eth_strip_vlan and eth_strip_vlan_ex refers to ehdr_buf as struct
eth_header. Enforce alignment for the structure.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Sriram Yagnaraman <sriram.yagnaraman@est.tech>
Signed-off-by: Jason Wang <jasowang@redhat.com>
igb does not properly ensure the buffer passed to
net_rx_pkt_set_protocols() is contiguous for the entire L2/L3/L4 header.
Allow it to pass scattered data to net_rx_pkt_set_protocols().
Fixes: 3a977deebe ("Intrdocue igb device emulation")
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Sriram Yagnaraman <sriram.yagnaraman@est.tech>
Signed-off-by: Jason Wang <jasowang@redhat.com>
igb, a new network device emulation, will need SCTP checksum offloading.
Currently eth_get_protocols() has a bool parameter for each protocol
currently it supports, but there will be a bit too many parameters if
we add yet another protocol.
Introduce an enum type, EthL4HdrProto to represent all L4 protocols
eth_get_protocols() support with one parameter.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
The values returned by eth_get_protocols() are used to perform RSS,
checksumming and segmentation. Even when a packet signals the use of the
protocols which these operations can be applied to, the headers for them
may not be present because of too short packet or fragmentation, for
example. In such a case, the operations cannot be applied safely.
Report the presence of headers instead of whether the use of the
protocols are indicated with eth_get_protocols(). This also makes
corresponding changes to the callers of eth_get_protocols() to match
with its new signature and to remove redundant checks for fragmentation.
Fixes: 75020a7021 ("Common definitions for VMWARE devices")
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
e1000e didn't perform software segmentation for loopback if virtio-net
header is enabled, which is wrong.
To fix the problem, introduce net_tx_pkt_send_custom(), which allows the
caller to specify whether offloading should be assumed or not.
net_tx_pkt_send_custom() also allows the caller to provide a custom
sending function. Packets with virtio-net headers and ones without
virtio-net headers will be provided at the same time so the function
can choose the preferred version. In case of e1000e loopback, it prefers
to have virtio-net headers as they allows to skip the checksum
verification if VIRTIO_NET_HDR_F_DATA_VALID is set.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
When virtio-net header is not set, net_rx_pkt_get_vhdr() returns
zero-filled virtio_net_hdr, which is actually valid. In fact, tap device
uses zero-filled virtio_net_hdr when virtio-net header is not provided
by the peer. Therefore, we can just remove net_rx_pkt_has_virt_hdr() and
always assume NetTxPkt has a valid virtio-net header.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
When requested to calculate the hash for TCPV6 packet,
ignore overrides of source and destination addresses
in in extension headers.
Use these overrides when new hash type NetPktRssIpV6TcpEx
requested.
Use this type in e1000e hash calculation for IPv6 TCP, which
should take in account overrides of the addresses.
Signed-off-by: Yuri Benditovich <yuri.benditovich@daynix.com>
Acked-by: Dmitry Fleytman <dmitry.fleytman@gmail.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Add support for following hash types:
IPV6 TCP with extension headers
IPV4 UDP
IPV6 UDP
IPV6 UDP with extension headers
Signed-off-by: Yuri Benditovich <yuri.benditovich@daynix.com>
Acked-by: Dmitry Fleytman <dmitry.fleytman@gmail.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
The checksum algorithm used by IPv4, TCP and UDP allows a zero value
to be represented by either 0x0000 and 0xFFFF. But per RFC 768, a zero
UDP checksum must be transmitted as 0xFFFF because 0x0000 is a special
value meaning no checksum.
Substitute 0xFFFF whenever a checksum is computed as zero when
modifying a UDP datagram header. Doing this on IPv4 and TCP checksums
is unnecessary but legal. Add a wrapper for net_checksum_finish() that
makes the substitution.
(We can't just change net_checksum_finish(), as that function is also
used by receivers to verify checksums, and in that case the expected
value is always 0x0000.)
Signed-off-by: Ed Swierk <eswierk@skyportsystems.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
This is a refactoring commit that does not change behavior.
Signed-off-by: Dmitry Fleytman <dmitry@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
In case of VLAN stripping ETH header is stored in a
separate chunk and length of IOV should take this into
account.
This patch fixes checksum validation for RX packets
with VLAN header.
Devices affected by this problem: e1000e and vmxnet3.
Cc: qemu-stable@nongnu.org
Signed-off-by: Dmitry Fleytman <dmitry@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
In case of VLAN stripping, ETH header put into a
separate buffer, therefore amont of data copied
from original IOV should be smaller.
Cc: qemu-stable@nongnu.org
Signed-off-by: Dmitry Fleytman <dmitry@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
This patch fixed a problem that was introduced in commit eb700029.
When net_rx_pkt_attach_iovec() calls eth_strip_vlan()
this can result in pkt->ehdr_buf being overflowed, because
ehdr_buf is only sizeof(struct eth_header) bytes large
but eth_strip_vlan() can write
sizeof(struct eth_header) + sizeof(struct vlan_header)
bytes into it.
Devices affected by this problem: vmxnet3.
Cc: qemu-stable@nongnu.org
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Dmitry Fleytman <dmitry@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
This has been pointless since commit 605d52e62, which was a
search-and-replace, overlooked the redundancy.
Signed-off-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Dmitry Fleytman <dmitry@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
This patch extends the TX/RX packet abstractions with features that will
be used by the e1000e device implementation.
Changes are:
1. Support iovec lists for RX buffers
2. Deeper RX packets parsing
3. Loopback option for TX packets
4. Extended VLAN headers handling
5. RSS processing for RX packets
Signed-off-by: Dmitry Fleytman <dmitry.fleytman@ravellosystems.com>
Signed-off-by: Leonid Bloch <leonid.bloch@ravellosystems.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
This patch drops "vmx" prefix from packet abstractions names
to emphasize the fact they are generic and not tied to any
specific network device.
These abstractions will be reused by e1000e emulation implementation
introduced by following patches so their names need generalization.
This patch (except renamed files, adjusted comments and changes in MAINTAINTERS)
was produced by:
git grep -lz 'vmxnet_tx_pkt' | xargs -0 perl -i'' -pE "s/vmxnet_tx_pkt/net_tx_pkt/g"
git grep -lz 'vmxnet_rx_pkt' | xargs -0 perl -i'' -pE "s/vmxnet_rx_pkt/net_rx_pkt/g"
git grep -lz 'VmxnetTxPkt' | xargs -0 perl -i'' -pE "s/VmxnetTxPkt/NetTxPkt/g"
git grep -lz 'VMXNET_TX_PKT' | xargs -0 perl -i'' -pE "s/VMXNET_TX_PKT/NET_TX_PKT/g"
git grep -lz 'VmxnetRxPkt' | xargs -0 perl -i'' -pE "s/VmxnetRxPkt/NetRxPkt/g"
git grep -lz 'VMXNET_RX_PKT' | xargs -0 perl -i'' -pE "s/VMXNET_RX_PKT/NET_RX_PKT/g"
sed -ie 's/VMXNET_/NET_/g' hw/net/vmxnet_rx_pkt.c
sed -ie 's/VMXNET_/NET_/g' hw/net/vmxnet_tx_pkt.c
Signed-off-by: Dmitry Fleytman <dmitry.fleytman@ravellosystems.com>
Signed-off-by: Leonid Bloch <leonid.bloch@ravellosystems.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
