pci_bus_is_root() currently relies on a method in the PCIBusClass.
But it's always known if a PCI bus is a root bus when we create it, so
using a dynamic method is overkill.
This replaces it with an IS_ROOT bit in a new flags field, which is set on
root buses and otherwise clear. As a bonus this removes the special
is_root logic from pci_expander_bridge, since it already creates its bus
as a root bus.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Message-Id: <20190424041959.4087-3-david@gibson.dropbear.id.au>
For devices that require msi_init/msix_init to succeed, add a
dependency on CONFIG_MSI_NONBROKEN. This will prevent those devices
from appearing in a binary that cannot instantiate them.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Claim ACS support in the generic PCIe root port to allow
passthrough of individual functions of a device to different
guests (in a nested virt.setting) with VFIO.
Without this patch, all functions of a device, such as all VFs of
an SR/IOV device, will end up in the same IOMMU group.
A similar situation occurs on Windows with Hyper-V.
In the single function device case, it also has a small cosmetic
benefit in that the root port itself is not grouped with
the device. VFIO handles that situation in that binding rules
only apply to endpoints, so it does not limit passthrough in
those cases.
Signed-off-by: Knut Omang <knut.omang@oracle.com>
Reviewed-by: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Message-Id: <319460b483f566dd57487eb3dd340ed4c10aa53c.1550768238.git-series.knut.omang@oracle.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
%-softmmu.mak only keep boards definitions in Kconfig mode.
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Message-Id: <20190123065618.3520-43-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Instead of including the same list of devices for each target,
set CONFIG_PCI to true, and make the devices default to present
whenever PCI is available. However, s390x does not want all the
PCI devices, so there is a separate symbol to enable them.
Done mostly with the following script:
while read i; do
i=${i%=y}; i=${i#CONFIG_}
sed -i -e'/^config '$i'$/!b' -en \
-e'a\' -e' default y if PCI_DEVICES\' -e' depends on PCI' \
`grep -lw $i hw/*/Kconfig`
done < default-configs/pci.mak
followed by replacing a few "depends on" clauses with "select"
whenever the symbol is not really related to PCI.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190123065618.3520-31-yang.zhong@intel.com>
Acked-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The Kconfig files were generated mostly with this script:
for i in `grep -ho CONFIG_[A-Z0-9_]* default-configs/* | sort -u`; do
set fnord `git grep -lw $i -- 'hw/*/Makefile.objs' `
shift
if test $# = 1; then
cat >> $(dirname $1)/Kconfig << EOF
config ${i#CONFIG_}
bool
EOF
git add $(dirname $1)/Kconfig
else
echo $i $*
fi
done
sed -i '$d' hw/*/Kconfig
for i in hw/*; do
if test -d $i && ! test -f $i/Kconfig; then
touch $i/Kconfig
git add $i/Kconfig
fi
done
Whenever a symbol is referenced from multiple subdirectories, the
script prints the list of directories that reference the symbol.
These symbols have to be added manually to the Kconfig files.
Kconfig.host and hw/Kconfig were created manually.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Message-Id: <20190123065618.3520-27-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Introduce and use the "unplug" callback.
This is a preparation for multi-stage hotplug handlers, whereby the bus
hotplug handler is overwritten by the machine hotplug handler. This handler
will then pass control to the bus hotplug handler. So to get this running
cleanly, we also have to make sure to go via the hotplug handler chain when
actually unplugging a device after an unplug request. Lookup the hotplug
handler and call "unplug".
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
These functions are essentially the same, we only have to use
object_get_typename() for reporting errors. So let's share the
implementation of hotplug handler callbacks.
Suggested-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The callbacks are also called for cold plugged devices. Drop the "hot"
to better match the actual callback names.
While at it, also rename shpc_device_hotplug_common() to
shpc_device_plug_common().
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Change the default speed and width for new machine types to the
fastest and widest currently supported. This should be compatible to
the PCIe 4.0 spec. Pre-QEMU-4.0 machine types remain at 2.5GT/s, x1
width.
Cc: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Allow users to experimentally specify speed and width values for the
generic PCIe root port. Defaults remain at 2.5GT/s & x1 for
compatiblity with the intent to only support changing defaults via
machine types for now.
