It is possible to have another VLAN tag even if the packet is already
tagged.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
The uses of uint8_t pointers were misleading as they are never accessed
as an array of octets and it even require more strict alignment to
access as struct eth_header.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Section 13.7.15 Receive Length Error Count says:
> Packets over 1522 bytes are oversized if LongPacketEnable is 0b
> (RCTL.LPE). If LongPacketEnable (LPE) is 1b, then an incoming packet
> is considered oversized if it exceeds 16384 bytes.
> These lengths are based on bytes in the received packet from
> <Destination Address> through <CRC>, inclusively.
As QEMU processes packets without CRC, the number of bytes for CRC
need to be subtracted. This change adds some size definitions to be used
to derive the new size thresholds to eth.h.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
The old eth_setup_vlan_headers has no user so remove it and rename
eth_setup_vlan_headers_ex.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Jason Wang <jasowang@redhat.com>
igb does not properly ensure the buffer passed to
net_rx_pkt_set_protocols() is contiguous for the entire L2/L3/L4 header.
Allow it to pass scattered data to net_rx_pkt_set_protocols().
Fixes: 3a977deebe ("Intrdocue igb device emulation")
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Sriram Yagnaraman <sriram.yagnaraman@est.tech>
Signed-off-by: Jason Wang <jasowang@redhat.com>
igb, a new network device emulation, will need SCTP checksum offloading.
Currently eth_get_protocols() has a bool parameter for each protocol
currently it supports, but there will be a bit too many parameters if
we add yet another protocol.
Introduce an enum type, EthL4HdrProto to represent all L4 protocols
eth_get_protocols() support with one parameter.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
The values returned by eth_get_protocols() are used to perform RSS,
checksumming and segmentation. Even when a packet signals the use of the
protocols which these operations can be applied to, the headers for them
may not be present because of too short packet or fragmentation, for
example. In such a case, the operations cannot be applied safely.
Report the presence of headers instead of whether the use of the
protocols are indicated with eth_get_protocols(). This also makes
corresponding changes to the callers of eth_get_protocols() to match
with its new signature and to remove redundant checks for fragmentation.
Fixes: 75020a7021 ("Common definitions for VMWARE devices")
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
There was no proper implementation of TCP segmentation before this
change, and net_tx_pkt relied solely on IPv4 fragmentation. Not only
this is not aligned with the specification, but it also resulted in
corrupted IPv6 packets.
This is particularly problematic for the igb, a new proposed device
implementation; igb provides loopback feature for VMDq and the feature
relies on software segmentation.
Implement proper TCP segmentation in net_tx_pkt to fix such a scenario.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Replace a config-time define with a compile time condition
define (compatible with clang and gcc) that must be declared prior to
its usage. This avoids having a global configure time define, but also
prevents from bad usage, if the config header wasn't included before.
This can help to make some code independent from qemu too.
gcc supports __BYTE_ORDER__ from about 4.6 and clang from 3.2.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
[ For the s390x parts I'm involved in ]
Acked-by: Halil Pasic <pasic@linux.ibm.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20220323155743.1585078-7-marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add a helper to pad a short Ethernet frame to the minimum required
length, which can be used by backends' code.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Buglink: https://bugzilla.redhat.com/show_bug.cgi?id=1708065
With network backend with 'virtual header' - there was an issue
in 'plen' field. Overall, during TSO, 'plen' would be changed,
but with 'vheader' this field should be set to the size of the
payload itself instead of '0'.
Signed-off-by: Andrew Melnychenko <andrew@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
This commit adds implementation of RX packets
coalescing, compatible with requirements of Windows
Hardware compatibility kit.
The device enables feature VIRTIO_NET_F_RSC_EXT in
host features if it supports extended RSC functionality
as defined in the specification.
This feature requires at least one of VIRTIO_NET_F_GUEST_TSO4,
VIRTIO_NET_F_GUEST_TSO6. Windows guest driver acks
this feature only if VIRTIO_NET_F_CTRL_GUEST_OFFLOADS
is also present.
If the guest driver acks VIRTIO_NET_F_RSC_EXT feature,
the device coalesces TCPv4 and TCPv6 packets (if
respective VIRTIO_NET_F_GUEST_TSO feature is on,
populates extended RSC information in virtio header
and sets VIRTIO_NET_HDR_F_RSC_INFO bit in header flags.
The device does not recalculate checksums in the coalesced
packet, so they are not valid.
