This function reads the value of the PCI_CLASS_PROG register for PCI IDE
controllers and configures the PCI BARs and/or IDE ioports accordingly.
In the case where we switch to legacy mode, the PCI BARs are set to return zero
(as suggested in the "PCI IDE Controller" specification), the legacy IDE ioports
are enabled, and the PCI interrupt pin cleared to indicate legacy IRQ routing.
Conversely when we switch to native mode, the legacy IDE ioports are disabled
and the PCI interrupt pin set to indicate native IRQ routing. The contents of
the PCI BARs are unspecified, but this is not an issue since if a PCI IDE
controller has been switched to native mode then its BARs will need to be
programmed.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-ID: <20231116103355.588580-3-mark.cave-ayland@ilande.co.uk>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
These definitions are present in ioport.c which is currently only available when
CONFIG_IDE_ISA is enabled. Move them to the IDE core so that they can be made
available to PCI IDE controllers that support switching to legacy mode.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-ID: <20231116103355.588580-2-mark.cave-ayland@ilande.co.uk>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Every TYPE_PCI_IDE device performs the same not-so-trivial bit manipulation by
copy'n'paste code. Extract this into bmdma_status_writeb(), mirroring
bmdma_cmd_writeb().
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-Id: <20230531211043.41724-6-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Bring the block files in line with the QEMU coding style, with spaces
for indentation. This patch partially resolves the issue 371.
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/371
Signed-off-by: Yeqi Fu <fufuyqqqqqq@gmail.com>
Message-Id: <20230315043229.62100-1-fufuyqqqqqq@gmail.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
These legacy ISA IRQs allow the PIIX IDE functions to be wired up in
their south bridges and the VIA IDE functions to disuse
PCI_INTERRUPT_LINE as outlined in https://lists.nongnu.org/archive/html/qemu-devel/2020-03/msg01707.html
Suggested-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230126211740.66874-7-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
The function is only used inside ide/pci.c, so doesn't need to be exported.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230215112712.23110-18-philmd@linaro.org>
ide_get_geometry() and ide_get_bios_chs_trans() are only
used by the TYPE_PC_MACHINE.
"hw/ide.h" is a mixed bag of lost IDE declarations. In order
to remove this (almost) pointless header soon, move these
declarations to "hw/ide/internal.h".
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20230220091358.17038-18-philmd@linaro.org>
idebus_active_if() operates on a IDEBus; rename it as
ide_bus_active_if() to emphasize its first argument
is a IDEBus.
Mechanical change using:
$ sed -i -e 's/idebus_active_if/ide_bus_active_if/g' \
$(git grep -l idebus_active_if)
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230215112712.23110-16-philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
ide_init2() initializes a IDEBus, and set its output IRQ.
To emphasize this, rename it as ide_bus_init_output_irq().
Mechanical change using:
$ sed -i -e 's/ide_init2/ide_bus_init_output_irq/g' \
$(git grep -l ide_init2)
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230215112712.23110-15-philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
ide_exec_cmd() operates on a IDEBus; rename it as
ide_bus_exec_cmd() to emphasize its first argument
is a IDEBus.
Mechanical change using:
$ sed -i -e 's/ide_exec_cmd/ide_bus_exec_cmd/g' \
$(git grep -wl ide_exec_cmd)
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230215112712.23110-14-philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
ide_register_restart_cb() operates on a IDEBus; rename it as
ide_bus_register_restart_cb() to emphasize its first argument
is a IDEBus.
Mechanical change using:
$ sed -i -e 's/ide_register_restart_cb/ide_bus_register_restart_cb/g' \
$(git grep -l ide_register_restart_cb)
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230215112712.23110-13-philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
ide_create_drive() operates on a IDEBus; rename it as
ide_bus_create_drive() to emphasize its first argument
is a IDEBus.
Mechanical change using:
$ sed -i -e 's/ide_create_drive/ide_bus_create_drive/g' \
$(git grep -wl ide_create_drive)
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230215112712.23110-12-philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
ide_set_irq() operates on a IDEBus; rename it as
ide_bus_set_irq() to emphasize its first argument
is a IDEBus.
Mechanical change using:
$ sed -i -e 's/ide_set_irq/ide_bus_set_irq/g' \
$(git grep -l ide_set_irq)
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230215112712.23110-11-philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Only include "hw/irq.h" where appropriate.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230215112712.23110-10-philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
The IDEBus structure has PortioList fields, so we need its
declarations from "exec/ioport.h". "hw/isa/isa.h" is not required.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230215112712.23110-9-philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Missed in commit d7458e7754 ("hw/ide/internal: Remove unused
DMARestartFunc typedef") which removed the single use of RunState.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230215112712.23110-8-philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Only atapi.c requires the SCSI constants. No need to include
it in all files including "hw/ide/internal.h".