Note for libvirt testing that pcie-root-port controllers are given
default names like "pci.7" which don't play well with using the
"-set device.$name.$prop=$value" options accessible to us via
<qemu:commandline> options. The solution is to add an <alias> to the
pcie-root-port <controller>, for example:
<controller type='pci' index='7' model='pcie-root-port'>
<model name='pcie-root-port'/>
<target chassis='7' port='0x15'/>
<alias name='ua-gfx0'/>
<address type='pci' domain='0x0000' bus='0x00' slot='0x02' function='0x5'/>
</controller>
The "ua-" here is a mandatory prefix. We can then use:
<qemu:commandline>
<qemu:arg value='-set'/>
<qemu:arg value='device.ua-gfx0.x-speed=8'/>
<qemu:arg value='-set'/>
<qemu:arg value='device.ua-gfx0.x-width=16'/>
</qemu:commandline>
or, without an alias, set globals such as:
<qemu:commandline>
<qemu:arg value='-global'/>
<qemu:arg value='pcie-root-port.x-speed=8'/>
<qemu:arg value='-global'/>
<qemu:arg value='pcie-root-port.x-width=16'/>
</qemu:commandline>
Cc: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Tested-by: Geoffrey McRae <geoff@hostfission.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add fields allowing the PCIe link speed and width of a PCIESlot to
be configured, with an instance_post_init callback on the root port
parent class to set defaults. This allows child classes to set these
via properties or via their own instance_init callback, without
requiring all implementions to support arbitrary user selected values.
Cc: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Tested-by: Geoffrey McRae <geoff@hostfission.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Introduced in 48ebf2f90f and faf1e708d5, these functions
were never used. Remove them.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add hint to firmware (e.g. SeaBIOS) to reserve addtional
BUS/IO/MEM/PREF resource for legacy pci-pci bridge. Add the
resource reserve capability deleting in pci_bridge_dev_exitfn.
Signed-off-by: Jing Liu <jing2.liu@linux.intel.com>
Reviewed-by: Marcel Apfelbaum<marcel.apfelbaum@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Factor "bus_reserve", "io_reserve", "mem_reserve", "pref32_reserve"
and "pref64_reserve" fields of the "GenPCIERootPort" structure out
to "PCIResReserve" structure, so that other PCI bridges can
reuse it to add resource reserve capability.
Signed-off-by: Jing Liu <jing2.liu@linux.intel.com>
Reviewed-by: Marcel Apfelbaum<marcel.apfelbaum@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
- new stats in virtio balloon
- virtio eventfd rework for boot speedup
- vhost memory rework for boot speedup
- fixes and cleanups all over the place
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJagxKDAAoJECgfDbjSjVRp5qAH/3gmgBaIzL3KRHd5i0RZifJv
PvyAVYgZd7h0+/1r9GM7guHKyEPZ08JtbHSm/HuDV4BD/Vf3/8joy8roExIfde2A
6k8fd6ANVQmE3t5zUxNXi9qiG4pO4xDIu4cMAbixzgN9x5ttlcfTw7fTT0e0VJxJ
8SN02/uCPPR/DY4/cpjah+slSyv6rBKT1v1ONy7djyRTYHi6h3Meoh05YfEALkwA
goxTKBZHi0L1IZ3HP/ZpXJDohQ5n2P09DX0fQgb8PgmW6WIWB/Qpi5pD53LZpMCV
n9waTF0U0ahneFd2FHo22QMMrwWvQyrjv+w5uXVr+qmHb/OyH2tUt7PgGF9+QKA=
=78s5
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
virtio,vhost,pci,pc: features, fixes and cleanups
- new stats in virtio balloon
- virtio eventfd rework for boot speedup
- vhost memory rework for boot speedup
- fixes and cleanups all over the place
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Tue 13 Feb 2018 16:29:55 GMT
# gpg: using RSA key 281F0DB8D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>"
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>"
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* remotes/mst/tags/for_upstream: (22 commits)
virtio-balloon: include statistics of disk/file caches
acpi-test: update FADT
lpc: drop pcie host dependency
tests: acpi: fix FADT not being compared to reference table
hw/pci-bridge: fix pcie root port's IO hints capability
libvhost-user: Support across-memory-boundary access
libvhost-user: Fix resource leak
virtio-balloon: unref the memory region before continuing
pci: removed the is_express field since a uniform interface was inserted
virtio-blk: enable multiple vectors when using multiple I/O queues
pci/bus: let it has higher migration priority
pci-bridge/i82801b11: clear bridge registers on platform reset
vhost: Move log_dirty check
vhost: Merge and delete unused callbacks
vhost: Clean out old vhost_set_memory and friends
vhost: Regenerate region list from changed sections list
vhost: Merge sections added to temporary list
vhost: Simplify ring verification checks
vhost: Build temporary section list and deref after commit
virtio: improve virtio devices initialization time
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This cleanup makes the number of objects depending on qapi/error.h
drop from 1910 (out of 4743) to 1612 in my "build everything" tree.
