This patch implements initial support for Single Root I/O Virtualization
on an NVMe device.
Essentially, it allows to define the maximum number of virtual functions
supported by the NVMe controller via sriov_max_vfs parameter.
Passing a non-zero value to sriov_max_vfs triggers reporting of SR-IOV
capability by a physical controller and ARI capability by both the
physical and virtual function devices.
NVMe controllers created via virtual functions mirror functionally
the physical controller, which may not entirely be the case, thus
consideration would be needed on the way to limit the capabilities of
the VF.
NVMe subsystem is required for the use of SR-IOV.
Signed-off-by: Lukasz Maniak <lukasz.maniak@linux.intel.com>
Reviewed-by: Klaus Jensen <k.jensen@samsung.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
This is for code which needs a portable equivalent to a QIOChannelFile
connected to /dev/null.
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Add support for writing and reading the device address register in old
register mode.
On the AST2400 (only 1 slave address)
* no upper bits
On the AST2500 (2 possible slave addresses),
* bit[31] : Slave Address match indicator
* bit[30] : Slave Address Receiving pending
On the AST2600 (3 possible slave addresses),
* bit[31-30] : Slave Address match indicator
* bit[29] : Slave Address Receiving pending
The model could be more precise to take into account all fields but
since the Linux driver is masking the register value being set, it
should be fine. See commit 3fb2e2aeafb2 ("i2c: aspeed: disable
additional device addresses on ast2[56]xx") from Zeiv. This can be
addressed later.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
[ clg: add details to commit log ]
Message-Id: <20220601210831.67259-3-its@irrelevant.dk>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Moves register definitions and short commonly used inlined functiosn to
the header file to help tidy up the implementation file.
Signed-off-by: Joe Komlodi <komlodi@google.com>
Change-Id: I34dff7485b6bbe3c9482715ccd94dbd65dc5f324
Message-Id: <20220331043248.2237838-8-komlodi@google.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
On AST2600, I2C has a secondary mode, called "new mode", which changes
the layout of registers, adds some minor behavior changes, and
introduces a new way to transfer data called "packet mode".
Most of the bit positions of the fields are the same between old and new
mode, so we use SHARED_FIELD_XX macros to reuse most of the code between
the different modes.
For packet mode, most of the command behavior is the same compared to
other modes, but there are some minor changes to how interrupts are
handled compared to other modes.
Signed-off-by: Joe Komlodi <komlodi@google.com>
Change-Id: I072f8301964f623afc74af1fe50c12e5caef199e
Message-Id: <20220331043248.2237838-6-komlodi@google.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Using a register array will allow us to represent old-mode and new-mode
I2C registers by using the same underlying register array, instead of
adding an entire new set of variables to represent new mode.
As part of this, we also do additional cleanup to use ARRAY_FIELD_
macros instead of FIELD_ macros on registers.
Signed-off-by: Joe Komlodi <komlodi@google.com>
Change-Id: Ib94996b17c361b8490c042b43c99d8abc69332e3
[ clg: use of memset in aspeed_i2c_bus_reset() ]
Message-Id: <20220331043248.2237838-5-komlodi@google.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Occasionally a peripheral will have different operating modes, where the
MMIO layout changes, but some of the register fields have the same offsets
and behaviors.
To help support this, we add SHARED_FIELD_XX macros that create SHIFT,
LENGTH, and MASK macros for the fields that are shared across registers,
and accessors for these fields.
An example use may look as follows:
There is a peripheral with registers REG_MODE1 and REG_MODE2 at
different addreses, and both have a field FIELD1 initialized by
SHARED_FIELD().
Depending on what mode the peripheral is operating in, the user could
extract FIELD1 via
SHARED_ARRAY_FIELD_EX32(s->regs, R_REG_MODE1, FIELD1)
or
SHARED_ARRAY_FIELD_EX32(s->regs, R_REG_MODE2, FIELD1)
Signed-off-by: Joe Komlodi <komlodi@google.com>
Change-Id: Id3dc53e7d2f8741c95697cbae69a81bb699fa3cb
Message-Id: <20220331043248.2237838-2-komlodi@google.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Based on already existing QEMU implementation created a signed
256 bit by 128 bit division needed to implement the vector divide
extended signed quadword instruction from PowerISA 3.1
Signed-off-by: Lucas Mateus Castro (alqotel) <lucas.araujo@eldorado.org.br>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20220525134954.85056-6-lucas.araujo@eldorado.org.br>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Based on already existing QEMU implementation, created an unsigned 256
bit by 128 bit division needed to implement the vector divide extended
unsigned instruction from PowerISA3.1
Signed-off-by: Lucas Mateus Castro (alqotel) <lucas.araujo@eldorado.org.br>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20220525134954.85056-5-lucas.araujo@eldorado.org.br>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
There are two parts in this patch:
1, support akcipher service by cryptodev-builtin driver
2, virtio-crypto driver supports akcipher service
In principle, we should separate this into two patches, to avoid
compiling error, merge them into one.
Then virtio-crypto gets request from guest side, and forwards the
request to builtin driver to handle it.
Test with a guest linux:
1, The self-test framework of crypto layer works fine in guest kernel
2, Test with Linux guest(with asym support), the following script
test(note that pkey_XXX is supported only in a newer version of keyutils):
- both public key & private key
- create/close session
- encrypt/decrypt/sign/verify basic driver operation
- also test with kernel crypto layer(pkey add/query)
All the cases work fine.
Run script in guest:
rm -rf *.der *.pem *.pfx
modprobe pkcs8_key_parser # if CONFIG_PKCS8_PRIVATE_KEY_PARSER=m
rm -rf /tmp/data
dd if=/dev/random of=/tmp/data count=1 bs=20
openssl req -nodes -x509 -newkey rsa:2048 -keyout key.pem -out cert.pem -subj "/C=CN/ST=BJ/L=HD/O=qemu/OU=dev/CN=qemu/emailAddress=qemu@qemu.org"
openssl pkcs8 -in key.pem -topk8 -nocrypt -outform DER -out key.der
openssl x509 -in cert.pem -inform PEM -outform DER -out cert.der
PRIV_KEY_ID=`cat key.der | keyctl padd asymmetric test_priv_key @s`
echo "priv key id = "$PRIV_KEY_ID
PUB_KEY_ID=`cat cert.der | keyctl padd asymmetric test_pub_key @s`
echo "pub key id = "$PUB_KEY_ID
keyctl pkey_query $PRIV_KEY_ID 0
keyctl pkey_query $PUB_KEY_ID 0
echo "Enc with priv key..."
keyctl pkey_encrypt $PRIV_KEY_ID 0 /tmp/data enc=pkcs1 >/tmp/enc.priv
echo "Dec with pub key..."
keyctl pkey_decrypt $PRIV_KEY_ID 0 /tmp/enc.priv enc=pkcs1 >/tmp/dec
cmp /tmp/data /tmp/dec
echo "Sign with priv key..."
keyctl pkey_sign $PRIV_KEY_ID 0 /tmp/data enc=pkcs1 hash=sha1 > /tmp/sig
echo "Verify with pub key..."
keyctl pkey_verify $PRIV_KEY_ID 0 /tmp/data /tmp/sig enc=pkcs1 hash=sha1
echo "Enc with pub key..."
keyctl pkey_encrypt $PUB_KEY_ID 0 /tmp/data enc=pkcs1 >/tmp/enc.pub
echo "Dec with priv key..."
keyctl pkey_decrypt $PRIV_KEY_ID 0 /tmp/enc.pub enc=pkcs1 >/tmp/dec
cmp /tmp/data /tmp/dec
echo "Verify with pub key..."
keyctl pkey_verify $PUB_KEY_ID 0 /tmp/data /tmp/sig enc=pkcs1 hash=sha1
Reviewed-by: Gonglei <arei.gonglei@huawei.com>
Signed-off-by: lei he <helei.sig11@bytedance.com
Signed-off-by: zhenwei pi <pizhenwei@bytedance.com>
Message-Id: <20220611064243.24535-2-pizhenwei@bytedance.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
When switching address space with mutex lock hold, mapping will be
replayed for assigned device. This will trigger relock deadlock.
Also release the mutex resource in unrealize routine.
Signed-off-by: Zhenzhong Duan <zhenzhong.duan@intel.com>
Message-Id: <20220613061010.2674054-3-zhenzhong.duan@intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Currently assigned devices can not work in virtio-iommu bypass mode.
Guest driver fails to probe the device due to DMA failure. And the
reason is because of lacking GPA -> HPA mappings when VM is created.
Add a root container memory region to hold both bypass memory region
and iommu memory region, so the switch between them is supported
just like the implementation in virtual VT-d.
Signed-off-by: Zhenzhong Duan <zhenzhong.duan@intel.com>
Message-Id: <20220613061010.2674054-2-zhenzhong.duan@intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
An initial simple upstream port emulation to allow the creation
of CXL switches. The Device ID has been allocated for this use.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20220616145126.8002-2-Jonathan.Cameron@huawei.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
* virtio reset cleanups
* build system cleanups
* fix Cirrus CI
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEE8TM4V0tmI4mGbHaCv/vSX3jHroMFAmKpooQUHHBib256aW5p
QHJlZGhhdC5jb20ACgkQv/vSX3jHroNlFwf+OugLGRZl3KVc7akQwUJe9gg2T31h
VkC+7Tei8FAwe8vDppVd+CYEIi0M3acxD2amRrv2etCCGSuySN1PbkfRcSfPBX01
pRWpasdhfqnZR8Iidi7YW1Ou5CcGqKH49nunBhW10+osb/mu5sVscMuOJgTDj/lK
CpsmDyk6572yGmczjNLlmhYcTU36clHpAZgazZHwk1PU+B3fCKlYYyvUpT3ItJvd
cK92aIUWrfofl3yTy0k4IwvZwNjTBirlstOIomZ333xzSA+mm5TR+mTvGRTZ69+a
v+snpMp4ILDMoB5kxQ42kK5WpdiN//LnriA9CBFDtOidsDDn8kx7gJe2RA==
=Dxwa
-----END PGP SIGNATURE-----
Merge tag 'for-upstream' of https://gitlab.com/bonzini/qemu into staging
* statistics subsystem
* virtio reset cleanups
* build system cleanups
* fix Cirrus CI
# -----BEGIN PGP SIGNATURE-----
#
# iQFIBAABCAAyFiEE8TM4V0tmI4mGbHaCv/vSX3jHroMFAmKpooQUHHBib256aW5p
# QHJlZGhhdC5jb20ACgkQv/vSX3jHroNlFwf+OugLGRZl3KVc7akQwUJe9gg2T31h
# VkC+7Tei8FAwe8vDppVd+CYEIi0M3acxD2amRrv2etCCGSuySN1PbkfRcSfPBX01
# pRWpasdhfqnZR8Iidi7YW1Ou5CcGqKH49nunBhW10+osb/mu5sVscMuOJgTDj/lK
# CpsmDyk6572yGmczjNLlmhYcTU36clHpAZgazZHwk1PU+B3fCKlYYyvUpT3ItJvd
# cK92aIUWrfofl3yTy0k4IwvZwNjTBirlstOIomZ333xzSA+mm5TR+mTvGRTZ69+a
# v+snpMp4ILDMoB5kxQ42kK5WpdiN//LnriA9CBFDtOidsDDn8kx7gJe2RA==
# =Dxwa
# -----END PGP SIGNATURE-----
# gpg: Signature made Wed 15 Jun 2022 02:12:36 AM PDT
# gpg: using RSA key F13338574B662389866C7682BFFBD25F78C7AE83
# gpg: issuer "pbonzini@redhat.com"
# gpg: Good signature from "Paolo Bonzini <bonzini@gnu.org>" [undefined]
# gpg: aka "Paolo Bonzini <pbonzini@redhat.com>" [undefined]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 46F5 9FBD 57D6 12E7 BFD4 E2F7 7E15 100C CD36 69B1
# Subkey fingerprint: F133 3857 4B66 2389 866C 7682 BFFB D25F 78C7 AE83
* tag 'for-upstream' of https://gitlab.com/bonzini/qemu: (21 commits)
build: include pc-bios/ part in the ROMS variable
meson: put cross compiler info in a separate section
q35：Enable TSEG only when G_SMRAME and TSEG_EN both enabled
build: fix check for -fsanitize-coverage-allowlist
tests/vm: allow running tests in an unconfigured source tree
configure: cleanup -fno-pie detection
configure: update list of preserved environment variables
virtio-mmio: cleanup reset
virtio: stop ioeventfd on reset
virtio-mmio: stop ioeventfd on legacy reset
s390x: simplify virtio_ccw_reset_virtio
block: add more commands to preconfig mode
hmp: add filtering of statistics by name
qmp: add filtering of statistics by name
hmp: add filtering of statistics by provider
qmp: add filtering of statistics by provider
hmp: add basic "info stats" implementation
cutils: add functions for IEC and SI prefixes
qmp: add filtering of statistics by target vCPU
kvm: Support for querying fd-based stats
...
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Forward remote device's interrupts to the guest
Signed-off-by: Elena Ufimtseva <elena.ufimtseva@oracle.com>
Signed-off-by: John G Johnson <john.g.johnson@oracle.com>
Signed-off-by: Jagannathan Raman <jag.raman@oracle.com>
Message-id: 9523479eaafe050677f4de2af5dd0df18c27cfd9.1655151679.git.jag.raman@oracle.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Determine the BARs used by the PCI device and register handlers to
manage the access to the same.
Signed-off-by: Elena Ufimtseva <elena.ufimtseva@oracle.com>
Signed-off-by: John G Johnson <john.g.johnson@oracle.com>
Signed-off-by: Jagannathan Raman <jag.raman@oracle.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 3373e10b5be5f42846f0632d4382466e1698c505.1655151679.git.jag.raman@oracle.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Assign separate address space for each device in the remote processes.
Signed-off-by: Elena Ufimtseva <elena.ufimtseva@oracle.com>
Signed-off-by: John G Johnson <john.g.johnson@oracle.com>
Signed-off-by: Jagannathan Raman <jag.raman@oracle.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: afe0b0a97582cdad42b5b25636a29c523265a10a.1655151679.git.jag.raman@oracle.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Define vfio-user object which is remote process server for QEMU. Setup
object initialization functions and properties necessary to instantiate
the object
Signed-off-by: Elena Ufimtseva <elena.ufimtseva@oracle.com>
Signed-off-by: John G Johnson <john.g.johnson@oracle.com>
Signed-off-by: Jagannathan Raman <jag.raman@oracle.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: e45a17001e9b38f451543a664ababdf860e5f2f2.1655151679.git.jag.raman@oracle.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Add vfio-user to x-remote machine. It is a boolean, which indicates if
the machine supports vfio-user protocol. The machine configures the bus
differently vfio-user and multiprocess protocols, so this property
informs it on how to configure the bus.
This property should be short lived. Once vfio-user fully replaces
multiprocess, this property could be removed.
Signed-off-by: Elena Ufimtseva <elena.ufimtseva@oracle.com>
Signed-off-by: John G Johnson <john.g.johnson@oracle.com>
Signed-off-by: Jagannathan Raman <jag.raman@oracle.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 5d51a152a419cbda35d070b8e49b772b60a7230a.1655151679.git.jag.raman@oracle.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Add blocker to prevent hot-unplug of devices
TYPE_VFIO_USER_SERVER, which is introduced shortly, attaches itself to a
PCIDevice on which it depends. If the attached PCIDevice gets removed
while the server in use, it could cause it crash. To prevent this,
TYPE_VFIO_USER_SERVER adds an unplug blocker for the PCIDevice.
Signed-off-by: Elena Ufimtseva <elena.ufimtseva@oracle.com>
Signed-off-by: John G Johnson <john.g.johnson@oracle.com>
Signed-off-by: Jagannathan Raman <jag.raman@oracle.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: c41ef80b7cc063314d629737bed2159e5713f2e0.1655151679.git.jag.raman@oracle.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Allow retrieving only a subset of statistics. This can be useful
for example in order to plot a subset of the statistics many times
a second: KVM publishes ~40 statistics for each vCPU on x86; retrieving
and serializing all of them would be useless.
Another use will be in HMP in the following patch; implementing the
filter in the backend is easy enough that it was deemed okay to make
this a public interface.
