Apparently GCC gets bent over comparing enum values against zero.
Replace the conditional with something less readable.
Tested-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 20170921013821.1673-1-jsnow@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Replace init with realize in IDEDeviceClass, which has errp
as a parameter. So all the implementations now use error_setg
instead of error_report for reporting error.
Cc: John Snow <jsnow@redhat.com>
Cc: Markus Armbruster <armbru@redhat.com>
Cc: Kevin Wolf <kwolf@redhat.com>
Cc: Max Reitz <mreitz@redhat.com>
Signed-off-by: Mao Zhongyi <maozy.fnst@cn.fujitsu.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Message-id: c4d27b4b5d9e37468e63e35214ce4833ca271542.1505737465.git.maozy.fnst@cn.fujitsu.com
Signed-off-by: John Snow <jsnow@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20170901001502.29915-6-jsnow@redhat.com
[Edited enum conditional for Clang --js]
Signed-off-by: John Snow <jsnow@redhat.com>
To be used sparingly, but still interesting in the case of small
firmwares designed to reproduce bugs in QEMU IDE.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 20170901001502.29915-4-jsnow@redhat.com
Signed-off-by: John Snow <jsnow@redhat.com>
Name the registers for tracing purposes.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 20170901001502.29915-3-jsnow@redhat.com
Signed-off-by: John Snow <jsnow@redhat.com>
Remove the DEBUG_IDE preprocessor definition with something more
appropriately flexible, using the trace-events subsystem.
This will be less prone to bitrot and will more effectively allow
us to target just the functions we care about.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 20170901001502.29915-2-jsnow@redhat.com
Signed-off-by: John Snow <jsnow@redhat.com>
The block backend changed in a way that flushing empty CDROM drives now
crashes. Amend IDE to avoid doing so until the root problem can be
addressed for 2.11.
Original patch by John Snow <jsnow@redhat.com>.
Reported-by: Kieron Shorrock <kshorrock@paloaltonetworks.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-id: 20170809160212.29976-2-stefanha@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
As the pci ahci can be hotplug and unplug, in the ahci unrealize
function it should free all the resource once allocated in the
realized function. This patch add ide_exit to free the resource.
Signed-off-by: Li Qiang <liqiang6-s@360.cn>
Message-id: 1488449293-80280-3-git-send-email-liqiang6-s@360.cn
Signed-off-by: John Snow <jsnow@redhat.com>
Some devices allow a media change between read-only and read-write
media. They need to adapt the permissions in their .change_media_cb()
implementation, which can fail. So add an Error parameter to the
function.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Acked-by: Fam Zheng <famz@redhat.com>
We've traditionally rejected orphans here and there, but not
systematically. For instance, the sun4m machines have an onboard SCSI
HBA (bus=0), and have always rejected bus>0. Other machines with an
onboard SCSI HBA don't.
Commit a66c9dc made all orphans trigger a warning, and the previous
commit turned this into an error. The checks "here and there" are now
redundant. Drop them.
Note that the one in mips_jazz.c was wrong: it rejected bus > MAX_FD,
but MAX_FD is the number of floppy drives per bus.
Error messages change from
$ qemu-system-x86_64 -drive if=ide,bus=2
qemu-system-x86_64: Too many IDE buses defined (3 > 2)
$ qemu-system-mips64 -M magnum,accel=qtest -drive if=floppy,bus=2,id=fd1
qemu: too many floppy drives
$ qemu-system-sparc -M LX -drive if=scsi,bus=1
qemu: too many SCSI bus
to
$ qemu-system-x86_64 -drive if=ide,bus=2
qemu-system-x86_64: -drive if=ide,bus=2: machine type does not support if=ide,bus=2,unit=0
$ qemu-system-mips64 -M magnum,accel=qtest -drive if=floppy,bus=2,id=fd1
qemu-system-mips64: -drive if=floppy,bus=2,id=fd1: machine type does not support if=floppy,bus=2,unit=0
$ qemu-system-sparc -M LX -drive if=scsi,bus=1
qemu-system-sparc: -drive if=scsi,bus=1: machine type does not support if=scsi,bus=1,unit=0
Cc: John Snow <jsnow@redhat.com>
Cc: "Hervé Poussineau" <hpoussin@reactos.org>
Cc: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <1487153147-11530-9-git-send-email-armbru@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
The hard-coded default alignment is BDRV_SECTOR_SIZE, however this is not
necessarily the case for all platforms. Use this as the default alignment for
all current callers.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Eric Blake <eblake@redhat.com>
Acked-by: John Snow <jsnow@redhat.com>
Message-id: 1476445266-27503-2-git-send-email-mark.cave-ayland@ilande.co.uk
Signed-off-by: John Snow <jsnow@redhat.com>
Fix a memory leak in ide_register_restart_cb() in hw/ide/core.c and add
idebus_unrealize() in hw/ide/qdev.c to have calls to
qemu_del_vm_change_state_handler() to deal with the dangling change
state handler during hot-unplugging ide devices which might lead to a
crash.
Signed-off-by: Ashijeet Acharya <ashijeetacharya@gmail.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Message-id: 1474995212-10580-1-git-send-email-ashijeetacharya@gmail.com
[Minor whitespace fix --js]
Signed-off-by: John Snow <jsnow@redhat.com>
ATA8-APT defines the state transitions for both a host controller and
for the hardware device during the lifecycle of a DMA transfer, in
section 9.7 "DMA command protocol."