While there, separate #include from file comment with a blank line,
and drop a useless comment on why qemu/osdep.h is included first.
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20180201111846.21846-5-armbru@redhat.com>
[Semantic conflict with commit 34e304e975 resolved, OSX breakage fixed]
according to Eduardo Habkost's commit fd3b02c889 all PCIEs now implement
INTERFACE_PCIE_DEVICE so we don't need is_express field anymore.
Devices that implements only INTERFACE_PCIE_DEVICE (is_express == 1)
or
devices that implements only INTERFACE_CONVENTIONAL_PCI_DEVICE (is_express == 0)
where not affected by the change.
The only devices that were affected are those that are hybrid and also
had (is_express == 1) - therefor only:
- hw/vfio/pci.c
- hw/usb/hcd-xhci.c
- hw/xen/xen_pt.c
For those 3 I made sure that QEMU_PCI_CAP_EXPRESS is on in instance_init()
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Yoni Bettan <ybettan@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
In the past, we prioritized IOMMU migration so that we have such a
priority order:
IOMMU > PCI Devices
When migrating a guest with both vIOMMU and a pcie-root-port, we'll
always migrate vIOMMU first, since pci buses will be seen to have the
same priority of general PCI devices.
That's problematic.
The thing is that PCI bus number information is stored in the root port,
and that is needed by vIOMMU during post_load(), e.g., to figure out
context entry for a device. If we don't have correct bus numbers for
devices, we won't be able to recover device state of the DMAR memory
regions, and things will be messed up.
So let's boost the PCIe root ports to be even with higher priority:
PCIe Root Port > IOMMU > PCI Devices
A smoke test shows that this patch fixes bug 1538953.
Also, apply this rule to all the PCI bus/bridge devices: ioh3420,
xio3130_downstream, xio3130_upstream, pcie_pci_bridge, pci-pci bridge,
i82801b11.
I noted that we set pcie_pci_bridge_dev_vmstate twice. Clean that up
together.
CC: Alex Williamson <alex.williamson@redhat.com>
CC: Marcel Apfelbaum <marcel@redhat.com>
CC: Michael S. Tsirkin <mst@redhat.com>
CC: Dr. David Alan Gilbert <dgilbert@redhat.com>
CC: Juan Quintela <quintela@redhat.com>
CC: Laurent Vivier <lvivier@redhat.com>
Bug: https://bugzilla.redhat.com/show_bug.cgi?id=1538953
Reported-by: Maxime Coquelin <maxime.coquelin@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The "i82801b11-bridge" device model is a descendant of "base-pci-bridge"
(TYPE_PCI_BRIDGE). However, unlike other similar devices, such as
- pci-bridge,
- pcie-pci-bridge,
- PCIE Root Port,
- xio3130 switch upstream and downstream ports,
- dec-21154-p2p-bridge,
- pbm-bridge,
- xilinx-pcie-root,
"i82801b11-bridge" does not clear the bridge specific registers at
platform reset.
This is a problem because devices on "i82801b11-bridge" continue to
respond to config space cycles after platform reset, when addressed with
the bus number that was previously programmed into the secondary bus
number register of "i82801b11-bridge". This error breaks OVMF's search for
extra (PXB) root buses, for example.
The device class reset method for "i82801b11-bridge" is currently NULL;
set it directly to pci_bridge_reset(), like the last three bridge models
in the above listing do.
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Marcel Apfelbaum <marcel@redhat.com>
Cc: qemu-stable@nongnu.org
Ref: https://bugzilla.redhat.com/show_bug.cgi?id=1541839
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Here we rename PBMPCIBridge to SimbaPCIBridge and the QOM type from
TYPE_PBM_PCI_BRIDGE to TYPE_SIMBA_PCI_BRIDGE in improve the clarity
of the device name.