Example:
{ "execute": "query-stats",
"arguments": {
"target": "vcpu",
"vcpus": [ "/machine/unattached/device[2]",
"/machine/unattached/device[4]" ],
"providers": [
{ "provider": "kvm",
"names": [ "l1d_flush", "exits" ] } } }
{ "return": {
"vcpus": [
{ "path": "/machine/unattached/device[2]"
"providers": [
{ "provider": "kvm",
"stats": [ { "name": "l1d_flush", "value": 41213 },
{ "name": "exits", "value": 74291 } ] } ] },
{ "path": "/machine/unattached/device[4]"
"providers": [
{ "provider": "kvm",
"stats": [ { "name": "l1d_flush", "value": 16132 },
{ "name": "exits", "value": 57922 } ] } ] } ] } }
Extracted from a patch by Mark Kanda.
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Allow retrieving the statistics from a specific provider only.
This can be used in the future by HMP commands such as "info
sync-profile" or "info profile". The next patch also adds
filter-by-provider capabilities to the HMP equivalent of
query-stats, "info stats".
Example:
{ "execute": "query-stats",
"arguments": {
"target": "vm",
"providers": [
{ "provider": "kvm" } ] } }
The QAPI is a bit more verbose than just a list of StatsProvider,
so that it can be subsequently extended with filtering of statistics
by name.
If a provider is specified more than once in the filter, each request
will be included separately in the output.
Extracted from a patch by Mark Kanda.
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add an HMP command to retrieve statistics collected at run-time.
The command will retrieve and print either all VM-level statistics,
or all vCPU-level statistics for the currently selected CPU.
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Extract the knowledge of IEC and SI prefixes out of size_to_str and
freq_to_str, so that it can be reused when printing statistics.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Introduce a simple filtering of statistics, that allows to retrieve
statistics for a subset of the guest vCPUs. This will be used for
example by the HMP monitor, in order to retrieve the statistics
for the currently selected CPU.
Example:
{ "execute": "query-stats",
"arguments": {
"target": "vcpu",
"vcpus": [ "/machine/unattached/device[2]",
"/machine/unattached/device[4]" ] } }
Extracted from a patch by Mark Kanda.
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Gathering statistics is important for development, for monitoring and
for performance measurement. There are tools such as kvm_stat that do
this and they rely on the _user_ knowing the interesting data points
rather than the tool (which can treat them as opaque).
The commands introduced in this commit introduce QMP support for
querying stats; the goal is to take the capabilities of these tools
and making them available throughout the whole virtualization stack,
so that one can observe, monitor and measure virtual machines without
having shell access + root on the host that runs them.
query-stats returns a list of all stats per target type (only VM
and vCPU to start); future commits add extra options for specifying
stat names, vCPU qom paths, and providers. All these are used by the
HMP command "info stats". Because of the development usecases around
statistics, a good HMP interface is important.
query-stats-schemas returns a list of stats included in each target
type, with an option for specifying the provider. The concepts in the
schema are based on the KVM binary stats' own introspection data, just
translated to QAPI.
There are two reasons to have a separate schema that is not tied to
the QAPI schema. The first is the contents of the schemas: the new
introspection data provides different information than the QAPI data,
namely unit of measurement, how the numbers are gathered and change
(peak/instant/cumulative/histogram), and histogram bucket sizes.
There's really no reason to have this kind of metadata in the QAPI
introspection schema (except possibly for the unit of measure, but
there's a very weak justification).
Another reason is the dynamicity of the schema. The QAPI introspection
data is very much static; and while QOM is somewhat more dynamic,
generally we consider that to be a bug rather than a feature these days.
On the other hand, the statistics that are exposed by QEMU might be
passed through from another source, such as KVM, and the disadvantages of
manually updating the QAPI schema for outweight the benefits from vetting
the statistics and filtering out anything that seems "too unstable".
Running old QEMU with new kernel is a supported usecase; if old QEMU
cannot expose statistics from a new kernel, or if a kernel developer
needs to change QEMU before gathering new info from the new kernel,
then that is a poor user interface.
The framework provides a method to register callbacks for these QMP
commands. Most of the work in fact is done by the callbacks, and a
large majority of this patch is new QAPI structs and commands.
Examples (with KVM stats):
- Query all VM stats:
{ "execute": "query-stats", "arguments" : { "target": "vm" } }
{ "return": [
{ "provider": "kvm",
"stats": [
{ "name": "max_mmu_page_hash_collisions", "value": 0 },
{ "name": "max_mmu_rmap_size", "value": 0 },
{ "name": "nx_lpage_splits", "value": 148 },
... ] },
{ "provider": "xyz",
"stats": [ ... ] }
] }
- Query all vCPU stats:
{ "execute": "query-stats", "arguments" : { "target": "vcpu" } }
{ "return": [
{ "provider": "kvm",
"qom_path": "/machine/unattached/device[0]"
"stats": [
{ "name": "guest_mode", "value": 0 },
{ "name": "directed_yield_successful", "value": 0 },
{ "name": "directed_yield_attempted", "value": 106 },
... ] },
{ "provider": "kvm",
"qom_path": "/machine/unattached/device[1]"
"stats": [
{ "name": "guest_mode", "value": 0 },
{ "name": "directed_yield_successful", "value": 0 },
{ "name": "directed_yield_attempted", "value": 106 },
... ] },
] }
- Retrieve the schemas:
{ "execute": "query-stats-schemas" }
{ "return": [
{ "provider": "kvm",
"target": "vcpu",
"stats": [
{ "name": "guest_mode",
"unit": "none",
"base": 10,
"exponent": 0,
"type": "instant" },
{ "name": "directed_yield_successful",
"unit": "none",
"base": 10,
"exponent": 0,
"type": "cumulative" },
... ]
},
{ "provider": "kvm",
"target": "vm",
"stats": [
{ "name": "max_mmu_page_hash_collisions",
"unit": "none",
"base": 10,
"exponent": 0,
"type": "peak" },
... ]
},
{ "provider": "xyz",
"target": "vm",
"stats": [ ... ]
}
] }
Signed-off-by: Mark Kanda <mark.kanda@oracle.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This change adds a new member, refresh_rate to QemuUIInfo in
include/ui/console.h. It represents the refresh rate of the
physical display backend, and it is more appropriate than
GUI update interval as the refresh rate which the emulated device
reports:
- sdl may set GUI update interval shorter than the refresh rate
of the physical display to respond to user-generated events.
- sdl and vnc aggressively changes GUI update interval, but
a guests is typically not designed to respond to frequent
refresh rate changes, or frequent "display mode" changes in
general. The frequency of refresh rate changes of the physical
display backend matches better to the guest's expectation.
QemuUIInfo also has other members representing "display mode",
which makes it suitable for refresh rate representation. It has
a throttling of update notifications, and prevents frequent changes
of the display mode.
Signed-off-by: Akihiko Odaki <akihiko.odaki@gmail.com>
Message-Id: <20220226115516.59830-3-akihiko.odaki@gmail.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The returned value is not used and misleading.
Signed-off-by: Akihiko Odaki <akihiko.odaki@gmail.com>
Message-Id: <20220226115516.59830-2-akihiko.odaki@gmail.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
dump_opcount_info() is a one-line wrapper around tcg_dump_op_count()
which is also exported. So use the latter directly.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20220520180109.8224-10-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Commit 3a841ab53f 'qapi: introduce
x-query-jit QMP command' basically moved the only function using
dump_drift_info() to cpu-exec.c. Therefore, dump_drift_info() doesn't
need to be exported any longer.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20220520180109.8224-9-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20220520180109.8224-6-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20220520180109.8224-5-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
The macro seems to be used only internally, so remove it.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20220520180109.8224-4-shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Exposing the io_base offset as a QOM property not only allows it to be
configurable but also to be displayed in HMP:
Before:
(qemu) info qtree
...
dev: mc146818rtc, id ""
gpio-out "" 1
base_year = 0 (0x0)
irq = 8 (0x8)
lost_tick_policy = "discard"
After:
dev: mc146818rtc, id ""
gpio-out "" 1
base_year = 0 (0x0)
iobase = 112 (0x70)
irq = 8 (0x8)
lost_tick_policy = "discard"
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20220529184006.10712-4-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
During the previous changesets piix3_create() became a trivial
wrapper around more generic functions. Modernize the code.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20220603185045.143789-12-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Modernizes the code.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20220603185045.143789-11-shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
During the previous changesets piix4_create() became a trivial
wrapper around more generic functions. Modernize the code.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20220603185045.143789-8-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Just like the real hardware, create the PIIX4 ACPI controller as part of
the PIIX4 southbridge. This also mirrors how the IDE and USB functions
are already created.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20220603185045.143789-7-shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Modernizes the code.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20220603185045.143789-6-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
TYPE_PIIX3_PCI_DEVICE resides there as already, so add the remaining
ones, too.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20220603185045.143789-2-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
This function is now unused and so can be completely removed.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20220528091934.15520-13-mark.cave-ayland@ilande.co.uk>
Reviewed-by: Bernhard Beschow <shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Initialize the SMI IRQ in piix4_pm_init().
The smi_irq can now be wired up directly using a qdev gpio instead
of having to set the IRQ externally in piix4_pm_initfn().
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20220528091934.15520-10-mark.cave-ayland@ilande.co.uk>
[PMD: Partially squash 20220528091934.15520-8-mark.cave-ayland@ilande.co.uk]
Reviewed-by: Bernhard Beschow <shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Introduce piix4_pm_init() instance init function and use it to
initialise the separate qdev gpio for the SCI IRQ.
The sci_irq can now be wired up directly using a qdev gpio instead
of having to set the IRQ externally in piix4_pm_initfn().
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20220528091934.15520-9-mark.cave-ayland@ilande.co.uk>
[PMD: Partially squash 20220528091934.15520-8-mark.cave-ayland@ilande.co.uk]
Reviewed-by: Bernhard Beschow <shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
When QOMifying a device it is typical to use _init() as the suffix for an
instance_init function, however this name is already in use by the legacy
piix4_pm_init() wrapper function. Eventually the wrapper function will be
removed, but for now rename it to piix4_pm_initfn() to avoid a naming
collision.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20220528091934.15520-7-mark.cave-ayland@ilande.co.uk>
Reviewed-by: Bernhard Beschow <shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
This exposes the PIIX4_PM device to the caller to allow any qdev gpios to be
mapped outside of piix4_pm_init().
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20220528091934.15520-6-mark.cave-ayland@ilande.co.uk>
Reviewed-by: Bernhard Beschow <shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
This allows the QOM types in hw/acpi/piix4.c to be used elsewhere by simply including
hw/acpi/piix4.h.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20220528091934.15520-5-mark.cave-ayland@ilande.co.uk>
Reviewed-by: Bernhard Beschow <shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
This is in preparation for conversion to a qdev property.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Ani Sinha <ani@anisinha.ca>
Message-Id: <20220528091934.15520-3-mark.cave-ayland@ilande.co.uk>
[PMD: Change simm_enabled from int to bool, suggested by Ani Sinha]
Reviewed-by: Bernhard Beschow <shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
The sysbus floppy controllers (devices sysbus-fdc and sun-fdtwo)
don't support DMA. The core floppy controller code expects this to
be indicated by setting FDCtrl::dma_chann to -1. This used to be
done in the device instance_init functions sysbus_fdc_initfn() and
sun4m_fdc_initfn(), but in commit 1430759ec3 we refactored this code
and accidentally lost the setting of dma_chann.
For sysbus-fdc this has no ill effects because we were redundantly
also setting dma_chann in fdctrl_init_sysbus(), but for sun-fdtwo
this means that guests which try to enable DMA on the floppy
controller will cause QEMU to crash because FDCtrl::dma is NULL.
Set dma_chann to -1 in the common instance init, and remove the
redundant code in fdctrl_init_sysbus() that is also setting it.
There is a six-year-old FIXME comment in the jazz board code to the
effect that in theory it should support doing DMA via a custom DMA
controller. If anybody ever chooses to fix that they can do it by
adding support for setting both FDCtrl::dma_chann and FDCtrl::dma.
(A QOM link property 'dma-controller' on the sysbus device which can
be set to an instance of IsaDmaClass is probably the way to go.)
Fixes: 1430759ec3 ("hw/block/fdc: Extract SysBus floppy controllers to fdc-sysbus.c")
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/958
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20220505101842.2757905-1-peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
more CXL patches
VIOT
Igor's huge AML rework
fixes, cleanups all over the place
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAmKj4YcPHG1zdEByZWRo
YXQuY29tAAoJECgfDbjSjVRpkNcIAKTsMfUVueTjelC2RwIdegQkypycKhCweKzc
QxddaEr0w+N2164byT3IUy9h53hV3qAAmMuGE4d8B2r5rykf+SwDfIeNmHNqntnA
oLraXIxSSAf4/1cTsRCVL/BXo2E9P+WHI3huw37HClmPLdyMjQa1AtpTpKnIsbmO
sBZf7t5yHDJ2WGZwBQ1IbAxvsdGo1fa1TCt1jZ9g1dmnQSTteQG8DHkGoRnkwTi7
510jb0e8uQEgKytCdLTHqESHlfgjvoI73OFOAR2dzTKy6KelFmdLYSo2FtsIdtT5
1fZNaDjtl6zQ4b2iLBgPpHtikKch9BzzhDMbCsq7FpvasZ8u2FE=
=LXG0
-----END PGP SIGNATURE-----
Merge tag 'for_upstream' of git://git.kernel.org/pub/scm/virt/kvm/mst/qemu into staging
virtio,pc,pci: fixes,cleanups,features
more CXL patches
VIOT
Igor's huge AML rework
fixes, cleanups all over the place
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# -----BEGIN PGP SIGNATURE-----
#
# iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAmKj4YcPHG1zdEByZWRo
# YXQuY29tAAoJECgfDbjSjVRpkNcIAKTsMfUVueTjelC2RwIdegQkypycKhCweKzc
# QxddaEr0w+N2164byT3IUy9h53hV3qAAmMuGE4d8B2r5rykf+SwDfIeNmHNqntnA
# oLraXIxSSAf4/1cTsRCVL/BXo2E9P+WHI3huw37HClmPLdyMjQa1AtpTpKnIsbmO
# sBZf7t5yHDJ2WGZwBQ1IbAxvsdGo1fa1TCt1jZ9g1dmnQSTteQG8DHkGoRnkwTi7
# 510jb0e8uQEgKytCdLTHqESHlfgjvoI73OFOAR2dzTKy6KelFmdLYSo2FtsIdtT5
# 1fZNaDjtl6zQ4b2iLBgPpHtikKch9BzzhDMbCsq7FpvasZ8u2FE=
# =LXG0
# -----END PGP SIGNATURE-----
# gpg: Signature made Fri 10 Jun 2022 05:27:51 PM PDT
# gpg: using RSA key 5D09FD0871C8F85B94CA8A0D281F0DB8D28D5469
# gpg: issuer "mst@redhat.com"
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>" [undefined]
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>" [undefined]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* tag 'for_upstream' of git://git.kernel.org/pub/scm/virt/kvm/mst/qemu: (53 commits)
hw/vhost-user-scsi|blk: set `supports_config` flag correctly
hw/virtio/vhost-user: don't use uninitialized variable
tests/acpi: virt: update golden masters for VIOT
hw/acpi/viot: sort VIOT ACPI table entries by PCI host bridge min_bus
tests/acpi: virt: allow VIOT acpi table changes
hw/acpi/viot: build array of PCI host bridges before generating VIOT ACPI table
hw/acpi/viot: move the individual PCI host bridge entry generation to a new function
hw/acpi/viot: rename build_pci_range_node() to enumerate_pci_host_bridges()
hw/cxl: Fix missing write mask for HDM decoder target list registers
pci: fix overflow in snprintf string formatting
hw/machine: Drop cxl_supported flag as no longer useful
hw/cxl: Move the CXLState from MachineState to machine type specific state.
tests/acpi: Update q35/CEDT.cxl for new memory addresses.
pci/pci_expander_bridge: For CXL HB delay the HB register memory region setup.
tests/acpi: Allow modification of q35 CXL CEDT table.
hw/cxl: Push linking of CXL targets into i386/pc rather than in machine.c
hw/acpi/cxl: Pass in the CXLState directly rather than MachineState
hw/cxl: Make the CXL fixed memory window setup a machine parameter.
x86: acpi-build: do not include hw/isa/isa.h directly
tests: acpi: update expected DSDT.tis.tpm2/DSDT.tis.tpm12 blobs
...
