The size of the accessible iommu memory region in the guest
is given to the IOMMU by the guest through the mpcifc request
specifying the PCI Base Address and the PCI Address Limit.
Let's set the size of the IOMMU region to:
(PCI Address Limit) - (PCI Base Address) + 1.
Fixes: f7c40aa1e7 ("s390x/pci: fix failures of dma map/unmap")
Signed-off-by: Pierre Morel <pmorel@linux.ibm.com>
Message-Id: <1547125207-16907-2-git-send-email-pmorel@linux.ibm.com>
Acked-by: Collin Walling <walling@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Comit 2c28c49057 ("s390x/pci: let pci devices start in configured mode")
changed the initial state of zPCI devices from ZPCI_FS_STANDBY to
ZPCI_FS_DISABLED (a.k.a. configured). However we still only send a
HP_EVENT_RESERVED_TO_STANDBY event to the guest, indicating a wrong
state.
Let's send a HP_EVENT_TO_CONFIGURED event instead, to match the actual
state the device is in.
This fixes hotplugged devices having to be enabled explicitly in the
guest e.g. via echo 1 > /sys/bus/pci/slots/00000000/power.
On real HW, a PCI device always pops up in the STANDBY state. In QEMU,
we decided to let it show up directly in the configured state (as
configuring it is otherwise just an extra burden for the admin). We can
safely bypass the STANDBY state when hotplugging PCI devices to a guest.
Fixes: 2c28c49057 ("s390x/pci: let pci devices start in configured mode")
Reported-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20190110210358.24035-1-david@redhat.com>
Tested-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Pierre Morel <pmorel@linux.ibm.com>
Reviewed-by: Collin Walling <walling@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
When getting the 'pbdev', the if...else has no default branch.
From Coverity, the 'pbdev' maybe null when the 'dev' is not
the TYPE_PCI_BRIDGE/TYPE_PCI_DEVICE/TYPE_S390_PCI_DEVICE.
This patch adds a default branch for device plug and unplug.
Spotted by Coverity: CID 1398593
Signed-off-by: Li Qiang <liq3ea@163.com>
Message-Id: <20190108151114.33140-1-liq3ea@163.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Halil Pasic <pasic@linux.ibm.com>
Reviewed-by: Collin Walling <walling@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
GCC 8 added a -Wstringop-truncation warning:
The -Wstringop-truncation warning added in GCC 8.0 via r254630 for
bug 81117 is specifically intended to highlight likely unintended
uses of the strncpy function that truncate the terminating NUL
character from the source string.
This new warning leads to compilation failures:
CC hw/acpi/core.o
In function 'acpi_table_install', inlined from 'acpi_table_add' at qemu/hw/acpi/core.c:296:5:
qemu/hw/acpi/core.c:184:9: error: 'strncpy' specified bound 4 equals destination size [-Werror=stringop-truncation]
strncpy(ext_hdr->sig, hdrs->sig, sizeof ext_hdr->sig);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
make: *** [qemu/rules.mak:69: hw/acpi/core.o] Error 1
Use the QEMU_NONSTRING attribute, since ACPI tables don't require the
strings to be NUL-terminated.
Suggested-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
When using the generated memory hotplug AML, the iasl
compiler would give the following error:
dsdt.dsl 266: Return (MOST (_UID, Arg0, Arg1, Arg2))
Error 6080 - Called method returns no value ^
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Note: the "Platform Reset Attack Mitigation" specification isn't
explicit about NVDIMM, since they could have different usages. It uses
the term "system memory" generally (and also "volatile memory RAM" in
its introduction). For initial support, I propose to consider
non-volatile memory as not being subject to the memory clear. There is
an on-going discussion in the TCG "pcclientwg" working group for
future revisions.
CPU cache clearing is done unconditionally in edk2 since commit
d20ae95a13e851 (edk2-stable201811).
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Stefan Berger <stefanb@linux.ibm.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The interface is described in the "TCG Platform Reset Attack
Mitigation Specification", chapter 6 "ACPI _DSM Function". According
to Laszlo, it's not so easy to implement in OVMF, he suggested to do
it in qemu instead.
See specification documentation for more details, and next commit for
memory clear on reset handling.
The underlying TCG specification is accessible from the following
page.
https://trustedcomputinggroup.org/resource/pc-client-work-group-platform-reset-attack-mitigation-specification-version-1-0/
This patch implements version 1.0.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Tested-by: Stefan Berger <stefanb@linux.ibm.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The TPM Physical Presence interface consists of an ACPI part, a shared
memory part, and code in the firmware. Users can send messages to the
firmware by writing a code into the shared memory through invoking the
ACPI code. When a reboot happens, the firmware looks for the code and
acts on it by sending sequences of commands to the TPM.
This patch adds the ACPI code. It is similar to the one in EDK2 but doesn't
assume that SMIs are necessary to use. It uses a similar datastructure for
the shared memory as EDK2 does so that EDK2 and SeaBIOS could both make use
of it. I extended the shared memory data structure with an array of 256
bytes, one for each code that could be implemented. The array contains
flags describing the individual codes. This decouples the ACPI implementation
from the firmware implementation.
The underlying TCG specification is accessible from the following page.
https://trustedcomputinggroup.org/tcg-physical-presence-interface-specification/
This patch implements version 1.30.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
[ Marc-André - ACPI code improvements and windows fixes ]
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Stefan Berger <stefanb@linux.ibm.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
To avoid having to hard code the base address of the PPI virtual
memory device we introduce a fw_cfg file etc/tpm/config that holds the
base address of the PPI device, the version of the PPI interface and
the version of the attached TPM.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
[ Marc-André: renamed to etc/tpm/config, made it static, document it ]
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Stefan Berger <stefanb@linux.ibm.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Implement a virtual memory device for the TPM Physical Presence interface.
The memory is located at 0xFED45000 and used by ACPI to send messages to the
firmware (BIOS) and by the firmware to provide parameters for each one of
the supported codes.
This interface should be used by all TPM devices on x86 and can be
added by calling tpm_ppi_init_io().
Note: bios_linker cannot be used to allocate the PPI memory region,
since the reserved memory should stay stable across reboots, and might
be needed before the ACPI tables are installed.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Stefan Berger <stefanb@linux.ibm.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The following patches implement the TPM Physical Presence Interface,
make use of a new memory region and a fw_cfg entry. Enable PPI by
default with >=4.0 machine type, to avoid migration issues.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Stefan Berger <stefanb@linux.ibm.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Let's supplement the msi_uninit() when failing to realize
the pci edu device.
Reported-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Fei Li <shirley17fei@gmail.com>
Reviewed-by: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The disable-legacy and disable-modern properties apply only to
some virtio-pci devices. Make those properties optional.
This fixes the crash introduced by commit f6e501a28e ("virtio: Provide
version-specific variants of virtio PCI devices"):
$ qemu-system-x86_64 -machine pc-i440fx-2.6 \
-device virtio-net-pci-non-transitional
Unexpected error in object_property_find() at qom/object.c:1092:
qemu-system-x86_64: -device virtio-net-pci-non-transitional: can't apply \
global virtio-pci.disable-modern=on: Property '.disable-modern' not found
Aborted (core dumped)
Reported-by: Thomas Huth <thuth@redhat.com>
Fixes: f6e501a28e ("virtio: Provide version-specific variants of virtio PCI devices")
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Virtio console and qga tests also depend on CONFIG_VIRTIO_SERIAL.
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Notice that we can't still run tests with it disabled. Both cdrom-test and
drive_del-test use virtio-scsi without checking if it is enabled.
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Acked-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
For consistency with other devices, rename
virtio_host_{initfn,pci_info} to virtio_input_host_{initfn,info}.
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Allocated feature bit changed in spec draft per TC request.
Signed-off-by: Yuri Benditovich <yuri.benditovich@daynix.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This commit adds implementation of RX packets
coalescing, compatible with requirements of Windows
Hardware compatibility kit.
The device enables feature VIRTIO_NET_F_RSC_EXT in
host features if it supports extended RSC functionality
as defined in the specification.
This feature requires at least one of VIRTIO_NET_F_GUEST_TSO4,
VIRTIO_NET_F_GUEST_TSO6. Windows guest driver acks
this feature only if VIRTIO_NET_F_CTRL_GUEST_OFFLOADS
is also present.
If the guest driver acks VIRTIO_NET_F_RSC_EXT feature,
the device coalesces TCPv4 and TCPv6 packets (if
respective VIRTIO_NET_F_GUEST_TSO feature is on,
populates extended RSC information in virtio header
and sets VIRTIO_NET_HDR_F_RSC_INFO bit in header flags.
The device does not recalculate checksums in the coalesced
packet, so they are not valid.
In this case:
All the data packets in a tcp connection are cached
to a single buffer in every receive interval, and will
be sent out via a timer, the 'virtio_net_rsc_timeout'
controls the interval, this value may impact the
performance and response time of tcp connection,
50000(50us) is an experience value to gain a performance
improvement, since the whql test sends packets every 100us,
so '300000(300us)' passes the test case, it is the default
value as well, tune it via the command line parameter
'rsc_interval' within 'virtio-net-pci' device, for example,
to launch a guest with interval set as '500000':
'virtio-net-pci,netdev=hostnet1,bus=pci.0,id=net1,mac=00,
guest_rsc_ext=on,rsc_interval=500000'
The timer will only be triggered if the packets pool is not empty,
and it'll drain off all the cached packets.
'NetRscChain' is used to save the segments of IPv4/6 in a
VirtIONet device.
A new segment becomes a 'Candidate' as well as it passed sanity check,
the main handler of TCP includes TCP window update, duplicated
ACK check and the real data coalescing.
An 'Candidate' segment means:
1. Segment is within current window and the sequence is the expected one.
2. 'ACK' of the segment is in the valid window.
Sanity check includes:
1. Incorrect version in IP header
2. An IP options or IP fragment
3. Not a TCP packet
4. Sanity size check to prevent buffer overflow attack.
5. An ECN packet
Even though, there might more cases should be considered such as
ip identification other flags, while it breaks the test because
windows set it to the same even it's not a fragment.
Normally it includes 2 typical ways to handle a TCP control flag,
'bypass' and 'finalize', 'bypass' means should be sent out directly,
while 'finalize' means the packets should also be bypassed, but this
should be done after search for the same connection packets in the
pool and drain all of them out, this is to avoid out of order fragment.
All the 'SYN' packets will be bypassed since this always begin a new'
connection, other flags such 'URG/FIN/RST/CWR/ECE' will trigger a
finalization, because this normally happens upon a connection is going
to be closed, an 'URG' packet also finalize current coalescing unit.
Statistics can be used to monitor the basic coalescing status, the
'out of order' and 'out of window' means how many retransmitting packets,
thus describe the performance intuitively.
Difference between ip v4 and v6 processing:
Fragment length in ipv4 header includes itself, while it's not
included for ipv6, thus means ipv6 can carry a real 65535 payload.
Note that main goal of implementing this feature in software
is to create reference setup for certification tests. In such
setups guest migration is not required, so the coalesced packets
not yet delivered to the guest will be lost in case of migration.
Signed-off-by: Wei Xu <wexu@redhat.com>
Signed-off-by: Yuri Benditovich <yuri.benditovich@daynix.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Currently, the vhost-user-test assumes the eventfd is available.
However it's not true because the accel is qtest. So the
'vhost_set_vring_file' will not add fds to the msg and the server
side of vhost-user-test will be broken. The bug is in 'ioeventfd_enabled'.
We should make this function return true if not using kvm accel.
Signed-off-by: Li Qiang <liq3ea@163.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Memset vhost_dev to zero in the vhost_dev_cleanup function.