Also touch up the relevant spots in apb.c and various other function
names as appropriate.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Artyom Tarasenko <atar4qemu@gmail.com>
Move the QOM type and macros into a new include/hw/pci-bridge/simba.h
file, and add a new CONFIG_SIMBA Makefile.objs variable which is enabled
for sparc64-softmmu builds only.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
CC: Michael S. Tsirkin <mst@redhat.com>
CC: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Artyom Tarasenko <atar4qemu@gmail.com>
If we try to use more pcie_root_ports then available slots
and an IO hint is passed to the port, QEMU crashes because
we try to init the "IO hint" capability even if the device
is not created.
Fix it by checking for error before adding the capability,
so QEMU can fail gracefully.
Signed-off-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Anthony PERARD <anthony.perard@citrix.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The bus pointer in PCIDevice is basically redundant with QOM information.
It's always initialized to the qdev_get_parent_bus(), the only difference
is the type.
Therefore this patch eliminates the field, instead creating a pci_get_bus()
helper to do the type mangling to derive it conveniently from the QOM
Device object underneath.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
pci_bus_init(), pci_bus_new_inplace(), pci_bus_new() and pci_register_bus()
are misleadingly named. They're not used for initializing *any* PCI bus,
but only for a root PCI bus.
Non-root buses - i.e. ones under a logical PCI to PCI bridge - are instead
created with a direct qbus_create_inplace() (see pci_bridge_initfn()).
This patch renames the functions to make it clear they're only used for
a root bus.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
The PCIE-PCI bridge is specific to "pure" PCIe systems
(on QEMU we have X86 and ARM), it does not make sense to
have it in other archs.
Reported-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Yongbok Kim <yongbok.kim@mips.com>
IO_LIMIT and IO_BASE registers should not be writable if
gen_pcie_root_port's io-reserve property is set to 0.
The COMMAND register should have the IO flag read only.
Signed-off-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add INTERFACE_CONVENTIONAL_PCI_DEVICE to all direct subtypes of
TYPE_PCI_DEVICE, except:
1) The ones that already have INTERFACE_PCIE_DEVICE set:
* base-xhci
* e1000e
* nvme
* pvscsi
* vfio-pci
* virtio-pci
* vmxnet3
2) base-pci-bridge
Not all PCI bridges are Conventional PCI devices, so
INTERFACE_CONVENTIONAL_PCI_DEVICE is added only to the subtypes
that are actually Conventional PCI:
* dec-21154-p2p-bridge
* i82801b11-bridge
* pbm-bridge
* pci-bridge
The direct subtypes of base-pci-bridge not touched by this patch
are:
* xilinx-pcie-root: Already marked as PCIe-only.
* pcie-pci-bridge: Already marked as PCIe-only.
* pcie-port: all non-abstract subtypes of pcie-port are already
marked as PCIe-only devices.
3) megasas-base
Not all megasas devices are Conventional PCI devices, so the
interface names are added to the subclasses registered by
megasas_register_types(), according to information in the
megasas_devices[] array.
"megasas-gen2" already implements INTERFACE_PCIE_DEVICE, so add
INTERFACE_CONVENTIONAL_PCI_DEVICE only to "megasas".
Acked-by: Alberto Garcia <berto@igalia.com>
Acked-by: John Snow <jsnow@redhat.com>
Acked-by: Anthony PERARD <anthony.perard@citrix.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Change all devices that set is_express=1 to implement
INTERFACE_PCIE_DEVICE.
Cc: Keith Busch <keith.busch@intel.com>
Cc: Kevin Wolf <kwolf@redhat.com>
Cc: Max Reitz <mreitz@redhat.com>
Cc: Dmitry Fleytman <dmitry@daynix.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Marcel Apfelbaum <marcel@redhat.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Hannes Reinecke <hare@suse.com>
Cc: qemu-block@nongnu.org
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
QEMU with the pcie-pci-bridge device crashes if the guest board doesn't support MSI,
e.g. 'qemu-system-ppc64 -M prep -device pcie-pci-bridge'.
This is caused by wrong pcie-pci-bridge instantiation error handling. This patch fixes this issue
by falling back to legacy INTx if MSI is not available.
Also set the bridge's 'msi' property default value to 'auto' in order to trigger errors
only when user explicitly set msi=on.