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230215112712.23110-7-philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
"hw/ide.h" is a mixed bag of lost IDE declarations.
Extract isa_ide_init() and the TYPE_ISA_IDE QOM declarations
to a new "hw/ide/isa.h" header.
Rename ISAIDEState::isairq as 'irqnum' to emphasize this is
not a qemu_irq object but the number (index) of an ISA IRQ.
Message-Id: <20230215112712.23110-5-philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Bernhard Beschow <shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
"hw/ide.h" is a mixed bag of lost IDE declarations.
Extract mmio_ide_init_drives() and the TYPE_MMIO_IDE QOM
declarations to a new "hw/ide/mmio.h" header.
Document the SysBus interface.
Message-Id: <20230215112712.23110-4-philmd@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
mostly vhost-vdpa:
guest announce feature emulation when using shadow virtqueue
support for configure interrupt
startup speed ups
an acpi change to only generate cluster node in PPTT when specified for arm
misc fixes, cleanups
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAmO6eGMPHG1zdEByZWRo
YXQuY29tAAoJECgfDbjSjVRpoUIIALqC3UtJcK3AuAMbeqVokxl5CPwoeXMyi+rT
0QuN8m8dpBtJFpy3Vyq0afixOFmlwvORW5ye4QI97OyIhtLJq00buzQsgHjNoPo3
zN2L0BDyofDmfFHgCxcEbv2aAO8TaqRSHmKffEFmf8JDMDL9Ev1QvPTWHhfm2eJf
VKPHOtCA/3WXBD9JNfYJ0YuzCrrJaMhIO6/5tqv9yjMxWTfEFa1J2Sr2tWkRLuDk
FPfApy7afjI705Guv6PllZ3JdOMwf7iZaoBK6mSdCDSyi1xciYM0VeWi8SLD4qbM
N+9NkUQOIYS5ZC4BXrULy6HDUsECJ71I0pvHveX7nwbK6xPD4RQ=
=0tPe
-----END PGP SIGNATURE-----
Merge tag 'for_upstream' of https://git.kernel.org/pub/scm/virt/kvm/mst/qemu into staging
virtio,pc,pci: features, cleanups, fixes
mostly vhost-vdpa:
guest announce feature emulation when using shadow virtqueue
support for configure interrupt
startup speed ups
an acpi change to only generate cluster node in PPTT when specified for arm
misc fixes, cleanups
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Sun 08 Jan 2023 08:01:39 GMT
# gpg: using RSA key 5D09FD0871C8F85B94CA8A0D281F0DB8D28D5469
# gpg: issuer "mst@redhat.com"
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>" [full]
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>" [full]
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* tag 'for_upstream' of https://git.kernel.org/pub/scm/virt/kvm/mst/qemu: (50 commits)
vhost-scsi: fix memleak of vsc->inflight
acpi: cpuhp: fix guest-visible maximum access size to the legacy reg block
tests: acpi: aarch64: Add *.topology tables
tests: acpi: aarch64: Add topology test for aarch64
tests: acpi: Add and whitelist *.topology blobs
tests: virt: Update expected ACPI tables for virt test
hw/acpi/aml-build: Only generate cluster node in PPTT when specified
tests: virt: Allow changes to PPTT test table
virtio-pci: fix proxy->vector_irqfd leak in virtio_pci_set_guest_notifiers
vdpa: commit all host notifier MRs in a single MR transaction
vhost: configure all host notifiers in a single MR transaction
vhost: simplify vhost_dev_enable_notifiers
vdpa: harden the error path if get_iova_range failed
vdpa-dev: get iova range explicitly
docs/devel: Rules on #include in headers
include: Include headers where needed
include/hw/virtio: Break inclusion loop
include/hw/cxl: Break inclusion loop cxl_pci.h and cxl_cdat_h
include/hw/pci: Include hw/pci/pci.h where needed
include/hw/pci: Split pci_device.h off pci.h
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
PCIDeviceClass and PCIDevice are defined in pci.h. Many users of the
header don't actually need them. Similar structs live in their own
headers: PCIBusClass and PCIBus in pci_bus.h, PCIBridge in
pci_bridge.h, PCIHostBridgeClass and PCIHostState in pci_host.h,
PCIExpressHost in pcie_host.h, and PCIERootPortClass, PCIEPort, and
PCIESlot in pcie_port.h.
Move PCIDeviceClass and PCIDeviceClass to new pci_device.h, along with
the code that needs them. Adjust include directives.
