The QMP and HMP interfaces can be used by monitor or QMP tools to retrieve
the SGX information from VM side when SGX is enabled on Intel platform.
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Message-Id: <20210910102258.46648-2-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add helpers to detect if SGX EPC exists above 4g, and if so, where SGX
EPC above 4g ends. Use the helpers to adjust the device memory range
if SGX EPC exists above 4g.
For multiple virtual EPC sections, we just put them together physically
contiguous for the simplicity because we don't support EPC NUMA affinity
now. Once the SGX EPC NUMA support in the kernel SGX driver, we will
support this in the future.
Note that SGX EPC is currently hardcoded to reside above 4g.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Message-Id: <20210719112136.57018-18-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Expose SGX to the guest if and only if KVM is enabled and supports
virtualization of SGX. While the majority of ENCLS can be emulated to
some degree, because SGX uses a hardware-based root of trust, the
attestation aspects of SGX cannot be emulated in software, i.e.
ultimately emulation will fail as software cannot generate a valid
quote/report. The complexity of partially emulating SGX in Qemu far
outweighs the value added, e.g. an SGX specific simulator for userspace
applications can emulate SGX for development and testing purposes.
Note, access to the PROVISIONKEY is not yet advertised to the guest as
KVM blocks access to the PROVISIONKEY by default and requires userspace
to provide additional credentials (via ioctl()) to expose PROVISIONKEY.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Message-Id: <20210719112136.57018-13-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Because SGX EPC is enumerated through CPUID, EPC "devices" need to be
realized prior to realizing the vCPUs themselves, i.e. long before
generic devices are parsed and realized. From a virtualization
perspective, the CPUID aspect also means that EPC sections cannot be
hotplugged without paravirtualizing the guest kernel (hardware does
not support hotplugging as EPC sections must be locked down during
pre-boot to provide EPC's security properties).
So even though EPC sections could be realized through the generic
-devices command, they need to be created much earlier for them to
actually be usable by the guest. Place all EPC sections in a
contiguous block, somewhat arbitrarily starting after RAM above 4g.
Ensuring EPC is in a contiguous region simplifies calculations, e.g.
device memory base, PCI hole, etc..., allows dynamic calculation of the
total EPC size, e.g. exposing EPC to guests does not require -maxmem,
and last but not least allows all of EPC to be enumerated in a single
ACPI entry, which is expected by some kernels, e.g. Windows 7 and 8.
The new compound properties command for sgx like below:
......
-object memory-backend-epc,id=mem1,size=28M,prealloc=on \
-object memory-backend-epc,id=mem2,size=10M \
-M sgx-epc.0.memdev=mem1,sgx-epc.1.memdev=mem2
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Message-Id: <20210719112136.57018-6-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
SGX EPC is enumerated through CPUID, i.e. EPC "devices" need to be
realized prior to realizing the vCPUs themselves, which occurs long
before generic devices are parsed and realized. Because of this,
do not allow 'sgx-epc' devices to be instantiated after vCPUS have
been created.
The 'sgx-epc' device is essentially a placholder at this time, it will
be fully implemented in a future patch along with a dedicated command
to create 'sgx-epc' devices.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Message-Id: <20210719112136.57018-5-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
EPC (Enclave Page Cahe) is a specialized type of memory used by Intel
SGX (Software Guard Extensions). The SDM desribes EPC as:
The Enclave Page Cache (EPC) is the secure storage used to store
enclave pages when they are a part of an executing enclave. For an
EPC page, hardware performs additional access control checks to
restrict access to the page. After the current page access checks
and translations are performed, the hardware checks that the EPC
page is accessible to the program currently executing. Generally an
EPC page is only accessed by the owner of the executing enclave or
an instruction which is setting up an EPC page.
Because of its unique requirements, Linux manages EPC separately from
normal memory. Similar to memfd, the device /dev/sgx_vepc can be
opened to obtain a file descriptor which can in turn be used to mmap()
EPC memory.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Message-Id: <20210719112136.57018-3-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add a new RAMBlock flag to denote "protected" memory, i.e. memory that
looks and acts like RAM but is inaccessible via normal mechanisms,
including DMA. Use the flag to skip protected memory regions when
mapping RAM for DMA in VFIO.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Each Nubus slot has an IRQ line that can be used to request service from the
CPU. Connect the IRQs to the Nubus bridge so that they can be wired up using qdev
gpios accordingly, and introduce a new nubus_set_irq() function that can be used
by Nubus devices to control the slot IRQ.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210924073808.1041-19-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Since nubus-bridge is a container for NubusBus then it should be embedded
directly within the bridge device using qbus_create_inplace().