One of the interesting tidbits here is that when a device transitions
from DDMA0 ("Prepare state") to DDMA1 ("Data_Transfer State"), it can
choose to set either BSY or DRQ to signal this transition, but not both.
as ide_sector_dma_start is the last point in our preparation process
before we begin the real data transfer process (for either AHCI or BMDMA),
this is the correct transition point for DDMA0 to DDMA1.
I have chosen !BSY && DRQ for QEMU to make the transition from DDMA0 the
most obvious.
Reported-by: Benjamin David Lunt <fys@fysnet.net>
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Tested-by: Stefan Weil <sw@weilnetz.de>
Message-id: 1470175541-19344-1-git-send-email-jsnow@redhat.com
Signed-off-by: John Snow <jsnow@redhat.com>
The isa_register_portio_list() function allocates ioports
data/state. Let's keep the reference to this data on some owner. This
isn't enough to fix leaks, but at least, ASAN stops complaining of
direct leaks. Further cleanup would require calling
portio_list_del/destroy().
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
ahci-test /x86_64/ahci/io/dma/lba28/retry triggers the following leak:
Direct leak of 16 byte(s) in 1 object(s) allocated from:
#0 0x7fc4b2a25e20 in malloc (/lib64/libasan.so.3+0xc6e20)
#1 0x7fc4993bce58 in g_malloc (/lib64/libglib-2.0.so.0+0x4ee58)
#2 0x556a187d4b34 in ahci_populate_sglist hw/ide/ahci.c:896
#3 0x556a187d8237 in ahci_dma_prepare_buf hw/ide/ahci.c:1367
#4 0x556a187b5a1a in ide_dma_cb hw/ide/core.c:844
#5 0x556a187d7eec in ahci_start_dma hw/ide/ahci.c:1333
#6 0x556a187b650b in ide_start_dma hw/ide/core.c:921
#7 0x556a187b61e6 in ide_sector_start_dma hw/ide/core.c:911
#8 0x556a187b9e26 in cmd_write_dma hw/ide/core.c:1486
#9 0x556a187bd519 in ide_exec_cmd hw/ide/core.c:2027
#10 0x556a187d71c5 in handle_reg_h2d_fis hw/ide/ahci.c:1204
#11 0x556a187d7681 in handle_cmd hw/ide/ahci.c:1254
#12 0x556a187d168a in check_cmd hw/ide/ahci.c:510
#13 0x556a187d0afc in ahci_port_write hw/ide/ahci.c:314
#14 0x556a187d105d in ahci_mem_write hw/ide/ahci.c:435
#15 0x556a1831d959 in memory_region_write_accessor /home/elmarco/src/qemu/memory.c:525
#16 0x556a1831dc35 in access_with_adjusted_size /home/elmarco/src/qemu/memory.c:591
#17 0x556a18323ce3 in memory_region_dispatch_write /home/elmarco/src/qemu/memory.c:1262
#18 0x556a1828cf67 in address_space_write_continue /home/elmarco/src/qemu/exec.c:2578
#19 0x556a1828d20b in address_space_write /home/elmarco/src/qemu/exec.c:2635
#20 0x556a1828d92b in address_space_rw /home/elmarco/src/qemu/exec.c:2737
#21 0x556a1828daf7 in cpu_physical_memory_rw /home/elmarco/src/qemu/exec.c:2746
#22 0x556a183068d3 in cpu_physical_memory_write /home/elmarco/src/qemu/include/exec/cpu-common.h:72
#23 0x556a18308194 in qtest_process_command /home/elmarco/src/qemu/qtest.c:382
#24 0x556a18309999 in qtest_process_inbuf /home/elmarco/src/qemu/qtest.c:573
#25 0x556a18309a4a in qtest_read /home/elmarco/src/qemu/qtest.c:585
#26 0x556a18598b85 in qemu_chr_be_write_impl /home/elmarco/src/qemu/qemu-char.c:387
#27 0x556a18598c52 in qemu_chr_be_write /home/elmarco/src/qemu/qemu-char.c:399
#28 0x556a185a2afa in tcp_chr_read /home/elmarco/src/qemu/qemu-char.c:2902
#29 0x556a18cbaf52 in qio_channel_fd_source_dispatch io/channel-watch.c:84
Follow John Snow recommendation:
Everywhere else ncq_err is used, it is accompanied by a list cleanup
except for ncq_cb, which is the case you are fixing here.
Move the sglist destruction inside of ncq_err and then delete it from
the other two locations to keep it tidy.
Call dma_buf_commit in ide_dma_cb after the early return. Though, this
is also a little wonky because this routine does more than clear the
list, but it is at the moment the centralized "we're done with the
sglist" function and none of the other side effects that occur in
dma_buf_commit will interfere with the reset that occurs from
ide_restart_bh, I think
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
If one attempts to perform a system_reset after a failed IO request
that causes the VM to enter a paused state, QEMU will segfault trying
to free up the pending IO requests.
These requests have already been completed and freed, though, so all
we need to do is NULL them before we enter the paused state.
Existing AHCI tests verify that halted requests are still resumed
successfully after a STOP event.
Analyzed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Message-id: 1469635201-11918-2-git-send-email-jsnow@redhat.com
Signed-off-by: John Snow <jsnow@redhat.com>
Change sector-based blk_discard(), blk_co_discard(), and
blk_aio_discard() to instead be byte-based blk_pdiscard(),
blk_co_pdiscard(), and blk_aio_pdiscard(). NBD gets a lot
simpler now that ignoring the unaligned portion of a
byte-based discard request is handled under the hood by
the block layer.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1468624988-423-6-git-send-email-eblake@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
The following sequence of tests discovered a problem in IDE emulation:
1. Send DMA write to IDE device 0
2. Send CMD_FLUSH_CACHE to same IDE device which will be failed by block
layer using blkdebug script in tests/ide-test:test_retry_flush
When doing DMA request ide/core.c will set s->retry_unit to s->unit in
ide_start_dma. When dma completes ide_set_inactive sets retry_unit to -1.