This causes dev.vqs to be NULL, so that
vqs does not free up space when calling the g_free function.
This will result in a memory leak. But you can't release vqs
directly in the vhost_dev_cleanup function, because vhost_net
will also call this function, and vhost_net's vqs is assigned by array.
In order to solve this problem, we first save the pointer of vqs,
and release the space of vqs after vhost_dev_cleanup is called.
Signed-off-by: Jian Wang <wangjian161@huawei.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
It's been marked as deprecated in QEMU v2.6.0 already, so really nobody
should use the legacy "ivshmem" device anymore (but use ivshmem-plain or
ivshmem-doorbell instead). Time to remove the deprecated device now.
Belatedly also update a mention of the deprecated "ivshmem" in the file
docs/specs/ivshmem-spec.txt to "ivshmem-doorbell". Missed in commit
5400c02b90 ("ivshmem: Split ivshmem-plain, ivshmem-doorbell off ivshmem").
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
In msix_exclusive_bar the bar_pba_size is more than what the pba is
expected to have, although this never affects the bar size.
Specifically, the math in msix_init_exclusive_bar allocates too much
memory in some cases.
For example consider nentries = 8. msix_exclusive_bar will give us
bar_pba_size = 16. So 16 bytes. However 8 bytes would be enough - this
is all that the spec requires.
So in practice bar_pba_size sometimes allocates an extra 8 bytes but
never more.
Since each MSIX entry size is 16 bytes, and since we make sure that
table+pba is a power of two, this always leaves a multiple of 16 bytes
for the PBA, so extra 8 bytes have no effect.
However, its ugly to have pba size temporary variable have an incorrect
value. For consistency switch to the formula used in msix_init.
Signed-off-by: Dongli Zhang <dongli.zhang@oracle.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
We better stop right away. For now, errors would be partially ignored
(so the guest might get informed or the device might get unplugged),
although actual plug/unplug will be reported as failed to the user.
While at it, properly move the check to the pre_plug handler for the plug
case, as we can test the slot state before the device will be realized.
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
* Reenable RDTSCP support on Opteron_G[345] CPU models CPU models
(Borislav Petkov)
* host-phys-bits-limit option for better control of 5-level EPT
(Eduardo Habkost)
* Disable MPX support on named CPU models (Paolo Bonzini)
* expose HV_CPUID_ENLIGHTMENT_INFO.EAX and HV_CPUID_NESTED_FEATURES.EAX
as feature words (Vitaly Kuznetsov)
-----BEGIN PGP SIGNATURE-----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=S08V
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/ehabkost/tags/x86-next-pull-request' into staging
x86 queue, 2019-01-14
* Reenable RDTSCP support on Opteron_G[345] CPU models CPU models
(Borislav Petkov)
* host-phys-bits-limit option for better control of 5-level EPT
(Eduardo Habkost)
* Disable MPX support on named CPU models (Paolo Bonzini)
* expose HV_CPUID_ENLIGHTMENT_INFO.EAX and HV_CPUID_NESTED_FEATURES.EAX
as feature words (Vitaly Kuznetsov)
# gpg: Signature made Mon 14 Jan 2019 14:33:55 GMT
# gpg: using RSA key 2807936F984DC5A6
# gpg: Good signature from "Eduardo Habkost <ehabkost@redhat.com>"
# Primary key fingerprint: 5A32 2FD5 ABC4 D3DB ACCF D1AA 2807 936F 984D C5A6
* remotes/ehabkost/tags/x86-next-pull-request:
i386/kvm: add a comment explaining why .feat_names are commented out for Hyper-V feature bits
x86: host-phys-bits-limit option
target/i386: Disable MPX support on named CPU models
target-i386: Reenable RDTSCP support on Opteron_G[345] CPU models CPU models
i386/kvm: expose HV_CPUID_ENLIGHTMENT_INFO.EAX and HV_CPUID_NESTED_FEATURES.EAX as feature words
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
MPX support is being phased out by Intel; GCC has dropped it, Linux
is also going to do that. Even though KVM will have special code
to support MPX after the kernel proper stops enabling it in XCR0,
we probably also want to deprecate that in a few years. As a start,
do not enable it by default for any named CPU model starting with
the 4.0 machine types; this include Skylake, Icelake and Cascadelake.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20181220121100.21554-1-pbonzini@redhat.com>
Reviewed-by: Wainer dos Santos Moschetta <wainersm@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
The missing functionality was added ~3 years ago with the Linux commit
46896c73c1a4 ("KVM: svm: add support for RDTSCP")
so reenable RDTSCP support on those CPU models.
Opteron_G2 - being family 15, model 6, doesn't have RDTSCP support
(the real hardware doesn't have it. K8 got RDTSCP support with the NPT
models, i.e., models >= 0x40).
Document the host's minimum required kernel version, while at it.
Signed-off-by: Borislav Petkov <bp@suse.de>
Message-ID: <20181212200803.GG6653@zn.tnic>
[ehabkost: moved compat properties code to pc.c]
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
The xen-block dataplane currently allocates memory to hold the data for
each request as that request is used, and frees it afterwards. Because
it requires page-aligned blocks, this interacts poorly with non-page-
aligned allocations and balloons the heap.
Instead, allocate the maximum possible buffer size required for the
protocol, which is BLKIF_MAX_SEGMENTS_PER_REQUEST (currently 11) pages
when the request structure is created, and keep that buffer until it is
destroyed. Since the requests are re-used via a free list, this should
actually improve memory usage.
Signed-off-by: Tim Smith <tim.smith@citrix.com>
Re-based and commit comment adjusted.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Acked-by: Anthony PERARD <anthony.perard@citrix.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
If the I/O ring is full, the guest cannot send any more requests
until some responses are sent. Only sending all available responses
just before checking for new work does not leave much time for the
guest to supply new work, so this will cause stalls if the ring gets
full. Also, not completing reads as soon as possible adds latency
to the guest.
To alleviate that, complete IO requests as soon as they come back.
xen_block_send_response() already returns a value indicating whether
a notify should be sent, which is all the batching we need.
Signed-off-by: Tim Smith <tim.smith@citrix.com>
Re-based and commit comment adjusted.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Acked-by: Anthony PERARD <anthony.perard@citrix.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
When I/O consists of many small requests, performance is improved by
batching them together in a single io_submit() call. When there are
relatively few requests, the extra overhead is not worth it. This
introduces a check to start batching I/O requests via blk_io_plug()/
blk_io_unplug() in an amount proportional to the number which were
already in flight at the time we started reading the ring.
Signed-off-by: Tim Smith <tim.smith@citrix.com>
Re-based and commit comment adjusted.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Acked-by: Anthony PERARD <anthony.perard@citrix.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
xend have been replaced by libxenlight (libxl) for many Xen releases
now.
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
Acked-by: Stefano Stabellini <sstabellini@kernel.org>
It is broken since Xen 4.9 [1] and it will not build in Xen 4.12. Also,
it is not built by default since QEMU 2.6.
[1] https://lists.xenproject.org/archives/html/xen-devel/2018-09/msg00313.html
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
Acked-by: Stefano Stabellini <sstabellini@kernel.org>
This backend has now been replaced by the 'xen-qdisk' XenDevice.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Acked-by: Anthony Perard <anthony.perard@citrix.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
This patch adds create and destroy function for XenBlockDevice-s so that
they can be created automatically when the Xen toolstack instantiates a new
PV backend via xenstore. When the XenBlockDevice is created this way it is
also necessary to create a 'drive' which matches the configuration that the
Xen toolstack has written into xenstore. This is done by formulating the
parameters necessary for each 'blockdev' layer of the drive and then using
qmp_blockdev_add() to create the layers. Also, for compatibility with the
legacy 'xen_disk' implementation, an iothread is automatically created for
the new XenBlockDevice. This, like the driver layers, will be destroyed
after the XenBlockDevice is unrealized.
The legacy backend scan for 'qdisk' is removed by this patch, which makes
the 'xen_disk' code is redundant. The code will be removed by a subsequent
patch.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Reviewed-by: Anthony PERARD <anthony.perard@citrix.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
...that maintains compatibility with existing Xen toolstacks.
Xen toolstacks instantiate PV backends by simply writing information into
xenstore and expecting a backend implementation to be watching for this.
This patch adds a new 'xen-backend' module to allow individual XenDevice
implementations to register create and destroy functions. The creator
will be called when a tool-stack instantiates a new backend in this way,
and the destructor will then be called after the resulting XenDevice
object is unrealized.
To support this it is also necessary to add new watchers into the XenBus
implementation to handle enumeration of new backends and also destruction
of XenDevice-s when the toolstack sets the backend 'online' key to 0.
NOTE: This patch only adds the framework. A subsequent patch will add a
creator function for xen-block devices.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Reviewed-by: Anthony Perard <anthony.perard@citrix.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
...and wire in the dataplane.
This patch adds the remaining code to make the xen-block XenDevice
functional. The parameters that a block frontend expects to find are
populated in the backend xenstore area, and the 'ring-ref' and
'event-channel' values specified in the frontend xenstore area are
mapped/bound and used to set up the dataplane.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Reviewed-by: Anthony Perard <anthony.perard@citrix.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
This is a purely cosmetic patch that purges remaining use of 'blk' and
'ioreq' in local function names, and then makes sure all functions are
prefixed with 'xen_block_'.
No functional change.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Acked-by: Anthony Perard <anthony.perard@citrix.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
This is a purely cosmetic patch that purges the name 'ioreq' from struct,
variable and field names. (This name has been problematic for a long time
as 'ioreq' is the name used for generic I/O requests coming from Xen).
The patch replaces 'struct ioreq' with a new 'XenBlockRequest' type and
'ioreq' field/variable names with 'request', and then does necessary
fix-up to adhere to coding style.
Function names are not modified by this patch. They will be dealt with in
a subsequent patch.
No functional change.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Acked-by: Anthony Perard <anthony.perard@citrix.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
This is a purely cosmetic patch that substitutes the old 'struct XenBlkDev'
name with 'XenBlockDataPlane' and 'blkdev' field/variable names with
'dataplane', and then does necessary fix-up to adhere to coding style.
No functional change.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Acked-by: Anthony Perard <anthony.perard@citrix.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
This patch adds the transformations necessary to get dataplane/xen-block.c
to build against the new XenBus/XenDevice framework. MAINTAINERS is also
updated due to the introduction of dataplane/xen-block.h.
NOTE: Existing data structure names are retained for the moment. These will
be modified by subsequent patches. A typedef for XenBlockDataPlane
has been added to the header (based on the old struct XenBlkDev name
for the moment) so that the old names don't need to leak out of the
dataplane code.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Reviewed-by: Anthony Perard <anthony.perard@citrix.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
Not all of the code duplicated from xen_disk.c is required as the basis for
the new dataplane implementation so this patch removes extraneous code,
along with the legacy #includes and calls to the legacy xen_pv_printf()
function. Error messages are changed to be reported using error_report().
NOTE: The code is still not yet built. Further transformations will be
required to make it correctly interface to the new XenBus/XenDevice
framework. They will be delivered in a subsequent patch.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Acked-by: Anthony Perard <anthony.perard@citrix.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
The new xen-block XenDevice implementation requires the same core
dataplane as the legacy xen_disk implementation it will eventually replace.
This patch therefore copies the legacy xen_disk.c source module into a new
dataplane/xen-block.c source module as the basis for the new dataplane and
adjusts the MAINTAINERS file accordingly.
