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Turn all the D/DD/DDDPRINTFs into trace events
Turn most of the fprintf(stderr, into error_report
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
One of the annoyances of the current migration format is the fact that
it's not self-describing. In fact, it's not properly describing at all.
Some code randomly scattered throughout QEMU elaborates roughly how to
read and write a stream of bytes.
We discussed an idea during KVM Forum 2013 to add a JSON description of
the migration protocol itself to the migration stream. This patch
adds a section after the VM_END migration end marker that contains
description data on what the device sections of the stream are composed of.
This approach is backwards compatible with any QEMU version reading the
stream, because QEMU just stops reading after the VM_END marker and ignores
any data following it.
With an additional external program this allows us to decipher the
contents of any migration stream and hopefully make migration bugs easier
to track down.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
For ftell we flush the output buffer to ensure that we don't have anything
lingering in our internal buffers. This is a very safe thing to do.
However, with the dynamic size measurement that the dynamic vmstate
description will bring this would turn out quite slow.
Instead, we can fast path this specific measurement and just take the
internal buffers into account when telling the kernel our position.
I'm sure I overlooked some corner cases where this doesn't work, so
instead of tuning the safe, existing version, this patch adds a fast
variant of ftell that gets used by the dynamic vmstate description code
which isn't critical when it fails.
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Mostly on the load side, so that when we get a complaint about
a migration failure we can figure out what it didn't like.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Convert a bunch of fprintfs to error_reports
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Force shutdown on migration socket on cancel to cause the cancel
to complete even if the socket is blocked on a dead network.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
libvirt prefers opening the TCP connection itself, for two reasons.
First, connection failed errors can be detected easier, without having
to parse qemu's error output.
Second, libvirt might be asked to secure the transfer by tunnelling the
communication through an TLS layer.
Therefore, libvirt opens the TCP connection itself and passes an FD to qemu
using QMP and a POSIX-specific mechanism.
Hence, in order to make the reverse-path work in such cases, qemu needs to
distinguish if the transmitted FD is a socket (reverse-path available)
or not (reverse-path might not be available) and use the corresponding
abstraction.
Signed-off-by: Cristian Klein <cristian.klein@cs.umu.se>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Add QEMUFile interface to allow a socket to be 'shut down' - i.e. any
reads/writes will fail (and any blocking read/write will be woken).
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Only free qsb that qemu_bufopen allocated, and also allow
qemu_bufopen accept qsb as input for write operation. It
will make the API more logical:
1.If you create the QEMUSizedBuffer yourself, you need to
free it by using qsb_free() but not depends on other API
like qemu_fclose.
2.allow qemu_bufopen() accept QEMUSizedBuffer as input for
write operation, otherwise, it will be a little strange
for this API won't accept the second parameter.
This brings API change, since there are only 3
users of this API currently, this change only impact the
first one which will be fixed in patch 2 of this patchset,
so I think it is safe to do this change.
1 70 tests/test-vmstate.c <<open_mem_file_read>>
return qemu_bufopen("r", qsb);
2 404 tests/test-vmstate.c <<test_save_noskip>>
QEMUFile *fsave = qemu_bufopen("w", NULL);
3 424 tests/test-vmstate.c <<test_save_skip>>
QEMUFile *fsave = qemu_bufopen("w", NULL);
Signed-off-by: Yang Hongyang <yanghy@cn.fujitsu.com>
Cc: Dr. David Alan Gilbert <dgilbert@redhat.com>
Cc: Juan Quintela <quintela@redhat.com>
Cc: Amit Shah <amit.shah@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Add a cast in qemu_get_be32() to avoid shifting left into the sign
bit of a signed integer (which is undefined behaviour in C).
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Because of wrong return value of .save_live_pending() in
migration/block.c, migration finishes before the whole disk is
transferred. Such situation occurs when the migration process is fast
enough, for example when source and dest are on the same host.
If in the bulk phase we return something < max_size, we will skip
transferring the tail of the device. Currently we have "set pending to
BLOCK_SIZE if it is zero" for bulk phase, but there no guarantee, that
it will be < max_size.
True approach is to return, for example, max_size+1 when we are in the
bulk phase.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@parallels.com>
Message-id: 1419933856-4018-2-git-send-email-vsementsov@parallels.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Mirror and migration use dirty bitmaps for their purposes, and since
commit [block: per caller dirty bitmap] they use their own bitmaps, not
the global one. But they use old functions bdrv_set_dirty and
bdrv_reset_dirty, which change all dirty bitmaps.
Named dirty bitmaps series by Fam and Snow are affected: mirroring and
migration will spoil all (not related to this mirroring or migration)
named dirty bitmaps.
This patch fixes this by adding bdrv_set_dirty_bitmap and
bdrv_reset_dirty_bitmap, which change concrete bitmap. Also, to prevent
such mistakes in future, old functions bdrv_(set,reset)_dirty are made
static, for internal block usage.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@parallels.com>
CC: John Snow <jsnow@redhat.com>
CC: Fam Zheng <famz@redhat.com>
CC: Denis V. Lunev <den@openvz.org>
CC: Stefan Hajnoczi <stefanha@redhat.com>
CC: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Message-id: 1417081246-3593-1-git-send-email-vsementsov@parallels.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
The splitting of qemu-file and addition of the buffered file landed
at the same time; so now split the buffered file code out.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Now we've got multiple QEMUFile source files, some of them need
access to things that were defined in qemu-file.c, so create
a -internal header for them.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
The general feeling is that having migration/migration-blah
is overkill.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
The migration code now occupies a fair chunk of the top level .c
files, it seems time to give it it's own directory.
I've not touched:
arch_init.c - that's mostly RAM migration but has a few random other
bits
savevm.c - because it's built target specific
This is purely a code move; no code has changed.
- it fails checkpatch because of old violations, it feels safer
to keep this as purely a move and fix those at some mythical future
date.
The xbzrle and vmstate tests are now only run for softmmu builds
since they require files in the migrate/ directory which is only built
for softmmu.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