After that ide_flush_cache runs and fails thanks to blkdebug.
ide_flush_cb calls ide_handle_rw_error which asserts that s->retry_unit
== s->unit. But s->retry_unit is still -1 after previous DMA completion
and flush does not use anything related to retry.
This patch restricts retry unit assertion only to ops that actually use
retry logic.
Signed-off-by: Evgeny Yakovlev <eyakovlev@virtuozzo.com>
Signed-off-by: Denis V. Lunev <den@openvz.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-id: 1468870792-7411-3-git-send-email-den@openvz.org
CC: Kevin Wolf <kwolf@redhat.com>
CC: Max Reitz <mreitz@redhat.com>
CC: Stefan Hajnoczi <stefanha@redhat.com>
CC: Fam Zheng <famz@redhat.com>
CC: John Snow <jsnow@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Code to set and clear state associated with retry in moved into
ide_set_retry and ide_clear_retry to make adding retry setups easier.
Signed-off-by: Evgeny Yakovlev <eyakovlev@virtuozzo.com>
Signed-off-by: Denis V. Lunev <den@openvz.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-id: 1468870792-7411-2-git-send-email-den@openvz.org
CC: Kevin Wolf <kwolf@redhat.com>
CC: Max Reitz <mreitz@redhat.com>
CC: Stefan Hajnoczi <stefanha@redhat.com>
CC: Fam Zheng <famz@redhat.com>
CC: John Snow <jsnow@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Tracked down with an ugly, brittle and probably buggy Perl script.
Also move includes converted to <...> up so they get included before
ours where that's obviously okay.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Tested-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Callers of dma_blk_io have no way to pass extra data to the DMAIOFunc,
because the original callback and opaque are gone by the time DMAIOFunc
is called. On the other hand, the BlockBackend is usually derived
from those extra data that you could pass to the DMAIOFunc (in the
next patch, that would be the SCSIRequest).
So change DMAIOFunc's prototype, decoupling it from blk_aio_readv
and blk_aio_writev's. The new prototype loses the BlockBackend
and gains an extra opaque value which, in the case of dma_blk_readv
and dma_blk_writev, is of course used for the BlockBackend.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Sector-based blk_aio_readv() and blk_aio_writev() should die; switch
to byte-based blk_aio_preadv() and blk_aio_pwritev() instead.
The patch had to touch multiple files at once, because dma_blk_io()
takes pointers to the functions, and ide_issue_trim() piggybacks on
the same interface (while ignoring offset under the hood).
Signed-off-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Restart of ATAPI DMA used to be unreachable, because the request to do
so wasn't indicated in bus->error_status due to the lack of spare bits, and
ide_restart_bh() would return early doing nothing.
This patch makes use of the observation that not all bit combinations were
possible in ->error_status. In particular, IDE_RETRY_READ only made sense
together with IDE_RETRY_DMA or IDE_RETRY_PIO. This allows to re-use
IDE_RETRY_READ alone as an indicator of ATAPI DMA restart request.
To makes things more uniform, ATAPI DMA gets its own value for ->dma_cmd.
As a means against confusion, macros are added to test the state of
->error_status.
The patch fixes the restart of both in-flight and pending ATAPI DMA,
following the scheme similar to that of IDE DMA.
[Including a fixup patch:
Message-id: 1460465594-15777-1-git-send-email-pbutsykin@virtuozzo.com
--js]
Signed-off-by: Pavel Butsykin <pbutsykin@virtuozzo.com>
Signed-off-by: Denis V. Lunev <den@openvz.org>
Reviewed-by: Roman Kagan <rkagan@virtuozzo.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Message-id: 1459924806-306-4-git-send-email-den@openvz.org
Signed-off-by: John Snow <jsnow@redhat.com>
If the migration occurs after the IDE DMA has been set up but before it
has been initiated, the state gets lost upon save/restore. Specifically,
->dma_cb callback gets cleared, so, when the guest eventually starts bus
mastering, the DMA never completes, causing the guest to time out the
operation.
OTOH all the infrastructure is already in place to restart the DMA if
the migration happens while the DMA is in progress.
So reuse that infrastructure, by setting bus->error_status based on
->dma_cmd in pre_save if ->dma_cb callback is already set but DMAING is
clear. This will indicate the need for restart and make sure ->dma_cb
is restored in ide_restart_bh(); howeover since DMAING is clear the state
upon restore will be exactly "ready for DMA" as before the save.
Signed-off-by: Pavel Butsykin <pbutsykin@virtuozzo.com>
Reviewed-by: Roman Kagan <rkagan@virtuozzo.com>
Signed-off-by: Denis V. Lunev <den@openvz.org>
Reviewed-by: John Snow <jsnow@redhat.com>
Message-id: 1459924806-306-2-git-send-email-den@openvz.org
Signed-off-by: John Snow <jsnow@redhat.com>
Move declarations out of qemu-common.h for functions declared in
utils/ files: e.g. include/qemu/path.h for utils/path.c.
Move inline functions out of qemu-common.h and into new files (e.g.
include/qemu/bcd.h)
Signed-off-by: Veronia Bahaa <veroniabahaa@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch replaces get_ticks_per_sec() calls with the macro
NANOSECONDS_PER_SECOND. Also, as there are no callers, get_ticks_per_sec()
is then removed. This replacement improves the readability and
understandability of code.