NOTE: The duplicated code is not yet built. It is simply put into place by
this patch (just fixing style violations) such that the
modifications that will need to be made to the code are not
conflated with code movement, thus making review harder.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Acked-by: Anthony Perard <anthony.perard@citrix.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
The legacy PV backend infrastructure provides functions to bind, unbind
and send notifications to event channnels. Similar functionality will be
required by XenDevice implementations so this patch adds the necessary
support.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Reviewed-by: Anthony Perard <anthony.perard@citrix.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
Patch squashed with:
Patch "xen: add event channel interface for XenDevice-s" makes use of
the type xenevtchn_port_or_error_t, but this isn't avaiable before Xen
4.7. Also the function xen_device_bind_event_channel assign the return
value of xenevtchn_bind_interdomain to channel->local_port but check the
result for error with xendev->local_port.
Fix by:
- removing local_port from struct XenDevice as it isn't use anywere.
- adding a compatibility typedef for xenevtchn_port_or_error_t for Xen
4.6 and earlier.
As extra, replace the type of XenEventChannel->local_port by
evtchn_port_t.
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
Reviewed-by: Paul Durrant <paul.durrant@citrix.com>
The legacy PV backend infrastructure provides functions to map, unmap and
copy pages granted by frontends. Similar functionality will be required
by XenDevice implementations so this patch adds the necessary support.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Reviewed-by: Anthony Perard <anthony.perard@citrix.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
A Xen PV frontend communicates its state to the PV backend by writing to
the 'state' key in the frontend area in xenstore. It is therefore
necessary for a XenDevice implementation to be notified whenever the
value of this key changes.
This patch adds code to do this as follows:
- an 'fd handler' is registered on the libxenstore handle which will be
triggered whenever a 'watch' event occurs
- primitives are added to xen-bus-helper to add or remove watch events
- a list of Notifier objects is added to XenBus to provide a mechanism
to call the appropriate 'watch handler' when its associated event
occurs
The xen-block implementation is extended with a 'frontend_changed' method,
which calls as-yet stub 'connect' and 'disconnect' functions when the
relevant frontend state transitions occur. A subsequent patch will supply
a full implementation for these functions.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Reviewed-by: Anthony Perard <anthony.perard@citrix.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
This patch adds a new source module, xen-bus-helper.c, which builds on
basic libxenstore primitives to provide functions to create (setting
permissions appropriately) and destroy xenstore areas, and functions to
'printf' and 'scanf' nodes therein. The main xen-bus code then uses
these primitives [1] to initialize and destroy the frontend and backend
areas for a XenDevice during realize and unrealize respectively.
The 'xen-block' implementation is extended with a 'get_name' method that
returns the VBD number. This number is required to 'name' the xenstore
areas.
NOTE: An exit handler is also added to make sure the xenstore areas are
cleaned up if QEMU terminates without devices being unrealized.
[1] The 'scanf' functions are actually not yet needed, but they will be
needed by code delivered in subsequent patches.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Reviewed-by: Anthony Perard <anthony.perard@citrix.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
This patch adds new XenDevice-s: 'xen-disk' and 'xen-cdrom', both derived
from a common 'xen-block' parent type. These will eventually replace the
'xen_disk' (note the underscore rather than hyphen) legacy PV backend but
it is illustrative to build up the implementation incrementally, along with
the XenBus/XenDevice framework. Subsequent patches will therefore add to
these devices' implementation as new features are added to the framework.
After this patch has been applied it is possible to instantiate new
'xen-disk' or 'xen-cdrom' devices with a single 'vdev' parameter, which
accepts values adhering to the Xen VBD naming scheme [1]. For example, a
command-line instantiation of a xen-disk can be done with an argument
similar to the following:
-device xen-disk,vdev=hda
The implementation of the vdev parameter formulates the appropriate VBD
number for use in the PV protocol.
[1] https://xenbits.xen.org/docs/unstable/man/xen-vbd-interface.7.html
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Reviewed-by: Anthony Perard <anthony.perard@citrix.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
This patch adds the basic boilerplate for a 'XenBus' object that will act
as a parent to 'XenDevice' PV backends.
A new 'XenBridge' object is also added to connect XenBus to the system bus.
The XenBus object is instantiated by a new xen_bus_init() function called
from the same sites as the legacy xen_be_init() function.
Subsequent patches will flesh-out the functionality of these objects.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Reviewed-by: Anthony Perard <anthony.perard@citrix.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
...and xen_backend.h to xen-legacy-backend.h
Rather than attempting to convert the existing backend infrastructure to
be QOM compliant (which would be hard to do in an incremental fashion),
subsequent patches will introduce a completely new framework for Xen PV
backends. Hence it is necessary to re-name parts of existing code to avoid
name clashes. The re-named 'legacy' infrastructure will be removed once all
backends have been ported to the new framework.
This patch is purely cosmetic. No functional change.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Acked-by: Anthony Perard <anthony.perard@citrix.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
For some pci device, even its PCI_INTERRUPT_PIN is not 0, it actually
doesn't support INTx mode, so its machine irq read from host sysfs is 0.
In that case, report PCI_INTERRUPT_PIN as 0 to guest and let passthrough
continue.
Reviewed-by: Roger Pau Monné <roger.pau@citrix.com>
Signed-off-by: Zhao Yan <yan.y.zhao@intel.com>
Acked-by: Anthony PERARD <anthony.perard@citrix.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
Coverity (CID 796599) points out that xen_pt_setup_vga() trusts
the rom->size field in the BIOS ROM from a PCI passthrough VGA
device, and uses it as an index into the memory which contains
the BIOS image. A corrupt BIOS ROM could therefore cause us to
index off the end of the buffer.
Check that the size is within bounds before we use it.
We are also trusting the pcioffset field, and assuming that
the whole rom_header is present; Coverity doesn't notice these,
but check them too.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Anthony PERARD <anthony.perard@citrix.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
* esp bugfixes (Guenter)
* Windows build cleanup (Marc-André)
* checkpatch logic improvements (Paolo)
* coalesced range bugfix (Paolo)
* switch testsuite to TAP (Paolo)
* QTAILQ rewrite (Paolo)
* block/iscsi.c cancellation fixes (Stefan)
* improve selection of the default accelerator (Thomas)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJcOKyMAAoJEL/70l94x66DxKEH/1ho2Xl8ezxCecA6q3HqTgMT
NJ/ntdqQwVwekKOWzsywnM3/LkEDLH55MxbTeQ8M/Vb1seS8eROz24/gPTzvFrfR
n/d11rDV1EJfWe0H7nGLLFiRv0MSjxLpG9c3dlOKWhwOYHm25tr48PsdfVFP9Slz
BK3rwrMeDgArfptHAIsAXt2h1S0EzrG9pMwGDpErCDzziXxBhUESE0Iqfw8LsH1K
VjMn6rn7Ts1XKlxxwsm+BzHlTJghbj3tWPIfk+6uK2isP4iM3gFCoav3SG9XVXof
V9+vFyMxdtZKT/0HvajhUS4/1S/uGBNNchZRnCxXlpbueWc5ROtvarhM6Hb0eck=
=i8E5
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/bonzini/tags/for-upstream' into staging
* HAX support for Linux hosts (Alejandro)
* esp bugfixes (Guenter)
* Windows build cleanup (Marc-André)
* checkpatch logic improvements (Paolo)
* coalesced range bugfix (Paolo)
* switch testsuite to TAP (Paolo)
* QTAILQ rewrite (Paolo)
* block/iscsi.c cancellation fixes (Stefan)
* improve selection of the default accelerator (Thomas)
# gpg: Signature made Fri 11 Jan 2019 14:47:40 GMT
# gpg: using RSA key BFFBD25F78C7AE83
# gpg: Good signature from "Paolo Bonzini <bonzini@gnu.org>"
# gpg: aka "Paolo Bonzini <pbonzini@redhat.com>"
# Primary key fingerprint: 46F5 9FBD 57D6 12E7 BFD4 E2F7 7E15 100C CD36 69B1
# Subkey fingerprint: F133 3857 4B66 2389 866C 7682 BFFB D25F 78C7 AE83
* remotes/bonzini/tags/for-upstream: (34 commits)
avoid TABs in files that only contain a few
remove space-tab sequences
scripts: add script to convert multiline comments into 4-line format
hw/watchdog/wdt_i6300esb: remove a unnecessary comment
checkpatch: warn about qemu/queue.h head structs that are not typedef-ed
qemu/queue.h: simplify reverse access to QTAILQ
qemu/queue.h: reimplement QTAILQ without pointer-to-pointers
qemu/queue.h: remove Q_TAILQ_{HEAD,ENTRY}
qemu/queue.h: typedef QTAILQ heads
qemu/queue.h: leave head structs anonymous unless necessary
vfio: make vfio_address_spaces static
qemu/queue.h: do not access tqe_prev directly
test: replace gtester with a TAP driver
test: execute g_test_run when tests are skipped
qga: drop < Vista compatibility
build-sys: build with Vista API by default
build-sys: move windows defines in osdep.h header
build-sys: don't include windows.h, osdep.h does it
scsi: esp: Defer command completion until previous interrupts have been handled
esp-pci: Fix status register write erase control
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Most files that have TABs only contain a handful of them. Change
them to spaces so that we don't confuse people.
disas, standard-headers, linux-headers and libdecnumber are imported
from other projects and probably should be exempted from the check.
Outside those, after this patch the following files still contain both
8-space and TAB sequences at the beginning of the line. Many of them
have a majority of TABs, or were initially committed with all tabs.
