The fact that the MMIO handler is not re-entrant causes an infinite
loop under certain conditions:
Guest write to TDT -> Loopback -> RX (DMA to TDT) -> TX
We now eliminate the effect of this problem locally in e1000, by adding
a boolean in struct E1000State indicating when the TX side is busy. This
will cause any entering new call to return early instead of interfering
with the ongoing work, and eliminates any risk of looping.
This is intended to address CVE-2021-20257.
Signed-off-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
The initial value of VLAN Ether Type (VET) register is 0x8100, as per
the manual and real hardware.
While Linux e1000 driver always writes VET register to 0x8100, it is
not always the case for everyone. Drivers relying on the reset value
of VET won't be able to transmit and receive VLAN frames in QEMU.
Reported-by: Markus Carlstedt <markus.carlstedt@windriver.com>
Signed-off-by: Christina Wang <christina.wang@windriver.com>
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
This patch switches to use qemu_receive_packet() which can detect
reentrancy and return early.
This is intended to address CVE-2021-3416.
Cc: Prasad J Pandit <ppandit@redhat.com>
Cc: qemu-stable@nongnu.org
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
During procss_tx_desc(), driver can try to chain data descriptor with
legacy descriptor, when will lead underflow for the following
calculation in process_tx_desc() for bytes:
if (tp->size + bytes > msh)
bytes = msh - tp->size;
This will lead a infinite loop. So check and fail early if tp->size if
greater or equal to msh.
Reported-by: Alexander Bulekov <alxndr@bu.edu>
Reported-by: Cheolwoo Myung <cwmyung@snu.ac.kr>
Reported-by: Ruhr-University Bochum <bugs-syssec@rub.de>
Cc: Prasad J Pandit <ppandit@redhat.com>
Cc: qemu-stable@nongnu.org
Signed-off-by: Jason Wang <jasowang@redhat.com>
This commit is the result of running the timer-del-timer-free.cocci
script on the whole source tree.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Corey Minyard <cminyard@mvista.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20201215154107.3255-4-peter.maydell@linaro.org
There is no "version 2" of the "Lesser" General Public License.
It is either "GPL version 2.0" or "Lesser GPL version 2.1".
This patch replaces all occurrences of "Lesser GPL version 2" with
"Lesser GPL version 2.1" in comment section.
This patch contains all the files, whose maintainer I could not get
from ‘get_maintainer.pl’ script.
Signed-off-by: Chetan Pant <chetan4windows@gmail.com>
Message-Id: <20201023124424.20177-1-chetan4windows@gmail.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
[thuth: Adapted exec.c and qdev-monitor.c to new location]
Signed-off-by: Thomas Huth <thuth@redhat.com>
Some typedefs and macros are defined after the type check macros.
This makes it difficult to automatically replace their
definitions with OBJECT_DECLARE_TYPE.
Patch generated using:
$ ./scripts/codeconverter/converter.py -i \
--pattern=QOMStructTypedefSplit $(git grep -l '' -- '*.[ch]')
which will split "typdef struct { ... } TypedefName"
declarations.
Followed by:
$ ./scripts/codeconverter/converter.py -i --pattern=MoveSymbols \
$(git grep -l '' -- '*.[ch]')
which will:
- move the typedefs and #defines above the type check macros
- add missing #include "qom/object.h" lines if necessary
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20200831210740.126168-9-ehabkost@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20200831210740.126168-10-ehabkost@redhat.com>
Message-Id: <20200831210740.126168-11-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Rename the E1000_DEVICE_CLASS() and E1000_DEVICE_GET_CLASS()
macros to be consistent with the E1000() instance cast macro.
This will allow us to register the type cast macros using
OBJECT_DECLARE_TYPE later.
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Tested-By: Roman Bolshakov <r.bolshakov@yadro.com>
Message-Id: <20200825192110.3528606-2-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Several functions can't fail anymore: ich9_pm_add_properties(),
device_add_bootindex_property(), ppc_compat_add_property(),
spapr_caps_add_properties(), PropertyInfo.create(). Drop their @errp
parameter.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20200505152926.18877-16-armbru@redhat.com>
QOM object initialization runs .instance_init() for the type and all
its supertypes; see object_init_with_type().