For example,
timer_mod(fdctrl->result_timer,
qemu_clock_get_ns(QEMU_CLOCK_VIRTUAL) + (get_ticks_per_sec() / 50));
NANOSECONDS_PER_SECOND makes it obvious that qemu_clock_get_ns
matches the unit of the expression on the right side of the plus.
Signed-off-by: Rutuja Shah <rutu.shah.26@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Reported-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1453225191-11871-7-git-send-email-jsnow@redhat.com
Split apart the ide_transfer_stop function into two versions: one that
interrupts and one that doesn't. The one that doesn't can be used to
halt any PIO transfers that are in the DRQ phase. It will not halt
any PIO transfers that are currently in the process of buffering data
for the guest to read.
Signed-off-by: John Snow <jsnow@redhat.com>
Reported-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
[Renamed 'etf' to 'end_transfer_func' --js]
Message-id: 1453225191-11871-6-git-send-email-jsnow@redhat.com
Target the drain for just one device.
Signed-off-by: John Snow <jsnow@redhat.com>
Reported-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1453225191-11871-5-git-send-email-jsnow@redhat.com
Buffered DMA cancellation was added to ATAPI devices and implemented
for the BMDMA HBA. Move the code over to common IDE code and allow
it to be used for any HBA.
Signed-off-by: John Snow <jsnow@redhat.com>
Reported-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1453225191-11871-4-git-send-email-jsnow@redhat.com
Shuffle the reset function upwards.
Signed-off-by: John Snow <jsnow@redhat.com>
Reported-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1453225191-11871-3-git-send-email-jsnow@redhat.com
This command is meant for ATAPI devices only, prohibit acknowledging it with
a command aborted response when an IDE device is busy.
Signed-off-by: John Snow <jsnow@redhat.com>
Reported-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1453225191-11871-2-git-send-email-jsnow@redhat.com
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1453832250-766-17-git-send-email-peter.maydell@linaro.org
this patch adds a new aio readv compatible function which copies
all data through a bounce buffer. These buffered requests can be
flagged as orphaned which means that their original callback has
already been invoked and the request has just not been completed
by the backend storage. The bounce buffer guarantees that guest
memory corruption is avoided when such a orphaned request is
completed by the backend at a later stage.
This trick only works for read requests as a write request completed
at a later stage might corrupt data as there is no way to control
if and what data has already been written to the storage.
Signed-off-by: Peter Lieven <pl@kamp.de>
Reviewed-by: Fam Zheng <famz@redhat.com>
Message-id: 1447345846-15624-4-git-send-email-pl@kamp.de
Signed-off-by: John Snow <jsnow@redhat.com>
This makes the purpose of the function clearer: it is not about the
version of QEMU that's running, but the version string exposed in the
emulated hardware.
Cc: Andrzej Zaborowski <balrogg@gmail.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: John Snow <jsnow@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <1446233769-7892-3-git-send-email-ehabkost@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
We're supposed to abort on transfers like this, unless we fill
Word 125 of our IDENTIFY data with a default transfer size, which
we don't currently do.
This is an ATA error, not a SCSI/ATAPI one.
See ATA8-ACS3 sections 7.17.6.49 or 7.21.5.
If we don't do this, QEMU will loop forever trying to transfer
zero bytes, which isn't particularly useful.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Message-id: 1442253685-23349-2-git-send-email-jsnow@redhat.com
We're a little too lenient with what we'll let an ATAPI drive handle.
Clamp down on the IDE command execution table to remove CD_OK permissions
from commands that are not and have never been ATAPI commands.
For ATAPI command validity, please see:
- ATA4 Section 6.5 ("PACKET Command feature set")
- ATA8/ACS Section 4.3 ("The PACKET feature set")
- ACS3 Section 4.3 ("The PACKET feature set")
ACS3 has a historical command validity table in Table B.4
("Historical Command Assignments") that can be referenced to find when
a command was introduced, deprecated, obsoleted, etc.
The only reference for ATAPI command validity is by checking that
version's PACKET feature set section.
ATAPI was introduced by T13 into ATA4, all commands retired prior to ATA4
therefore are assumed to have never been ATAPI commands.
Mandatory commands, as listed in ATA8-ACS3, are:
- DEVICE RESET
- EXECUTE DEVICE DIAGNOSTIC
- IDENTIFY DEVICE
- IDENTIFY PACKET DEVICE
- NOP
- PACKET
- READ SECTOR(S)
- SET FEATURES
Optional commands as listed in ATA8-ACS3, are:
- FLUSH CACHE
- READ LOG DMA EXT
- READ LOG EXT
- WRITE LOG DMA EXT
- WRITE LOG EXT
All other commands are illegal to send to an ATAPI device and should
be rejected by the device.
CD_OK removal justifications:
0x06 WIN_DSM Defined in ACS2. Not valid for ATAPI.
0x21 WIN_READ_ONCE Retired in ATA5. Not ATAPI in ATA4.
0x94 WIN_STANDBYNOW2 Retired in ATA4. Did not coexist with ATAPI.
0x95 WIN_IDLEIMMEDIATE2 Retired in ATA4. Did not coexist with ATAPI.
0x96 WIN_STANDBY2 Retired in ATA4. Did not coexist with ATAPI.
0x97 WIN_SETIDLE2 Retired in ATA4. Did not coexist with ATAPI.
0x98 WIN_CHECKPOWERMODE2 Retired in ATA4. Did not coexist with ATAPI.