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210924073808.1041-17-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Now that Nubus has its own address space rather than mapping directly into the
system bus, move the Nubus reference from MacNubusBridge to NubusBridge.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210924073808.1041-16-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
This better reflects that the mac-nubus-bridge device is derived from the
nubus-bridge device, and that the structure represents the state of the bridge
device and not the Nubus itself. Also update the comment in the file header to
reflect that mac-nubus-bridge is specific to the Macintosh.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210924073808.1041-15-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
This is to allow the Nubus bridge to store its own additional state. Also update
the comment in the file header to reflect that nubus-bridge is not specific to
the Macintosh.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210924073808.1041-14-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
According to "Designing Cards and Drivers for the Macintosh Family" the Nubus
has its own 32-bit address space based upon physical slot addressing.
Move Nubus to its own 32-bit address space and then use memory region aliases
to map available slot and super slot ranges into the q800 system address
space via the Macintosh Nubus bridge.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210924073808.1041-13-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The declaration ROM is located at the top-most address of the standard slot
space.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210924073808.1041-12-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Since there is no need to generate a dummy declaration ROM, remove both
nubus_register_rom() and nubus_register_format_block(). These will shortly be
replaced with a mechanism to optionally load a declaration ROM from disk to
allow real images to be used within QEMU.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210924073808.1041-11-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Convert nubus_device_realize() to use a bitmap to manage available slots to allow
for future Nubus devices to be plugged into arbitrary slots from the command line
using a new qdev "slot" parameter for nubus devices.
Update mac_nubus_bridge_init() to only allow slots 0x9 to 0xe on Macintosh machines
as documented in "Designing Cards and Drivers for the Macintosh Family".
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210924073808.1041-5-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
According to "Designing Cards and Drivers for the Macintosh Family" each physical
nubus slot can access 2 separate address ranges: a super slot memory region which
is 256MB and a standard slot memory region which is 16MB.
Currently a Nubus device uses the physical slot number to determine whether it is
using a standard slot memory region or a super slot memory region rather than
exposing both memory regions for use as required.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210924073808.1041-4-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
This is in preparation for creating a qdev property of the same name.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210924073808.1041-3-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The PC_ROM_* definitions are only used by the PC machine,
and are irrelevant to the other architectures / machines.
Reduce their scope by moving them to hw/i386/pc.c.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210917185949.2244956-1-philmd@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Fix is added to check for reserved value in select field for
namespace attachment
CC: Minwoo Im <minwoo.im.dev@gmail.com>
Signed-off-by: Naveen Nagar <naveen.n1@samsung.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
While we may have had some thought of allowing system-mode
to return from this hook, we have no guests that require this.
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
There is nothing target specific about this. The implementation
is host specific, but the declaration is 100% common.