Reported-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Aleksandr Bezzubikov <zuban32s@gmail.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Tested-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
ioh3420_interrupts_init() pass error message to local_err, then
propagate it to errp by error_propagate(), which is not necessary.
So eliminate it and pass errp directly instead of local_err.
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Marcel Apfelbaum <marcel@redhat.com>
Signed-off-by: Mao Zhongyi <maozy.fnst@cn.fujitsu.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
On commit f8cd1b02 ("pci: Convert to realize"), no error_set*()
call was added for the pcie_chassis_add_slot() error case.
pcie_chassis_add_slot() errors get ignored, making QEMU crash
later. e.g.:
$ qemu-system-x86_64 -device ioh3420 -device xio3130-downstream
qemu-system-x86_64: memory.c:2166: memory_region_del_subregion: Assertion `subregion->container == mr' failed.
Aborted (core dumped)
Fix it by reporting the error using error_setg().
Fixes: f8cd1b0201
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
To enable hotplugging of a newly created pcie-pci-bridge,
we need to tell firmware (e.g. SeaBIOS) to reserve
additional buses or IO/MEM/PREF space for pcie-root-port.
Additional bus reservation allows us to hotplug pcie-pci-bridge into this root port.
The number of buses and IO/MEM/PREF space to reserve are provided to the device via
a corresponding property, and to the firmware via new PCI capability.
The properties' default values are -1 to keep default behavior unchanged.
Signed-off-by: Aleksandr Bezzubikov <zuban32s@gmail.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Tested-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Introduce a new PCIExpress-to-PCI Bridge device,
which is a hot-pluggable PCI Express device and
supports devices hot-plug with SHPC.
This device is intended to replace the DMI-to-PCI Bridge.
Signed-off-by: Aleksandr Bezzubikov <zuban32s@gmail.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Tested-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
In order to propagate error message better, convert shpc_init() to
Error also convert the pci_bridge_dev_initfn() to realize.
Cc: mst@redhat.com
Cc: marcel@redhat.com
Cc: armbru@redhat.com
Signed-off-by: Mao Zhongyi <maozy.fnst@cn.fujitsu.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Convert i82801b11, io3130_upstream, io3130_downstream and
pcie_root_port devices to realize.
Cc: mst@redhat.com
Cc: marcel@redhat.com
Cc: armbru@redhat.com
Signed-off-by: Mao Zhongyi <maozy.fnst@cn.fujitsu.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This way the bridge shows up in the correct section of the
"-device help" text.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Add msix state to pcie-root-ports's vmstate
in order to support migration.
Signed-off-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
A bunch of fixes that missed the release.
Most notably we are reverting shpc back to enabled by default state
as guests uses that as an indicator that hotplug is supported
(even though it's unused). Unfortunately we can't fix this
on the stable branch since that would break migration.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJZHMOuAAoJECgfDbjSjVRp/5IH/3kOa7yV3KUi4QVbQV7WwBH3
LK+/jwIz4UhOZn+bS4qi+gjN6aFhNoBNDFmYsRTWKKdLMvZvkRBMDcv8DMIKeAyl
kG/ispv8VI+GY/CRKnqzPm0FSulv8WPRryxkdGzK4oHiMv+4FpFR0v/n9NRHjwTA
XNJ4k33IqBldXyZwwAzP5dT019EMvbn4bNrkLzlcF2w8mTWPf43eX/kIkRX0cAys
5IVTQVGEOwpnyV0jxJDP+aoVMrqv8xl88LLuRpTgWUo0UnxXL5/GZQOCCUN6DQ7M
BOLmyyP9mT9k8iUI+fQsDxAtY7cL9torq+p985nQdH0nxmI3GCoufn9aJG0J9yc=
=d34x
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'mst/tags/for_upstream' into staging
pci, virtio, vhost: fixes
A bunch of fixes that missed the release.