bsd-user/i386/target_syscall.h
bsd-user/x86_64/target_syscall.h
crypto/aes.c
hw/audio/fmopl.c
hw/audio/fmopl.h
hw/block/tc58128.c
hw/display/cirrus_vga.c
hw/display/xenfb.c
hw/dma/etraxfs_dma.c
hw/intc/sh_intc.c
hw/misc/mst_fpga.c
hw/net/pcnet.c
hw/sh4/sh7750.c
hw/timer/m48t59.c
hw/timer/sh_timer.c
include/crypto/aes.h
include/disas/bfd.h
include/hw/sh4/sh.h
libdecnumber/decNumber.c
linux-headers/asm-generic/unistd.h
linux-headers/linux/kvm.h
linux-user/alpha/target_syscall.h
linux-user/arm/nwfpe/double_cpdo.c
linux-user/arm/nwfpe/fpa11_cpdt.c
linux-user/arm/nwfpe/fpa11_cprt.c
linux-user/arm/nwfpe/fpa11.h
linux-user/flat.h
linux-user/flatload.c
linux-user/i386/target_syscall.h
linux-user/ppc/target_syscall.h
linux-user/sparc/target_syscall.h
linux-user/syscall.c
linux-user/syscall_defs.h
linux-user/x86_64/target_syscall.h
slirp/cksum.c
slirp/if.c
slirp/ip.h
slirp/ip_icmp.c
slirp/ip_icmp.h
slirp/ip_input.c
slirp/ip_output.c
slirp/mbuf.c
slirp/misc.c
slirp/sbuf.c
slirp/socket.c
slirp/socket.h
slirp/tcp_input.c
slirp/tcpip.h
slirp/tcp_output.c
slirp/tcp_subr.c
slirp/tcp_timer.c
slirp/tftp.c
slirp/udp.c
slirp/udp.h
target/cris/cpu.h
target/cris/mmu.c
target/cris/op_helper.c
target/sh4/helper.c
target/sh4/op_helper.c
target/sh4/translate.c
tcg/sparc/tcg-target.inc.c
tests/tcg/cris/check_addo.c
tests/tcg/cris/check_moveq.c
tests/tcg/cris/check_swap.c
tests/tcg/multiarch/test-mmap.c
ui/vnc-enc-hextile-template.h
ui/vnc-enc-zywrle.h
util/envlist.c
util/readline.c
The following have only TABs:
bsd-user/i386/target_signal.h
bsd-user/sparc64/target_signal.h
bsd-user/sparc64/target_syscall.h
bsd-user/sparc/target_signal.h
bsd-user/sparc/target_syscall.h
bsd-user/x86_64/target_signal.h
crypto/desrfb.c
hw/audio/intel-hda-defs.h
hw/core/uboot_image.h
hw/sh4/sh7750_regnames.c
hw/sh4/sh7750_regs.h
include/hw/cris/etraxfs_dma.h
linux-user/alpha/termbits.h
linux-user/arm/nwfpe/fpopcode.h
linux-user/arm/nwfpe/fpsr.h
linux-user/arm/syscall_nr.h
linux-user/arm/target_signal.h
linux-user/cris/target_signal.h
linux-user/i386/target_signal.h
linux-user/linux_loop.h
linux-user/m68k/target_signal.h
linux-user/microblaze/target_signal.h
linux-user/mips64/target_signal.h
linux-user/mips/target_signal.h
linux-user/mips/target_syscall.h
linux-user/mips/termbits.h
linux-user/ppc/target_signal.h
linux-user/sh4/target_signal.h
linux-user/sh4/termbits.h
linux-user/sparc64/target_syscall.h
linux-user/sparc/target_signal.h
linux-user/x86_64/target_signal.h
linux-user/x86_64/termbits.h
pc-bios/optionrom/optionrom.h
slirp/mbuf.h
slirp/misc.h
slirp/sbuf.h
slirp/tcp.h
slirp/tcp_timer.h
slirp/tcp_var.h
target/i386/svm.h
target/sparc/asi.h
target/xtensa/core-dc232b/xtensa-modules.inc.c
target/xtensa/core-dc233c/xtensa-modules.inc.c
target/xtensa/core-de212/core-isa.h
target/xtensa/core-de212/xtensa-modules.inc.c
target/xtensa/core-fsf/xtensa-modules.inc.c
target/xtensa/core-sample_controller/core-isa.h
target/xtensa/core-sample_controller/xtensa-modules.inc.c
target/xtensa/core-test_kc705_be/core-isa.h
target/xtensa/core-test_kc705_be/xtensa-modules.inc.c
tests/tcg/cris/check_abs.c
tests/tcg/cris/check_addc.c
tests/tcg/cris/check_addcm.c
tests/tcg/cris/check_addoq.c
tests/tcg/cris/check_bound.c
tests/tcg/cris/check_ftag.c
tests/tcg/cris/check_int64.c
tests/tcg/cris/check_lz.c
tests/tcg/cris/check_openpf5.c
tests/tcg/cris/check_sigalrm.c
tests/tcg/cris/crisutils.h
tests/tcg/cris/sys.c
tests/tcg/i386/test-i386-ssse3.c
ui/vgafont.h
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20181213223737.11793-3-pbonzini@redhat.com>
Reviewed-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Wainer dos Santos Moschetta <wainersm@redhat.com>
Acked-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: Eric Blake <eblake@redhat.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Stefan Markovic <smarkovic@wavecomp.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
There are not many, and they are all simple mistakes that ended up
being committed. Remove them.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20181213223737.11793-2-pbonzini@redhat.com>
Reviewed-by: Wainer dos Santos Moschetta <wainersm@redhat.com>
Acked-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The registered memory region of i6300esb is not suitable for coalesced
mmio, because a write for the region may trigger an immediate action
and can't be delayed.
Signed-off-by: Peng Hao <peng.hao2@zte.com.cn>
Message-Id: <1544253511-82742-1-git-send-email-peng.hao2@zte.com.cn>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This will be needed when we change the QTAILQ head and elem structs
to unions. However, it is also consistent with the usage elsewhere
in QEMU for other list head structs (see for example FsMountList).
Note that most QTAILQs only need their name in order to do backwards
walks. Those do not break with the struct->union change, and anyway
the change will also remove the need to name heads when doing backwards
walks, so those are not touched here.
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Most list head structs need not be given a name. In most cases the
name is given just in case one is going to use QTAILQ_LAST, QTAILQ_PREV
or reverse iteration, but this does not apply to lists of other kinds,
and even for QTAILQ in practice this is only rarely needed. In addition,
we will soon reimplement those macros completely so that they do not
need a name for the head struct. So clean up everything, not giving a
name except in the rare case where it is necessary.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
It is not used outside hw/vfio/common.c, so it does not need to
be extern.
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The guest OS reads RSTAT, RSEQ, and RINTR, and expects those registers
to reflect a consistent state. However, it is possible that the registers
can change after RSTAT was read, but before RINTR is read, when
esp_command_complete() is called.
Guest OS qemu
-------- ----
[handle interrupt]
Read RSTAT
esp_command_complete()
RSTAT = STAT_ST
esp_dma_done()
RSTAT |= STAT_TC
RSEQ = 0
RINTR = INTR_BS
Read RSEQ
Read RINTR RINTR = 0
RSTAT &= ~STAT_TC
RSEQ = SEQ_CD
The guest OS would then try to handle INTR_BS combined with an old
value of RSTAT. This sometimes resulted in lost events, spurious
interrupts, guest OS confusion, and stalled SCSI operations.
A typical guest error log (observed with various versions of Linux)
looks as follows.
scsi host1: Spurious irq, sreg=13.
...
scsi host1: Aborting command [84531f10:2a]
scsi host1: Current command [f882eea8:35]
scsi host1: Queued command [84531f10:2a]
scsi host1: Active command [f882eea8:35]
scsi host1: Dumping command log
scsi host1: ent[15] CMD val[44] sreg[90] seqreg[00] sreg2[00] ireg[20] ss[00] event[0c]
scsi host1: ent[16] CMD val[01] sreg[90] seqreg[00] sreg2[00] ireg[20] ss[02] event[0c]
scsi host1: ent[17] CMD val[43] sreg[90] seqreg[00] sreg2[00] ireg[20] ss[02] event[0c]
scsi host1: ent[18] EVENT val[0d] sreg[92] seqreg[04] sreg2[00] ireg[18] ss[00] event[0c]
...
Defer handling command completion until previous interrupts have been
handled to fix the problem.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Per AM53C974 datasheet, definition of "SCSI Bus and Control (SBAC)"
register:
Bit 24 'STATUS' Write Erase Control
This bit controls the Write Erase feature on bits 3:1 and bit 6 of the DMA
Status Register ((B)+54h). When this bit is programmed to '1', the state
of bits 3:1 are preserved when read. Bits 3:1 are only cleared when a '1'
is written to the corresponding bit location. For example, to clear bit 1,
the value of '0000_0010b' should be written to the register. When the DMA
Status Preserve bit is '0', bits 3:1 are cleared when read.
The status register is currently defined to bit 12, not bit 24.
Also, its implementation is reversed: The status is auto-cleared if
the bit is set to 1, and must be cleared explicitly when the bit is
set to 0. This results in spurious interrupts reported by the Linux
kernel, and in some cases even results in stalled SCSI operations.
Set SBAC_STATUS to bit 24 and reverse the logic to fix the problem.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Message-Id: <1543442171-24863-1-git-send-email-linux@roeck-us.net>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
usb packets with no payload (zero length) seem to happen in practice for
whatever reason. Add a check and skip the packet then, otherwise we'll
trigger an assert.
Reported-by: Leonardo Soares Müller <leozinho29_eu@hotmail.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20181211072649.20700-1-kraxel@redhat.com
This device does not use I2C, so no need to include the header file here.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1546614146-10525-1-git-send-email-thuth@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Looking at chardev/spice.c code, I realize compilation was broken for
a while with spice-server < 0.12.3. Let's bump required version
to 0.12.5, released May 19 2014, instead of adding more #ifdef.
(this patch combines changes from an early version and some of
Frediano "[PATCH 2/2] spice: Bump required spice-server version to
0.12.6")
According to repology, all the distros that are build target platforms
for QEMU include it:
RHEL-7: 0.14.0
Debian (Stretch): 0.12.8
Debian (Jessie): 0.12.5
FreeBSD (ports): 0.14.0
OpenSUSE Leap 15: 0.14.0
Ubuntu (Xenial): 0.12.6
Note that a previous version of this patch was bumping version to
0.12.6. Unfortunately, Debian Jessie (oldstable) is stuck with spice
server 0.12.5, and QEMU should keep building until after 2y of current
stable (Stretch), which will be around June 17th 2019. Qemu 4.1
should thus be free of bumping to spice-server 0.12.6 during 4.1
development cycle.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Message-id: 20181128155932.16171-1-marcandre.lureau@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Since commit ea9ce8934, device_post_init() applies globals directly
from machines and accelerator classes.
There are cases, such as -device scsi-hd,help, where the machine is
setup but there in no accelerator.
Let's skip accelerator globals in this case.
Fixes SEGV:
#0 0x0000555558ea04ff in object_get_class (obj=0x0) at /home/elmarco/src/qemu/build/../qom/object.c:857
#1 0x000055555854c797 in object_apply_compat_props (obj=0x616000078980) at /home/elmarco/src/qemu/build/../hw/core/qdev.c:978
#2 0x000055555854c797 in object_apply_compat_props (obj=0x616000078980) at /home/elmarco/src/qemu/build/../hw/core/qdev.c:973
#3 0x000055555854c959 in device_post_init (obj=0x616000078980) at /home/elmarco/src/qemu/build/../hw/core/qdev.c:989
#4 0x0000555558e9e250 in object_post_init_with_type (ti=<optimized out>, obj=0x616000078980) at /home/elmarco/src/qemu/build/../qom/object.c:365
#5 0x0000555558e9e250 in object_initialize_with_type (data=0x616000078980, size=616, type=<optimized out>) at /home/elmarco/src/qemu/build/../qom/object.c:425
#6 0x0000555558e9e571 in object_new_with_type (type=0x613000031900) at /home/elmarco/src/qemu/build/../qom/object.c:588
#7 0x000055555830c048 in qmp_device_list_properties (typename=typename@entry=0x60200000c2d0 "scsi-hd", errp=errp@entry=0x7fffffffc540) at /home/elmarco/src/qemu/qmp.c:519
#8 0x00005555582c4027 in qdev_device_help (opts=<optimized out>) at /home/elmarco/src/qemu/qdev-monitor.c:283
#9 0x0000555559378fa2 in qemu_opts_foreach (list=<optimized out>, func=func@entry=0x5555582cfca0 <device_help_func>, opaque=opaque@entry=0x0, errp=errp@entry=0x0) at /home/elmarco/src/qemu/util/qemu-option.c:1171
https://bugzilla.redhat.com/show_bug.cgi?id=1664364
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20190109102311.7635-1-marcandre.lureau@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Lukáš Doktor <ldoktor@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Instead of verbose arrays with 4 lines for each entry, make each
entry take only one line. This makes long arrays that couldn't
fit in the screen become short and readable.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20190107193020.21744-4-ehabkost@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
stringify() is useful when we need to use macros in compat_props
(like when we set virtio-baloon-pci.class=PCI_CLASS_MEMORY_RAM at
pc_i440fx_1_0_machine_options()), but it is pointless when we are
already providing a number literal.
Replace stringify() with string literals when appropriate.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20190107193020.21744-3-ehabkost@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
The macro is only used in one place, where the purpose of the
value is obvious. Eliminate the macro so we don't need to rely
on stringify().