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
As all the CXL elements have moved to boards that support
CXL, there is no need to maintain a top level flag.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Message-Id: <20220608145440.26106-9-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This removes the last of the CXL code from the MachineState where it
is visible to all Machines to only those that support CXL (currently i386/pc)
As i386/pc always support CXL now, stop allocating the state independently.
Note the pxb register hookup code runs even if cxl=off in order to detect
pxb_cxl host bridges and fail to start if any are present as they won't
have the control registers available.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Message-Id: <20220608145440.26106-8-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
As the CXLState will no long be accessible via MachineState
at time of PXB_CXL realization, come back later from the machine specific
code to fill in the missing memory region setup. Only at this stage
is it possible to check if cxl=on, so that check is moved to this
later point.
Note that for multiple host bridges, the allocation order of the
register spaces is changed. This will be reflected in ACPI CEDT.
Stubs are added to handle case of CONFIG_PXB=n for machines that
call these functions.
The bus walking logic is common to all machines so add a utility
function + stub to cxl-host*.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Message-Id: <20220608145440.26106-6-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Whilst here take the oportunity to shorten the function name.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Message-Id: <20220608145440.26106-4-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Refactoring step on path to moving all CXL state out of
MachineState.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Message-Id: <20220608145440.26106-3-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Paolo Bonzini requested this change to simplify the ongoing
effort to allow machine setup entirely via RPC.
Includes shortening the command line form cxl-fixed-memory-window
to cxl-fmw as the command lines are extremely long even with this
change.
The json change is needed to ensure that there is
a CXLFixedMemoryWindowOptionsList even though the actual
element in the json is never used. Similar to existing
SgxEpcProperties.
Update qemu-options.hx to reflect that this is now a -machine
parameter. The bulk of -M / -machine parameters are documented
under machine, so use that in preference to M.
Update cxl-test and bios-tables-test to reflect new parameters.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Davidlohr Bueso <dave@stgolabs.net>
Message-Id: <20220608145440.26106-2-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
.. and clean up not longer needed conditionals in DSTD build code
pvpanic-isa AML will be fetched and included when ISA bridge will
build its own AML code (including attached devices).
Expected AML change:
the device under separate _SB.PCI0.ISA scope is moved directly
under Device(ISA) node.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Message-Id: <20220608135340.3304695-29-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
.. and clean up not longer needed conditionals in DSTD build
code. applesmc AML will be fetched and included when ISA bridge
will build its own AML code (incl. attached devices).
Expected AML change:
the device under separate _SB.PCI0.ISA scope is moved directly
under Device(ISA) node.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Message-Id: <20220608135340.3304695-25-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
by default we do not version ACPI AML as it's considered
a part of firmware. Drop do_not_add_smb_acpi that blocked
SMBUS AML description on 3.1 and older machine types without
providing justification.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Message-Id: <20220608135340.3304695-18-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
convert ad-hoc way we use to generate AML for ISA/SMB IPMI devices
to a generic approach (i.e. make devices provide its own AML blobs
like it is done with other ISA devices (ex. KBD))
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Message-Id: <20220608135340.3304695-17-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
smbus-ipmi AML description needs to specify a path to its parent
node in _CRS. The rest of IPMI inplementations (ISA based)
do not need path at all. Instead of passing through a full path
use relative path to point to smbus-ipmi's parent node, it will
let follow up patches to create IPMI device AML in a generic
way instead of current ad-hoc way. (i.e. AML will be generated
the same way it's done for other ISA device, and smbus will be
converted to generate AML for its slave devices the same way
as ISA)
expected AML change:
Name (_CRS, ResourceTemplate () // _CRS: Current Resource Settings
{
I2cSerialBusV2 (0x0000, ControllerInitiated, 0x000186A0,
- AddressingMode7Bit, "\\_SB.PCI0.SMB0",
+ AddressingMode7Bit, "^",
0x00, ResourceProducer, , Exclusive,
)
})
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Message-Id: <20220608135340.3304695-14-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Message-Id: <20220608135340.3304695-9-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
There is already ISADeviceClass::build_aml() callback which
builds device specific AML blob for some ISA devices.
To extend the same idea to other devices, add TYPE_ACPI_DEV_AML_IF
Interface that will provide a more generic callback which
will be used not only for ISA but other devices. It will
allow get rid of some data-mining and ad-hoc AML building,
by asking device(s) to generate its own AML blob like it's
done for ISA devices.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Message-Id: <20220608135340.3304695-2-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Various loader functions return an int which limits images to 2GB which
is fine for things like a BIOS/kernel image, but if we want to be able
to load memory images or large ramdisks then any file over 2GB would
silently fail to load.
Cc: Luc Michel <lmichel@kalray.eu>
Signed-off-by: Jamie Iles <jamie@nuviainc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Luc Michel <lmichel@kalray.eu>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20211111141141.3295094-2-jamie@nuviainc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This function was declared in a generic and public header, implemented
in a device-specific source file but only used in xen_platform. Given its
'aux' parameter, this function is more xen-specific than piix-specific.
Also, the hardcoded magic constants seem to be generic and related to
PCIIDEState and IDEBus rather than piix.
Therefore, move this function to xen_platform, unexport it, and drop the
"piix3" in the function name as well.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Paul Durrant <paul@xen.org>
Acked-by: Anthony PERARD <anthony.perard@citrix.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20220513180957.90514-4-shentey@gmail.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
Add a periodic timer which raises vblank at a frequency of 30Hz.
Note that this is a migration compatibility break for the
xlnx-zcu102 board type.
Signed-off-by: Sai Pavan Boddu <saipava@xilinx.com>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Frederic Konrad <fkonrad@amd.com>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20220601172353.3220232-3-fkonrad@xilinx.com
Changes by fkonrad:
- Switched to transaction-based ptimer API.
- Added the DP_INT_VBLNK_START macro.
Signed-off-by: Frederic Konrad <fkonrad@amd.com>
[PMM: bump vmstate version, add commit message note about
compat break]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The core and the vblend registers size are wrong, they should respectively be
0x3B0 and 0x1E0 according to:
https://www.xilinx.com/htmldocs/registers/ug1087/ug1087-zynq-ultrascale-registers.html.
Let's fix that and use macros when creating the mmio region.
Fixes: 58ac482a66 ("introduce xlnx-dp")
Signed-off-by: Frederic Konrad <fkonrad@amd.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@amd.com>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20220601172353.3220232-2-fkonrad@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch add ls7a rtc device support.
Signed-off-by: Xiaojuan Yang <yangxiaojuan@loongson.cn>
Signed-off-by: Song Gao <gaosong@loongson.cn>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20220606124333.2060567-39-yangxiaojuan@loongson.cn>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
1.Add uart,virtio-net,vga and usb for 3A5000.
2.Add irq set and map for the pci host. Non pci device
use irq 0-16, pci device use 16-64.
3.Add some unimplented device to emulate guest unused
memory space.
Signed-off-by: Xiaojuan Yang <yangxiaojuan@loongson.cn>
Signed-off-by: Song Gao <gaosong@loongson.cn>
Acked-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20220606124333.2060567-38-yangxiaojuan@loongson.cn>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
This patch realize the EIOINTC interrupt controller.
Signed-off-by: Xiaojuan Yang <yangxiaojuan@loongson.cn>
Signed-off-by: Song Gao <gaosong@loongson.cn>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20220606124333.2060567-35-yangxiaojuan@loongson.cn>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
This patch realize PCH-MSI interrupt controller.
Signed-off-by: Xiaojuan Yang <yangxiaojuan@loongson.cn>
Signed-off-by: Song Gao <gaosong@loongson.cn>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20220606124333.2060567-34-yangxiaojuan@loongson.cn>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
This patch realize the PCH-PIC interrupt controller.
Signed-off-by: Xiaojuan Yang <yangxiaojuan@loongson.cn>
Signed-off-by: Song Gao <gaosong@loongson.cn>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20220606124333.2060567-33-yangxiaojuan@loongson.cn>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
This patch realize the IPI interrupt controller.
Signed-off-by: Xiaojuan Yang <yangxiaojuan@loongson.cn>
Signed-off-by: Song Gao <gaosong@loongson.cn>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20220606124333.2060567-32-yangxiaojuan@loongson.cn>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Emulate a 3A5000 board use the new loongarch instruction.
3A5000 belongs to the Loongson3 series processors.
The board consists of a 3A5000 cpu model and the virt
bridge. The host 3A5000 board is really complicated and
contains many functions.Now for the tcg softmmu mode
only part functions are emulated.
More detailed info you can see
https://github.com/loongson/LoongArch-Documentation
Signed-off-by: Xiaojuan Yang <yangxiaojuan@loongson.cn>
Signed-off-by: Song Gao <gaosong@loongson.cn>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20220606124333.2060567-31-yangxiaojuan@loongson.cn>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
This patch adds support for disassembling via option '-d in_asm'.
Signed-off-by: Song Gao <gaosong@loongson.cn>
Signed-off-by: Xiaojuan Yang <yangxiaojuan@loongson.cn>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20220606124333.2060567-17-yangxiaojuan@loongson.cn>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
This patch decouples checkpoints and async events.
It was a tricky part of replay implementation. Now it becomes
much simpler and easier to maintain.
Signed-off-by: Pavel Dovgalyuk <Pavel.Dovgalyuk@ispras.ru>
Acked-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <165364837856.688121.8785039478408995979.stgit@pasha-ThinkPad-X280>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
vCPU execution should be suspended when new BH is scheduled.
This is needed to avoid guest timeouts caused by the long cycles
of the execution. In replay mode execution may hang when
vCPU sleeps and block event comes to the queue.
This patch adds notification which wakes up vCPU or interrupts
execution of guest code.
Signed-off-by: Pavel Dovgalyuk <Pavel.Dovgalyuk@ispras.ru>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
--
v2: changed first_cpu to current_cpu (suggested by Richard Henderson)
v4: moved vCPU notification to aio_bh_enqueue (suggested by Paolo Bonzini)
Message-Id: <165364837317.688121.17680519919871405281.stgit@pasha-ThinkPad-X280>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
module_kconfig is a new directive that should be used with module_obj
whenever that module depends on the Kconfig to be enabled.
When the module is enabled in Kconfig we are sure that its dependencies
will be enabled as well, thus the module will be loaded without any
problem.
The correct way to use module_kconfig is by passing the Kconfig option
to module_kconfig (or the *config-devices.mak without CONFIG_).
Signed-off-by: Jose R. Ziviani <jziviani@suse.de>
Signed-off-by: Dario Faggioli <dfaggioli@suse.com>
Message-Id: <165369002370.5857.12150544416563557322.stgit@work>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The "-display sdl" option still uses a hand-crafted parser for its
parameters since we didn't want to drag an interface we considered
somewhat flawed into the QAPI schema. Since the flaws are gone now,
it's time to QAPIfy.
This introduces the new "DisplaySDL" QAPI struct that is used to hold
the parameters that are unique to the SDL display. The only specific
parameter is currently "grab-mod" that is used to specify the required
modifier keys to escape from the mouse grabbing mode.
Message-Id: <20220519155625.1414365-3-thuth@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Add an interface to perform moves between TCGv_ptr.
Reviewed-by: Matheus Ferst <matheus.ferst@eldorado.org.br>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
vmbus_save_req() and vmbus_load_req() are not used.
Remove them to avoid maintaining dead code.
This essentially reverts commit 4dd8a7064b
("vmbus: add infrastructure to save/load vmbus requests").
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20211106134155.582312-2-philmd@redhat.com>
[MSS: Remove also corresponding variables, which are now unused]
Signed-off-by: Maciej S. Szmigiero <maciej.szmigiero@oracle.com>
The function is required by get_relocated_path() (already in cutils),
and used by qemu-ga and may be generally useful.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20220525144140.591926-2-marcandre.lureau@redhat.com>
-machine graphics=off is the usual way to tell the firmware or the OS that the
user wants a serial console. The pseries machine however does not support
this, and never adds the stdout-path node to the device tree if a VGA device
is provided. This is in addition to the other magic behavior of VGA devices,
which is to add a keyboard and mouse to the default USB bus.
Split spapr->has_graphics in two variables so that the two behaviors can be
separated: the USB devices remains the same, but the stdout-path is added
even with "-device VGA -machine graphics=off".
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20220507054826.124936-1-pbonzini@redhat.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Introduce new akcipher crypto class 'QCryptoAkCIpher', which supports
basic asymmetric operations: encrypt, decrypt, sign and verify.
Suggested by Daniel P. Berrangé, also add autoptr cleanup for the new
class. Thanks to Daniel!
Co-developed-by: lei he <helei.sig11@bytedance.com>
Signed-off-by: lei he <helei.sig11@bytedance.com>
Signed-off-by: zhenwei pi <pizhenwei@bytedance.com>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
It did not support GPIO index mode for read operation.
Signed-off-by: Jamin Lin <jamin_lin@aspeedtech.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220525053444.27228-4-jamin_lin@aspeedtech.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
AST2400 and AST2500 have 5 UART's, while the AST2600 and AST1030 have 13.
Signed-off-by: Peter Delevoryas <pdel@fb.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220516062328.298336-3-pdel@fb.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This adds the missing UART memory and IRQ mappings for the AST2400, AST2500,
AST2600, and AST1030.
This also includes the new UART interfaces added in the AST2600 and AST1030
from UART6 to UART13. The addresses and interrupt numbers for these two
later chips are identical.
Signed-off-by: Peter Delevoryas <pdel@fb.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220516062328.298336-2-pdel@fb.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
and make routine aspeed_soc_get_irq() common to all SoCs. This will be
useful to share code.
Cc: Jamin Lin <jamin_lin@aspeedtech.com>
Cc: Peter Delevoryas <pdel@fb.com>
Reviewed-by: Peter Delevoryas <pdel@fb.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220516055620.2380197-1-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
* Improve the cleanup of the QEMU binary in case of failing qtests
* Update the Windows support statement
* Remove the capstone submodule (and rely on Capstone of the distros instead)
-----BEGIN PGP SIGNATURE-----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=z6e9
-----END PGP SIGNATURE-----
Merge tag 'pull-request-2022-05-18' of https://gitlab.com/thuth/qemu into staging
* Remove Ubuntu 18.04 containers (not supported anymore)
* Improve the cleanup of the QEMU binary in case of failing qtests
* Update the Windows support statement
* Remove the capstone submodule (and rely on Capstone of the distros instead)
# -----BEGIN PGP SIGNATURE-----
#
# iQJFBAABCAAvFiEEJ7iIR+7gJQEY8+q5LtnXdP5wLbUFAmKEovQRHHRodXRoQHJl
# ZGhhdC5jb20ACgkQLtnXdP5wLbXXtxAAsjL2M/kUcr1KBSfkaMhTa0D3OKPQ+p/e
# Bac/9+l7UhZZLLffzg53lSsCmlj9cSr5cVUkooT7IFS03wauH7ZJ/wuefIS8IYED
# jREmeMWXmVTTfQo4QQZ+6T+XknG2DWjzXQ3sNat71LH4RbHXO5um3zYIdDUaujP+
# v4sAKKH+F/FUsEXMP1rFmZpkaWOcvsuSwP/H4kEfhlovebAZINPow26eYYRrTM2t
# Ifs7HelO12TlmqlBFn0UzHj8bV8MZkqcjj0efocVzuYMQ8DVcxE7IPc3tft2PuUu
# Ia+Czh1hLsLA1zYiO/nN9bVIIewFGOErASzjlYWUlQwNRc1nLik+m+p4Cl9WOEhL
# JpkN/yY3pTI5uC6a4KgxDQGTeFUR4D5la6Hg7yQjQbTBMEeGFCV50iOdkItdnRBx
# ByReVctXS3oIhsDqHMb8qydlBkPp5pUrAXdj43IBCUb3UsrHmCxH+z8U5BhHvv4D
# OleykLKyMcuff6HcEpC1fBQNIFJX5uS69EtAXYtyo2kb5zAJWezCv65UPldAZJCT
# kRT4beueQ+d5t+4LZn1qNePdoyeFArdCLlOqg/3Fx08kM5eEv22pSQhOtWclE7U3
# tgorikFybClvKJ+YnXBAxD7oFKe+h9L+RYCFOgoTebrbMX54IjjJfeo2DydhHTt7
# IaJnsI+vvAA=
# =z6e9
# -----END PGP SIGNATURE-----
# gpg: Signature made Wed 18 May 2022 12:40:36 AM PDT
# gpg: using RSA key 27B88847EEE0250118F3EAB92ED9D774FE702DB5
# gpg: issuer "thuth@redhat.com"
# gpg: Good signature from "Thomas Huth <th.huth@gmx.de>" [undefined]
# gpg: aka "Thomas Huth <thuth@redhat.com>" [undefined]
# gpg: aka "Thomas Huth <th.huth@posteo.de>" [unknown]
# gpg: aka "Thomas Huth <huth@tuxfamily.org>" [undefined]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 27B8 8847 EEE0 2501 18F3 EAB9 2ED9 D774 FE70 2DB5
* tag 'pull-request-2022-05-18' of https://gitlab.com/thuth/qemu:
capstone: Remove the capstone submodule
capstone: Allow version 3.0.5 again
tests/vm: Add capstone to the NetBSD and OpenBSD VMs
docs/about: Update the support statement for Windows
tests/qtest: use prctl(PR_SET_PDEATHSIG) as fallback to kill QEMU
tests/qtest: fix registration of ABRT handler for QEMU cleanup
Remove Ubuntu 18.04 container support from the repository
gitlab-ci: Switch the container of the 'check-patch' & 'check-dco' jobs
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
The traditional ptimer behaviour includes a collection of weird edge
case behaviours. In 2016 we improved the ptimer implementation to
fix these and generally make the behaviour more flexible, with
ptimers opting in to the new behaviour by passing an appropriate set
of policy flags to ptimer_init(). For backwards-compatibility, we
defined PTIMER_POLICY_DEFAULT (which sets no flags) to give the old
weird behaviour.