This also enables the next commit.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20221222100330.380143-6-armbru@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
CompactFlash uses features 0x01 and 0x81 to enable/disable 8-bit data
path. Implement them.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Message-Id: <20221130120238.706717-1-lkundrak@v3.sk>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Suggested-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20221022150508.26830-9-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
CHS-based disk utilities and operating systems may adjust the logical
geometry of a hard drive to cope with the expectations or limitations
of software using the ATA INITIALIZE_DEVICE_PARAMETERS command.
Prior to this patch, INITIALIZE_DEVICE_PARAMETERS was a nop that
always returned success, raising the possibility of data loss or
corruption if the CHS<->LBA translation redirected a write to the
wrong sector.
* hw/ide/core.c
ide_reset():
Reset the logical CHS geometry of the hard disk when the power-on
defaults feature is enabled.
cmd_specify():
a) New function implementing INITIALIZE_DEVICE_PARAMETERS.
b) Ignore calls for empty or ATAPI devices.
cmd_set_features():
Implement the power-on defaults enable and disable features.
struct ide_cmd_table:
Switch WIN_SPECIFY from cmd_nop() to cmd_specify().
ide_init_drive():
Set new fields 'drive_heads' and 'drive_sectors' based upon the
actual disk geometry.
* include/hw/ide/internal.h
struct IDEState:
a) Store the actual drive CHS values within the new fields
'drive_heads' and 'drive_sectors.'
b) Track whether a soft IDE reset should also reset the logical CHS
geometry of the hard disk within the new field 'reset_reverts'.
Signed-off-by: Lev Kujawski <lkujaw@member.fsf.org>
Message-Id: <20220707031140.158958-7-lkujaw@member.fsf.org>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The function ide_bus_new() does an in-place initialization. Rename
it to ide_bus_init() to follow our _init vs _new convention.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Acked-by: John Snow <jsnow@redhat.com> (Feel free to merge.)
Message-id: 20210923121153.23754-7-peter.maydell@linaro.org
QEMU currently crashes when the user tries to do something like:
qemu-system-x86_64 -M x-remote -device piix3-ide
This happens because the "isabus" variable is not initialized with
the x-remote machine yet. Add a proper check for this condition
and propagate the error to the caller, so we can fail there gracefully.
Message-Id: <20210416125256.2039734-1-thuth@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
There is no "version 2" of the "Lesser" General Public License.
It is either "GPL version 2.0" or "Lesser GPL version 2.1".
This patch replaces all occurrences of "Lesser GPL version 2" with
"Lesser GPL version 2.1" in comment section.
This patch contains all the files, whose maintainer I could not get
from ‘get_maintainer.pl’ script.
Signed-off-by: Chetan Pant <chetan4windows@gmail.com>
Message-Id: <20201023124424.20177-1-chetan4windows@gmail.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
[thuth: Adapted exec.c and qdev-monitor.c to new location]
Signed-off-by: Thomas Huth <thuth@redhat.com>
(In QEMU, we call this the "select" register.)
My memory isn't good enough to memorize what these magic runes
do. Label them to prevent mixups from happening in the future.
Side note: I assume it's safe to always set 0xA0 even though ATA2 claims
these bits are reserved, because ATA3 immediately reinstated that these
bits should be always on. ATA4 and subsequent specs only claim that the
fields are obsolete, so I assume it's safe to leave these set and that
it should work with the widest array of guests.
Signed-off-by: John Snow <jsnow@redhat.com>
I have been staring at this FIXME for years and I never knew what it
meant. I finally stumbled across it!
When writing to the command registers, the old value is shifted into a
HOB copy of the register and the new value is written into the primary
register. When reading registers, the value retrieved is dependent on
the HOB bit in the CONTROL register.
By setting bit 7 (0x80) in CONTROL, any register read will, if it has
one, yield the HOB value for that register instead.
Our code has a problem: We were using bit 7 of the DEVICE register to
model this. We use bus->cmd roughly as the control register already, as
it stores the value from ide_ctrl_write.
Lastly, all command register writes reset the HOB, so fix that, too.
Signed-off-by: John Snow <jsnow@redhat.com>
It's the Control register, part of the Control block -- Command is
misleading here. Rename all related functions and constants.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Make the type checking macro name consistent with the TYPE_*
constant.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200902224311.1321159-33-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Some typedefs and macros are defined after the type check macros.
This makes it difficult to automatically replace their
definitions with OBJECT_DECLARE_TYPE.
Patch generated using:
$ ./scripts/codeconverter/converter.py -i \
--pattern=QOMStructTypedefSplit $(git grep -l '' -- '*.[ch]')
which will split "typdef struct { ... } TypedefName"
declarations.
Followed by:
$ ./scripts/codeconverter/converter.py -i --pattern=MoveSymbols \
$(git grep -l '' -- '*.[ch]')
which will:
- move the typedefs and #defines above the type check macros
- add missing #include "qom/object.h" lines if necessary
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20200831210740.126168-9-ehabkost@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20200831210740.126168-10-ehabkost@redhat.com>
Message-Id: <20200831210740.126168-11-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Move the ALLWINNER_AHCI macro close to the TYPE_ALLWINNER_AHCI
define.