0x99 WIN_SLEEPNOW2 Retired in ATA4. Did not coexist with ATAPI.
0xE0 WIN_STANDBYNOW1 Not part of ATAPI in ATA4, ACS or ACS3.
0xE1 WIN_IDLEIMMDIATE Not part of ATAPI in ATA4, ACS or ACS3.
0xE2 WIN_STANDBY Not part of ATAPI in ATA4, ACS or ACS3.
0xE3 WIN_SETIDLE1 Not part of ATAPI in ATA4, ACS or ACS3.
0xE4 WIN_CHECKPOWERMODE1 Not part of ATAPI in ATA4, ACS or ACS3.
0xE5 WIN_SLEEPNOW1 Not part of ATAPI in ATA4, ACS or ACS3.
0xF8 WIN_READ_NATIVE_MAX Obsoleted in ACS3. Not ATAPI in ATA4 or ACS.
This patch fixes a divide by zero fault that can be caused by sending
the WIN_READ_NATIVE_MAX command to an ATAPI drive, which causes it to
attempt to use zeroed CHS values to perform sector arithmetic.
Reported-by: Qinghao Tang <luodalongde@gmail.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Message-id: 1441816082-21031-1-git-send-email-jsnow@redhat.com
CC: qemu-stable@nongnu.org
IDEState's io_buffer_offset was originally added to keep track of offsets
in AHCI rather exclusively, but it was added to IDEState instead of an
AHCI-specific structure.
AHCI fakes all PIO transfers using DMA and a scatter-gather list. When
the core or atapi layers invoke HBA-specific mechanisms for transfers,
they do not always know that it is being backed by DMA or a sglist, so
this offset is not always updated by the HBA code everywhere.
If we modify it in dma_buf_commit, however, any HBA that needs to use
this offset to manage operating on only part of a sglist will have
access to it.
This will fix ATAPI PIO transfers performed through the AHCI HBA,
which were previously not modifying this value appropriately.
This will fix ATAPI PIO transfers larger than one sector.
Reported-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
Message-id: 1440546331-29087-2-git-send-email-jsnow@redhat.com
CC: qemu-stable@nongnu.org
This is additional hardening against an end_transfer_func that fails to
clear the DRQ status bit. The bit must be unset as soon as the PIO
transfer has completed, so it's better to do this in a central place
instead of duplicating the code in all commands (and forgetting it in
some).
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
If the end_transfer_func of a command is called because enough data has
been read or written for the current PIO transfer, and it fails to
correctly call the command completion functions, the DRQ bit in the
status register and s->end_transfer_func may remain set. This allows the
guest to access further bytes in s->io_buffer beyond s->data_end, and
eventually overflowing the io_buffer.
One case where this currently happens is emulation of the ATAPI command
START STOP UNIT.
This patch fixes the problem by adding explicit array bounds checks
before accessing the buffer instead of relying on end_transfer_func to
function correctly.
Cc: qemu-stable@nongnu.org
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Handle NCQ failures for cases where we want to halt the VM on IO errors.
Upon a VM state change, retry the halted NCQ commands.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1435767578-32743-7-git-send-email-jsnow@redhat.com
prepare_buf should not always grab as many descriptors
as it can, sometimes it should self-limit.
For example, an NCQ transfer of 1 sector with a PRDT that
describes 4GiB of data should not copy 4GiB of data, it
should just transfer that first 512 bytes.
PIO is not affected, because the dma_buf_rw dma helpers
already have a byte limit built-in to them, but DMA/NCQ
will exhaust the entire list regardless of requested size.
AHCI 1.3 specifies in section 6.1.6 Command List Underflow that
NCQ is not required to detect underflow conditions. Non-NCQ
pathways signal underflow by writing to the PRDBC field, which
will already occur by writing the actual transferred byte count
to the PRDBC, signaling the underflow.
Our NCQ pathways aren't required to detect underflow, but since our DMA
backend uses the size of the PRDT to determine the size of the transer,
if our PRDT is bigger than the transaction (the underflow condition) it
doesn't cost us anything to detect it and truncate the PRDT.
This is a recoverable error and is not signaled to the guest, in either
NCQ or normal DMA cases.
For BMDMA, the existing pathways should see no guest-visible difference,
but any bytes described in the overage will no longer be transferred
before indicating to the guest that there was an underflow.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1435767578-32743-2-git-send-email-jsnow@redhat.com
We create optional sections with this patch. But we already have
optional subsections. Instead of having two mechanism that do the
same, we can just generalize it.
For subsections we just change:
- Add a needed function to VMStateDescription
- Remove VMStateSubsection (after removal of the needed function
it is just a VMStateDescription)
- Adjust the whole tree, moving the needed function to the corresponding
VMStateDescription
Signed-off-by: Juan Quintela <quintela@redhat.com>
IDE PIO data must be written, for example, at 0x1f0. You cannot
do word or dword writes to 0x1f1..0x1f3 to access the data register.
Adjust the ide_portio_list accordingly.
Cc: John Snow <jsnow@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Similar to the cmd_write_pio fix, update the nsector count and
ide sector before we invoke ide_transfer_start.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Tested-by: Andreas Färber <afaerber@suse.de>
Message-id: 1426811056-2202-3-git-send-email-jsnow@redhat.com
We need to adjust the sector being written to
prior to calling ide_transfer_start, otherwise
we'll write to the same sector again.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Tested-by: Andreas Färber <afaerber@suse.de>
Message-id: 1426811056-2202-2-git-send-email-jsnow@redhat.com
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Message-id: 1424708286-16483-13-git-send-email-jsnow@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Resetting the io_buffer_index to 0 is commonized,
with the exception of the case within ide_atapi_cmd_reply,
where we need to reset this index to 0 prior to the
ide_atapi_cmd_reply_end call.