Both TYPE_E1000_BASE and its concrete subtypes set .instance_init() to
e1000_instance_init(). For the concrete subtypes, it duly gets run
twice. The second run fails, but the error gets ignored (a later
commit will change that).
Remove it from the subtypes.
Cc: Jason Wang <jasowang@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20200505152926.18877-12-armbru@redhat.com>
The NetCanReceive handler return whether the device can or
can not receive new packets. Make it obvious by returning
a boolean type.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Each array consumes 256KiB of .data. As we do not reassign entries,
we can move it to the .rodata section, and save a total of 1MiB of
.data (size reported on x86_64 host).
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Dmitry Fleytman <dmitry.fleytman@gmail.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Message-Id: <20200305010446.17029-3-philmd@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Missed during the QOM convertion in 9af21dbee1.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Message-Id: <20190715102210.31365-1-philmd@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
In my "build everything" tree, changing hw/qdev-properties.h triggers
a recompile of some 2700 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).
Many places including hw/qdev-properties.h (directly or via hw/qdev.h)
actually need only hw/qdev-core.h. Include hw/qdev-core.h there
instead.
hw/qdev.h is actually pointless: all it does is include hw/qdev-core.h
and hw/qdev-properties.h, which in turn includes hw/qdev-core.h.
Replace the remaining uses of hw/qdev.h by hw/qdev-properties.h.
While there, delete a few superfluous inclusions of hw/qdev-core.h.
Touching hw/qdev-properties.h now recompiles some 1200 objects.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Daniel P. Berrangé" <berrange@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20190812052359.30071-22-armbru@redhat.com>
In my "build everything" tree, changing hw/hw.h triggers a recompile
of some 2600 out of 6600 objects (not counting tests and objects that
don't depend on qemu/osdep.h).
The previous commits have left only the declaration of hw_error() in
hw/hw.h. This permits dropping most of its inclusions. Touching it
now recompiles less than 200 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190812052359.30071-19-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
In my "build everything" tree, changing migration/vmstate.h triggers a
recompile of some 2700 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).
hw/hw.h supposedly includes it for convenience. Several other headers
include it just to get VMStateDescription. The previous commit made
that unnecessary.
Include migration/vmstate.h only where it's still needed. Touching it
now recompiles only some 1600 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190812052359.30071-16-armbru@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
We should not raise any interrupt after VM has been stopped but this
is what e1000 currently did when mit timer is active in
pre_save(). Fixing this by scheduling a timer in post_load() which can
make sure the interrupt was raised when VM is running.
Reported-and-tested-by: Longpeng <longpeng2@huawei.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
In situations where e1000 receives an undersized Ethernet frame,
QEMU increments the emulated "Receive Undersize Count (RUC)"
register when padding the frame.
This is incorrect because this an expected scenario (e.g. with
VLAN tag stripping) and not an error. As such, QEMU should not
increment the emulated RUC.
Fixes: 3b27430177 ("e1000: Implementing various counters")
Reviewed-by: Mark Kanda <mark.kanda@oracle.com>
Reviewed-by: Bhavesh Davda <bhavesh.davda@oracle.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Chris Kenna <chris.kenna@oracle.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
The e1000 emulation silently discards RX packets if there's
insufficient space in the ring buffer. This leads to errors
on higher-level protocols in the guest, with no indication
about the error cause.
This patch increments the "Missed Packets Count" (MPC) and
"Receive No Buffers Count" (RNBC) HW counters in this case.
As the emulation has no FIFO for buffering packets that can't
immediately be pushed to the guest, these two registers are
practically equivalent (see 10.2.7.4, 10.2.7.33 in
https://www.intel.com/content/www/us/en/embedded/products/networking/82574l-gbe-controller-datasheet.html).
On a Linux guest, the register content will be reflected in
the "rx_missed_errors" and "rx_no_buffer_count" stats from
"ethtool -S", and in the "missed" stat from "ip -s -s link show",
giving at least some hint about the error cause inside the guest.
If the cause is known, problems like this can often be avoided
easily, by increasing the number of RX descriptors in the guest
e1000 driver (e.g under Linux, "e1000.RxDescriptors=1024").
The patch also adds a qemu trace message for this condition.
