This operation performs d = (b & a) | (c & ~a), and is present
on a majority of host vector units. Include gvec expanders.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
The paths through tcg_gen_dup_mem_vec and through MO_128 were
missing the check_size_align. The path through MO_128 was also
missing the expand_clr. This last was not visible because the
only user is ARM SVE, which would set oprsz == maxsz, and not
require the clear.
Fix by adding the check_size_align and using do_dup directly
instead of duplicating the check in tcg_gen_gvec_dup_{i32,i64}.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Allow expansion either via shift by scalar or by replicating
the scalar for shift by vector.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
---
v3: Use a private structure for do_gvec_shifts.
The gvec expanders perform a modulo on the shift count. If the target
requires alternate behaviour, then it cannot use the generic gvec
expanders anyway, and will have to have its own custom code.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Allow the backend to expand dup from memory directly, instead of
forcing the value into a temp first. This is especially important
if integer/vector register moves do not exist.
Note that officially tcg_out_dupm_vec is allowed to fail.
If it did, we could fix this up relatively easily:
VECE == 32/64:
Load the value into a vector register, then dup.
Both of these must work.
VECE == 8/16:
If the value happens to be at an offset such that an aligned
load would place the desired value in the least significant
end of the register, go ahead and load w/garbage in high bits.
Load the value w/INDEX_op_ld{8,16}_i32.
Attempt a move directly to vector reg, which may fail.
Store the value into the backing store for OTS.
Load the value into the vector reg w/TCG_TYPE_I32, which must work.
Duplicate from the vector reg into itself, which must work.
All of which is well and good, except that all supported
hosts can support dupm for all vece, so all of the failure
paths would be dead code and untestable.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Replace the single opcode in .opc with a null-terminated
array in .opt_opc. We still require that all opcodes be
used with the same .vece.
Validate the contents of this list with CONFIG_DEBUG_TCG.
All tcg_gen_*_vec functions will check any list active
during .fniv expansion. Swap the active list in and out
as we expand other opcodes, or take control away from the
front-end function.
Convert all existing vector aware front ends.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Let's add tcg_gen_gvec_3i(), similar to tcg_gen_gvec_2i(), however
without introducing "gen_helper_gvec_3i *fnoi", as it isn't needed
for now.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20190416185301.25344-2-david@redhat.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
It's either "GNU *Library* General Public version 2" or "GNU Lesser
General Public version *2.1*", but there was no "version 2.0" of the
"Lesser" library. So assume that version 2.1 is meant here.
Cc: Richard Henderson <rth@twiddle.net>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <1548252536-6242-5-git-send-email-thuth@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
We handle many of these during integer expansion, and the
rest of them during integer optimization.
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Normally this is automatic in the size restrictions that are placed
on vector sizes coming from the implementation. However, for the
legitimate size tuple [oprsz=8, maxsz=32], we need to clear the final
24 bytes of the vector register. Without this check, do_dup selects
TCG_TYPE_V128 and clears only 16 bytes.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Tested-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20180705191929.30773-2-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This unifies 5 copies of checks for supported vector size,
and in the process fixes a missing check in tcg_gen_gvec_2s.
This lead to an assertion failure for 64-bit vector multiply,
which is not available in the AVX instruction set.
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Use dup to convert a non-constant scalar to a third vector.
Add addition, multiplication, and logical operations with an immediate.
Add addition, subtraction, multiplication, and logical operations with
a non-constant scalar. Allow for the front-end to build operations in
which the scalar operand comes first.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
No vector ops as yet. SSE only has direct support for 8- and 16-bit
saturation; handling 32- and 64-bit saturation is much more expensive.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Opcodes are added for scalar and vector shifts, but considering the
varied semantics of these do not expose them to the front ends. Do
go ahead and provide them in case they are needed for backend expansion.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
