This adds the BCM2835 SDHost controller from Arasan.
Signed-off-by: Clement Deschamps <clement.deschamps@antfield.fr>
Message-id: 20170224164021.9066-2-clement.deschamps@antfield.fr
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This quirk is a workaround for the following hardware behaviour, on
which UEFI (specifically, the bootloader for Windows on Pi2) depends:
1. at boot with an SD card present, the interrupt status/enable
registers are initially zero
2. upon enabling it in the interrupt enable register, the card insert
bit in the interrupt status register is immediately set
3. after a subsequent controller reset, the card insert interrupt does
not fire, even if enabled in the interrupt enable register
Signed-off-by: Andrew Baumann <Andrew.Baumann@microsoft.com>
Message-id: 1456436130-7048-3-git-send-email-Andrew.Baumann@microsoft.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This reverts commit 723697551a.
This change was poorly tested on my part. It squelched card insertion
interrupts on reset, but that was not necessary because sdhci_reset()
clears all the registers (via the call to memset), so the subsequent
sdhci_insert_eject_cb() call never sees the card insert interrupt
enabled. However, not calling the insert_eject_cb results in prnsts
remaining 0, when it actually needs to be updated to indicate card
presence and R/O status.
Signed-off-by: Andrew Baumann <Andrew.Baumann@microsoft.com>
Message-id: 1456436130-7048-2-git-send-email-Andrew.Baumann@microsoft.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Update the SDHCI code to use the new SDBus APIs.
This commit introduces the new command line options required
to connect a disk to sdhci-pci:
-device sdhci-pci -drive id=mydrive,[...] -device sd,drive=mydrive
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 1455646193-13238-6-git-send-email-peter.maydell@linaro.org
Add a QOM bus for SD cards to plug in to.
Note that since sd_enable() is used only by one board and there
only as part of a broken implementation, we do not provide it in
the SDBus API (but instead add a warning comment about the old
function). Whoever converts OMAP and the nseries boards to QOM
will need to either implement the card switch properly or move
the enable hack into the OMAP MMC controller model.
In the SDBus API, the old-style use of sd_set_cb to register some
qemu_irqs for notification of card insertion and write-protect
toggling is replaced with methods in the SDBusClass which the
card calls on status changes and methods in the SDClass which
the controller can call to find out the current status. The
query methods will allow us to remove the abuse of the 'register
irqs' API by controllers in their reset methods to trigger
the card to tell them about the current status again.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 1455646193-13238-5-git-send-email-peter.maydell@linaro.org
Turn the SD card into a QOM device.
This conversion only changes the device itself; the various
functions which are effectively methods on the device are not
touched at this point.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 1455646193-13238-3-git-send-email-peter.maydell@linaro.org
This is needed for a quirk of the Raspberry Pi (bcm2835/6) MMC
controller, where the card insert bit is documented as unimplemented
(always reads zero, doesn't generate interrupts) but is in fact
observed on hardware as set at power on, but is cleared (and remains
clear) on subsequent controller resets.
Signed-off-by: Andrew Baumann <Andrew.Baumann@microsoft.com>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Message-id: 1450738069-18664-4-git-send-email-Andrew.Baumann@microsoft.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
We currently fuse controller and card into a single device model, but
we intend qomify things properly and separate the two. The properties
that really belong to the card would then have to somehow pass-through
to the card's properties. To avoid that complication, either mark
them experimental or drop them.
Properties "capareg", "maxcurr" and the usual PCI device properties
belong to the controller. Property "drive" belongs to the card;
rename it to "x-drive". Properties "logical_block_size",
"physical_block_size", "min_io_size", "opt_io_size",
"discard_granularity" belong to the card, but have no effect; drop
them.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1449503710-3707-2-git-send-email-armbru@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Split sdhci.h into pubilc version (i.e include/hw/sd/sdhci.h) and
internal version (i.e hw/sd/sdhci-interna.h) based on register
declarations and object declaration.
Signed-off-by: Sai Pavan Boddu <saipava@xilinx.com>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Create a sd directory under include/hw/ and move sd.h to
include/hw/sd/
Signed-off-by: Sai Pavan Boddu <saipava@xilinx.com>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