Reviewed-By: Warner Losh <imp@bsdimp.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
- ePMP CSR address updates
- Convert internal interrupts to use QEMU GPIO lines
- SiFive PWM support
- Support for RISC-V ACLINT
- SiFive PDMA fixes
- Update to u-boot instructions for sifive_u
- mstatus.SD bug fix for hypervisor extensions
- OpenTitan fix for USB dev address
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEE9sSsRtSTSGjTuM6PIeENKd+XcFQFAmFJgSoACgkQIeENKd+X
cFQTOwf8DC7rBqOWQS3v/r+H2hlfDqW+4G3pPPBcoyCEiqO+cL26ox+EmTHDbieh
+0yWyp7L6SU/zcJ86oBAFNGH46ltXuUKOYWhkfA1QwlGzAwjZ82hnZ3jJqXf1jin
Wq0ElzKk6rvcRkHTVhdjkGvoxskaXPQ/kFzyTHrxMDlkmHO3L4IaYe0xsamRI11D
E7UJC97YmpSAsCNUc5irpkeLyiFobyR8TEL3nBEPK/6Xj0ojRT4zoGe1EotC7+sN
zL8a9ZuU0bL3rQH8Ai7wnXBP8D2PQa0tZQV6wne/BzeEUSpKrC/rGW73vQCz0Pps
U8VNkIlbAqD1s6aXlqE24H535x10Mw==
=WYF5
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/alistair23/tags/pull-riscv-to-apply-20210921' into staging
Second RISC-V PR for QEMU 6.2
- ePMP CSR address updates
- Convert internal interrupts to use QEMU GPIO lines
- SiFive PWM support
- Support for RISC-V ACLINT
- SiFive PDMA fixes
- Update to u-boot instructions for sifive_u
- mstatus.SD bug fix for hypervisor extensions
- OpenTitan fix for USB dev address
# gpg: Signature made Mon 20 Sep 2021 11:52:26 PM PDT
# gpg: using RSA key F6C4AC46D4934868D3B8CE8F21E10D29DF977054
# gpg: Good signature from "Alistair Francis <alistair@alistair23.me>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: F6C4 AC46 D493 4868 D3B8 CE8F 21E1 0D29 DF97 7054
* remotes/alistair23/tags/pull-riscv-to-apply-20210921: (21 commits)
hw/riscv: opentitan: Correct the USB Dev address
target/riscv: csr: Rename HCOUNTEREN_CY and friends
target/riscv: Backup/restore mstatus.SD bit when virtual register swapped
docs/system/riscv: sifive_u: Update U-Boot instructions
hw/dma: sifive_pdma: don't set Control.error if 0 bytes to transfer
hw/dma: sifive_pdma: allow non-multiple transaction size transactions
hw/dma: sifive_pdma: claim bit must be set before DMA transactions
hw/dma: sifive_pdma: reset Next* registers when Control.claim is set
hw/riscv: virt: Add optional ACLINT support to virt machine
hw/riscv: virt: Re-factor FDT generation
hw/intc: Upgrade the SiFive CLINT implementation to RISC-V ACLINT
hw/intc: Rename sifive_clint sources to riscv_aclint sources
sifive_u: Connect the SiFive PWM device
hw/timer: Add SiFive PWM support
hw/intc: ibex_timer: Convert the timer to use RISC-V CPU GPIO lines
hw/intc: sifive_plic: Convert the PLIC to use RISC-V CPU GPIO lines
hw/intc: ibex_plic: Convert the PLIC to use RISC-V CPU GPIO lines
hw/intc: sifive_clint: Use RISC-V CPU GPIO lines
target/riscv: Expose interrupt pending bits as GPIO lines
target/riscv: Fix satp write
...
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Sleep on WFI until the VTIMER is due but allow ourselves to be woken
up on IPI.
In this implementation IPI is blocked on the CPU thread at startup and
pselect() is used to atomically unblock the signal and begin sleeping.
The signal is sent unconditionally so there's no need to worry about
races between actually sleeping and the "we think we're sleeping"
state. It may lead to an extra wakeup but that's better than missing
it entirely.
Signed-off-by: Peter Collingbourne <pcc@google.com>
Signed-off-by: Alexander Graf <agraf@csgraf.de>
Acked-by: Roman Bolshakov <r.bolshakov@yadro.com>
Reviewed-by: Sergio Lopez <slp@redhat.com>
Message-id: 20210916155404.86958-6-agraf@csgraf.de
[agraf: Remove unused 'set' variable, always advance PC on WFX trap,
support vm stop / continue operations and cntv offsets]
Signed-off-by: Alexander Graf <agraf@csgraf.de>
Acked-by: Roman Bolshakov <r.bolshakov@yadro.com>
Reviewed-by: Sergio Lopez <slp@redhat.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We extend virt machine to emulate ACLINT devices only when "aclint=on"
parameter is passed along with machine name in QEMU command-line.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Message-id: 20210831110603.338681-5-anup.patel@wdc.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The RISC-V ACLINT is more modular and backward compatible with
original SiFive CLINT so instead of duplicating the original
SiFive CLINT implementation we upgrade the current SiFive CLINT
implementation to RISC-V ACLINT implementation.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Message-id: 20210831110603.338681-3-anup.patel@wdc.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
We will be upgrading SiFive CLINT implementation into RISC-V ACLINT
implementation so let's first rename the sources.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Message-id: 20210831110603.338681-2-anup.patel@wdc.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This is the initial commit of the SiFive PWM timer. This is used by
guest software as a timer and is included in the SiFive FU540 SoC.