This turns out to be a poor choice of name, because people writing
new devices which use ptimers are misled into thinking that the
default is probably a sensible choice of flags, when in fact it is
almost always not what you want. Rename PTIMER_POLICY_DEFAULT to
PTIMER_POLICY_LEGACY and beef up the comment to more clearly say that
new devices should not be using it.
The code-change part of this commit was produced by
sed -i -e 's/PTIMER_POLICY_DEFAULT/PTIMER_POLICY_LEGACY/g' $(git grep -l PTIMER_POLICY_DEFAULT)
with the exception of a test name string change in
tests/unit/ptimer-test.c which was added manually.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Francisco Iglesias <francisco.iglesias@amd.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220516103058.162280-1-peter.maydell@linaro.org
Except hw/core/irq.c which implements the forward-declared opaque
qemu_irq structure, hw/adc/zynq-xadc.{c,h} are the only files not
using the typedef. Fix this single exception.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Bernhard Beschow <shentey@gmail.com>
Message-id: 20220509202035.50335-1-philippe.mathieu.daude@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Make the GICv3 set its number of bits of physical priority from the
implementation-specific value provided in the CPU state struct, in
the same way we already do for virtual priority bits. Because this
would be a migration compatibility break, we provide a property
force-8-bit-prio which is enabled for 7.0 and earlier versioned board
models to retain the legacy "always use 8 bits" behaviour.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220512151457.3899052-6-peter.maydell@linaro.org
Message-id: 20220506162129.2896966-5-peter.maydell@linaro.org
The GICv3 code has always supported a configurable number of virtual
priority and preemption bits, but our implementation currently
hardcodes the number of physical priority bits at 8. This is not
what most hardware implementations provide; for instance the
Cortex-A53 provides only 5 bits of physical priority.
Make the number of physical priority/preemption bits driven by fields
in the GICv3CPUState, the way that we already do for virtual
priority/preemption bits. We set cs->pribits to 8, so there is no
behavioural change in this commit. A following commit will add the
machinery for CPUs to set this to the correct value for their
implementation.
Note that changing the number of priority bits would be a migration
compatibility break, because the semantics of the icc_apr[][] array
changes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220512151457.3899052-5-peter.maydell@linaro.org
Message-id: 20220506162129.2896966-4-peter.maydell@linaro.org
Our support statement for Windows currently talks about "Vista / Server
2008" - which is related to the API of Windows, and this is not easy
to understand for the non-technical users. Additionally, glib sets the
_WIN32_WINNT macro to 0x0601 already, which indicates the Windows 7 API,
so QEMU effectively depends on the Windows 7 API, too.
Thus let's bump the _WIN32_WINNT setting in QEMU to the same level as
glib uses and adjust our support statement in the documentation to
something similar that we're using for Linux and the *BSD systems
(i.e. only the two most recent versions), which should hopefully be
easier to understand for the users now.
And since we're nowadays also compile-testing QEMU with MSYS2 on Windows
itself, I think we could mention this build environment here, too.
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/880
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Stefan Weil <sw@weilnetz.de>
Message-Id: <20220513063958.1181443-1-thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
most of CXL support
fixes, cleanups all over the place
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAmKCuLIPHG1zdEByZWRo
YXQuY29tAAoJECgfDbjSjVRpdDUH/12SmWaAo+0+SdIHgWFFxsmg3t/EdcO38fgi
MV+GpYdbp6TlU3jdQhrMZYmFdkVVydBdxk93ujCLbFS0ixTsKj31j0IbZMfdcGgv
SLqnV+E3JdHqnGP39q9a9rdwYWyqhkgHoldxilIFW76ngOSapaZVvnwnOMAMkf77
1LieL4/Xq7N9Ho86Zrs3IczQcf0czdJRDaFaSIu8GaHl8ELyuPhlSm6CSqqrEEWR
PA/COQsLDbLOMxbfCi5v88r5aaxmGNZcGbXQbiH9qVHw65nlHyLH9UkNTdJn1du1
f2GYwwa7eekfw/LCvvVwxO1znJrj02sfFai7aAtQYbXPvjvQiqA=
=xdSk
-----END PGP SIGNATURE-----
Merge tag 'for_upstream' of git://git.kernel.org/pub/scm/virt/kvm/mst/qemu into staging
virtio,pc,pci: fixes,cleanups,features
most of CXL support
fixes, cleanups all over the place
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# -----BEGIN PGP SIGNATURE-----
#
# iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAmKCuLIPHG1zdEByZWRo
# YXQuY29tAAoJECgfDbjSjVRpdDUH/12SmWaAo+0+SdIHgWFFxsmg3t/EdcO38fgi
# MV+GpYdbp6TlU3jdQhrMZYmFdkVVydBdxk93ujCLbFS0ixTsKj31j0IbZMfdcGgv
# SLqnV+E3JdHqnGP39q9a9rdwYWyqhkgHoldxilIFW76ngOSapaZVvnwnOMAMkf77
# 1LieL4/Xq7N9Ho86Zrs3IczQcf0czdJRDaFaSIu8GaHl8ELyuPhlSm6CSqqrEEWR
# PA/COQsLDbLOMxbfCi5v88r5aaxmGNZcGbXQbiH9qVHw65nlHyLH9UkNTdJn1du1
# f2GYwwa7eekfw/LCvvVwxO1znJrj02sfFai7aAtQYbXPvjvQiqA=
# =xdSk
# -----END PGP SIGNATURE-----
# gpg: Signature made Mon 16 May 2022 01:48:50 PM PDT
# gpg: using RSA key 5D09FD0871C8F85B94CA8A0D281F0DB8D28D5469
# gpg: issuer "mst@redhat.com"
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>" [undefined]
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>" [undefined]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* tag 'for_upstream' of git://git.kernel.org/pub/scm/virt/kvm/mst/qemu: (86 commits)
vhost-user-scsi: avoid unlink(NULL) with fd passing
virtio-net: don't handle mq request in userspace handler for vhost-vdpa
vhost-vdpa: change name and polarity for vhost_vdpa_one_time_request()
vhost-vdpa: backend feature should set only once
vhost-net: fix improper cleanup in vhost_net_start
vhost-vdpa: fix improper cleanup in net_init_vhost_vdpa
virtio-net: align ctrl_vq index for non-mq guest for vhost_vdpa
virtio-net: setup vhost_dev and notifiers for cvq only when feature is negotiated
hw/i386/amd_iommu: Fix IOMMU event log encoding errors
hw/i386: Make pic a property of common x86 base machine type
hw/i386: Make pit a property of common x86 base machine type
include/hw/pci/pcie_host: Correct PCIE_MMCFG_SIZE_MAX
include/hw/pci/pcie_host: Correct PCIE_MMCFG_BUS_MASK
docs/vhost-user: Clarifications for VHOST_USER_ADD/REM_MEM_REG
vhost-user: more master/slave things
virtio: add vhost support for virtio devices
virtio: drop name parameter for virtio_init()
virtio/vhost-user: dynamically assign VhostUserHostNotifiers
hw/virtio/vhost-user: don't suppress F_CONFIG when supported
include/hw: start documenting the vhost API
...
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
* misc qga-vss fixes
* remove the deprecated CPU model 'Icelake-Client'
* support for x86 architectural LBR
* remove deprecated properties
* replace deprecated -soundhw with -audio
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEE8TM4V0tmI4mGbHaCv/vSX3jHroMFAmJ/hZ4UHHBib256aW5p
QHJlZGhhdC5jb20ACgkQv/vSX3jHroN2Igf/bFs+yluOikt0eFNmXYnshrGBWPXr
oam0iumPox34vTzZnjpSjF6tJGxHWOgi+wbgIvbwOYHA/ONxx8akW580j+1VhEWa
X29VyUzjZBffgFtmlF4fM74/ELYm7s4c1a1/D9TpVP6Dr0fSWbMujbx4dfeVstvf
sONN+A8sVxaNdV9QKPE6BvqfMlPLoCiigrOetf6iY1KuUtkQDF8xDB0MdzdutqAQ
szAtQ0rrzjxDx9EuGN1SECFM1/riDUbtOOoA9g2C7gGKrx3/iUc6pzrkIcAfWLFK
xXbH7+6Wynia0cbUxnrvRdY4daMIxm4N3wUvN7szXgF9kxYxeQcsdgGsNA==
=n4lu
-----END PGP SIGNATURE-----
Merge tag 'for-upstream' of https://gitlab.com/bonzini/qemu into staging
* fix WHPX debugging
* misc qga-vss fixes
* remove the deprecated CPU model 'Icelake-Client'
* support for x86 architectural LBR
* remove deprecated properties
* replace deprecated -soundhw with -audio
# -----BEGIN PGP SIGNATURE-----
#
# iQFIBAABCAAyFiEE8TM4V0tmI4mGbHaCv/vSX3jHroMFAmJ/hZ4UHHBib256aW5p
# QHJlZGhhdC5jb20ACgkQv/vSX3jHroN2Igf/bFs+yluOikt0eFNmXYnshrGBWPXr
# oam0iumPox34vTzZnjpSjF6tJGxHWOgi+wbgIvbwOYHA/ONxx8akW580j+1VhEWa
# X29VyUzjZBffgFtmlF4fM74/ELYm7s4c1a1/D9TpVP6Dr0fSWbMujbx4dfeVstvf
# sONN+A8sVxaNdV9QKPE6BvqfMlPLoCiigrOetf6iY1KuUtkQDF8xDB0MdzdutqAQ
# szAtQ0rrzjxDx9EuGN1SECFM1/riDUbtOOoA9g2C7gGKrx3/iUc6pzrkIcAfWLFK
# xXbH7+6Wynia0cbUxnrvRdY4daMIxm4N3wUvN7szXgF9kxYxeQcsdgGsNA==
# =n4lu
# -----END PGP SIGNATURE-----
# gpg: Signature made Sat 14 May 2022 03:34:06 AM PDT
# gpg: using RSA key F13338574B662389866C7682BFFBD25F78C7AE83
# gpg: issuer "pbonzini@redhat.com"
# gpg: Good signature from "Paolo Bonzini <bonzini@gnu.org>" [undefined]
# gpg: aka "Paolo Bonzini <pbonzini@redhat.com>" [undefined]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 46F5 9FBD 57D6 12E7 BFD4 E2F7 7E15 100C CD36 69B1
# Subkey fingerprint: F133 3857 4B66 2389 866C 7682 BFFB D25F 78C7 AE83
* tag 'for-upstream' of https://gitlab.com/bonzini/qemu: (23 commits)
configure: remove duplicate help messages
configure: remove another dead variable
build: remove useless dependency
introduce -audio as a replacement for -soundhw
soundhw: move help handling to vl.c
soundhw: unify initialization for ISA and PCI soundhw
soundhw: extract soundhw help to a separate function
soundhw: remove ability to create multiple soundcards
rng: make opened property read-only
crypto: make loaded property read-only
target/i386: Support Arch LBR in CPUID enumeration
target/i386: introduce helper to access supported CPUID
target/i386: Enable Arch LBR migration states in vmstate
target/i386: Add MSR access interface for Arch LBR
target/i386: Add XSAVES support for Arch LBR
target/i386: Enable support for XSAVES based features
target/i386: Add kvm_get_one_msr helper
target/i386: Add lbr-fmt vPMU option to support guest LBR
qdev-properties: Add a new macro with bitmask check for uint64_t property
i386/cpu: Remove the deprecated cpu model 'Icelake-Client'
...
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Legacy PIC (8259) cannot be supported for TDX guests since TDX module
doesn't allow directly interrupt injection. Using posted interrupts
for the PIC is not a viable option as the guest BIOS/kernel will not
do EOI for PIC IRQs, i.e. will leave the vIRR bit set.
Make PIC the property of common x86 machine type. Hence all x86
machines, including microvm, can disable it.
Signed-off-by: Xiaoyao Li <xiaoyao.li@intel.com>
Reviewed-by: Sergio Lopez <slp@redhat.com>
Message-Id: <20220310122811.807794-3-xiaoyao.li@intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Both pc and microvm have pit property individually. Let's just make it
the property of common x86 base machine type.
Signed-off-by: Xiaoyao Li <xiaoyao.li@intel.com>
Reviewed-by: Sergio Lopez <slp@redhat.com>
Message-Id: <20220310122811.807794-2-xiaoyao.li@intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
According to 7.2.2 in [1] bit 27 is the last bit that can be part of the
bus number, this makes the ECAM max size equal to '1 << 28'. This patch
restores back this value into the PCIE_MMCFG_SIZE_MAX define (which was
changed in commit 58d5b22bbd ("ppc4xx: Add device models found in PPC440
core SoCs")).
[1] PCI Express® Base Specification Revision 5.0 Version 1.0
Signed-off-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Message-Id: <20220411221836.17699-3-frasse.iglesias@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
According to [1] address bits 27 - 20 are mapped to the bus number (the
TLPs bus number field is 8 bits). Below is the formula taken from Table
7-1 in [1].
"
Memory Address | PCI Express Configuration Space
A[(20+n-1):20] | Bus Number, 1 ≤ n ≤ 8
"
[1] PCI Express® Base Specification Revision 5.0 Version 1.0
Signed-off-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Message-Id: <20220411221836.17699-2-frasse.iglesias@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
For CONFIG_LINUX, implement the new zero copy flag and the optional callback
io_flush on QIOChannelSocket, but enables it only when MSG_ZEROCOPY
feature is available in the host kernel, which is checked on
qio_channel_socket_connect_sync()
qio_channel_socket_flush() was implemented by counting how many times
sendmsg(...,MSG_ZEROCOPY) was successfully called, and then reading the
socket's error queue, in order to find how many of them finished sending.
Flush will loop until those counters are the same, or until some error occurs.
Notes on using writev() with QIO_CHANNEL_WRITE_FLAG_ZERO_COPY:
1: Buffer
- As MSG_ZEROCOPY tells the kernel to use the same user buffer to avoid copying,
some caution is necessary to avoid overwriting any buffer before it's sent.
If something like this happen, a newer version of the buffer may be sent instead.
- If this is a problem, it's recommended to call qio_channel_flush() before freeing
or re-using the buffer.
2: Locked memory
- When using MSG_ZERCOCOPY, the buffer memory will be locked after queued, and
unlocked after it's sent.
- Depending on the size of each buffer, and how often it's sent, it may require
a larger amount of locked memory than usually available to non-root user.