This will make future conversion to OBJECT_DECLARE* easier.
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Tested-By: Roman Bolshakov <r.bolshakov@yadro.com>
Message-Id: <20200825192110.3528606-33-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
The TYPE_* constants and the typedefs are defined in ahci.h, so
we can move the type checking macros there too.
This will make future conversion to OBJECT_DECLARE* easier.
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Tested-By: Roman Bolshakov <r.bolshakov@yadro.com>
Message-Id: <20200825192110.3528606-31-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Handlers don't need to modify the IDEDMA structure.
Make it const.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200512194917.15807-1-philmd@redhat.com>
Acked-by: John Snow <jsnow@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
We can move this define now that less files use it to internal.h to
further reduce dependency on hw/ide.h.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Message-id: e68675d2f6252f229cf788b7cd163bb76fa3e26b.1584457537.git.balaton@eik.bme.hu
Signed-off-by: John Snow <jsnow@redhat.com>
The pci_ide_create_devs() function takes a hd_table parameter but all
callers just pass what ide_drive_get() returns so we can do it locally
simplifying callers and removing hd_table parameter.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Message-id: e9713fdded4d212fa68ed03b844e531934226a6f.1584457537.git.balaton@eik.bme.hu
Signed-off-by: John Snow <jsnow@redhat.com>
After previous patches we don't need hw/pci/pci.h any more in
hw/ide.h. Some files depended on implicit inclusion by this header
which are also fixed up here.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Message-id: 444a5e34331bf1f7880541b8d46e0353f470f5a6.1584457537.git.balaton@eik.bme.hu
Signed-off-by: John Snow <jsnow@redhat.com>
In my "build everything" tree, changing sysemu/sysemu.h triggers a
recompile of some 1800 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h, down from 5400 due to the
previous commit).
Several headers include sysemu/sysemu.h just to get typedef
VMChangeStateEntry. Move it from sysemu/sysemu.h to qemu/typedefs.h.
Spell its structure tag the same while there. Drop the now
superfluous includes of sysemu/sysemu.h from headers.
Touching sysemu/sysemu.h now recompiles some 1100 objects.
qemu/uuid.h also drops from 1800 to 1100, and
qapi/qapi-types-run-state.h from 5000 to 4400.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190812052359.30071-29-armbru@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
In my "build everything" tree, changing hw/irq.h triggers a recompile
of some 5400 out of 6600 objects (not counting tests and objects that
don't depend on qemu/osdep.h).
hw/hw.h supposedly includes it for convenience. Several other headers
include it just to get qemu_irq and.or qemu_irq_handler.
Move the qemu_irq and qemu_irq_handler typedefs from hw/irq.h to
qemu/typedefs.h, and then include hw/irq.h only where it's still
needed. Touching it now recompiles only some 500 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190812052359.30071-13-armbru@redhat.com>
@iov is used only to initialize @qiov. Let's use new
qemu_iovec_init_buf() instead, which simplifies the code.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 20190218140926.333779-18-vsementsov@virtuozzo.com
Message-Id: <20190218140926.333779-18-vsementsov@virtuozzo.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
@iov is used only to initialize @qiov. Let's use new
qemu_iovec_init_buf() instead, which simplifies the code.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 20190218140926.333779-17-vsementsov@virtuozzo.com
Message-Id: <20190218140926.333779-17-vsementsov@virtuozzo.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
@iov is used only to initialize @qiov. Let's use new
qemu_iovec_init_buf() instead, which simplifies the code.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 20190218140926.333779-16-vsementsov@virtuozzo.com
Message-Id: <20190218140926.333779-16-vsementsov@virtuozzo.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Now that no CMD646 specific parts are left in CMD646BAR (all remaining
members are really PCI IDE specific) this struct can be deleted moving
the memory regions for PCI IDE BARs to PCIIDEState where they better
belong. The CMD646 PCI IDE model is adjusted accordingly.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Tested-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: John Snow <jsnow@redhat.com>
Message-id: 4b6cb2ae150dc0d21178209e4beb1e35140a7325.1547166960.git.balaton@eik.bme.hu
Signed-off-by: John Snow <jsnow@redhat.com>
The io mem ops callbacks are not specific to CMD646 but really follow
the PCI IDE spec so move these from cmd646.c to pci.c to allow other
PCI IDE implementations to use them.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Tested-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: John Snow <jsnow@redhat.com>
Message-id: a2b1b2b74afdc78330b8b75605687f683a249635.1547166960.git.balaton@eik.bme.hu
Signed-off-by: John Snow <jsnow@redhat.com>