Most notably we are reverting shpc back to enabled by default state
as guests uses that as an indicator that hotplug is supported
(even though it's unused). Unfortunately we can't fix this
on the stable branch since that would break migration.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Wed 17 May 2017 10:42:06 PM BST
# gpg: using RSA key 0x281F0DB8D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>"
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>"
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* mst/tags/for_upstream:
exec: abstract address_space_do_translate()
pci: deassert intx when pci device unrealize
virtio: allow broken device to notify guest
Revert "hw/pci: disable pci-bridge's shpc by default"
acpi-defs: clean up open brace usage
ACPI: don't call acpi_pcihp_device_plug_cb on xen
iommu: Don't crash if machine is not PC_MACHINE
pc: add 2.10 machine type
pc/fwcfg: unbreak migration from qemu-2.5 and qemu-2.6 during firmware boot
libvhost-user: fix crash when rings aren't ready
hw/virtio: fix vhost user fails to startup when MQ
hw/arm/virt: generate 64-bit addressable ACPI objects
hw/acpi-defs: replace leading X with x_ in FADT field names
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
This reverts commit dc0ae76770.
Disabling the shpc controller has an undesired side effect.
The PCI bridge remains with no attached devices at boot time,
and the guest operating systems do not allocate any resources
for it, leaving the bridge unusable. Note that the behaviour
is dictated by the pci bridge specification.
Revert the commit and leave the shpc controller even if is not
actually used by any architecture. Slot 0 remains unusable at boot time.
Keep shpc off for QEMU 2.9 machines.
Signed-off-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
cannot_instantiate_with_device_add_yet was introduced by commit
efec3dd631 to replace no_user. It was
supposed to be a temporary measure.
When it was introduced, we had 54
cannot_instantiate_with_device_add_yet=true lines in the code.
Today (3 years later) this number has not shrunk: we now have
57 cannot_instantiate_with_device_add_yet=true lines. I think it
is safe to say it is not a temporary measure, and we won't see
the flag go away soon.
Instead of a long field name that misleads people to believe it
is temporary, replace it a shorter and less misleading field:
user_creatable.
Except for code comments, changes were generated using the
following Coccinelle patch:
@@
expression DC;
@@
(
-DC->cannot_instantiate_with_device_add_yet = false;
+DC->user_creatable = true;
|
-DC->cannot_instantiate_with_device_add_yet = true;
+DC->user_creatable = false;
)
@@
typedef ObjectClass;
expression dc;
identifier class, data;
@@
static void device_class_init(ObjectClass *class, void *data)
{
...
dc->hotpluggable = true;
+dc->user_creatable = true;
...
}
@@
@@
struct DeviceClass {
...
-bool cannot_instantiate_with_device_add_yet;
+bool user_creatable;
...
}
@@
expression DC;
@@
(
-!DC->cannot_instantiate_with_device_add_yet
+DC->user_creatable
|
-DC->cannot_instantiate_with_device_add_yet
+!DC->user_creatable
)
Cc: Alistair Francis <alistair.francis@xilinx.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Marcel Apfelbaum <marcel@redhat.com>
Cc: Markus Armbruster <armbru@redhat.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Thomas Huth <thuth@redhat.com>
Acked-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Acked-by: Marcel Apfelbaum <marcel@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20170503203604.31462-2-ehabkost@redhat.com>
[ehabkost: kept "TODO remove once we're there" comment]
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
This obsoletes ppc-for-2.9-20170112, which had a MacOS build bug.
This is a long overdue ppc pull request for qemu-2.9. It's been a
long time coming due to some holidays and inconveniently timed
problems with testing. So, there's a lot in here:
* More POWER9 instruction implementations for TCG
* The simpler parts of my CPU compatibility mode cleanup
* This changes behaviour to prefer compatibility modes over
"raW" mode for new machine type versions
* New "40p" machine type which is essentially a modernized and
cleaned up "prep". The intention is that it will replace "prep"
once it has some more testing and polish.
* Add pseries-2.9 machine type
* Implement H_SIGNAL_SYS_RESET hypercall
* Consolidate the two alternate CPU init paths in pseries by
making it always go through CPU core objects to initialize CPU
* A number of bugfixes and cleanups
* Stop the guest timebase when the guest is stopped under KVM.
This makes the guest system clock also stop when paused, which
matches the x86 behaviour.
* Some preliminary cleanups leading towards implementation of the
POWER9 MMU.
There are also some changes not strictly related to ppc code, but for
its benefit:
* Limit the pxi-expander-bridge (PXB) device to x86 guests only
(it's essentially a hack to work around historical x86
limitations)
* Some additions to the 128-bit math in host_utils, necessary for
some of the new instructions.
* Revise a number of qtests and enable them for ppc
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=vLVl
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dgibson/tags/ppc-for-2.9-20170202' into staging
ppc patch queue 2017-02-02
This obsoletes ppc-for-2.9-20170112, which had a MacOS build bug.