- If the required amount of locked memory is not available, writev_zero_copy
will return an error, which can abort an operation like migration,
- Because of this, when an user code wants to add zero copy as a feature, it
requires a mechanism to disable it, so it can still be accessible to less
privileged users.
Signed-off-by: Leonardo Bras <leobras@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20220513062836.965425-4-leobras@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Add flags to io_writev and introduce io_flush as optional callback to
QIOChannelClass, allowing the implementation of zero copy writes by
subclasses.
How to use them:
- Write data using qio_channel_writev*(...,QIO_CHANNEL_WRITE_FLAG_ZERO_COPY),
- Wait write completion with qio_channel_flush().
Notes:
As some zero copy write implementations work asynchronously, it's
recommended to keep the write buffer untouched until the return of
qio_channel_flush(), to avoid the risk of sending an updated buffer
instead of the buffer state during write.
As io_flush callback is optional, if a subclass does not implement it, then:
- io_flush will return 0 without changing anything.
Also, some functions like qio_channel_writev_full_all() were adapted to
receive a flag parameter. That allows shared code between zero copy and
non-zero copy writev, and also an easier implementation on new flags.
Signed-off-by: Leonardo Bras <leobras@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20220513062836.965425-3-leobras@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
This patch adds a get_vhost() callback function for VirtIODevices that
returns the device's corresponding vhost_dev structure, if the vhost
device is running. This patch also adds a vhost_started flag for
VirtIODevices.
Previously, a VirtIODevice wouldn't be able to tell if its corresponding
vhost device was active or not.
Signed-off-by: Jonah Palmer <jonah.palmer@oracle.com>
Message-Id: <1648819405-25696-3-git-send-email-jonah.palmer@oracle.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This patch drops the name parameter for the virtio_init function.
The pair between the numeric device ID and the string device ID
(name) of a virtio device already exists, but not in a way that
lets us map between them.
This patch lets us do this and removes the need for the name
parameter in the virtio_init function.
Signed-off-by: Jonah Palmer <jonah.palmer@oracle.com>
Message-Id: <1648819405-25696-2-git-send-email-jonah.palmer@oracle.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
At a couple of hundred bytes per notifier allocating one for every
potential queue is very wasteful as most devices only have a few
queues. Instead of having this handled statically dynamically assign
them and track in a GPtrArray.
[AJB: it's hard to trigger the vhost notifiers code, I assume as it
requires a KVM guest with appropriate backend]
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20220321153037.3622127-14-alex.bennee@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Previously we would silently suppress VHOST_USER_PROTOCOL_F_CONFIG
during the protocol negotiation if the QEMU stub hadn't implemented
the vhost_dev_config_notifier. However this isn't the only way we can
handle config messages, the existing vdc->get/set_config can do this
as well.
Lightly re-factor the code to check for both potential methods and
instead of silently squashing the feature error out. It is unlikely
that a vhost-user backend expecting to handle CONFIG messages will
behave correctly if they never get sent.
Fixes: 1c3e5a2617 ("vhost-user: back SET/GET_CONFIG requests with a protocol feature")
Cc: Maxime Coquelin <maxime.coquelin@redhat.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20220321153037.3622127-13-alex.bennee@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
While trying to get my head around the nest of interactions for vhost
devices I though I could start by documenting the key API functions.
This patch documents the main API hooks for creating and starting a
vhost device as well as how the configuration changes are handled.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Stefan Hajnoczi <stefanha@redhat.com>
Cc: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20220321153037.3622127-11-alex.bennee@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This allows other device classes that will be exposed via PCI to be
able to do so in the appropriate hw/ directory. I resisted the
temptation to re-order headers to be more aesthetically pleasing.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20200925125147.26943-4-alex.bennee@linaro.org>
Message-Id: <20220321153037.3622127-2-alex.bennee@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
By setting none of the SAGAW bits we can indicate to a guest that DMA
translation isn't supported. Tested by booting Windows 10, as well as
Linux guests with the fix at https://git.kernel.org/torvalds/c/c40aaaac10
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Peter Xu <peterx@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20220314142544.150555-2-dwmw2@infradead.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-audio is used like "-audio pa,model=sb16". It is almost as simple as
-soundhw, but it reuses the -audiodev parsing machinery and attaches an
audiodev to the newly-created device. The main 'feature' is that
it knows about adding the codec device for model=intel-hda, and adding
the audiodev to the codec device.
In the future, it could be extended to support default models or
builtin devices, just like -nic, or even a default backend. For now,
keep it simple.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The DEFINE_PROP_UINT64_CHECKMASK maro applies certain mask check agaist
user-supplied property value, reject the value if it violates the bitmask.
Co-developed-by: Like Xu <like.xu@linux.intel.com>
Signed-off-by: Like Xu <like.xu@linux.intel.com>
Signed-off-by: Yang Weijiang <weijiang.yang@intel.com>
Message-Id: <20220215195258.29149-2-weijiang.yang@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Update to c5eb0a61238d ("Linux 5.18-rc6"). Mechanical search and
replace of vfio defines with white space massaging.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
These memops perform interleave decoding, walking down the
CXL topology from CFMWS described host interleave
decoder via CXL host bridge HDM decoders, through the CXL
root ports and finally call CXL type 3 specific read and write
functions.
Note that, whilst functional the current implementation does
not support:
* switches
* multiple HDM decoders at a given level.
* unaligned accesses across the interleave boundaries
Signed-off-by: Jonathan Cameron <jonathan.cameron@huawei.com>
Message-Id: <20220429144110.25167-34-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Once a read or write reaches a CXL type 3 device, the HDM decoders
on the device are used to establish the Device Physical Address
which should be accessed. These functions peform the required maths
and then use a device specific address space to access the
hostmem->mr to fullfil the actual operation. Note that failed writes
are silent, but failed reads return poison. Note this is based
loosely on:
https://lore.kernel.org/qemu-devel/20200817161853.593247-6-f4bug@amsat.org/
[RFC PATCH 0/9] hw/misc: Add support for interleaved memory accesses
Only lightly tested so far. More complex test cases yet to be written.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20220429144110.25167-33-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Accessor to get hold of the cxl state for a CXL host bridge
without exposing the internals of the implementation.
Signed-off-by: Jonathan Cameron <jonathan.cameron@huawei.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20220429144110.25167-32-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Simple function to search a PCIBus to find a port by
it's port number.
CXL interleave decoding uses the port number as a target
so it is necessary to locate the port when doing interleave
decoding.
Signed-off-by: Jonathan Cameron <jonathan.cameron@huawei.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20220429144110.25167-31-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The concept of these is introduced in [1] in terms of the
description the CEDT ACPI table. The principal is more general.
Unlike once traffic hits the CXL root bridges, the host system
memory address routing is implementation defined and effectively
static once observable by standard / generic system software.
Each CXL Fixed Memory Windows (CFMW) is a region of PA space
which has fixed system dependent routing configured so that
accesses can be routed to the CXL devices below a set of target
root bridges. The accesses may be interleaved across multiple
root bridges.
For QEMU we could have fully specified these regions in terms
of a base PA + size, but as the absolute address does not matter
it is simpler to let individual platforms place the memory regions.
ExampleS:
-cxl-fixed-memory-window targets.0=cxl.0,size=128G
-cxl-fixed-memory-window targets.0=cxl.1,size=128G
-cxl-fixed-memory-window targets.0=cxl0,targets.1=cxl.1,size=256G,interleave-granularity=2k
Specifies
* 2x 128G regions not interleaved across root bridges, one for each of
the root bridges with ids cxl.0 and cxl.1
* 256G region interleaved across root bridges with ids cxl.0 and cxl.1
with a 2k interleave granularity.
When system software enumerates the devices below a given root bridge
it can then decide which CFMW to use. If non interleave is desired
(or possible) it can use the appropriate CFMW for the root bridge in
question. If there are suitable devices to interleave across the
two root bridges then it may use the 3rd CFMS.
A number of other designs were considered but the following constraints
made it hard to adapt existing QEMU approaches to this particular problem.
1) The size must be known before a specific architecture / board brings
up it's PA memory map. We need to set up an appropriate region.
2) Using links to the host bridges provides a clean command line interface
but these links cannot be established until command line devices have
been added.
Hence the two step process used here of first establishing the size,
interleave-ways and granularity + caching the ids of the host bridges
and then, once available finding the actual host bridges so they can
be used later to support interleave decoding.
[1] CXL 2.0 ECN: CEDT CFMWS & QTG DSM (computeexpresslink.org / specifications)
Signed-off-by: Jonathan Cameron <jonathan.cameron@huawei.com>
Acked-by: Markus Armbruster <armbru@redhat.com> # QAPI Schema
Message-Id: <20220429144110.25167-28-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Both registers and the CFMWS entries in CDAT use simple encodings
for the number of interleave ways and the interleave granularity.
Introduce simple conversion functions to/from the unencoded
number / size. So far the iw decode has not been needed so is
it not implemented.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20220429144110.25167-27-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The CXL Early Discovery Table is defined in the CXL 2.0 specification as
a way for the OS to get CXL specific information from the system
firmware.
CXL 2.0 specification adds an _HID, ACPI0016, for CXL capable host
bridges, with a _CID of PNP0A08 (PCIe host bridge). CXL aware software
is able to use this initiate the proper _OSC method, and get the _UID
which is referenced by the CEDT. Therefore the existence of an ACPI0016
device allows a CXL aware driver perform the necessary actions. For a
CXL capable OS, this works. For a CXL unaware OS, this works.
CEDT awaremess requires more. The motivation for ACPI0017 is to provide
the possibility of having a Linux CXL module that can work on a legacy
Linux kernel. Linux core PCI/ACPI which won't be built as a module,
will see the _CID of PNP0A08 and bind a driver to it. If we later loaded
a driver for ACPI0016, Linux won't be able to bind it to the hardware
because it has already bound the PNP0A08 driver. The ACPI0017 device is
an opportunity to have an object to bind a driver will be used by a
Linux driver to walk the CXL topology and do everything that we would
have preferred to do with ACPI0016.
There is another motivation for an ACPI0017 device which isn't
implemented here. An operating system needs an attach point for a
non-volatile region provider that understands cross-hostbridge
interleaving. Since QEMU emulation doesn't support interleaving yet,
this is more important on the OS side, for now.
As of CXL 2.0 spec, only 1 sub structure is defined, the CXL Host Bridge
Structure (CHBS) which is primarily useful for telling the OS exactly
where the MMIO for the host bridge is.
Link: https://lore.kernel.org/linux-cxl/20210115034911.nkgpzc756d6qmjpl@intel.com/T/#t
Signed-off-by: Ben Widawsky <ben.widawsky@intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20220429144110.25167-26-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
CXL host bridges themselves may have MMIO. Since host bridges don't have
a BAR they are treated as special for MMIO. This patch includes
i386/pc support.
Also hook up the device reset now that we have have the MMIO
space in which the results are visible.
Note that we duplicate the PCI express case for the aml_build but
the implementations will diverge when the CXL specific _OSC is
introduced.
Signed-off-by: Ben Widawsky <ben.widawsky@intel.com>
Co-developed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20220429144110.25167-24-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Implement get and set handlers for the Label Storage Area
used to hold data describing persistent memory configuration
so that it can be ensured it is seen in the same configuration
after reboot.
Signed-off-by: Ben Widawsky <ben.widawsky@intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20220429144110.25167-22-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This should introduce no change. Subsequent work will make use of this
new class member.
Signed-off-by: Ben Widawsky <ben.widawsky@intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20220429144110.25167-21-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
A CXL memory device (AKA Type 3) is a CXL component that contains some
combination of volatile and persistent memory. It also implements the
previously defined mailbox interface as well as the memory device
firmware interface.
Although the memory device is configured like a normal PCIe device, the
memory traffic is on an entirely separate bus conceptually (using the
same physical wires as PCIe, but different protocol).
Once the CXL topology is fully configure and address decoders committed,
the guest physical address for the memory device is part of a larger
window which is owned by the platform. The creation of these windows
is later in this series.
The following example will create a 256M device in a 512M window:
-object "memory-backend-file,id=cxl-mem1,share,mem-path=cxl-type3,size=512M"
-device "cxl-type3,bus=rp0,memdev=cxl-mem1,id=cxl-pmem0"
Note: Dropped PCDIMM info interfaces for now. They can be added if
appropriate at a later date.
Signed-off-by: Ben Widawsky <ben.widawsky@intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20220429144110.25167-18-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This works like adding a typical pxb device, except the name is
'pxb-cxl' instead of 'pxb-pcie'. An example command line would be as
follows:
-device pxb-cxl,id=cxl.0,bus="pcie.0",bus_nr=1
A CXL PXB is backward compatible with PCIe. What this means in practice
is that an operating system that is unaware of CXL should still be able
to enumerate this topology as if it were PCIe.
One can create multiple CXL PXB host bridges, but a host bridge can only
be connected to the main root bus. Host bridges cannot appear elsewhere
in the topology.
Note that as of this patch, the ACPI tables needed for the host bridge
(specifically, an ACPI object in _SB named ACPI0016 and the CEDT) aren't
created. So while this patch internally creates it, it cannot be
properly used by an operating system or other system software.
Also necessary is to add an exception to scripts/device-crash-test
similar to that for exiting pxb as both must created on a PCIexpress
host bus.
Signed-off-by: Ben Widawsky <ben.widawsky@intel.com>
Signed-off-by: Jonathan.Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20220429144110.25167-15-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
There are going to be some potential overheads to CXL enablement,
for example the host bridge region reserved in memory maps.
Add a machine level control so that CXL is disabled by default.
Signed-off-by: Jonathan Cameron <jonathan.cameron@huawei.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20220429144110.25167-14-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The easiest way to differentiate a CXL bus, and a PCIE bus is using a
flag. A CXL bus, in hardware, is backward compatible with PCIE, and
therefore the code tries pretty hard to keep them in sync as much as
possible.
The other way to implement this would be to try to cast the bus to the
correct type. This is less code and useful for debugging via simply
looking at the flags.
Signed-off-by: Ben Widawsky <ben.widawsky@intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20220429144110.25167-13-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Errata F4 to CXL 2.0 clarified the meaning of the timer as the
sum of the value set with the timestamp set command and the number
of nano seconds since it was last set.
Signed-off-by: Ben Widawsky <ben.widawsky@intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20220429144110.25167-10-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Memory devices implement extra capabilities on top of CXL devices. This
adds support for that.
A large part of memory devices is the mailbox/command interface. All of
the mailbox handling is done in the mailbox-utils library. Longer term,
new CXL devices that are being emulated may want to handle commands
differently, and therefore would need a mechanism to opt in/out of the
specific generic handlers. As such, this is considered sufficient for
now, but may need more depth in the future.
Signed-off-by: Ben Widawsky <ben.widawsky@intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20220429144110.25167-8-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This is the beginning of implementing mailbox support for CXL 2.0
devices. The implementation recognizes when the doorbell is rung,
handles the command/payload, clears the doorbell while returning error
codes and data.
Generally the mailbox mechanism is designed to permit communication
between the host OS and the firmware running on the device. For our
purposes, we emulate both the firmware, implemented primarily in
cxl-mailbox-utils.c, and the hardware.
No commands are implemented yet.
Signed-off-by: Ben Widawsky <ben.widawsky@intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20220429144110.25167-7-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This implements all device MMIO up to the first capability. That
includes the CXL Device Capabilities Array Register, as well as all of
the CXL Device Capability Header Registers. The latter are filled in as
they are implemented in the following patches.
Endianness and alignment are managed by softmmu memory core.
Signed-off-by: Ben Widawsky <ben.widawsky@intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20220429144110.25167-6-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
A CXL device is a type of CXL component. Conceptually, a CXL device
would be a leaf node in a CXL topology. From an emulation perspective,
CXL devices are the most complex and so the actual implementation is
reserved for discrete commits.
This new device type is specifically catered towards the eventual
implementation of a Type3 CXL.mem device, 8.2.8.5 in the CXL 2.0
specification.