Signed-off-by: Justin Restivo <jrestivo@draper.com>
Signed-off-by: Alexandra Clifford <aclifford@draper.com>
Signed-off-by: Amanda Strnad <astrnad@draper.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Message-id: 9f70a210acbfaf0e1ea6ad311ab892ac69134d8b.1631159656.git.alistair.francis@wdc.com
Instead of using riscv_cpu_update_mip() let's instead use the new RISC-V
CPU GPIO lines to set the timer MIP bits.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 84d5b1d5783d2e79eee69a2f7ac480cc0c070db3.1630301632.git.alistair.francis@wdc.com
Instead of using riscv_cpu_update_mip() let's instead use the new RISC-V
CPU GPIO lines to set the external MIP bits.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Message-id: 0364190bfa935058a845c0fa1ecf650328840ad5.1630301632.git.alistair.francis@wdc.com
Instead of using riscv_cpu_update_mip() let's instead use the new RISC-V
CPU GPIO lines to set the external MIP bits.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 0a76946981852f5bd15f0c37ab35b253371027a8.1630301632.git.alistair.francis@wdc.com
Instead of using riscv_cpu_update_mip() let's instead use the new RISC-V
CPU GPIO lines to set the timer and soft MIP bits.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: LIU Zhiwei <zhiwei_liu@c-sky.com>
Message-id: 946e1ef5e268b24084c7ddad84c146de62a56736.1630301632.git.alistair.francis@wdc.com
With Apple Silicon available to the masses, it's a good time to add support
for driving its virtualization extensions from QEMU.
This patch adds all necessary architecture specific code to get basic VMs
working, including save/restore.
Known limitations:
- WFI handling is missing (follows in later patch)
- No watchpoint/breakpoint support
Signed-off-by: Alexander Graf <agraf@csgraf.de>
Reviewed-by: Roman Bolshakov <r.bolshakov@yadro.com>
Reviewed-by: Sergio Lopez <slp@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20210916155404.86958-5-agraf@csgraf.de
[PMM: added missing #include]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We will need to install a migration helper for the ARM hvf backend.
Let's introduce an arch callback for the overall hvf init chain to
do so.
Signed-off-by: Alexander Graf <agraf@csgraf.de>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20210916155404.86958-4-agraf@csgraf.de
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When you run QEMU with an Aspeed machine and a single serial device
using stdio like this:
qemu -machine ast2600-evb -drive ... -serial stdio
The guest OS can read and write to the UART5 registers at 0x1E784000 and
it will receive from stdin and write to stdout. The Aspeed SoC's have a
lot more UART's though (AST2500 has 5, AST2600 has 13) and depending on
the board design, may be using any of them as the serial console. (See
"stdout-path" in a DTS to check which one is chosen).
Most boards, including all of those currently defined in
hw/arm/aspeed.c, just use UART5, but some use UART1. This change adds
some flexibility for different boards without requiring users to change
their command-line invocation of QEMU.
I tested this doesn't break existing code by booting an AST2500 OpenBMC
image and an AST2600 OpenBMC image, each using UART5 as the console.
Then I tested switching the default to UART1 and booting an AST2600
OpenBMC image that uses UART1, and that worked too.
Signed-off-by: Peter Delevoryas <pdel@fb.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210901153615.2746885-2-pdel@fb.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This is the latest revision of the ASPEED 2600 SoC. As there is no
need to model multiple revisions of the same SoC for the moment,
update the SCU AST2600 to model the A3 revision instead of the A1 and
adapt the AST2600 SoC and machines.
Reset values are taken from v8 of the datasheet.
Signed-off-by: Joel Stanley <joel@jms.id.au>
[ clg: - Introduced an Aspeed "ast2600-a3" SoC class
- Commit log update ]
Message-Id: <20210629142336.750058-3-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
While some of the critical fields remain the same, there is variation in
the definition of the control register across the SoC generations.
Reserved regions are adjusted, while in other cases the mutability or
behaviour of fields change.
Introduce a callback to sanitize the value on writes to ensure model
behaviour reflects the hardware.
Fixes: 854123bf8d ("wdt: Add Aspeed watchdog device model")
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210709053107.1829304-2-andrew@aj.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
.bdrv_co_block_status() implementations are free to return a *pnum that
exceeds @bytes, because bdrv_co_block_status() in block/io.c will clamp
*pnum as necessary.