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20190107193020.21744-2-ehabkost@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Let's rewrite it properly using ranges. This fixes certain overflows that
are right now possible. E.g.
qemu-system-x86_64 -m 4G,slots=20,maxmem=40G -M pc \
-object memory-backend-file,id=mem1,share,mem-path=/dev/zero,size=2G
-device pc-dimm,memdev=mem1,id=dimm1,addr=-0x40000000
Now properly errors out instead of succeeding. (Note that qapi
parsing of huge uint64_t values is broken and fixes are on the way)
"can't add memory device [0xffffffffa0000000:0x80000000], usable range for
memory devices [0x140000000:0xe00000000]"
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20181214131043.25071-3-david@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Make them more QOMConventional.
Cc:qemu-trivial@nongnu.org
Signed-off-by: Li Qiang <liq3ea@163.com>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20190105023831.66910-1-liq3ea@163.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
These files don't seem to do anything related to ISA directly, so
there is no need to include isa.h here.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1546615943-16274-1-git-send-email-thuth@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
This device does not use I2C, so no need to include the header file here.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1546614146-10525-1-git-send-email-thuth@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Depending on the interrupt mode of the machine, enable or disable the
XIVE MMIOs.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The 'dual' sPAPR IRQ backend supports both interrupt mode, XIVE
exploitation mode and the legacy compatibility mode (XICS). both modes
are not supported at the same time.
The machine starts with the legacy mode and a new interrupt mode can
then be negotiated by the CAS process. In this case, the new mode is
activated after a reset to take into account the required changes in
the machine. These impact the device tree layout, the interrupt
presenter object and the exposed MMIO regions in the case of XIVE.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The qemu_irq array is now allocated at the machine level using a sPAPR
IRQ set_irq handler depending on the chosen interrupt mode. The use of
this handler is slightly inefficient today but it will become necessary
when the 'dual' interrupt mode is introduced.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Future changes of the ICSState object will remove the qemu_irq array
from under the interrupt controller model. Prepare ground for the PSI
interrupt sources and introduce a new one directly under the PSI
device model.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
To support the 'dual' interrupt mode, XICS and XIVE, we plan to move
the qemu_irq array of each interrupt controller under the machine and
do the allocation under the sPAPR IRQ init method.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The error value can be squashed by the section handling radix migration.
Simply bail out if an error occurs when the RTC offset is imported.
This fixes the Coverity issue CID 1398591.
Fixes: d39c90f5f3 ("spapr: Fix migration of Radix guests")
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Now that the 'intc' pointer is only used by the XICS interrupt mode,
let's make things clear and use a XICS type and name.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
which will be used by the machine only when the XIVE interrupt mode is
in use.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Today, the interrupt presenter is linked to a CPU using the
cpu_intc_create() method of the sPAPR IRQ backend. The resulting
object is assigned to the PowerPCCPU 'intc' pointer whatever the
interrupt mode, XICS or XIVE.
To support the 'dual' interrupt mode, we will need to distinguish
between the two presenter objects and for that, we plan to introduce a
second interrupt presenter object pointer under the PowerPCCPU. The
modifications below move the assignment of the presenter object under
the cpu_intc_create() method to prepare ground for the future changes.
Both sPAPR and PowerNV machines are impacted.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The qirq routines of the XiveSource and the sPAPRXive model are only
used under the sPAPR IRQ backend. Simplify the overall call stack and
gather all the code under spapr_qirq_xive(). It will ease future
changes.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
PHB hotplug will bring more users for it. Let's define it along with
the PHB defines from which it is derived for simplicity.
While here fix a misleading comment about manual placement, which was
abandoned with 30b3bc5aa9.
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This adds cleanup counterparts to pci_register_root_bus(),
pci_root_bus_new(), and pci_bus_irqs().
These cleanup routines are needed in the case of hotpluggable
PCIHostBridge implementations. Currently we can rely on the
object_unparent()'ing of the PCIHostState recursively unparenting
and cleaning up it's child buses, but we need explicit calls
to also:
1) remove the PCIHostState from pci_host_bridges global list.
otherwise, we risk accessing freed memory when we access
the list later
2) clean up memory allocated in pci_bus_irqs()
Both are handled outside the context of any particular bus or
host bridge's init/realize functions, making it difficult to
avoid the need for explicit cleanup functions without remodeling
how PCIHostBridges are created. So keep it simple and just add
them for now.
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This function is only used when creating the default PHB. Let's rename
it and move it to the core machine code for clarity.
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Debug logs were left enabled in ppc4xx_devs.c whereas in other files
these are normally not enabled. Disable it here as well.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
SLOF receives a device tree and updates it with various properties
before switching to the guest kernel and QEMU is not aware of any changes
made by SLOF. Since there is no real RTAS (QEMU implements it), it makes
sense to pass the SLOF final device tree to QEMU to let it implement
RTAS related tasks better, such as PCI host bus adapter hotplug.
Specifially, now QEMU can find out the actual XICS phandle (for PHB
hotplug) and the RTAS linux,rtas-entry/base properties (for firmware
assisted NMI - FWNMI).
This stores the initial DT blob in the sPAPR machine and replaces it
in the KVMPPC_H_UPDATE_DT (new private hypercall) handler.
This adds an @update_dt_enabled machine property to allow backward
migration.
SLOF already has a hypercall since
https://github.com/aik/SLOF/commit/e6fc84652c9c0073f9183
This makes use of the new fdt_check_full() helper. In order to allow
the configure script to pick the correct DTC version, this adjusts
the DTC presense test.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
H_HOME_NODE_ASSOCIATIVITY H-Call returns the associativity domain
designation associated with the identifier input parameter
This fixes a crash when we try to hotplug a CPU in memory-less and
CPU-less numa node. In this case, the kernel tries to online the
node, but without the information provided by this h-call, the node id,
it cannot and the CPU is started while the node is not onlined.
It also removes the warning message from the kernel:
VPHN is not supported. Disabling polling..
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This function is only needed when Q35 is in use. Moving it to
the same file that uses it lets you disable the entire USB
subsystem in x86_64-softmmu.mak; of course doing that will
cause -usb to break horribly, but one thing at a time.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-id: 1545064358-4601-1-git-send-email-pbonzini@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
This patch introduces a new system bus generic EHCI controller.
For the system bus EHCI controller, we've already had "xlnx",
"exynos4210", "tegra2", "ppc4xx" and "fusbh200", they are specific and
only suitable for their own platforms, platforms such as an Arm server,
may need a generic system bus EHCI controller, this patch creates it,
and the kernel driver ehci_platform.c works well on it.
Signed-off-by: Hongbo Zhang <hongbo.zhang@linaro.org>
Message-id: 1546077657-22637-1-git-send-email-hongbo.zhang@linaro.org
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
In usb_device_post_load, certain values of dev->setup_len or
dev->setup_index can cause -EINVAL to be returned. One example is when
setup_len exceeds 4096, the hard-coded value of sizeof(dev->data_buf).
This can happen through legitimate guest activity and will cause all
subsequent attempts to migrate the guest to fail in vmstate_load_state.
The values of these variables can be set by USB packets originating in
the guest. There are two ways in which they can be set: in
do_token_setup and in do_parameter in hw/usb/core.c.
It is easy to craft a USB packet in a guest that causes do_token_setup
to set setup_len to a value larger than 4096. When this has been done
once, all subsequent attempts to migrate the VM will fail in
usb_device_post_load until the VM is next power-cycled or a
smaller-sized USB packet is sent to the device.
Sample code for achieving this in a VM started with "-device usb-tablet"
running Linux with CONFIG_HIDRAW=y and HID_MAX_BUFFER_SIZE > 4096:
#include <sys/types.h>
#include <sys/stat.h>
#include <fcntl.h>
#include <unistd.h>
int main() {
char buf[4097];
int fd = open("/dev/hidraw0", O_RDWR|O_NONBLOCK);
buf[0] = 0x1;
write(fd, buf, 4097);
return 0;
}
When this code is run in the VM, qemu will output:
usb_generic_handle_packet: ctrl buffer too small (4097 > 4096)
A subsequent attempt to migrate the VM will fail and output the
following on the destination host:
qemu-kvm: error while loading state for instance 0x0 of device '0000:00:06.7/1/usb-ptr'
qemu-kvm: load of migration failed: Invalid argument
The idea behind checking the values of setup_len and setup_index before
they are used is correct, but doing it in usb_device_post_load feels
arbitrary, and will cause unnecessary migration failures. Indeed, none
of the commit messages for c60174e8, 9f8e9895 and 719ffe1f justify why
post_load is the right place to do these checks. They correctly point
out that the important thing to protect is the usb_packet_copy.
Instead, the right place to do the checks is in do_token_setup and
do_parameter. Indeed, there are already some checks here. We can examine
each of the disjuncts currently tested in usb_device_post_load to see
whether any need adding to do_token_setup or do_parameter to improve
safety there:
* dev->setup_index < 0
- This test is not needed because setup_index is explicitly set to
0 in do_token_setup and do_parameter.
* dev->setup_len < 0
- In both do_token_setup and do_parameter, the value of setup_len
is computed by (s->setup_buf[7] << 8) | s->setup_buf[6]. Since
s->setup_buf is a byte array and setup_len is an int32_t, it's
impossible for this arithmetic to set setup_len's top bit, so it can
never be negative.
* dev->setup_index > dev->setup_len
- Since setup_index is 0, this is equivalent to the previous test,
so is redundant.
* dev->setup_len > sizeof(dev->data_buf)
- This condition is already explicitly checked in both
do_token_setup and do_parameter.
Hence there is no need to bolster the existing checks in do_token_setup
or do_parameter, and we can safely remove these checks from
usb_device_post_load without reducing safety but allowing migrations to
proceed regardless of what USB packets have been generated by the guest.
Signed-off-by: Jonathan Davies <jonathan.davies@nutanix.com>
Message-Id: <20190107175117.23769-1-jonathan.davies@nutanix.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The typhoon MemoryRegionOps callbacks directly call
cpu_unassigned_access(), presumably as the old-fashioned way
to provoke a CPU exception. This won't work since commit
6ad4d7eed0 when we switched Alpha over to the
transaction_failed hook API, because now cpu_unassigned_access()
is a no-op for Alpha.