Signed-off-by: Ben Widawsky <ben.widawsky@intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Adam Manzanares <a.manzanares@samsung.com>
Message-Id: <20220429144110.25167-5-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
A CXL 2.0 component is any entity in the CXL topology. All components
have a analogous function in PCIe. Except for the CXL host bridge, all
have a PCIe config space that is accessible via the common PCIe
mechanisms. CXL components are enumerated via DVSEC fields in the
extended PCIe header space. CXL components will minimally implement some
subset of CXL.mem and CXL.cache registers defined in 8.2.5 of the CXL
2.0 specification. Two headers and a utility library are introduced to
support the minimum functionality needed to enumerate components.
The cxl_pci header manages bits associated with PCI, specifically the
DVSEC and related fields. The cxl_component.h variant has data
structures and APIs that are useful for drivers implementing any of the
CXL 2.0 components. The library takes care of making use of the DVSEC
bits and the CXL.[mem|cache] registers. Per spec, the registers are
little endian.
None of the mechanisms required to enumerate a CXL capable hostbridge
are introduced at this point.
Note that the CXL.mem and CXL.cache registers used are always 4B wide.
It's possible in the future that this constraint will not hold.
Signed-off-by: Ben Widawsky <ben.widawsky@intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Adam Manzanares <a.manzanares@samsung.com>
Message-Id: <20220429144110.25167-3-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
A CXL component is a hardware entity that implements CXL component
registers from the CXL 2.0 spec (8.2.3). Currently these represent 3
general types.
1. Host Bridge
2. Ports (root, upstream, downstream)
3. Devices (memory, other)
A CXL component can be conceptually thought of as a PCIe device with
extra functionality when enumerated and enabled. For this reason, CXL
does here, and will continue to add on to existing PCI code paths.
Host bridges will typically need to be handled specially and so they can
implement this newly introduced interface or not. All other components
should implement this interface. Implementing this interface allows the
core PCI code to treat these devices as special where appropriate.
Signed-off-by: Ben Widawsky <ben.widawsky@intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Adam Manzanares <a.manzanares@samsung.com>
Message-Id: <20220429144110.25167-2-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
According to the NBD spec, a server that advertises
NBD_FLAG_CAN_MULTI_CONN promises that multiple client connections will
not see any cache inconsistencies: when properly separated by a single
flush, actions performed by one client will be visible to another
client, regardless of which client did the flush.
We always satisfy these conditions in qemu - even when we support
multiple clients, ALL clients go through a single point of reference
into the block layer, with no local caching. The effect of one client
is instantly visible to the next client. Even if our backend were a
network device, we argue that any multi-path caching effects that
would cause inconsistencies in back-to-back actions not seeing the
effect of previous actions would be a bug in that backend, and not the
fault of caching in qemu. As such, it is safe to unconditionally
advertise CAN_MULTI_CONN for any qemu NBD server situation that
supports parallel clients.
Note, however, that we don't want to advertise CAN_MULTI_CONN when we
know that a second client cannot connect (for historical reasons,
qemu-nbd defaults to a single connection while nbd-server-add and QMP
commands default to unlimited connections; but we already have
existing means to let either style of NBD server creation alter those
defaults). This is visible by no longer advertising MULTI_CONN for
'qemu-nbd -r' without -e, as in the iotest nbd-qemu-allocation.
The harder part of this patch is setting up an iotest to demonstrate
behavior of multiple NBD clients to a single server. It might be
possible with parallel qemu-io processes, but I found it easier to do
in python with the help of libnbd, and help from Nir and Vladimir in
writing the test.
Signed-off-by: Eric Blake <eblake@redhat.com>
Suggested-by: Nir Soffer <nsoffer@redhat.com>
Suggested-by: Vladimir Sementsov-Ogievskiy <v.sementsov-og@mail.ru>
Message-Id: <20220512004924.417153-3-eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The next patch wants to adjust whether the NBD server code advertises
MULTI_CONN based on whether it is known if the server limits to
exactly one client. For a server started by QMP, this information is
obtained through nbd_server_start (which can support more than one
export); but for qemu-nbd (which supports exactly one export), it is
controlled only by the command-line option -e/--shared. Since we
already have a hook function used by qemu-nbd, it's easiest to just
alter its signature to fit our needs.
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <20220512004924.417153-2-eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
qemu_co_queue_restart_all is basically the same as qemu_co_enter_all
but without a QemuLockable argument. That's perfectly fine, but only as
long as the function is marked coroutine_fn. If used outside coroutine
context, qemu_co_queue_wait will attempt to take the lock and that
is just broken: if you are calling qemu_co_queue_restart_all outside
coroutine context, the lock is going to be a QemuMutex which cannot be
taken twice by the same thread.
The patch adds the marker to qemu_co_queue_restart_all and to its sole
non-coroutine_fn caller; it then reimplements the function in terms of
qemu_co_enter_all_impl, to remove duplicated code and to clarify that the
latter also works in coroutine context.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <20220427130830.150180-4-pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Because qemu_co_queue_restart_all does not release the lock, it should
be used only in coroutine context. Introduce a new function that,
like qemu_co_enter_next, does release the lock, and use it whenever
qemu_co_queue_restart_all was used outside coroutine context.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <20220427130830.150180-3-pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
qemu_co_queue_next is basically the same as qemu_co_enter_next but
without a QemuLockable argument. That's perfectly fine, but only
as long as the function is marked coroutine_fn. If used outside
coroutine context, qemu_co_queue_wait will attempt to take the lock
and that is just broken: if you are calling qemu_co_queue_next outside
coroutine context, the lock is going to be a QemuMutex which cannot be
taken twice by the same thread.
The patch adds the marker and reimplements qemu_co_queue_next in terms of
qemu_co_enter_next_impl, to remove duplicated code and to clarify that the
latter also works in coroutine context.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <20220427130830.150180-2-pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Handle HostMemoryBackend creation and setting of ms->ram entirely in
machine_run_board_init.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20220414165300.555321-5-pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Make -boot syntactic sugar for a compound property "-machine boot.{order,menu,...}".
machine_boot_parse is replaced by the setter for the property.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20220414165300.555321-3-pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
As part of converting -boot to a property with a QAPI type, define
the struct and use it throughout QEMU to access boot configuration.
machine_boot_parse takes care of doing the QemuOpts->QAPI conversion by
hand, for now.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20220414165300.555321-2-pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
It's true that these functions currently affect the batch size in which
coroutines are reused (i.e. moved from the global release pool to the
allocation pool of a specific thread), but this is a bug and will be
fixed in a separate patch.
In fact, the comment in the header file already just promises that it
influences the pool size, so reflect this in the name of the functions.
As a nice side effect, the shorter function name makes some line
wrapping unnecessary.
Cc: qemu-stable@nongnu.org
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <20220510151020.105528-2-kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
igd-passthrough-isa-bridge is only requested in xen_pt but was
implemented in pc_piix.c. This caused xen_pt to dependend on i386/pc
which is hereby resolved.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Acked-by: Anthony PERARD <anthony.perard@citrix.com>
Message-Id: <20220326165825.30794-2-shentey@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Cleaned up with scripts/clean-header-guards.pl.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20220506134911.2856099-5-armbru@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
We commonly define the header guard symbol without an explicit value.
Normalize the exceptions.
Done with scripts/clean-header-guards.pl.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20220506134911.2856099-4-armbru@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Leading underscores are ill-advised because such identifiers are
reserved. Trailing underscores are merely ugly. Strip both.
Our header guards commonly end in _H. Normalize the exceptions.
Macros should be ALL_CAPS. Normalize the exception.
Done with scripts/clean-header-guards.pl.
include/hw/xen/interface/ and tools/virtiofsd/ left alone, because
these were imported from Xen and libfuse respectively.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20220506134911.2856099-3-armbru@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Header guard symbols should match their file name to make guard
collisions less likely.
Cleaned up with scripts/clean-header-guards.pl, followed by some
renaming of new guard symbols picked by the script to better ones.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20220506134911.2856099-2-armbru@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
[Change to generated file ebpf/rss.bpf.skeleton.h backed out]
- Add new thread-pool-min/thread-pool-max parameters to control the thread pool
used for async I/O.
- Fix virtio-scsi IOThread 100% CPU consumption QEMU 7.0 regression.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEhpWov9P5fNqsNXdanKSrs4Grc8gFAmJ5DqgACgkQnKSrs4Gr
c8iAqAf/WEJzEso0Hu3UUYJi2lAXpLxWPjoNBlPdQlKIJ/I0zQIF0P7GeCifF+0l
iMjgBv0ofyAuV47gaTJlVrAR75+hJ/IXNDhnu3UuvNWfVOqvksgw6kuHkMo9A2hC
4tIHEU9J8jbQSSdQTaZR8Zj4FX1/zcxMBAXT3YO3De6zo78RatBTuNP4dsZzt8bI
Qs1a4A0p2ScNXK8EcF4QwAWfoxu9OPPzN52DBCNxcIcnn0SUab4NbDxzpRV4ZhDP
08WoafI5O+2Kb36QysJN01LqajHrClG/fozrPzBLq5aZUK3xewJGB1hEdGTLkkmz
NJNBg5Ldszwj4PDZ1dFU3/03aigb3g==
=t5eR
-----END PGP SIGNATURE-----
Merge tag 'block-pull-request' of https://gitlab.com/stefanha/qemu into staging
Pull request
- Add new thread-pool-min/thread-pool-max parameters to control the thread pool
used for async I/O.
- Fix virtio-scsi IOThread 100% CPU consumption QEMU 7.0 regression.
# -----BEGIN PGP SIGNATURE-----
#
# iQEzBAABCAAdFiEEhpWov9P5fNqsNXdanKSrs4Grc8gFAmJ5DqgACgkQnKSrs4Gr
# c8iAqAf/WEJzEso0Hu3UUYJi2lAXpLxWPjoNBlPdQlKIJ/I0zQIF0P7GeCifF+0l
# iMjgBv0ofyAuV47gaTJlVrAR75+hJ/IXNDhnu3UuvNWfVOqvksgw6kuHkMo9A2hC
# 4tIHEU9J8jbQSSdQTaZR8Zj4FX1/zcxMBAXT3YO3De6zo78RatBTuNP4dsZzt8bI
# Qs1a4A0p2ScNXK8EcF4QwAWfoxu9OPPzN52DBCNxcIcnn0SUab4NbDxzpRV4ZhDP
# 08WoafI5O+2Kb36QysJN01LqajHrClG/fozrPzBLq5aZUK3xewJGB1hEdGTLkkmz
# NJNBg5Ldszwj4PDZ1dFU3/03aigb3g==
# =t5eR
# -----END PGP SIGNATURE-----
# gpg: Signature made Mon 09 May 2022 05:52:56 AM PDT
# gpg: using RSA key 8695A8BFD3F97CDAAC35775A9CA4ABB381AB73C8
# gpg: Good signature from "Stefan Hajnoczi <stefanha@redhat.com>" [full]
# gpg: aka "Stefan Hajnoczi <stefanha@gmail.com>" [full]
* tag 'block-pull-request' of https://gitlab.com/stefanha/qemu:
virtio-scsi: move request-related items from .h to .c
virtio-scsi: clean up virtio_scsi_handle_cmd_vq()
virtio-scsi: clean up virtio_scsi_handle_ctrl_vq()
virtio-scsi: clean up virtio_scsi_handle_event_vq()
virtio-scsi: don't waste CPU polling the event virtqueue
virtio-scsi: fix ctrl and event handler functions in dataplane mode
util/event-loop-base: Introduce options to set the thread pool size
util/main-loop: Introduce the main loop into QOM
Introduce event-loop-base abstract class
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
There is no longer a need to expose the request and related APIs in
virtio-scsi.h since there are no callers outside virtio-scsi.c.
Note the block comment in VirtIOSCSIReq has been adjusted to meet the
coding style.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-id: 20220427143541.119567-7-stefanha@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
virtio_scsi_handle_cmd_vq() is only called from hw/scsi/virtio-scsi.c
now and its return value is no longer used. Remove the function
prototype from virtio-scsi.h and drop the return value.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-id: 20220427143541.119567-6-stefanha@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
virtio_scsi_handle_ctrl_vq() is only called from hw/scsi/virtio-scsi.c
now and its return value is no longer used. Remove the function
prototype from virtio-scsi.h and drop the return value.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-id: 20220427143541.119567-5-stefanha@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
virtio_scsi_handle_event_vq() is only called from hw/scsi/virtio-scsi.c
now and its return value is no longer used. Remove the function
prototype from virtio-scsi.h and drop the return value.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-id: 20220427143541.119567-4-stefanha@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
The virtio-scsi event virtqueue is not emptied by its handler function.
This is typical for rx virtqueues where the device uses buffers when
some event occurs (e.g. a packet is received, an error condition
happens, etc).
Polling non-empty virtqueues wastes CPU cycles. We are not waiting for
new buffers to become available, we are waiting for an event to occur,
so it's a misuse of CPU resources to poll for buffers.
Introduce the new virtio_queue_aio_attach_host_notifier_no_poll() API,
which is identical to virtio_queue_aio_attach_host_notifier() except
that it does not poll the virtqueue.
Before this patch the following command-line consumed 100% CPU in the
IOThread polling and calling virtio_scsi_handle_event():
$ qemu-system-x86_64 -M accel=kvm -m 1G -cpu host \
--object iothread,id=iothread0 \
--device virtio-scsi-pci,iothread=iothread0 \
--blockdev file,filename=test.img,aio=native,cache.direct=on,node-name=drive0 \
--device scsi-hd,drive=drive0
After this patch CPU is no longer wasted.
Reported-by: Nir Soffer <nsoffer@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Tested-by: Nir Soffer <nsoffer@redhat.com>
Message-id: 20220427143541.119567-3-stefanha@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
The thread pool regulates itself: when idle, it kills threads until
empty, when in demand, it creates new threads until full. This behaviour
doesn't play well with latency sensitive workloads where the price of
creating a new thread is too high. For example, when paired with qemu's
'-mlock', or using safety features like SafeStack, creating a new thread
has been measured take multiple milliseconds.
In order to mitigate this let's introduce a new 'EventLoopBase'
property to set the thread pool size. The threads will be created during
the pool's initialization or upon updating the property's value, remain
available during its lifetime regardless of demand, and destroyed upon
freeing it. A properly characterized workload will then be able to
configure the pool to avoid any latency spikes.
Signed-off-by: Nicolas Saenz Julienne <nsaenzju@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Acked-by: Markus Armbruster <armbru@redhat.com>
Message-id: 20220425075723.20019-4-nsaenzju@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
'event-loop-base' provides basic property handling for all 'AioContext'
based event loops. So let's define a new 'MainLoopClass' that inherits
from it. This will permit tweaking the main loop's properties through
qapi as well as through the command line using the '-object' keyword[1].
Only one instance of 'MainLoopClass' might be created at any time.
'EventLoopBaseClass' learns a new callback, 'can_be_deleted()' so as to
mark 'MainLoop' as non-deletable.
[1] For example:
-object main-loop,id=main-loop,aio-max-batch=<value>
Signed-off-by: Nicolas Saenz Julienne <nsaenzju@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Acked-by: Markus Armbruster <armbru@redhat.com>
Message-id: 20220425075723.20019-3-nsaenzju@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Introduce the 'event-loop-base' abstract class, it'll hold the
properties common to all event loops and provide the necessary hooks for
their creation and maintenance. Then have iothread inherit from it.
EventLoopBaseClass is defined as user creatable and provides a hook for
its children to attach themselves to the user creatable class 'complete'
function. It also provides an update_params() callback to propagate
property changes onto its children.
The new 'event-loop-base' class will live in the root directory. It is
built on its own using the 'link_whole' option (there are no direct
function dependencies between the class and its children, it all happens
trough 'constructor' magic). And also imposes new compilation
dependencies:
qom <- event-loop-base <- blockdev (iothread.c)
And in subsequent patches:
qom <- event-loop-base <- qemuutil (util/main-loop.c)
All this forced some amount of reordering in meson.build:
- Moved qom build definition before qemuutil. Doing it the other way
around (i.e. moving qemuutil after qom) isn't possible as a lot of
core libraries that live in between the two depend on it.
- Process the 'hw' subdir earlier, as it introduces files into the
'qom' source set.
No functional changes intended.
Signed-off-by: Nicolas Saenz Julienne <nsaenzju@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Acked-by: Markus Armbruster <armbru@redhat.com>
Message-id: 20220425075723.20019-2-nsaenzju@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
A global boolean variable "vga_interface_created"(declared in softmmu/globals.c)
has been used to track the creation of vga interface. If the vga flag is passed
in the command line "default_vga"(declared in softmmu/vl.c) variable is set to 0.