Signed-off-by: Martin Wilck <mwilck@suse.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
When we're using the subsection we migrate both
the 'props' and 'tso_props' data; when we're not using
the subsection (to migrate to 2.11 or old machine types) we've
got to choose what to migrate in the main structure.
If we're using the subsection migrate 'props' in the main structure.
If we're not using the subsection then migrate the last one
that changed, which gives behaviour similar to the old behaviour.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Swing the tx.props out via a temporary structure, so in future patches
we can select what we're going to send.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Wire the new subsection from the previous commit to a property
so we can turn it off easily.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Old QEMUs only had one set of offload data; when we only receive
one lot, dupe the received data - that should give us about the
same bug level as the old version.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
A bunch of new TSO fields were introduced by d62644b4 and this bumped
the VMState version; however it's easier for those trying to keep
backwards migration compatibility if these fields are added in a
subsection instead.
Move the new fields to a subsection.
Since this was added after 2.11, this change will only affect
compatbility with 2.12-rc0.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Headers like "hw/loader.h" and "qemu/sockets.h" are not needed in
the hw/net/*.c files. And Some other headers are included via other
headers already, so we can drop them, too.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
The device is supposed to maintain two distinct contexts for transmit
offloads: one has parameters for both segmentation and checksum
offload, the other only for checksum offload. The guest driver can
send two context descriptors, one for each context (the TSE flag
specifies which). Then the guest can refer to one or the other context
in subsequent transmit data descriptors, depending on what offloads it
wants applied to each packet.
Currently the e1000 device stores just one context, and misinterprets
the TSE flags in the context and data descriptors. This is often okay:
Linux happens to send a fresh context descriptor before every data
descriptor, so forgetting the other context doesn't matter. Windows
does rely on separate contexts for TSO vs. non-TSO packets, but for
mostly-TCP traffic the two contexts have identical TCP-specific
offload parameters so confusing them doesn't matter.
One case where this confusion matters is when a Windows guest sets up
a TSO context for TCP and a non-TSO context for UDP, and then
transmits both TCP and UDP traffic in parallel. The e1000 device
sometimes ends up using TCP-specific parameters while doing checksum
offload on a UDP datagram: it writes the checksum to offset 16 (the
correct location for a TCP checksum), stomping on two bytes of UDP
data, and leaving the wrong value in the actual UDP checksum field at
offset 6. (Even worse, the host network stack may then recompute the
UDP checksum, "correcting" it to match the corrupt data before sending
it out a physical interface.)
Correct this by tracking the TSO context independently of the non-TSO
context, and selecting the appropriate context based on the TSE flag
in each transmit data descriptor.
Signed-off-by: Ed Swierk <eswierk@skyportsystems.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
sum_needed and cptse flags are received from the guest within each
transmit data descriptor. They are not part of the offload context;
instead, they determine how to apply a previously received context to
the packet being transmitted:
- If cptse is set, perform both segmentation and checksum offload
using the parameters in the TSO context; otherwise just do checksum
offload. (Currently the e1000 device incorrectly stores only one
context, which will be fixed in a subsequent patch.)
- Depending on the bits set in sum_needed, possibly perform L4
checksum offload and/or IP checksum offload, using the parameters in
the appropriate context.
Move these flags out of struct e1000x_txd_props, which is otherwise
dedicated to storing values from a context descriptor, and into the
per-packet TX struct.
Signed-off-by: Ed Swierk <eswierk@skyportsystems.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
The checksum algorithm used by IPv4, TCP and UDP allows a zero value
to be represented by either 0x0000 and 0xFFFF. But per RFC 768, a zero
UDP checksum must be transmitted as 0xFFFF because 0x0000 is a special
value meaning no checksum.
Substitute 0xFFFF whenever a checksum is computed as zero when
modifying a UDP datagram header. Doing this on IPv4 and TCP checksums
is unnecessary but legal. Add a wrapper for net_checksum_finish() that
makes the substitution.
(We can't just change net_checksum_finish(), as that function is also
used by receivers to verify checksums, and in that case the expected
value is always 0x0000.)