Make the MemoryRegionOps callbacks use the read_with_attrs
and write_with_attrs hooks, so they can signal a failure
that should cause a CPU exception by returning MEMTX_ERROR.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20181210173350.13073-1-peter.maydell@linaro.org>
Tested-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
* Support u-boot 'noload' images for Arm (as used by NetBSD/evbarm GENERIC kernel)
* hw/misc/tz-mpc: Fix value of BLK_MAX register
* target/arm: Emit barriers for A32/T32 load-acquire/store-release insns
* nRF51 SoC: add timer, GPIO, RNG peripherals
* hw/arm/allwinner-a10: Add the 'A' SRAM and the SRAM controller
* cpus.c: Fix race condition in cpu_stop_current()
* hw/arm: versal: Plug memory leaks
* Allow M profile boards to run even if -kernel not specified
* gdbstub: Add multiprocess extension support for use when the
board has multiple CPUs of different types (like the Xilinx Zynq boards)
* target/arm: Don't decode S bit in SVE brk[ab] merging insns
* target/arm: Convert ARM_TBFLAG_* to FIELDs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=x1jv
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/pmaydell/tags/pull-target-arm-20190107' into staging
target-arm queue:
* Support u-boot 'noload' images for Arm (as used by NetBSD/evbarm GENERIC kernel)
* hw/misc/tz-mpc: Fix value of BLK_MAX register
* target/arm: Emit barriers for A32/T32 load-acquire/store-release insns
* nRF51 SoC: add timer, GPIO, RNG peripherals
* hw/arm/allwinner-a10: Add the 'A' SRAM and the SRAM controller
* cpus.c: Fix race condition in cpu_stop_current()
* hw/arm: versal: Plug memory leaks
* Allow M profile boards to run even if -kernel not specified
* gdbstub: Add multiprocess extension support for use when the
board has multiple CPUs of different types (like the Xilinx Zynq boards)
* target/arm: Don't decode S bit in SVE brk[ab] merging insns
* target/arm: Convert ARM_TBFLAG_* to FIELDs
# gpg: Signature made Mon 07 Jan 2019 16:29:52 GMT
# gpg: using RSA key 3C2525ED14360CDE
# gpg: Good signature from "Peter Maydell <peter.maydell@linaro.org>"
# gpg: aka "Peter Maydell <pmaydell@gmail.com>"
# gpg: aka "Peter Maydell <pmaydell@chiark.greenend.org.uk>"
# Primary key fingerprint: E1A5 C593 CD41 9DE2 8E83 15CF 3C25 25ED 1436 0CDE
* remotes/pmaydell/tags/pull-target-arm-20190107: (37 commits)
Support u-boot noload images for arm as used by, NetBSD/evbarm GENERIC kernel.
hw/misc/tz-mpc: Fix value of BLK_MAX register
target/arm: Emit barriers for A32/T32 load-acquire/store-release insns
arm: Add Clock peripheral stub to NRF51 SOC
tests/microbit-test: Add Tests for nRF51 Timer
arm: Instantiate NRF51 Timers
hw/timer/nrf51_timer: Add nRF51 Timer peripheral
tests/microbit-test: Add Tests for nRF51 GPIO
arm: Instantiate NRF51 general purpose I/O
hw/gpio/nrf51_gpio: Add nRF51 GPIO peripheral
arm: Instantiate NRF51 random number generator
hw/misc/nrf51_rng: Add NRF51 random number generator peripheral
arm: Add header to host common definition for nRF51 SOC peripherals
qtest: Add set_irq_in command to set IRQ/GPIO level
hw/arm/allwinner-a10: Add the 'A' SRAM and the SRAM controller
cpus.c: Fix race condition in cpu_stop_current()
MAINTAINERS: Add ARM-related files for hw/[misc|input|timer]/
hw/arm: versal: Plug memory leaks
Revert "armv7m: Guard against no -kernel argument"
arm/xlnx-zynqmp: put APUs and RPUs in separate CPU clusters
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
noload kernels are loaded with the u-boot image header and as a result
the header size needs adding to the entry point. Fake up a hdr so the
kernel image is loaded at the right address and the entry point is
adjusted appropriately.
The default location for the uboot file is 32MiB above bottom of DRAM.
This matches the recommendation in Documentation/arm/Booting.
Clarify the load_uimage API to state the passing of a load address when an
image doesn't specify one, or when loading a ramdisk is expected.
Adjust callers of load_uimage, etc.
Signed-off-by: Nick Hudson <skrll@netbsd.org>
Message-id: 11488a08-1fe0-a278-2210-deb64731107f@gmx.co.uk
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In the TZ Memory Protection Controller, the BLK_MAX register is supposed
to return the maximum permitted value of the BLK_IDX register. Our
implementation incorrectly returned max+1 (ie the total number of
valid index values, since BLK_IDX is zero-based).
Correct this off-by-one error. Since we consistently initialize
and use s->blk_max throughout the implementation as the 'size'
of the LUT, just adjust the value we return when the guest reads
the BLK_MAX register, rather than trying to change the semantics
of the s->blk_max internal struct field.
Fixes: https://bugs.launchpad.net/qemu/+bug/1806824
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20181213183249.3468-1-peter.maydell@linaro.org
This stubs enables the microbit-micropython firmware to run
on the microbit machine.
Signed-off-by: Steffen Görtz <contrib@steffen-goertz.de>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 20190103091119.9367-12-stefanha@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch adds the model for the nRF51 timer peripheral.
Currently, only the TIMER mode is implemented.
Signed-off-by: Steffen Görtz <contrib@steffen-goertz.de>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 20190103091119.9367-9-stefanha@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This adds a model of the nRF51 GPIO peripheral.
Reference Manual: http://infocenter.nordicsemi.com/pdf/nRF51_RM_v3.0.pdf
The nRF51 series microcontrollers support up to 32 GPIO pins in various configurations.
The pins can be used as input pins with pull-ups or pull-down.
Furthermore, three different output driver modes per level are
available (disconnected, standard, high-current).
The GPIO-Peripheral has a mechanism for detecting level changes which is
not featured in this model.
Signed-off-by: Steffen Görtz <contrib@steffen-goertz.de>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 20190103091119.9367-6-stefanha@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Use RNG in SOC.
Signed-off-by: Steffen Görtz <contrib@steffen-goertz.de>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 20190103091119.9367-5-stefanha@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add a model of the NRF51 random number generator peripheral.
This is a simple random generator that continuously generates
new random values after startup.
Reference Manual: http://infocenter.nordicsemi.com/pdf/nRF51_RM_v3.0.pdf
Signed-off-by: Steffen Görtz <contrib@steffen-goertz.de>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 20190103091119.9367-4-stefanha@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Adds a header that provides definitions that are used
across nRF51 peripherals
Signed-off-by: Steffen Görtz <contrib@steffen-goertz.de>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 20190103091119.9367-3-stefanha@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
From the "A10 User Manual V1.20" p.29: "3.2. Memory Mapping" and:
7. System Control
7.1. Overview
A10 embeds a high-speed SRAM which has been split into five segments.
See detailed memory mapping in following table:
Area Address Size (Bytes)
A1 0x00000000-0x00003FFF 16K
A2 0x00004000-0x00007FFF 16K
A3 0x00008000-0x0000B3FF 13K
A4 0x0000B400-0x0000BFFF 3K
Since for emulation purpose we don't need the segmentations, we simply define
the 'A' area as a single 48KB SRAM.
We don't implement the following others areas:
- 'B': 'Secure RAM' (64K),
- 'C': Debug/ISP SRAM
- 'D': USB SRAM
(qemu) info mtree
address-space: memory
0000000000000000-ffffffffffffffff (prio 0, i/o): system
0000000000000000-000000000000bfff (prio 0, ram): sram A
0000000001c00000-0000000001c00fff (prio -1000, i/o): a10-sram-ctrl
0000000001c0b000-0000000001c0bfff (prio 0, i/o): aw_emac
0000000001c18000-0000000001c18fff (prio 0, i/o): ahci
0000000001c18080-0000000001c180ff (prio 0, i/o): allwinner-ahci
0000000001c20400-0000000001c207ff (prio 0, i/o): allwinner-a10-pic
0000000001c20c00-0000000001c20fff (prio 0, i/o): allwinner-A10-timer
0000000001c28000-0000000001c2801f (prio 0, i/o): serial
0000000040000000-0000000047ffffff (prio 0, ram): cubieboard.ram
Reported-by: Charlie Smurthwaite <charlie@atech.media>
Tested-by: Charlie Smurthwaite <charlie@atech.media>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20190104142921.878-1-f4bug@amsat.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Plug a couple of "board creation time" memory leaks.
Fixes: 6f16da53ff ("hw/arm: versal: Add a virtual Xilinx Versal board")
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190104104749.5314-2-edgar.iglesias@gmail.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This reverts commit 01fd41ab3f.
The generic loader device (-device loader,file=kernel.bin) can be used
to load a kernel instead of the -kernel option. Some boards have flash
memory (pflash) that is set via the -pflash or -drive options.
Allow starting QEMU without the -kernel option to accommodate these
scenarios.
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 20190103144124.18917-1-stefanha@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Create two separate CPU clusters for APUs and RPUs.
Signed-off-by: Luc Michel <luc.michel@greensocs.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20181207090135.7651-17-luc.michel@greensocs.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This commit adds the cpu-cluster type. It aims at gathering CPUs from
the same cluster in a machine.
For now it only has a `cluster-id` property.
Documentation in cluster.h written with the help of Peter Maydell.
Signed-off-by: Luc Michel <luc.michel@greensocs.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20181207090135.7651-2-luc.michel@greensocs.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In previous commit:
commit 7dea29e4af
Author: Li Qiang <liq3ea@gmail.com>
Date: Fri Oct 19 03:50:36 2018 -0700
hw: ccid-card-emulated: cleanup resource when realize in error path
The emulated_realize method was changed so that it jumps to a cleanup
label to de-initialize state upon error. This change failed to ensure
the success path exited the method before this point though. So the
mutexes are always destroyed even in normal operation. The result is
as crashtastic as expected:
$ qemu-system-x86_64 -usb -device usb-ccid,id=ccid0 -device ccid-card-emulated,backend=nss-emulated,id=smartcard0,bus=ccid0.0
qemu-system-x86_64: util/qemu-thread-posix.c:64: qemu_mutex_lock_impl: Assertion `mutex->initialized' failed.
Aborted (core dumped)
Fixes: 7dea29e4af
Reported-by: Michael Tokarev <mjt@tls.msk.ru>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Michael Tokarev <mjt@tls.msk.ru>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20181221134115.27973-1-berrange@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
hostmem-file and hostmem-memfd use the whole object path for the
memory region name, and hostname-ram uses only the path component (the
object id, or canonical path basename):
qemu -m 1024 -object memory-backend-file,id=mem,size=1G,mem-path=/tmp/foo -numa node,memdev=mem -monitor stdio
(qemu) info ramblock
Block Name PSize Offset Used Total
/objects/mem 4 KiB 0x0000000000000000 0x0000000040000000 0x0000000040000000
qemu -m 1024 -object memory-backend-memfd,id=mem,size=1G -numa node,memdev=mem -monitor stdio
(qemu) info ramblock
Block Name PSize Offset Used Total
/objects/mem 4 KiB 0x0000000000000000 0x0000000040000000 0x0000000040000000
qemu -m 1024 -object memory-backend-ram,id=mem,size=1G -numa node,memdev=mem -monitor stdio
(qemu) info ramblock
Block Name PSize Offset Used Total
mem 4 KiB 0x0000000000000000 0x0000000040000000 0x0000000040000000
For consistency, change to use object id for -file and -memfd as well
with >= 4.0.
Having a consistent naming allows to migrate to different hostmem
backends.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: Eduardo Habkost <ehabkost@redhat.com>
It's now possible to use the common function.
Teach object_apply_global_props() to warn if Error argument is NULL.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Acked-by: Eduardo Habkost <ehabkost@redhat.com>
All qdev_prop_register_global() set &error_fatal for errp, except
'-rtc driftfix=slew', which arguably should also use &error_fatal, as
otherwise failing to apply the property would only report a warning.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Acked-by: Eduardo Habkost <ehabkost@redhat.com>
A step towards being able to call a common function,
object_apply_global_props().
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Acked-by: Eduardo Habkost <ehabkost@redhat.com>
All globals are now either provided via -global or through -cpu
features (CPU features are implemented by registering globals).
If the global isn't being used, it should warn in either case.
We can thus consider that all global_props are "user-provided"
globals. No need to track this per-globals anymore.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Acked-by: Eduardo Habkost <ehabkost@redhat.com>
This will allow to apply compat properties on other objects than QDev easily.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: Eduardo Habkost <ehabkost@redhat.com>
Use static arrays instead. I decided to rename the conflicting
pc_compat_2_1() function with pc_compat_2_1_fn().
Suggested-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Acked-by: Eduardo Habkost <ehabkost@redhat.com>
Use static arrays instead. I decided to rename the conflicting
pc_compat_2_1() function with pc_compat_2_1_fn().
Suggested-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Acked-by: Eduardo Habkost <ehabkost@redhat.com>
Use static arrays instead. I decided to rename the conflicting
pc_compat_2_2() function with pc_compat_2_2_fn().