This is a long overdue ppc pull request for qemu-2.9. It's been a
long time coming due to some holidays and inconveniently timed
problems with testing. So, there's a lot in here:
* More POWER9 instruction implementations for TCG
* The simpler parts of my CPU compatibility mode cleanup
* This changes behaviour to prefer compatibility modes over
"raW" mode for new machine type versions
* New "40p" machine type which is essentially a modernized and
cleaned up "prep". The intention is that it will replace "prep"
once it has some more testing and polish.
* Add pseries-2.9 machine type
* Implement H_SIGNAL_SYS_RESET hypercall
* Consolidate the two alternate CPU init paths in pseries by
making it always go through CPU core objects to initialize CPU
* A number of bugfixes and cleanups
* Stop the guest timebase when the guest is stopped under KVM.
This makes the guest system clock also stop when paused, which
matches the x86 behaviour.
* Some preliminary cleanups leading towards implementation of the
POWER9 MMU.
There are also some changes not strictly related to ppc code, but for
its benefit:
* Limit the pxi-expander-bridge (PXB) device to x86 guests only
(it's essentially a hack to work around historical x86
limitations)
* Some additions to the 128-bit math in host_utils, necessary for
some of the new instructions.
* Revise a number of qtests and enable them for ppc
# gpg: Signature made Thu 02 Feb 2017 01:40:16 GMT
# gpg: using RSA key 0x6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>"
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>"
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>"
# gpg: aka "David Gibson (kernel.org) <dwg@kernel.org>"
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dgibson/tags/ppc-for-2.9-20170202: (107 commits)
hw/ppc/pnv: Use error_report instead of hw_error if a ROM file can't be found
ppc/kvm: Handle the "family" CPU via alias instead of registering new types
target/ppc/mmu_hash64: Fix incorrect shift value in amr calculation
target/ppc/mmu_hash64: Fix printing unsigned as signed int
tcg/POWER9: NOOP the cp_abort instruction
target/ppc/debug: Print LPCR register value if register exists
target-ppc: Add xststdc[sp, dp, qp] instructions
target-ppc: Add xvtstdc[sp,dp] instructions
target-ppc: Add MMU model check for booke machines
ppc: switch to constants within BUILD_BUG_ON
target/ppc/cpu-models: Fix/remove bad CPU aliases
target/ppc: Remove unused POWERPC_FAMILY(POWER)
spapr: clock should count only if vm is running
ppc: Remove unused function cpu_ppc601_rtc_init()
target/ppc: Add pcr_supported to POWER9 cpu class definition
powerpc/cpu-models: rename ISAv3.00 logical PVR definition
target-ppc: Add xvcv[hpsp, sphp] instructions
target-ppc: Add xsmulqp instruction
target-ppc: Add xsdivqp instruction
target-ppc: Add xscvsdqp and xscvudqp instructions
...
# Conflicts:
# hw/pci-bridge/Makefile.objs
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The shpc component is optional while ACPI hotplug is used
for hot-plugging PCI devices into a PCI-PCI bridge.
Disabling the shpc by default will make slot 0 usable at boot time
and not only for hot-plug, without loosing any functionality.
Older machines will have shpc enabled for compatibility reasons.
Signed-off-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
msix_init() reports errors with error_report(), which is wrong when
it's used in realize(). The same issue was fixed for msi_init() in
commit 1108b2f. In order to make the API change as small as possible,
leave the return value check to later patch.
For some devices(like e1000e, vmxnet3, nvme) who won't fail because of
msix_init's failure, suppress the error report by passing NULL error
object.
Bonus: add comment for msix_init.
CC: Jiri Pirko <jiri@resnulli.us>
CC: Gerd Hoffmann <kraxel@redhat.com>
CC: Dmitry Fleytman <dmitry@daynix.com>
CC: Jason Wang <jasowang@redhat.com>
CC: Michael S. Tsirkin <mst@redhat.com>
CC: Hannes Reinecke <hare@suse.de>
CC: Paolo Bonzini <pbonzini@redhat.com>
CC: Alex Williamson <alex.williamson@redhat.com>
CC: Markus Armbruster <armbru@redhat.com>
CC: Marcel Apfelbaum <marcel@redhat.com>
Signed-off-by: Cao jin <caoj.fnst@cn.fujitsu.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