To warn user, the condition checks if vga_interface_created is false
and default_vga is equal to 0. If "-vga none" is passed, this patch will not warn the
user regarding the creation of VGA device.
The warning "A -vga option was passed but this
machine type does not use that option; no VGA device has been created"
is logged if vga flag is passed but no vga device is created.
This patch has been tested for x86_64, i386, sparc, sparc64 and arm boards.
Signed-off-by: Gautam Agrawal <gautamnagrawal@gmail.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/581
Message-Id: <20220501122505.29202-1-gautamnagrawal@gmail.com>
[thuth: Fix wrong warning with "-device" in some cases as reported by Paolo]
Signed-off-by: Thomas Huth <thuth@redhat.com>
Capstone should be superior to the old libopcode disassembler,
so we can drop the old file nowadays.
Message-Id: <20220505173619.488350-1-thuth@redhat.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Capstone should be superior to the old libopcode disassembler,
so we can drop the old file nowadays.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20220412165836.355850-4-thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Capstone should be superior to the old libopcode disassembler, so
we can drop the old file nowadays.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20220412165836.355850-3-thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Move the LASI device implementation from hw/hppa to hw/misc so that it is
located with all the other miscellaneous devices.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Acked-by: Helge Deller <deller@gmx.de>
Message-Id: <20220504092600.10048-43-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Move the DINO device implementation from hw/hppa to hw/pci-host so that it is
located with all the other PCI host bridges.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Acked-by: Helge Deller <deller@gmx.de>
Message-Id: <20220504092600.10048-23-mark.cave-ayland@ilande.co.uk>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
The pcspk device is the only user of the init_isa function, and the only
-soundhw option which does not create a new device (it hacks into the
PCSpkState by hand). Remove it, since it was deprecated.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
vhost-scsi and vhost-user-scsi are two devices of their own; it should
be possible to enable/disable them with --without-default-devices, not
--without-default-features. Compute their default value in Kconfig to
obtain the more intuitive behavior.
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Rename VFIOGuestIOMMU iommu field into iommu_mr. Then it becomes clearer
it is an IOMMU memory region.
no functional change intended
Signed-off-by: Yi Liu <yi.l.liu@intel.com>
Link: https://lore.kernel.org/r/20220502094223.36384-4-yi.l.liu@intel.com
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
In a subsequent patch, VFIO will need to recognize if
a memory region owner is a TPM CRB device. Hence VFIO
needs to use TPM_IS_CRB() even if CONFIG_TPM is unset. So
let's add a stub function.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Suggested-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Stefan Berger <stefanb@linnux.ibm.com>
Link: https://lore.kernel.org/r/20220506132510.1847942-2-eric.auger@redhat.com
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
When pulling or pushing an OS context from/to a CPU, we should
re-evaluate the state of the External interrupt signal. Otherwise, we
can end up catching the External interrupt exception in hypervisor
mode, which is unexpected.
The problem is best illustrated with the following scenario:
1. an External interrupt is raised while the guest is on the CPU.
2. before the guest can ack the External interrupt, an hypervisor
interrupt is raised, for example the Hypervisor Decrementer or
Hypervisor Virtualization interrupt. The hypervisor interrupt forces
the guest to exit while the External interrupt is still pending.
3. the hypervisor handles the hypervisor interrupt. At this point, the
External interrupt is still pending. So it's very likely to be
delivered while the hypervisor is running. That's unexpected and can
result in an infinite loop where the hypervisor catches the External
interrupt, looks for an interrupt in its hypervisor queue, doesn't
find any, exits the interrupt handler with the External interrupt
still raised, repeat...
The fix is simply to always lower the External interrupt signal when
pulling an OS context. It means it needs to be raised again when
re-pushing the OS context. Fortunately, it's already the case, as we
now always call xive_tctx_ipb_update(), which will raise the signal if
needed.
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Frederic Barrat <fbarrat@linux.ibm.com>
Message-Id: <20220429071620.177142-3-fbarrat@linux.ibm.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
This reverts commit b1c0734905. (We
wanted to do so once the 7.1 tree opens, which has happened. The issue
reported in https://gitlab.com/qemu-project/qemu/-/issues/945 should be
fixed by the preceding patches.)
Signed-off-by: Hanna Reitz <hreitz@redhat.com>
Message-Id: <20220427114057.36651-4-hreitz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This function is safe to call in an I/O context, and qcow2_do_open()
does so (invoked in an I/O context by qcow2_co_invalidate_cache()).
Signed-off-by: Hanna Reitz <hreitz@redhat.com>
Message-Id: <20220427114057.36651-2-hreitz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Capstone should be superior to the old libopcode disassembler,
so we can drop the old file nowadays.
Message-Id: <20220412165836.355850-2-thuth@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Swap half-words (16-bit) and words (32-bit) within a larger value.
Mirrors functions of the same names within include/qemu/bitops.h.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: David Hildenbrand <david@redhat.com>
Reviewed-by: David Miller <dmiller423@gmail.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Message-Id: <20220428094708.84835-5-david@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
The qemu_*block() functions are meant to be be used with sockets (the
win32 implementation expects SOCKET)
Over time, those functions where used with Win32 SOCKET or
file-descriptors interchangeably. But for portability, they must only be
used with socket-like file-descriptors. FDs can use
g_unix_set_fd_nonblocking() instead.
Rename the functions with "socket" in the name to prevent bad usages.
This is effectively reverting commit f9e8cacc55 ("oslib-posix:
rename socket_set_nonblock() to qemu_set_nonblock()").
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
The function isn't used outside of qio_channel_command_new_spawn(),
which is !win32-specific.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
GLib g_unix_open_pipe() is essentially like qemu_pipe(), available since
2.30.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
It is only used by block/file-posix.c, move it there.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Per ast1030_v7.pdf, AST1030 HACE engine is identical to AST2600's HACE
engine.
Signed-off-by: Steven Lee <steven_lee@aspeedtech.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The aspeed ast2600 accumulative mode is described in datasheet
ast2600v10.pdf section 25.6.4:
1. Allocating and initiating accumulative hash digest write buffer
with initial state.
* Since QEMU crypto/hash api doesn't provide the API to set initial
state of hash library, and the initial state is already set by
crypto library (gcrypt/glib/...), so skip this step.
2. Calculating accumulative hash digest.
(a) When receiving the last accumulative data, software need to add
padding message at the end of the accumulative data. Padding
message described in specific of MD5, SHA-1, SHA224, SHA256,
SHA512, SHA512/224, SHA512/256.
* Since the crypto library (gcrypt/glib) already pad the
padding message internally.
* This patch is to remove the padding message which fed byguest
machine driver.
Signed-off-by: Troy Lee <troy_lee@aspeedtech.com>
Signed-off-by: Steven Lee <steven_lee@aspeedtech.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220426021120.28255-3-steven_lee@aspeedtech.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Support HACE28: Hash HMAC Key Buffer Base Address Register.
Signed-off-by: Troy Lee <troy_lee@aspeedtech.com>
Signed-off-by: Steven Lee <steven_lee@aspeedtech.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220426021120.28255-2-steven_lee@aspeedtech.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The embedded core of AST1030 SoC is ARM Coretex M4.
It is hard to be integrated in the common Aspeed Soc framework.
We introduce a new ast1030 class with instance_init and realize
handlers.
Signed-off-by: Troy Lee <troy_lee@aspeedtech.com>
Signed-off-by: Jamin Lin <jamin_lin@aspeedtech.com>
Signed-off-by: Steven Lee <steven_lee@aspeedtech.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
[ clg: rename aspeed_ast10xx.c to aspeed_ast10x0.c to match zephyr ]
Message-Id: <20220401083850.15266-8-jamin_lin@aspeedtech.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Per ast1030_v07.pdf, AST1030 SOC doesn't have SCU300, the pclk divider
selection is defined in SCU310[11:8].
Add a get_apb_freq function and a class init handler for ast1030.
Signed-off-by: Troy Lee <troy_lee@aspeedtech.com>
Signed-off-by: Jamin Lin <jamin_lin@aspeedtech.com>
Signed-off-by: Steven Lee <steven_lee@aspeedtech.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220401083850.15266-7-jamin_lin@aspeedtech.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
ast1030 tmc(timer controller) is identical to ast2600 tmc.
Signed-off-by: Troy Lee <troy_lee@aspeedtech.com>
Signed-off-by: Jamin Lin <jamin_lin@aspeedtech.com>
Signed-off-by: Steven Lee <steven_lee@aspeedtech.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220401083850.15266-6-jamin_lin@aspeedtech.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
AST1030 wdt controller is similiar to AST2600's wdt, but it has extra
registers.
Introduce ast1030 object class and increse the number of regs(offset) of
ast1030 model.
Signed-off-by: Troy Lee <troy_lee@aspeedtech.com>
Signed-off-by: Jamin Lin <jamin_lin@aspeedtech.com>
Signed-off-by: Steven Lee <steven_lee@aspeedtech.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220401083850.15266-5-jamin_lin@aspeedtech.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Per ast2500_2520_datasheet_v1.8 and ast2600v11.pdf, the default value of
WDT00 and WDT04 is 0x014FB180 for ast2500/ast2600.
Add default_status and default_reload_value attributes for storing
counter status and reload value as they are different from ast2400.
Signed-off-by: Troy Lee <troy_lee@aspeedtech.com>
Signed-off-by: Jamin Lin <jamin_lin@aspeedtech.com>
Signed-off-by: Steven Lee <steven_lee@aspeedtech.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220401083850.15266-4-jamin_lin@aspeedtech.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Per ast1030_v7.pdf, AST1030 ADC engine is identical to AST2600's ADC.
Signed-off-by: Troy Lee <troy_lee@aspeedtech.com>
Signed-off-by: Jamin Lin <jamin_lin@aspeedtech.com>
Signed-off-by: Steven Lee <steven_lee@aspeedtech.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220401083850.15266-2-jamin_lin@aspeedtech.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Guest code (u-boot) pokes at this on boot. No functionality is required
for guest code to work correctly, but it helps to document the region
being read from.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220318092211.723938-1-joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
AST2600 clkin is always 25MHz, introduce clkin_25Mhz attribute
for aspeed_scu_get_clkin() to return the correct clkin for ast2600.
Signed-off-by: Steven Lee <steven_lee@aspeedtech.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220315075753.8591-3-steven_lee@aspeedtech.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
AST2600's HPLL register offset and bit definition are different from
AST2500. Add a hpll calculation function and an apb frequency calculation
function based on SCU200 register description in ast2600v11.pdf.
Signed-off-by: Steven Lee <steven_lee@aspeedtech.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
[ clg: checkpatch fixes ]
Message-Id: <20220315075753.8591-2-steven_lee@aspeedtech.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Create a platform bus to allow dynamic devices to be connected. This is
based on the ARM implementation.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@amd.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Message-Id: <20220427234146.1130752-4-alistair.francis@opensource.wdc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The ARM virt machine currently uses sysbus-fdt to create device tree
entries for dynamically created MMIO devices.
The RISC-V virt machine can also benefit from this, so move the code to
the core directory.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@amd.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Message-Id: <20220427234146.1130752-3-alistair.francis@opensource.wdc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Move the binary and device tree loading code to the machine done
notifier. This allows us to prepare for editing the device tree as part
of the notifier.
This is based on similar code in the ARM virt machine.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@amd.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Message-Id: <20220427234146.1130752-2-alistair.francis@opensource.wdc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
- share it between target/arm and target/riscv
Signed-off-by: Weiwei Li <liweiwei@iscas.ac.cn>
Signed-off-by: Junqiang Wang <wangjunqiang@iscas.ac.cn>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20220423023510.30794-6-liweiwei@iscas.ac.cn>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
* refactor to use tcg_constant where appropriate
* Advertise support for FEAT_TTL and FEAT_BBM level 2
* smmuv3: Cache event fault record
* smmuv3: Add space in guest error message
* smmuv3: Advertise support for SMMUv3.2-BBML2
-----BEGIN PGP SIGNATURE-----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=IPEn
-----END PGP SIGNATURE-----
Merge tag 'pull-target-arm-20220428' of https://git.linaro.org/people/pmaydell/qemu-arm into staging
target-arm queue:
* refactor to use tcg_constant where appropriate
* Advertise support for FEAT_TTL and FEAT_BBM level 2
* smmuv3: Cache event fault record
* smmuv3: Add space in guest error message
* smmuv3: Advertise support for SMMUv3.2-BBML2
# -----BEGIN PGP SIGNATURE-----
#
# iQJNBAABCAA3FiEE4aXFk81BneKOgxXPPCUl7RQ2DN4FAmJqpu4ZHHBldGVyLm1h
# eWRlbGxAbGluYXJvLm9yZwAKCRA8JSXtFDYM3pOQD/9G190+ntJm4Vndz0I6bCDP
# svDrWwsioOJ4q5Pah6517JACkwN5sx0adMGyAeRC3Kcbz5B2141vv9hJOnJmLB1D
# l6KbH8XZaftC0B8fXsPkaH6XEdBHGz6YbOZaLOTwmFqF9d18OFW4d8+CAvfldZRc
# +DYeolEhoL9eLTS16BlXPxb0LajQHhbN1Xdu3t8CGh31C52ZrG4h8cus6YMEDjfA
# rfBthh/2QvVFmDedIfX4QrlImCTs+bTaSkhUBmX6qakWII0QykItgQTEZ8IHEr8/
# QmG+xlkP1MmffyHU3F4inEVXpjCSzula4ycZpNVGsrTHYxLBzsTSD+EzicLHMZSt
# 64tQhLxPjAzC1MEHp7bJHyQXon7REWd6u1jPRlMWTGpZqbMMchBPjFrsxK3YPdvi
# a/8KIulXuX+GjzbOIHnpttIy+U0UrjTEyxjpk+Ay2iZ+U6+hA3i2ni++dzq9dYb6
# IiCl+o29r/7fNaWpG3b38kn9vpxjwAAw+qfwwSqyM+8/KMirgJ8rpEmUPei/h7fy
# vqpNlVxd1+Tzb3ljCXNRriZ05xo5I9LIb+dLAig1orENS7w3SzW/GnM+S7raOwQb
# u9mxNmbQJ1MhkjNC/6wzniBre6EBs31X2GIWeuiWe/js2YFPQC06b1WwIc/bYNUv
# anbECOS34mtxbExFfdlxUQ==
# =IPEn
# -----END PGP SIGNATURE-----
# gpg: Signature made Thu 28 Apr 2022 07:38:38 AM PDT
# gpg: using RSA key E1A5C593CD419DE28E8315CF3C2525ED14360CDE
# gpg: issuer "peter.maydell@linaro.org"
# gpg: Good signature from "Peter Maydell <peter.maydell@linaro.org>" [full]
# gpg: aka "Peter Maydell <pmaydell@gmail.com>" [full]
# gpg: aka "Peter Maydell <pmaydell@chiark.greenend.org.uk>" [full]
* tag 'pull-target-arm-20220428' of https://git.linaro.org/people/pmaydell/qemu-arm: (54 commits)
hw/arm/smmuv3: Advertise support for SMMUv3.2-BBML2
target/arm: Advertise support for FEAT_BBM level 2
target/arm: Advertise support for FEAT_TTL
hw/arm/smmuv3: Add space in guest error message
hw/arm/smmuv3: Cache event fault record
target/arm: Use field names for accessing DBGWCRn
target/arm: Disable cryptographic instructions when neon is disabled
target/arm: Use tcg_constant for vector descriptor
target/arm: Use tcg_constant for do_brk{2,3}
target/arm: Use tcg_constant for predicate descriptors
target/arm: Use tcg_constant in do_zzi_{sat, ool}, do_fp_imm
target/arm: Use tcg_constant in SUBR
target/arm: Use tcg_constant in LD1, ST1
target/arm: Use tcg_constant in WHILE
target/arm: Use tcg_constant in do_clast_scalar
target/arm: Use tcg_constant in {incr, wrap}_last_active
target/arm: Use tcg_constant in FCPY, CPY
target/arm: Use tcg_constant in SINCDEC, INCDEC
target/arm: Use tcg_constant for trans_INDEX_*
target/arm: Use tcg_constant in trans_CSEL
...