In this case:
All the data packets in a tcp connection are cached
to a single buffer in every receive interval, and will
be sent out via a timer, the 'virtio_net_rsc_timeout'
controls the interval, this value may impact the
performance and response time of tcp connection,
50000(50us) is an experience value to gain a performance
improvement, since the whql test sends packets every 100us,
so '300000(300us)' passes the test case, it is the default
value as well, tune it via the command line parameter
'rsc_interval' within 'virtio-net-pci' device, for example,
to launch a guest with interval set as '500000':
'virtio-net-pci,netdev=hostnet1,bus=pci.0,id=net1,mac=00,
guest_rsc_ext=on,rsc_interval=500000'
The timer will only be triggered if the packets pool is not empty,
and it'll drain off all the cached packets.
'NetRscChain' is used to save the segments of IPv4/6 in a
VirtIONet device.
A new segment becomes a 'Candidate' as well as it passed sanity check,
the main handler of TCP includes TCP window update, duplicated
ACK check and the real data coalescing.
An 'Candidate' segment means:
1. Segment is within current window and the sequence is the expected one.
2. 'ACK' of the segment is in the valid window.
Sanity check includes:
1. Incorrect version in IP header
2. An IP options or IP fragment
3. Not a TCP packet
4. Sanity size check to prevent buffer overflow attack.
5. An ECN packet
Even though, there might more cases should be considered such as
ip identification other flags, while it breaks the test because
windows set it to the same even it's not a fragment.
Normally it includes 2 typical ways to handle a TCP control flag,
'bypass' and 'finalize', 'bypass' means should be sent out directly,
while 'finalize' means the packets should also be bypassed, but this
should be done after search for the same connection packets in the
pool and drain all of them out, this is to avoid out of order fragment.
All the 'SYN' packets will be bypassed since this always begin a new'
connection, other flags such 'URG/FIN/RST/CWR/ECE' will trigger a
finalization, because this normally happens upon a connection is going
to be closed, an 'URG' packet also finalize current coalescing unit.
Statistics can be used to monitor the basic coalescing status, the
'out of order' and 'out of window' means how many retransmitting packets,
thus describe the performance intuitively.
Difference between ip v4 and v6 processing:
Fragment length in ipv4 header includes itself, while it's not
included for ipv6, thus means ipv6 can carry a real 65535 payload.
Note that main goal of implementing this feature in software
is to create reference setup for certification tests. In such
setups guest migration is not required, so the coalesced packets
not yet delivered to the guest will be lost in case of migration.
Signed-off-by: Wei Xu <wexu@redhat.com>
Signed-off-by: Yuri Benditovich <yuri.benditovich@daynix.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
NC-SI (Network Controller Sideband Interface) enables a BMC to manage
a set of NICs on a system. This model takes the simplest approach and
reverses the NC-SI packets to pretend a NIC is present and exercise
the Linux driver.
The NCSI header file <ncsi-pkt.h> comes from mainline Linux and was
untabified.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Make VLAN stripping functions return number of bytes
copied to given Ethernet header buffer.
This information should be used to re-compose
packet IOV after VLAN stripping.
Cc: qemu-stable@nongnu.org
Signed-off-by: Dmitry Fleytman <dmitry@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
This patch extends the TX/RX packet abstractions with features that will
be used by the e1000e device implementation.
Changes are:
1. Support iovec lists for RX buffers
2. Deeper RX packets parsing
3. Loopback option for TX packets
4. Extended VLAN headers handling
5. RSS processing for RX packets
Signed-off-by: Dmitry Fleytman <dmitry.fleytman@ravellosystems.com>
Signed-off-by: Leonid Bloch <leonid.bloch@ravellosystems.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Dmitry Fleytman <dmitry.fleytman@ravellosystems.com>
Signed-off-by: Leonid Bloch <leonid.bloch@ravellosystems.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
NB: If this commit breaks compilation for your out-of-tree
patchseries or fork, then you need to make sure you add
#include "qemu/osdep.h" to any new .c files that you have.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Eric Blake <eblake@redhat.com>
eth.h and slirp.h both define ETH_ALEN and ETH_P_IP
rtl8139.c and eth.h both define ETH_HLEN
Move the related constant (ETH_P_ARP) from slirp.h to eth.h, and
remove the duplicates; make slirp.h include eth.h
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Jason Wang <jasowang@redhat.com>
[Assigning a multicast MAC address to a NIC leads to confusing behavior.
Reject multicast MAC addresses so users are alerted to their error
straight away.
The "net/eth.h" in6_addr rename prevents a name collision with
<netinet/in.h> on Linux.
-- Stefan]
Signed-off-by: Dmitry V. Krivenok <krivenok.dmitry@gmail.com>
Reviewed-by: Amos Kong <kongjianjun@gmail.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Akihiko Odaki
Marc-André Lureau
Bin Meng
Andrew
Yuri Benditovich
Cédric Le Goater
Dmitry Fleytman
Dmitry Fleytman
Peter Maydell
Dr. David Alan Gilbert
Dmitry Krivenok