Signed-off-by: Ed Swierk <eswierk@skyportsystems.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Add INTERFACE_CONVENTIONAL_PCI_DEVICE to all direct subtypes of
TYPE_PCI_DEVICE, except:
1) The ones that already have INTERFACE_PCIE_DEVICE set:
* base-xhci
* e1000e
* nvme
* pvscsi
* vfio-pci
* virtio-pci
* vmxnet3
2) base-pci-bridge
Not all PCI bridges are Conventional PCI devices, so
INTERFACE_CONVENTIONAL_PCI_DEVICE is added only to the subtypes
that are actually Conventional PCI:
* dec-21154-p2p-bridge
* i82801b11-bridge
* pbm-bridge
* pci-bridge
The direct subtypes of base-pci-bridge not touched by this patch
are:
* xilinx-pcie-root: Already marked as PCIe-only.
* pcie-pci-bridge: Already marked as PCIe-only.
* pcie-port: all non-abstract subtypes of pcie-port are already
marked as PCIe-only devices.
3) megasas-base
Not all megasas devices are Conventional PCI devices, so the
interface names are added to the subclasses registered by
megasas_register_types(), according to information in the
megasas_devices[] array.
"megasas-gen2" already implements INTERFACE_PCIE_DEVICE, so add
INTERFACE_CONVENTIONAL_PCI_DEVICE only to "megasas".
Acked-by: Alberto Garcia <berto@igalia.com>
Acked-by: John Snow <jsnow@redhat.com>
Acked-by: Anthony PERARD <anthony.perard@citrix.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Modify the pre_save method on VMStateDescription to return an int
rather than void so that it potentially can fail.
Changed zillions of devices to make them return 0; the only
case I've made it return non-0 is hw/intc/s390_flic_kvm.c that already
had an error_report/return case.
Note: If you add an error exit in your pre_save you must emit
an error_report to say why.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20170925112917.21340-2-dgilbert@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
SunOS defines SEC in <sys/time.h> as 1 (commonly used time symbols).
This fixes build on SmartOS (Joyent).
Patch cherry-picked from pkgsrc by jperkin (Joyent).
Signed-off-by: Kamil Rytarowski <n54@gmx.com>
Reviewed-by: Dmitry Fleytman <dmitry@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Disable debug output by default, the information were not needed for
release.
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Stefan Hajnoczi <stefanha@gmail.com>
Cc: Leonid Bloch <leonid.bloch@ravellosystems.com>
Cc: Dmitry Fleytman <dmitry.fleytman@ravellosystems.com>
Cc: qemu-stable@nongnu.org
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Jason Wang <jasowang@redhat.com>
This is a mostly-mechanical conversion that creates a new flat
union 'Netdev' QAPI type that covers all the branches of the
former 'NetClientOptions' simple union, where the branches are
now listed in a new 'NetClientDriver' enum rather than generated
from the simple union. The existence of a flat union has no
change to the command line syntax accepted for new code, and
will make it possible for a future patch to switch the QMP
command to parse a boxed union for no change to valid QMP; but
it does have some ripple effect on the C code when dealing with
the new types.
While making the conversion, note that the 'NetLegacy' type
remains unchanged: it applies only to legacy command line options,
and will not be ported to QMP, so it should remain a wrapper
around a simple union; to avoid confusion, the type named
'NetClientOptions' is now gone, and we introduce 'NetLegacyOptions'
in its place. Then, in the C code, we convert from NetLegacy to
Netdev as soon as possible, so that the bulk of the net stack
only has to deal with one QAPI type, not two. Note that since
the old legacy code always rejected 'hubport', we can just omit
that branch from the new 'NetLegacyOptions' simple union.
Based on an idea originally by Zoltán Kővágó <DirtY.iCE.hu@gmail.com>:
Message-Id: <01a527fbf1a5de880091f98cf011616a78adeeee.1441627176.git.DirtY.iCE.hu@gmail.com>
although the sed script in that patch no longer applies due to
other changes in the tree since then, and I also did some manual
cleanups (such as fixing whitespace to keep checkpatch happy).
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <1468468228-27827-13-git-send-email-eblake@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
[Fixup from Eric squashed in]
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Don't use *_to_cpup() to do byte-swapped loads; instead use
ld*_p() which correctly handle misaligned accesses.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Acked-by: Jason Wang <jasowang@redhat.com>
Acked-by: Dmitry Fleytman <dmitry@daynix.com <mailto:dmitry@daynix.com>>
Message-id: 1466097446-981-6-git-send-email-peter.maydell@linaro.org
Since mit_delay can never be 0 this if statement is
superfluous.