On the other hand, if drivers' implementations return values for *pnum
that are as large as possible, our recently introduced block-status
cache will become more effective.
So, make a note in block_int.h that @bytes is no upper limit for *pnum.
Suggested-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Hanna Reitz <hreitz@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-Id: <20210812084148.14458-4-hreitz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
As we have attempted before
(https://lists.gnu.org/archive/html/qemu-devel/2019-01/msg06451.html,
"file-posix: Cache lseek result for data regions";
https://lists.nongnu.org/archive/html/qemu-block/2021-02/msg00934.html,
"file-posix: Cache next hole"), this patch seeks to reduce the number of
SEEK_DATA/HOLE operations the file-posix driver has to perform. The
main difference is that this time it is implemented as part of the
general block layer code.
The problem we face is that on some filesystems or in some
circumstances, SEEK_DATA/HOLE is unreasonably slow. Given the
implementation is outside of qemu, there is little we can do about its
performance.
We have already introduced the want_zero parameter to
bdrv_co_block_status() to reduce the number of SEEK_DATA/HOLE calls
unless we really want zero information; but sometimes we do want that
information, because for files that consist largely of zero areas,
special-casing those areas can give large performance boosts. So the
real problem is with files that consist largely of data, so that
inquiring the block status does not gain us much performance, but where
such an inquiry itself takes a lot of time.
To address this, we want to cache data regions. Most of the time, when
bad performance is reported, it is in places where the image is iterated
over from start to end (qemu-img convert or the mirror job), so a simple
yet effective solution is to cache only the current data region.
(Note that only caching data regions but not zero regions means that
returning false information from the cache is not catastrophic: Treating
zeroes as data is fine. While we try to invalidate the cache on zero
writes and discards, such incongruences may still occur when there are
other processes writing to the image.)
We only use the cache for nodes without children (i.e. protocol nodes),
because that is where the problem is: Drivers that rely on block-status
implementations outside of qemu (e.g. SEEK_DATA/HOLE).
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/307
Signed-off-by: Hanna Reitz <hreitz@redhat.com>
Message-Id: <20210812084148.14458-3-hreitz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
[hreitz: Added `local_file == bs` assertion, as suggested by Vladimir]
Signed-off-by: Hanna Reitz <hreitz@redhat.com>
There is a comment above the BDS definition stating care must be taken
to consider handling newly added fields in bdrv_append().
Actually, this comment should have said "bdrv_swap()" as of 4ddc07cac
(nine years ago), and in any case, bdrv_swap() was dropped in
8e419aefa (six years ago). So no such care is necessary anymore.
Signed-off-by: Hanna Reitz <hreitz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <20210812084148.14458-2-hreitz@redhat.com>
qdev_init_gpio_out() states it "creates an array of anonymous
output GPIO lines" but doesn't document how this array is
released. Add a note that it is automatically free'd in qdev
instance_finalize().
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20210819142731.2827912-1-philmd@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Instead of immediately drawing and submitting, queue and wait
for the draw signal if the dmabuf submitted is a blob.
Cc: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Vivek Kasireddy <vivek.kasireddy@intel.com>
Message-Id: <20210914211837.3229977-5-vivek.kasireddy@intel.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Create sync objects and fences only for dmabufs that are blobs. Once a
fence is created (after glFlush) and is signalled,
graphic_hw_gl_flushed() will be called and virtio-gpu cmd processing
will be resumed.
Cc: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Vivek Kasireddy <vivek.kasireddy@intel.com>
Message-Id: <20210914211837.3229977-4-vivek.kasireddy@intel.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
These egl helpers would be used for creating and waiting on
a sync object.
Cc: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Vivek Kasireddy <vivek.kasireddy@intel.com>
Message-Id: <20210914211837.3229977-3-vivek.kasireddy@intel.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Yang Zhong
Sean Christopherson
Mark Cave-Ayland
Philippe Mathieu-Daudé
Richard Henderson
Naveen Nagar
Peter Maydell
Peter Collingbourne
Anup Patel
Alistair Francis
Alexander Graf
Peter Delevoryas
Joel Stanley
Andrew Jeffery
Hanna Reitz
Vivek Kasireddy