Note that not all calls to ide_atapi_cmd_reply_end
expect the index to be 0, so setting it there is
not appropriate.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Message-id: 1424708286-16483-12-git-send-email-jsnow@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This only breaks backwards migration compatibility if the bus is in
an error state. It is in principle possible to avoid this by making
two subsections (one for version 1, and one for version 2, but with
the same name) with different "_needed" callbacks. The v1 callback would
return true if error_status != 0 and the bus is PATA; the v2 callback
would return true if error_status != 0 and the bus is AHCI.
Forward migration keeps working.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Message-id: 1424708286-16483-11-git-send-email-jsnow@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This moves more common restarting logic to the core IDE code.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Message-id: 1424708286-16483-10-git-send-email-jsnow@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Start moving the initial state of the current request to IDEBus, so that
AHCI can use it. The set_unit callback is not used anymore once this is
done.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Message-id: 1424708286-16483-9-git-send-email-jsnow@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
With restarts now handled by ide_restart_cb and
the IDEDMAOps.restart_dma() member, remove the old
restart_cb callback.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Message-id: 1424708286-16483-8-git-send-email-jsnow@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
With BMDMA specific excised from the restart functions,
create a HBA-agnostic restart callback to be shared
between the different HBAs.
Change the callback registered with the vmstate_change
handler to always point to ide_restart_cb instead of
relying on the IDEDMAOps.restart_cb() member.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Message-id: 1424708286-16483-7-git-send-email-jsnow@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Pass the containing IDEBus to the restart_cb instead
of the more specific BMDMAState child.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Message-id: 1424708286-16483-6-git-send-email-jsnow@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
A helper is added that registers the IDEDMAOp .restart_cb()
via qemu_add_vm_change_state_handler instead of requiring
each HBA to register the callback themselves.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Message-id: 1424708286-16483-4-git-send-email-jsnow@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
If a migration happens just after the guest has kicked
off an ATAPI command and kicked off DMA, we lose the atapi_dma
flag, and the destination tries to complete the command as PIO
rather than DMA. This upsets Linux; modern libata based kernels
stumble and recover OK, older kernels end up passing bad data
to userspace.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The other callers to blk_set_enable_write_cache() in this file
already check for s->blk == NULL.
Signed-off-by: Don Slutz <dslutz@verizon.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1416259239-13281-1-git-send-email-dslutz@verizon.com
Cc: qemu-stable@nongnu.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This impacts both BMDMA and AHCI HBA interfaces for IDE.
Currently, we confuse the difference between a PRDT having
"0 bytes" and a PRDT having "0 complete sectors."
When we receive an incomplete sector, inconsistent error checking
leads to an infinite loop wherein the call succeeds, but it
didn't give us enough bytes -- leading us to re-call the
DMA chain over and over again. This leads to, in the BMDMA case,
leaked memory for short PRDTs, and infinite loops and resource
usage in the AHCI case.
The .prepare_buf() callback is reworked to return the number of
bytes that it successfully prepared. 0 is a valid, non-error
answer that means the table was empty and described no bytes.
-1 indicates an error.
Our current implementation uses the io_buffer in IDEState to
ultimately describe the size of a prepared scatter-gather list.
Even though the AHCI PRDT/SGList can be as large as 256GiB, the
AHCI command header limits transactions to just 4GiB. ATA8-ACS3,
however, defines the largest transaction to be an LBA48 command
that transfers 65,536 sectors. With a 512 byte sector size, this
is just 32MiB.
Since our current state structures use the int type to describe
the size of the buffer, and this state is migrated as int32, we
are limited to describing 2GiB buffer sizes unless we change the
migration protocol.
For this reason, this patch begins to unify the assertions in the
IDE pathways that the scatter-gather list provided by either the
AHCI PRDT or the PCI BMDMA PRDs can only describe, at a maximum,
2GiB. This should be resilient enough unless we need a sector
size that exceeds 32KiB.
Further, the likelihood of any guest operating system actually
attempting to transfer this much data in a single operation is
very slim.
To this end, the IDEState variables have been updated to more
explicitly clarify our maximum supported size. Callers to the
prepare_buf callback have been reworked to understand the new
return code, and all versions of the prepare_buf callback have
been adjusted accordingly.
Lastly, the ahci_populate_sglist helper, relied upon by the
AHCI implementation of .prepare_buf() as well as the PCI
implementation of the callback have had overflow assertions
added to help make clear the reasonings behind the various
type changes.
[Added %d -> %"PRId64" fix John sent because off_pos changed from int to
int64_t.
--Stefan]
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-id: 1414785819-26209-4-git-send-email-jsnow@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Currently, for emulated PIO transfers through the AHCI device,
any attempt made to request more than a single sector's worth
of data will result in the same sector being transferred over
and over.
For example, if we request 8 sectors via PIO READ SECTORS, the
AHCI device will give us the same sector eight times.
This patch adds offset tracking into the PIO pathways so that
we can fulfill these requests appropriately.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-id: 1414785819-26209-2-git-send-email-jsnow@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Currently, DMA read/write operations neglect to update
the byte count after a successful transfer like ATAPI
DMA read or PIO read/write operations do.
We correct this oversight by adding another callback into
the IDEDMAOps structure. The commit callback is called
whenever we are cleaning up a scatter-gather list.