Suggested-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Acked-by: Eduardo Habkost <ehabkost@redhat.com>
Use static arrays instead. I decided to rename the conflicting
pc_compat_2_3() function with pc_compat_2_3_fn().
Suggested-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Acked-by: Eduardo Habkost <ehabkost@redhat.com>
Similarly to accel properties, move compat properties out of globals
registration, and apply the machine compat properties during
device_post_init().
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Acked-by: Eduardo Habkost <ehabkost@redhat.com>
Instead of registering compat properties as globals, let's keep them
in their own array, to avoid mixing with user globals.
Introduce object_apply_global_props() function, to apply compatibility
properties from a GPtrArray.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Acked-by: Eduardo Habkost <ehabkost@redhat.com>
qemu_extra_params_fw[] has external linkage, but is used
only in fw_cfg_bootsplash(), it makes sense to make it
locally.
Signed-off-by: Li Qiang <liq3ea@gmail.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <1542777026-2788-4-git-send-email-liq3ea@gmail.com>
[PMD: Removed qemu_extra_params_fw declaration in vl.c]
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
fw_cfg_reboot() gets option parameter "reboot-timeout" with
qemu_opt_get(), then converts it to an integer by hand. It neglects to
check that conversion for errors, and fails to reject negative values.
Positive values above the limit get reported and replaced by the limit.
This patch checks for conversion errors properly, and reject all values
outside 0...0xffff.
Signed-off-by: Li Qiang <liq3ea@gmail.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <1542777026-2788-3-git-send-email-liq3ea@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
fw_cfg_bootsplash() gets option parameter "splash-time"
with qemu_opt_get(), then converts it to an integer by hand.
It neglects to check that conversion for errors. This is
needlessly complicated and error-prone. But as "splash-time
not specified" is not the same as "splash-time=T" for any T,
we need use qemu_opt_get() to check if splash time exists.
This patch also make the qemu exit when finding or loading
splash file failed.
Signed-off-by: Li Qiang <liq3ea@gmail.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <1542777026-2788-2-git-send-email-liq3ea@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
read_splashfile() reports "failed to read splash file" without
further details. Get the details from g_file_get_contents(), and
include them in the error message. Also remove unnecessary 'res'
variable.
Signed-off-by: Li Qiang <liq3ea@gmail.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <1541052148-28752-1-git-send-email-liq3ea@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
This pull request contains the first set of RISC-V patches I'd like to
target for the 3.2 development cycle. It's really just a collection of
bug fixes with one major new feature: PCIe can now be attached to RISC-V
guests.
This has passed my usual test of booting the latest Linux RC into a
Fedora disk image on the virt machine.
-----BEGIN PGP SIGNATURE-----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=BAOm
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/palmer/tags/riscv-for-master-3.2-part1' into staging
RISC-V Changes for 3.2, Part 1
This pull request contains the first set of RISC-V patches I'd like to
target for the 3.2 development cycle. It's really just a collection of
bug fixes with one major new feature: PCIe can now be attached to RISC-V
guests.
This has passed my usual test of booting the latest Linux RC into a
Fedora disk image on the virt machine.
# gpg: Signature made Fri 21 Dec 2018 16:01:29 GMT
# gpg: using RSA key EF4CA1502CCBAB41
# gpg: Good signature from "Palmer Dabbelt <palmer@dabbelt.com>"
# gpg: aka "Palmer Dabbelt <palmer@sifive.com>"
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 00CE 76D1 8349 60DF CE88 6DF8 EF4C A150 2CCB AB41
* remotes/palmer/tags/riscv-for-master-3.2-part1:
MAINTAINERS: Mark RISC-V as Supported
riscv/cpu: use device_class_set_parent_realize
target/riscv/pmp.c: Fix pmp_decode_napot()
sifive_uart: Implement interrupt pending register
RISC-V: Enable second UART on sifive_e and sifive_u
RISC-V: Fix PLIC pending bitfield reads
RISC-V: Fix CLINT timecmp low 32-bit writes
RISC-V: Add hartid and \n to interrupt logging
sifive_u: Set 'clock-frequency' DT property for SiFive UART
sifive_u: Add clock DT node for GEM ethernet
riscv: Enable VGA and PCIE_VGA
hw/riscv/virt: Connect the gpex PCIe
hw/riscv/virt: Adjust memory layout spacing
hw/riscv/virt: Increase the number of interrupts
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
pvrdma_idx_ring_has_[data/space] routines also return invalid
index PVRDMA_INVALID_IDX[=-1], if ring has no data/space. Check
return value from these routines to avoid plausible infinite loops.
Reported-by: Li Qiang <liq3ea@163.com>
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Reviewed-by: Yuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
With commit 4481985c (rdma: check num_sge does not exceed MAX_SGE)
macro VENDOR_ERR_NO_SGE is no longer in use - delete it.
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Reviewed-by: Yuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
create_cq and create_qp routines allocate ring object, but it's
not released in case of an error, leading to memory leakage.
Reported-by: Li Qiang <liq3ea@163.com>
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Reviewed-by: Yuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
When creating CQ/QP rings, an object can have up to
PVRDMA_MAX_FAST_REG_PAGES 8 pages. Check 'npages' parameter
to avoid excessive memory allocation or a null dereference.
Reported-by: Li Qiang <liq3ea@163.com>
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Reviewed-by: Yuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
rdma back-end has scatter/gather array ibv_sge[MAX_SGE=4] set
to have 4 elements. A guest could send a 'PvrdmaSqWqe' ring element
with 'num_sge' set to > MAX_SGE, which may lead to OOB access issue.
Add check to avoid it.
Reported-by: Saar Amar <saaramar5@gmail.com>
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Reviewed-by: Yuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
If during pvrdma device initialisation an error occurs,
pvrdma_realize() does not release memory resources, leading
to memory leakage.
Reported-by: Li Qiang <liq3ea@163.com>
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Message-Id: <20181212175817.815-1-ppandit@redhat.com>
Reviewed-by: Yuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
When device goes down the function fini_ports loops over all entries in
gid table regardless of the fact whether entry is valid or not. In case
that entry is not valid we'd like to skip from any further processing in
backend device.
Signed-off-by: Yuval Shaia <yuval.shaia@oracle.com>
Reviewed-by: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Signed-off-by: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
bitmap_zero_extend is designed to work for extending, not for
shrinking.
Using g_free instead.
Signed-off-by: Yuval Shaia <yuval.shaia@oracle.com>
Reviewed-by: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Signed-off-by: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
In order to clean some external resources such as GIDs, QPs etc,
register to receive notification when VM is shutdown.
Signed-off-by: Yuval Shaia <yuval.shaia@oracle.com>
Reviewed-by: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Signed-off-by: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Device supports only one port, let's remove a dead code that handles
more than one port.
Signed-off-by: Yuval Shaia <yuval.shaia@oracle.com>
Reviewed-by: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Signed-off-by: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Driver checks error code let's set it.
In addition, for code simplification purposes, set response's fields
ack, response and err outside of the scope of command handlers.
Signed-off-by: Yuval Shaia <yuval.shaia@oracle.com>
Reviewed-by: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Signed-off-by: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Add ability to pass specific WC attributes to CQE such as GRH_BIT flag.
Signed-off-by: Yuval Shaia <yuval.shaia@oracle.com>
Reviewed-by: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Signed-off-by: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
User should be able to control the device by changing Ethernet function
state so if user runs 'ifconfig ens3 down' the PVRDMA function should be
down as well.
Signed-off-by: Yuval Shaia <yuval.shaia@oracle.com>
Reviewed-by: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Signed-off-by: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
node_guid should be set once device is load.
Make node_guid be GID format (32 bit) of PCI function 0 vmxnet3 device's
MAC.
A new function was added to do the conversion.
So for example the MAC 56:b6:44:e9:62:dc will be converted to GID
54b6:44ff:fee9:62dc.
Signed-off-by: Yuval Shaia <yuval.shaia@oracle.com>
Reviewed-by: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Signed-off-by: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
pvrdma setup requires vmxnet3 device on PCI function 0 and PVRDMA device
on PCI function 1.
pvrdma device needs to access vmxnet3 device object for several reasons:
1. Make sure PCI function 0 is vmxnet3.
2. To monitor vmxnet3 device state.
3. To configure node_guid accoring to vmxnet3 device's MAC address.
To be able to access vmxnet3 device the definition of VMXNET3State is
moved to a new header file.
Signed-off-by: Yuval Shaia <yuval.shaia@oracle.com>
Reviewed-by: Dmitry Fleytman <dmitry.fleytman@gmail.com>
Signed-off-by: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
The control over the RDMA device's GID table is done by updating the
device's Ethernet function addresses.
Usually the first GID entry is determined by the MAC address, the second
by the first IPv6 address and the third by the IPv4 address. Other
entries can be added by adding more IP addresses. The opposite is the
same, i.e. whenever an address is removed, the corresponding GID entry
is removed.
The process is done by the network and RDMA stacks. Whenever an address
is added the ib_core driver is notified and calls the device driver
add_gid function which in turn update the device.
To support this in pvrdma device we need to hook into the create_bind
and destroy_bind HW commands triggered by pvrdma driver in guest.
Whenever a change is made to the pvrdma port's GID table a special QMP
message is sent to be processed by libvirt to update the address of the
backend Ethernet device.
Signed-off-by: Yuval Shaia <yuval.shaia@oracle.com>
Reviewed-by: Marcel Apfelbaum<marcel.apfelbaum@gmail.com>
Signed-off-by: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
opcode for WC should be set by the device and not taken from work
element.
Signed-off-by: Yuval Shaia <yuval.shaia@oracle.com>
Reviewed-by: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Signed-off-by: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
The function pvrdma_post_cqe populates CQE entry with opcode from the
given completion element. For receive operation value was not set. Fix
it by setting it to IBV_WC_RECV.
Signed-off-by: Yuval Shaia <yuval.shaia@oracle.com>
Reviewed-by: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Signed-off-by: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
MAD (Management Datagram) packets are widely used by various modules
both in kernel and in user space for example the rdma_* API which is
used to create and maintain "connection" layer on top of RDMA uses
several types of MAD packets.
For more information please refer to chapter 13.4 in Volume 1
Architecture Specification, Release 1.1 available here:
https://www.infinibandta.org/ibta-specifications-download/
To support MAD packets the device uses an external utility
(contrib/rdmacm-mux) to relay packets from and to the guest driver.
Signed-off-by: Yuval Shaia <yuval.shaia@oracle.com>
Reviewed-by: Marcel Apfelbaum<marcel.apfelbaum@gmail.com>
Signed-off-by: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Upon completion of incoming packet the device pushes CQE to driver's RX
ring and notify the driver (msix).
While for data-path incoming packets the driver needs the ability to
control whether it wished to receive interrupts or not, for control-path
packets such as incoming MAD the driver needs to be notified anyway, it
even do not need to re-arm the notification bit.
Enhance the notification field to support this.
Signed-off-by: Yuval Shaia <yuval.shaia@oracle.com>
Reviewed-by: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Signed-off-by: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Return value of 0 means ok, we want to free the memory only in case of
error.
Signed-off-by: Yuval Shaia <yuval.shaia@oracle.com>
Message-Id: <20181025061700.17050-1-yuval.shaia@oracle.com>
Reviewed-by: Marcel Apfelbaum<marcel.apfelbaum@gmail.com>
Signed-off-by: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
This pull request supersedes the one from 2018-12-13.