Signed-off-by: Sameeh Jubran <sameeh@daynix.com>
Reviewed-by: Stefan Weil <sw@weilnetz.de>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Code that will be shared moved to a separate files.
Signed-off-by: Dmitry Fleytman <dmitry.fleytman@ravellosystems.com>
Signed-off-by: Leonid Bloch <leonid.bloch@ravellosystems.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
This reverts commit 9596ef7c7b.
This workaround in order to fix endless interrupts is no
longer needed because it was superseded by the previous patch
(e1000: Fixing interrupt pace).
Signed-off-by: Sameeh Jubran <sameeh@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
This patch introduces an upper bound for number of interrupts
per second. Without this bound an interrupt storm can occur as
it has been observed on Windows 10 when disabling the device.
According to the SPEC - Intel PCI/PCI-X Family of Gigabit
Ethernet Controllers Software Developer's Manual, section
13.4.18 - the Ethernet controller guarantees a maximum
observable interrupt rate of 7813 interrupts/sec. If there is
no upper bound this could lead to an interrupt storm by e1000
(when mit_delay < 500) causing interrupts to fire at a very high
pace.
Thus if mit_delay < 500 then the delay should be set to the
minimum delay possible which is 500. This can be calculated
easily as follows:
Interval = 10^9 / (7813 * 256) = 500.
Signed-off-by: Sameeh Jubran <sameeh@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
The start_xmit() and e1000_receive_iov() functions implement DMA transfers
iterating over a set of descriptors that the guest's e1000 driver
prepares:
- the TDLEN and RDLEN registers store the total size of the descriptor
area,
- while the TDH and RDH registers store the offset (in whole tx / rx
descriptors) into the area where the transfer is supposed to start.
Each time a descriptor is processed, the TDH and RDH register is bumped
(as appropriate for the transfer direction).
QEMU already contains logic to deal with bogus transfers submitted by the
guest:
- Normally, the transmit case wants to increase TDH from its initial value
to TDT. (TDT is allowed to be numerically smaller than the initial TDH
value; wrapping at or above TDLEN bytes to zero is normal.) The failsafe
that QEMU currently has here is a check against reaching the original
TDH value again -- a complete wraparound, which should never happen.
- In the receive case RDH is increased from its initial value until
"total_size" bytes have been received; preferably in a single step, or
in "s->rxbuf_size" byte steps, if the latter is smaller. However, null
RX descriptors are skipped without receiving data, while RDH is
incremented just the same. QEMU tries to prevent an infinite loop
(processing only null RX descriptors) by detecting whether RDH assumes
its original value during the loop. (Again, wrapping from RDLEN to 0 is
normal.)
What both directions miss is that the guest could program TDLEN and RDLEN
so low, and the initial TDH and RDH so high, that these registers will
immediately be truncated to zero, and then never reassume their initial
values in the loop -- a full wraparound will never occur.
The condition that expresses this is:
xdh_start >= s->mac_reg[XDLEN] / sizeof(desc)
i.e., TDH or RDH start out after the last whole rx or tx descriptor that
fits into the TDLEN or RDLEN sized area.
This condition could be checked before we enter the loops, but
pci_dma_read() / pci_dma_write() knows how to fill in buffers safely for
bogus DMA addresses, so we just extend the existing failsafes with the
above condition.
This is CVE-2016-1981.
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Petr Matousek <pmatouse@redhat.com>
Cc: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Cc: Prasad Pandit <ppandit@redhat.com>
Cc: Michael Roth <mdroth@linux.vnet.ibm.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: qemu-stable@nongnu.org
RHBZ: https://bugzilla.redhat.com/show_bug.cgi?id=1296044
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1453832250-766-19-git-send-email-peter.maydell@linaro.org
Version: GnuPG v1
iQEcBAABAgAGBQJWZZJPAAoJEO8Ells5jWIRmp0H/26aFXVEgZykkUVNbqq05r7w
AI7podQlFOAESJHqZtR8FMaH8TAZ5GhphP4pn0PsWp54VjwcYZbdoME+dhZ4Elyc
WDanRHIweLv/zVg6+M8oHhw5GMaxtFLoLWrf0oanbUW9IZZmmM3COz/Y31hSVrR2
EzEJi1VZZhpMj3ibeOJns4MrugYrne8MtOdvusE/Uw2rJBTiStnWw1eTk8RmkNcg
5un1mQZxFU2AcNzmWdmWJmjY0rCnR3HhtTdZOwjM6uZGIJ9hbsItGzqiGadBfozI
fUtIa2HZahioe0VIzoB0snXnAuhV1jA0Uy18i04dPvgQOmiVSRjQNE2/lwQflyE=
=Pad3
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/jasowang/tags/net-pull-request' into staging