AHCI can register this callback in order to update post-
transfer information such as byte count updates.
We use this callback in AHCI to consolidate where we delete
the SGlist as generated from the PRDT, as well as update the
byte count after the transfer is complete.
The QEMUSGList structure has an init flag added to it in order
to make qemu_sglist_destroy a nop if it is called when
there is no sglist, which simplifies cleanup and error paths.
This patch fixes several AHCI problems, notably Non-NCQ modes
of operation for Windows 7 as well as Hibernate support for Windows 7.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Tested-by: Michael S. Tsirkin <mst@redhat.com>
Message-id: 1412204151-18117-3-git-send-email-jsnow@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Add a BlockBackend member to TrimAIOCB, so ide_issue_trim_cb() can use
blk_aio_discard() instead of bdrv_aio_discard().
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Device models should access their block backends only through the
block-backend.h API. Convert them, and drop direct includes of
inappropriate headers.
Just four uses of BlockDriverState are left:
* The Xen paravirtual block device backend (xen_disk.c) opens images
itself when set up via xenbus, bypassing blockdev.c. I figure it
should go through qmp_blockdev_add() instead.
* Device model "usb-storage" prompts for keys. No other device model
does, and this one probably shouldn't do it, either.
* ide_issue_trim_cb() uses bdrv_aio_discard() instead of
blk_aio_discard() because it fishes its backend out of a BlockAIOCB,
which has only the BlockDriverState.
* PC87312State has an unused BlockDriverState[] member.
The next two commits take care of the latter two.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
I'll use it with block backends shortly, and the name is going to fit
badly there. It's a block layer thing anyway, not just a block driver
thing.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
I'll use BlockDriverAIOCB with block backends shortly, and the name is
going to fit badly there. It's a block layer thing anyway, not just a
block driver thing.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Instead of duplicating the logic for the if_ide
(bus,unit) mappings, rely on the blockdev layer
for managing those mappings for us, and use the
drive_get_by_index call instead.
This allows ide_drive_get to work for AHCI HBAs
as well, and can be used in the Q35 initialization.
Lastly, change the nature of the argument to
ide_drive_get so that represents the number of
total drives we can support, and not the total
number of buses. This will prevent array overflows
if the units-per-default-bus property ever needs
to be adjusted for compatibility reasons.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-id: 1412187569-23452-5-git-send-email-jsnow@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
We know that either bh is scheduled or ide_issue_trim_cb will be called
again, so we just set i, j and ret to the right values. In both cases,
ide_trim_bh_cb will be called.
Also forward the cancellation to the iocb->aiocb which we get from
bdrv_aio_discard.
Signed-off-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Before, bdrv_aio_cancel will either complete the request (like normal)
and call CB with an actual return code, or skip calling the request (for
example when the IO req is not submitted by thread pool yet).
We will change bdrv_aio_cancel to do it differently: always call CB
before return, with either [1] a normal req completion ret code, or [2]
ret == -ECANCELED. So the callers' callback must accept both cases. The
existing logic works with case [1], but not [2].
The simplest transition of callback code is do nothing in case [2], just
as if the CB is not called by the bdrv_aio_cancel() call.
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
This is the next step for decoupling block accounting functions from
BlockDriverState.
In a future commit the BlockAcctStats structure will be moved from
BlockDriverState to the device models structures.
Note that bdrv_get_stats was introduced so device models can retrieve the
BlockAcctStats structure of a BlockDriverState without being aware of it's
layout.
This function should go away when BlockAcctStats will be embedded in the device
models structures.
CC: Kevin Wolf <kwolf@redhat.com>
CC: Stefan Hajnoczi <stefanha@redhat.com>
CC: Keith Busch <keith.busch@intel.com>
CC: Anthony Liguori <aliguori@amazon.com>
CC: "Michael S. Tsirkin" <mst@redhat.com>
CC: Paolo Bonzini <pbonzini@redhat.com>
CC: Eric Blake <eblake@redhat.com>
CC: Peter Maydell <peter.maydell@linaro.org>
CC: Michael Tokarev <mjt@tls.msk.ru>
CC: John Snow <jsnow@redhat.com>
CC: Markus Armbruster <armbru@redhat.com>
CC: Alexander Graf <agraf@suse.de>
CC: Max Reitz <mreitz@redhat.com>
Signed-off-by: Benoît Canet <benoit.canet@nodalink.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The middle term goal is to move the BlockAcctStats structure in the device models.
(Capturing I/O accounting statistics in the device models is good for billing)
This patch make a small step in this direction by removing a reference to BDRV.
CC: Kevin Wolf <kwolf@redhat.com>
CC: Stefan Hajnoczi <stefanha@redhat.com>
CC: Keith Busch <keith.busch@intel.com>
CC: Anthony Liguori <aliguori@amazon.com>
CC: "Michael S. Tsirkin" <mst@redhat.com>
CC: Paolo Bonzini <pbonzini@redhat.com>
CC: John Snow <jsnow@redhat.com>
CC: Richard Henderson <rth@twiddle.net>
CC: Markus Armbruster <armbru@redhat.com>
CC: Alexander Graf <agraf@suse.de>i
Signed-off-by: Benoît Canet <benoit.canet@nodalink.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Currently, if the block device backing the IDE drive is resized,
the information about the device as cached inside of the IDEState
structure is not updated, thus when a guest OS re-queries the drive,
it is unable to see the expanded size.
This patch adds a resize callback that updates the IDENTIFY data
buffer in order to correct this.
Lastly, a Linux guest as-is cannot resize a libata drive while in-use,
but it can see the expanded size as part of a bus rescan event.