This is a revised first ppc pull request for qemu-4.0. Highlights
are:
* Most of the code for the POWER9 "XIVE" interrupt controller
(not complete yet, but we're getting there)
* A number of g_new vs. g_malloc cleanups
* Some IRQ wiring cleanups
* A fix for how we advertise NUMA nodes to the guest for pseries
-----BEGIN PGP SIGNATURE-----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=IN1s
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dgibson/tags/ppc-for-4.0-20181221' into staging
ppc patch queue 2018-12-21
This pull request supersedes the one from 2018-12-13.
This is a revised first ppc pull request for qemu-4.0. Highlights
are:
* Most of the code for the POWER9 "XIVE" interrupt controller
(not complete yet, but we're getting there)
* A number of g_new vs. g_malloc cleanups
* Some IRQ wiring cleanups
* A fix for how we advertise NUMA nodes to the guest for pseries
# gpg: Signature made Fri 21 Dec 2018 05:34:12 GMT
# gpg: using RSA key 6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>"
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>"
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>"
# gpg: aka "David Gibson (kernel.org) <dwg@kernel.org>"
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dgibson/tags/ppc-for-4.0-20181221: (40 commits)
MAINTAINERS: PPC: add a XIVE section
spapr: change default CPU type to POWER9
spapr: introduce an 'ic-mode' machine option
spapr: add an extra OV5 field to the sPAPR IRQ backend
spapr: add a 'reset' method to the sPAPR IRQ backend
spapr: extend the sPAPR IRQ backend for XICS migration
spapr: allocate the interrupt thread context under the CPU core
spapr: add device tree support for the XIVE exploitation mode
spapr: add hcalls support for the XIVE exploitation interrupt mode
spapr: introduce a new machine IRQ backend for XIVE
spapr-iommu: Always advertise the maximum possible DMA window size
spapr/xive: use the VCPU id as a NVT identifier
spapr/xive: introduce a XIVE interrupt controller
ppc/xive: notify the CPU when the interrupt priority is more privileged
ppc/xive: introduce a simplified XIVE presenter
ppc/xive: introduce the XIVE interrupt thread context
ppc/xive: add support for the END Event State Buffers
Changes requirement for "vsubsbs" instruction
spapr: export and rename the xics_max_server_number() routine
spapr: introduce a spapr_irq_init() routine
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
VTD fixes
IR and split irqchip are now the default for Q35
ACPI refactoring
hotplug refactoring
new names for virtio devices
multiple pcie link width/speeds
PCI fixes
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJcG967AAoJECgfDbjSjVRpUlMH/1wy8WW7Br/4JxlWUPsfZTqZ
0Lg2n59wuFzRVS+gLotp6bUaJGR9xn9fKjI1wfD59oVrDTKyauuw82v0OityEs33
ZquFecuJvP6k5N40DkqA9YJjKSw7nUmLrsyrD0t2H43npikP2aD9f6yootrr3oVV
nPwBvyT9ykIBQc7IzsHDiLw3EPdIf+9IR7+l+PLptzV0zK43Jfwi/nzHIQq00UMz
eLM/ejQLIx4BZJnYGS0Cy6v3K7cS3k45LHDY0cGc0id2jHFN2vdQyHCF9I1ps72q
pSlhMaLEwvQSYyre6iFTG5uuvyIPWv3LOkaBEwMSA5B/HXuEb2RKHThYzS9dc68=
=OwW7
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
pci, pc, virtio: fixes, features
VTD fixes
IR and split irqchip are now the default for Q35
ACPI refactoring
hotplug refactoring
new names for virtio devices
multiple pcie link width/speeds
PCI fixes
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Thu 20 Dec 2018 18:26:03 GMT
# gpg: using RSA key 281F0DB8D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>"
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>"
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* remotes/mst/tags/for_upstream: (44 commits)
x86-iommu: turn on IR by default if proper
x86-iommu: switch intr_supported to OnOffAuto type
q35: set split kernel irqchip as default
pci: Adjust PCI config limit based on bus topology
spapr_pci: perform unplug via the hotplug handler
pci/shpc: perform unplug via the hotplug handler
pci: Reuse pci-bridge hotplug handler handlers for pcie-pci-bridge
pci/pcie: perform unplug via the hotplug handler
pci/pcihp: perform unplug via the hotplug handler
pci/pcihp: overwrite hotplug handler recursively from the start
pci/pcihp: perform check for bus capability in pre_plug handler
s390x/pci: rename hotplug handler callbacks
pci/shpc: rename hotplug handler callbacks
pci/pcie: rename hotplug handler callbacks
hw/i386: Remove deprecated machines pc-0.10 and pc-0.11
hw: acpi: Remove AcpiRsdpDescriptor and fix tests
hw: acpi: Export and share the ARM RSDP build
hw: arm: Support both legacy and current RSDP build
hw: arm: Convert the RSDP build to the buid_append_foo() API
hw: arm: Carry RSDP specific data through AcpiRsdpData
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This option is used to select the interrupt controller mode (XICS or
XIVE) with which the machine will operate. XICS being the default
mode for now.
When running a machine with the XIVE interrupt mode backend, the guest
OS is required to have support for the XIVE exploitation mode. In the
case of legacy OS, the mode selected by CAS should be XICS and the OS
should fail to boot. However, QEMU could possibly detect it, terminate
the boot process and reset to stop in the SLOF firmware. This is not
yet handled.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The interrupt modes supported by the hypervisor are advertised to the
guest with new bits definitions of the option vector 5 of property
"ibm,arch-vec-5-platform-support. The byte 23 bits 0-1 of the OV5 are
defined as follow :
0b00 PAPR 2.7 and earlier (Legacy systems)
0b01 XIVE Exploitation mode only
0b10 Either available
If the client/guest selects the XIVE interrupt mode, it informs the
hypervisor by returning the value 0b01 in byte 23 bits 0-1. A 0b00
value indicates the use of the XICS interrupt mode (Legacy systems).
The sPAPR IRQ backend is extended with these definitions and the
values are directly used to populate the "ibm,arch-vec-5-platform-support"
property. The interrupt mode is advertised under TCG and under KVM.
Although a KVM XIVE device is not yet available, the machine can still
operate with kernel_irqchip=off. However, we apply a restriction on
the CPU which is required to be a POWER9 when a XIVE interrupt
controller is in use.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
For the time being, the XIVE reset handler updates the OS CAM line of
the vCPU as it is done under a real hypervisor when a vCPU is
scheduled to run on a HW thread. This will let the XIVE presenter
engine find a match among the NVTs dispatched on the HW threads.
This handler will become even more useful when we introduce the
machine supporting both interrupt modes, XIVE and XICS. In this
machine, the interrupt mode is chosen by the CAS negotiation process
and activated after a reset.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
[dwg: Fix style nits]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Introduce a new sPAPR IRQ handler to handle resend after migration
when the machine is using a KVM XICS interrupt controller model.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Each interrupt mode has its own specific interrupt presenter object,
that we store under the CPU object, one for XICS and one for XIVE.
Extend the sPAPR IRQ backend with a new handler to support them both.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The XIVE interface for the guest is described in the device tree under
the "interrupt-controller" node. A couple of new properties are
specific to XIVE :
- "reg"
contains the base address and size of the thread interrupt
managnement areas (TIMA), for the User level and for the Guest OS
level. Only the Guest OS level is taken into account today.
- "ibm,xive-eq-sizes"
the size of the event queues. One cell per size supported, contains
log2 of size, in ascending order.
- "ibm,xive-lisn-ranges"
the IRQ interrupt number ranges assigned to the guest for the IPIs.
and also under the root node :
- "ibm,plat-res-int-priorities"
contains a list of priorities that the hypervisor has reserved for
its own use. OPAL uses the priority 7 queue to automatically
escalate interrupts for all other queues (DD2.X POWER9). So only
priorities [0..6] are allowed for the guest.
Extend the sPAPR IRQ backend with a new handler to populate the DT
with the appropriate "interrupt-controller" node.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
[dwg: Fix style nits]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The different XIVE virtualization structures (sources and event queues)
are configured with a set of Hypervisor calls :
- H_INT_GET_SOURCE_INFO
used to obtain the address of the MMIO page of the Event State
Buffer (ESB) entry associated with the source.
- H_INT_SET_SOURCE_CONFIG
assigns a source to a "target".
- H_INT_GET_SOURCE_CONFIG
determines which "target" and "priority" is assigned to a source
- H_INT_GET_QUEUE_INFO
returns the address of the notification management page associated
with the specified "target" and "priority".
- H_INT_SET_QUEUE_CONFIG
sets or resets the event queue for a given "target" and "priority".
It is also used to set the notification configuration associated
with the queue, only unconditional notification is supported for
the moment. Reset is performed with a queue size of 0 and queueing
is disabled in that case.
- H_INT_GET_QUEUE_CONFIG
returns the queue settings for a given "target" and "priority".
- H_INT_RESET
resets all of the guest's internal interrupt structures to their
initial state, losing all configuration set via the hcalls
H_INT_SET_SOURCE_CONFIG and H_INT_SET_QUEUE_CONFIG.
- H_INT_SYNC
issue a synchronisation on a source to make sure all notifications
have reached their queue.
Calls that still need to be addressed :
H_INT_SET_OS_REPORTING_LINE
H_INT_GET_OS_REPORTING_LINE
See the code for more documentation on each hcall.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
[dwg: Folded in fix for field accessors]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The XIVE IRQ backend uses the same layout as the new XICS backend but
covers the full range of the IRQ number space. The IRQ numbers for the
CPU IPIs are allocated at the bottom of this space, below 4K, to
preserve compatibility with XICS which does not use that range.
This should be enough given that the maximum number of CPUs is 1024
for the sPAPR machine under QEMU. For the record, the biggest POWER8
or POWER9 system has a maximum of 1536 HW threads (16 sockets, 192
cores, SMT8).
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
When deciding about the huge DMA window, the typical Linux pseries guest
uses the maximum allowed RAM size as the upper limit. We did the same
on QEMU side to match that logic. Now we are going to support a GPU RAM
pass through which is not available at the guest boot time as it requires
the guest driver interaction. As the result, the guest requests a smaller
window than it should. Therefore the guest needs to be patched to
understand this new memory and so does QEMU.
Instead of reimplementing here whatever solution we choose for the guest,
this advertises the biggest possible window size limited by 32 bit
(as defined by LoPAPR). Since the window size has to be power-of-two
(the create rtas call receives a window shift, not a size),
this uses 0x8000.0000 as the maximum number of TCEs possible (rather than
32bit maximum of 0xffff.ffff).
This is safe as:
1. The guest visible emulated table is allocated in KVM (actual pages
are allocated in page fault handler) and QEMU (actual pages are allocated
when updated);
2. The hardware table (and corresponding userspace address table)
supports sparse allocation and also checks for locked_vm limit so
it is unable to cause the host any damage.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Pierre Morel
David Hildenbrand
Li Qiang
Philippe Mathieu-Daudé
Yang Zhong
Marc-André Lureau
Stefan Berger
Fei Li
Eduardo Habkost
Juan Quintela
Yuri Benditovich
Jian Wang
Thomas Huth
Dongli Zhang
Peter Maydell
Paolo Bonzini
Borislav Petkov
Tim Smith
Anthony PERARD
Paul Durrant
Zhao Yan
Peng Hao
Guenter Roeck
Gerd Hoffmann
Wainer dos Santos Moschetta
Cédric Le Goater
Greg Kurz
Michael Roth
BALATON Zoltan
Alexey Kardashevskiy
Laurent Vivier
Hongbo Zhang
Jonathan Davies
Nick Hudson
Steffen Görtz
Philippe Mathieu-Daudé
Edgar E. Iglesias
Stefan Hajnoczi
Luc Michel
Daniel P. Berrangé
Li Qiang
Prasad J Pandit
Yuval Shaia