# gpg: Signature made Mon 07 Dec 2015 14:06:07 GMT using RSA key ID 398D6211
# gpg: Good signature from "Jason Wang (Jason Wang on RedHat) <jasowang@redhat.com>"
# gpg: WARNING: This key is not certified with sufficiently trusted signatures!
# gpg: It is not certain that the signature belongs to the owner.
# Primary key fingerprint: 215D 46F4 8246 689E C77F 3562 EF04 965B 398D 6211
* remotes/jasowang/tags/net-pull-request:
lan9118: log and ignore access to invalid registers, rather than aborting
lan9118: fix emulation of MAC address loaded bit in E2P_CMD register
vmxnet3: silence warning
pcnet: fix rx buffer overflow(CVE-2015-7512)
net: pcnet: add check to validate receive data size(CVE-2015-7504)
e1000: fix hang of win2k12 shutdown with flood ping
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
e1000 driver in Win2k12 is really well rotten. It 100% hangs on shutdown
of UP VM under flood ping. The guest checks card state and reinjects
itself interrupt in a loop. This is fatal for UP machine.
There is no good way to fix this misbehavior but to kludge it. The
emulation has interrupt throttling register aka ITR which limits
interrupt rate and allows the guest to proceed this phase.
There is no problem with this kludge for Linux guests - it adjust the
value of it itself.
On the other hand according to the initial research in
commit e9845f0985
Author: Vincenzo Maffione <v.maffione@gmail.com>
Date: Fri Aug 2 18:30:52 2013 +0200
e1000: add interrupt mitigation support
...
Interrupt mitigation boosts performance when the guest suffers from
an high interrupt rate (i.e. receiving short UDP packets at high packet
rate). For some numerical results see the following link
http://info.iet.unipi.it/~luigi/papers/20130520-rizzo-vm.pdf
this should also boost performance a bit.
See https://bugzilla.redhat.com/show_bug.cgi?id=874406 for additional
details.
Signed-off-by: Denis V. Lunev <den@openvz.org>
CC: Vincenzo Maffione <v.maffione@gmail.com>
CC: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
This follows the previous patches, where support for migrating the
entire MAC registers' array, and some new MAC registers were introduced.
This patch introduces the e1000-specific boolean parameter
"extra_mac_registers", which is on by default. Setting it to off will
enable migration to older versions of QEMU, but will disable the read
and write access to the new registers, that were introduced since adding
the ability to migrate the entire MAC array.
Example for usage to enable backward compatibility and to disable the
new MAC registers:
qemu-system-x86_64 -device e1000,extra_mac_registers=off,... ...
As mentioned above, the default value is "on".
Signed-off-by: Leonid Bloch <leonid.bloch@ravellosystems.com>
Signed-off-by: Dmitry Fleytman <dmitry.fleytman@ravellosystems.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
This implements the following Statistic registers (various counters)
according to Intel's specs:
TSCTC GOTCL GOTCH GORCL GORCH MPRC BPRC RUC ROC
BPTC MPTC PTC... PRC...
PLEASE NOTE: these registers will not be active, nor will migrate, until
a compatibility flag will be set (in the next patch in this series).
Signed-off-by: Leonid Bloch <leonid.bloch@ravellosystems.com>
Signed-off-by: Dmitry Fleytman <dmitry.fleytman@ravellosystems.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Previously, if promiscuous unicast was enabled, a packet was received
straight away, even if it was a multicast or a broadcast packet. This
patch fixes that behavior, while making the filtering procedure a bit
more human-readable.
Signed-off-by: Leonid Bloch <leonid.bloch@ravellosystems.com>
Signed-off-by: Dmitry Fleytman <dmitry.fleytman@ravellosystems.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