This patch also allows guests such as Linux to see the new drive size
after a soft reboot event, without having to exit the QEMU process.
Signed-off-by: John Snow <jsnow@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
IDE-HD, IDE-ATAPI and IDE-CFATA all fill the
identify buffer in slightly different ways,
this is a relatively minor patch to make them
uniform, to emphasize that:
(1) We build the s->identify_data cache first, then
(2) We copy it to s->io_buffer to fulfill the request.
Signed-off-by: John Snow <jsnow@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Although it is possible to specify the wwn
property for cdrom devices on the command line,
the underlying driver fails to relay this information
to the guest operating system via IDENTIFY.
This is a simple patch to correct that.
See ATA8-ACS, Table 22 parts 5, 6, and 9.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Commit 58ac321135 introduced a check to ide dma processing which
constrains all requests to drive size. However, apparently, some
valid requests (like TRIM) does not fit in this constraint, and
fails in 2.1. So check the range only for reads and writes.
Cc: qemu-stable@nongnu.org
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
AHCI has code to fill in the D2H FIS trigger the IRQ all over the place.
Centralize this in a single cmd_done callback by generalizing the existing
async_cmd_done callback.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
This will provide a hook for sending the result of the command via the
FIS receive area.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
It is now called only after the set_inactive callback. Put the two together.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Make it optional and prepare for the next patches.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Drop the unused return value and make the callback optional.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Drop the unused return value and make the callback optional.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Drop the unused return value and make the callback optional.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
This ensures that operations are completed after a reset
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
The block layer fails such reads and writes just fine. However, they
then get treated like valid operations that fail: the error action
gets executed. Unwanted; reporting the error to the guest is the only
sensible action.
Reject them before passing them to the block layer. This bypasses the
error action and I/O accounting. Not quite correct for DMA, because
DMA can fail after some success, and when that happens, the part that
succeeded isn't counted. Tolerable, because I/O accounting is an
inconsistent mess anyway.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
In order to let event defines use existing types later, instead of
redefine new ones, some old type defines for spice and vnc are changed,
and BlockErrorAction is moved from block.h to qapi schema. Note that
BlockErrorAction is not merged with BlockdevOnError.
At this point, VncInfo is not made a child of VncBasicInfo, because
VncBasicInfo has mandatory fields where VncInfo makes them optional.
Signed-off-by: Wenchao Xia <wenchaoqemu@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
After previous Peter patch, they are redundant. This way we don't
assign them except when needed. Once there, there were lots of case
where the ".fields" indentation was wrong:
.fields = (VMStateField []) {
and
.fields = (VMStateField []) {
Change all the combinations to:
.fields = (VMStateField[]){
The biggest problem (appart from aesthetics) was that checkpatch complained
when we copy&pasted the code from one place to another.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
The SMART self test counter was incorrectly being reset to zero,
not 1. This had the effect that on every 21st SMART EXECUTE OFFLINE:
* We would write off the beginning of a dynamically allocated buffer
* We forgot the SMART history
Fix this.
Signed-off-by: Benoit Canet <benoit@irqsave.net>
Message-id: 1397336390-24664-1-git-send-email-benoit.canet@irqsave.net
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Cc: qemu-stable@nongnu.org
Acked-by: Kevin Wolf <kwolf@redhat.com>
[PMM: tweaked commit message as per suggestions from Markus]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The alignment field is now set to the value that is promised to the
guest, rather than required by the host. The next patches will make
QEMU aware of the host-provided values, so make this clear.
The alignment is also not about memory buffers, but about the sectors on
the disk, change the documentation of the field.
At this point, the field is set by the device emulation, but completely
ignored by the block layer.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Wenchao Xia <xiawenc@linux.vnet.ibm.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Benoit Canet <benoit@irqsave.net>
This notably fix IDE CD probing on the Plan 9 operating system,
which rely on the error register set by the Execute Device
Diagnostic command to detect drive configurations.
Thanks to Rémi Pommarel for reporting this issue.
Signed-off-by: David du Colombier <0intro@gmail.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
This is an autogenerated patch using scripts/switch-timer-api.
Switch the entire code base to using the new timer API.
Note this patch may introduce some line length issues.
Signed-off-by: Alex Bligh <alex@alex.org.uk>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
AHCI couldn't cope with asynchronous commands that aren't doing DMA, it
simply wouldn't complete them. Due to the bug fixed in commit f68ec837,
FLUSH commands would seem to have completed immediately even if they
were still running on the host. After the commit, they would simply hang
and never unset the BSY bit, rendering AHCI unusable on any OS sending
flushes.
This patch adds another callback for the completion of asynchronous
commands. This is what AHCI really wants to use for its command
completion logic rather than an DMA completion callback.
Cc: qemu-stable@nongnu.org
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
All commands are now converted to ide_cmd_table handlers, so it can be
unconditional now and the old switch block can go.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
John Snow
Mao Zhongyi
Stefan Hajnoczi
Li Qiang
Kevin Wolf
Markus Armbruster
Mark Cave-Ayland
Ashijeet Acharya
Marc-André Lureau
Eric Blake
Evgeny Yakovlev
Paolo Bonzini
Pavel Butsykin
Veronia Bahaa
Rutuja Shah
Peter Maydell
Peter Lieven
Alberto Garcia
Eduardo Habkost
Juan Quintela
Dr. David Alan Gilbert
Don Slutz
Fam Zheng
Benoît Canet
Michael Tokarev
Wenchao Xia
Benoît Canet
David du Colombier
Andreas Färber
Alex Bligh