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
The Record bit in the Context Descriptor tells the SMMU to report fault
events to the event queue. Since we don't cache the Record bit at the
moment, access faults from a cached Context Descriptor are never
reported. Store the Record bit in the cached SMMUTransCfg.
Fixes: 9bde7f0674 ("hw/arm/smmuv3: Implement translate callback")
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20220427111543.124620-1-jean-philippe@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Like -set and -readconfig, it would not really be too hard to
extend -writeconfig to parsing mechanisms other than QemuOpts.
However, the uses of -writeconfig are substantially more
limited, as it is generally easier to write the configuration
by hand in the first place. In addition, -writeconfig does
not even try to detect cases where it prints incorrect
syntax (for example if values have a quote in them, since
qemu_config_parse does not support any kind of escaping.
Just remove it.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20220414145721.326866-1-pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
move sev firmware setup to separate function so it can be used from
other code paths. No functional change.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Tested-by: Xiaoyao Li <xiaoyao.li@intel.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <20220425135051.551037-3-kraxel@redhat.com>
Add possibility to change addresses where VNC server listens for new
connections. Prior to 6.0 this functionality was available through
'change' qmp command which was deleted.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@openvz.org>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Message-Id: <20220401143936.356460-3-vsementsov@openvz.org>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
- Paolo Bonzini: thread-safety improvements to NBD client
- Vladimir Sementsov-Ogievsky: finer-grained selection of bitmaps during
nbd-export
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEccLMIrHEYCkn0vOqp6FrSiUnQ2oFAmJoUhAACgkQp6FrSiUn
Q2qnpgf/YCuONdwAndjEo7he5c1BfB/F2sujQJJ00CebUqnz5OFKQ85RwLC8DCGB
rXnxqC/NF4yyYM+6uYWDpggDd0bJVKbfG7NE/AZsEZrK+n9xMkvGLRwGqMugUii+
Px4Ba98++0giqGoAI8pU/wQZNh1I6uGabv/DPRTpwzBjbfAcATqV09OzaGiK3SRC
Zm/55zmXm1zM4XSUtUzN1gILPG09P+51m6NVkANZbzps9e2PtfFy8EsWc5+YhuBM
5K7sN+5g8GpRhz6j8RkrhrbNpvg3bGvgRJRMcW7Bo8KVUdvT1Jng6xs8CIRv39AF
jDJwGe+cq5p5PNuyqOrVSA/ynBZxBw==
=I1yM
-----END PGP SIGNATURE-----
Merge tag 'pull-nbd-2022-04-26' of https://repo.or.cz/qemu/ericb into staging
nbd patches for 2022-04-26
- Paolo Bonzini: thread-safety improvements to NBD client
- Vladimir Sementsov-Ogievsky: finer-grained selection of bitmaps during
nbd-export
# -----BEGIN PGP SIGNATURE-----
#
# iQEzBAABCAAdFiEEccLMIrHEYCkn0vOqp6FrSiUnQ2oFAmJoUhAACgkQp6FrSiUn
# Q2qnpgf/YCuONdwAndjEo7he5c1BfB/F2sujQJJ00CebUqnz5OFKQ85RwLC8DCGB
# rXnxqC/NF4yyYM+6uYWDpggDd0bJVKbfG7NE/AZsEZrK+n9xMkvGLRwGqMugUii+
# Px4Ba98++0giqGoAI8pU/wQZNh1I6uGabv/DPRTpwzBjbfAcATqV09OzaGiK3SRC
# Zm/55zmXm1zM4XSUtUzN1gILPG09P+51m6NVkANZbzps9e2PtfFy8EsWc5+YhuBM
# 5K7sN+5g8GpRhz6j8RkrhrbNpvg3bGvgRJRMcW7Bo8KVUdvT1Jng6xs8CIRv39AF
# jDJwGe+cq5p5PNuyqOrVSA/ynBZxBw==
# =I1yM
# -----END PGP SIGNATURE-----
# gpg: Signature made Tue 26 Apr 2022 01:12:00 PM PDT
# gpg: using RSA key 71C2CC22B1C4602927D2F3AAA7A16B4A2527436A
# gpg: Good signature from "Eric Blake <eblake@redhat.com>" [full]
# gpg: aka "Eric Blake (Free Software Programmer) <ebb9@byu.net>" [full]
# gpg: aka "[jpeg image of size 6874]" [full]
* tag 'pull-nbd-2022-04-26' of https://repo.or.cz/qemu/ericb:
nbd: document what is protected by the CoMutexes
nbd: take receive_mutex when reading requests[].receiving
nbd: move s->state under requests_lock
nbd: code motion and function renaming
nbd: use a QemuMutex to synchronize yanking, reconnection and coroutines
nbd: keep send_mutex/free_sema handling outside nbd_co_do_establish_connection
nbd: remove peppering of nbd_client_connected
nbd: mark more coroutine_fns
nbd: safeguard against waking up invalid coroutine
iotests/223: check new possibility of exporting bitmaps by node/name
qapi: nbd-export: allow select bitmaps by node/name pair
qapi: rename BlockDirtyBitmapMergeSource to BlockDirtyBitmapOrStr
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Rename the type to be reused. Old name is "what is it for". To be
natively reused for other needs, let's name it exactly "what is it".
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@openvz.org>
Message-Id: <20220314213226.362217-2-v.sementsov-og@mail.ru>
[eblake: Adjust S-o-b to Vladimir's new email, with permission]
Reviewed-by: Eric Blake <eblake@redhat.com>
Acked-by: John Snow <jsnow@redhat.com>
Signed-off-by: Eric Blake <eblake@redhat.com>
Implement nios2 Vectored Interrupt Controller (VIC).
VIC is connected to EIC. It needs to update rha, ril, rrs and rnmi
fields on Nios2CPU before raising an IRQ.
For that purpose, VIC has a "cpu" property which should refer to the
nios2 cpu and set by the board that connects VIC.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Amir Gonnen <amir.gonnen@neuroblade.ai>
Message-Id: <20220303153906.2024748-5-amir.gonnen@neuroblade.ai>
[rth: Split out nios2_vic.h]
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20220421151735.31996-60-richard.henderson@linaro.org>
Users requiring FIPS support must build QEMU with either the libgcrypt
or gnutls libraries as the crytography backend.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Add support for the TCG GICv4 to the virt board. For the board,
the GICv4 is very similar to the GICv3, with the only difference
being the size of the redistributor frame. The changes here are thus:
* calculating virt_redist_capacity correctly for GICv4
* changing various places which were "if GICv3" to be "if not GICv2"
* the commandline option handling
Note that using GICv4 reduces the maximum possible number of CPUs on
the virt board from 512 to 317, because we can now only fit half as
many redistributors into the redistributor regions we have defined.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220408141550.1271295-42-peter.maydell@linaro.org
In several places in virt.c we calculate the number of redistributors that
fit in a region of our memory map, which is the size of the region
divided by the size of a single redistributor frame. For GICv4, the
redistributor frame is a different size from that for GICv3. Abstract
out the calculation of redistributor region capacity so that we have
one place we need to change to handle GICv4 rather than several.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220408141550.1271295-41-peter.maydell@linaro.org
The CPU interface changes to support vLPIs are fairly minor:
in the parts of the code that currently look at the list registers
to determine the highest priority pending virtual interrupt, we
must also look at the highest priority pending vLPI. To do this
we change hppvi_index() to check the vLPI and return a special-case
value if that is the right virtual interrupt to take. The callsites
(which handle HPPIR and IAR registers and the "raise vIRQ and vFIQ
lines" code) then have to handle this special-case value.
This commit includes two interfaces with the as-yet-unwritten
redistributor code:
* the new GICv3CPUState::hppvlpi will be set by the redistributor
(in the same way as the existing hpplpi does for physical LPIs)
* when the CPU interface acknowledges a vLPI it needs to set it
to non-pending; the new gicv3_redist_vlpi_pending() function
(which matches the existing gicv3_redist_lpi_pending() used
for physical LPIs) is a stub that will be filled in later
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220408141550.1271295-26-peter.maydell@linaro.org
Implement the new GICv4 redistributor registers: GICR_VPROPBASER
and GICR_VPENDBASER; for the moment we implement these as simple
reads-as-written stubs, together with the necessary migration
and reset handling.
We don't put ID-register checks on the handling of these registers,
because they are all in the only-in-v4 extra register frames, so
they're not accessible in a GICv3.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220408141550.1271295-24-peter.maydell@linaro.org
The GICv4 extends the redistributor register map -- where GICv3
had two 64KB frames per CPU, GICv4 has four frames. Add support
for the extra frame by using a new gicv3_redist_size() function
in the places in the GIC implementation which currently use
a fixed constant size for the redistributor register block.
(Until we implement the extra registers they will RAZ/WI.)
Any board that wants to use a GICv4 will need to also adjust
to handle the different sized redistributor register block;
that will be done separately.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220408141550.1271295-23-peter.maydell@linaro.org
Implement the GICv4 VMOVP command, which updates an entry in the vPE
table to change its rdbase field. This command is unique in the ITS
command set because its effects must be propagated to all the other
ITSes connected to the same GIC as the ITS which executes the VMOVP
command.
The GICv4 spec allows two implementation choices for handling the
propagation to other ITSes:
* If GITS_TYPER.VMOVP is 1, the guest only needs to issue the command
on one ITS, and the implementation handles the propagation to
all ITSes
* If GITS_TYPER.VMOVP is 0, the guest must issue the command on
every ITS, and arrange for the ITSes to synchronize the updates
with each other by setting ITSList and Sequence Number fields
in the command packets
We choose the GITS_TYPER.VMOVP = 1 approach, and synchronously
execute the update on every ITS.
For GICv4.1 this command has extra fields in the command packet and
additional behaviour. We define the 4.1-only fields with the FIELD
macro, but only implement the GICv4.0 version of the command.
Note that we don't update the reported GITS_TYPER value here;
we'll do that later in a commit which updates all the reported
feature bit and ID register values for GICv4.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220408141550.1271295-17-peter.maydell@linaro.org
[PMM: Moved gicv3_foreach_its() to arm_gicv3_its_common.h,
for consistency with gicv3_add_its()]
These structures are required to produce 32-bit guest Windows Complete
Memory Dump. Add 32-bit Windows dump header, CPU context and physical
memory descriptor structures along with corresponding definitions.
Signed-off-by: Viktor Prutyanov <viktor.prutyanov@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20220406171558.199263-4-viktor.prutyanov@redhat.com>
Context structure in 64-bit Windows differs from 32-bit one and it
should be reflected in its name.
Signed-off-by: Viktor Prutyanov <viktor.prutyanov@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20220406171558.199263-2-viktor.prutyanov@redhat.com>
Offset calculations are easy enough to get wrong. Let's add a few
variables to make moving around elf headers and data sections easier.
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20220330123603.107120-6-frankja@linux.ibm.com>
Let's move from a boolean to a int variable which will later enable us
to store the number of sections that are in the dump file.
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20220330123603.107120-4-frankja@linux.ibm.com>
There's no need to have phdr_num and sh_info at the same time. We can
make phdr_num 32 bit and set PN_XNUM when we write the header if
phdr_num >= PN_XNUM.
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20220407094824.5074-1-frankja@linux.ibm.com>
The GICv4 ITS VMOVP command's semantics require it to perform the
operation on every ITS connected to the same GIC that the ITS that
received the command is attached to. This means that the GIC object
needs to keep a pointer to every ITS that is connected to it
(previously it was sufficient for the ITS to have a pointer to its
GIC).
Add a glib ptrarray to the GICv3 object which holds pointers to every
connected ITS, and make the ITS add itself to the array for the GIC
it is connected to when it is realized.
Note that currently all QEMU machine types with an ITS have exactly
one ITS in the system, so typically the length of this ptrarray will
be 1. Multiple ITSes are typically used to improve performance on
real hardware, so we wouldn't need to have more than one unless we
were modelling a real machine type that had multile ITSes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
[PMM: Moved gicv3_add_its() to arm_gicv3_its_common.h to avoid
compilation error building the KVM ITS]
Message-id: 20220408141550.1271295-16-peter.maydell@linaro.org
The GICv4 defines a new in-guest-memory table for the ITS: this is
the vPE table. Implement the new GITS_BASER2 register which the
guest uses to tell the ITS where the vPE table is located, including
the decode of the register fields into the TableDesc structure which
we do for the GITS_BASER<n> when the guest enables the ITS.
We guard provision of the new register with the its_feature_virtual()
function, which does a check of the GITS_TYPER.Virtual bit which
indicates presence of ITS support for virtual LPIs. Since this bit
is currently always zero, GICv4-specific features will not be
accessible to the guest yet.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220408141550.1271295-8-peter.maydell@linaro.org
The current riscv_load_fdt() forces fdt_load_addr to be placed at a dram address within 3GB,
but not all platforms have dram_base within 3GB.
This patch adds an exception for dram base not within 3GB,
which will place fdt at dram_end align 16MB.
riscv_setup_rom_reset_vec() also needs to be modified
Signed-off-by: Dylan Jhong <dylan@andestech.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20220419115945.37945-1-dylan@andestech.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This is now used by RISC-V as well. Update the comments.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20220421003324.1134983-7-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
RISC-V privilege spec defines that mtime is exposed as a memory-mapped
machine-mode read-write register. However, as QEMU uses host monotonic
timer as timer source, this makes mtime to be read-only in RISC-V
ACLINT.
This patch makes mtime to be writable by recording the time delta value
between the mtime value to be written and the timer value at the time
mtime is written. Time delta value is then added back whenever the timer
value is retrieved.
Signed-off-by: Frank Chang <frank.chang@sifive.com>
Reviewed-by: Jim Shu <jim.shu@sifive.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20220420080901.14655-4-frank.chang@sifive.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Adds the SPI_HOST device model for ibex. The device specification is as per
[1]. The model has been tested on opentitan with spi_host unit tests
written for TockOS.
[1] https://docs.opentitan.org/hw/ip/spi_host/doc/
Signed-off-by: Wilfred Mallawa <wilfred.mallawa@wdc.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20220303045426.511588-1-alistair.francis@opensource.wdc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
* hw/arm/virt: Check for attempt to use TrustZone with KVM or HVF
* versal: Add the Cortex-R5s in the Real-Time Processing Unit (RPU) subsystem
* versal: model enough of the Clock/Reset Low-power domain (CRL) to allow control of the Cortex-R5s
* xlnx-zynqmp: Connect 4 TTC timers
* exynos4210: Refactor GIC/combiner code to stop using qemu_split_irq
* realview: replace 'qemu_split_irq' with 'TYPE_SPLIT_IRQ'
* stellaris: replace 'qemu_split_irq' with 'TYPE_SPLIT_IRQ'
* hw/core/irq: remove unused 'qemu_irq_split' function
* npcm7xx: use symbolic constants for PWRON STRAP bit fields
* virt: document impact of gic-version on max CPUs
-----BEGIN PGP SIGNATURE-----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=Rke9
-----END PGP SIGNATURE-----
Merge tag 'pull-target-arm-20220421' of https://git.linaro.org/people/pmaydell/qemu-arm into staging
target-arm queue:
* hw/arm/virt: Check for attempt to use TrustZone with KVM or HVF
* versal: Add the Cortex-R5s in the Real-Time Processing Unit (RPU) subsystem
* versal: model enough of the Clock/Reset Low-power domain (CRL) to allow control of the Cortex-R5s
* xlnx-zynqmp: Connect 4 TTC timers
* exynos4210: Refactor GIC/combiner code to stop using qemu_split_irq
* realview: replace 'qemu_split_irq' with 'TYPE_SPLIT_IRQ'
* stellaris: replace 'qemu_split_irq' with 'TYPE_SPLIT_IRQ'
* hw/core/irq: remove unused 'qemu_irq_split' function
* npcm7xx: use symbolic constants for PWRON STRAP bit fields
* virt: document impact of gic-version on max CPUs
# -----BEGIN PGP SIGNATURE-----
#
# iQJNBAABCAA3FiEE4aXFk81BneKOgxXPPCUl7RQ2DN4FAmJhPSUZHHBldGVyLm1h
# eWRlbGxAbGluYXJvLm9yZwAKCRA8JSXtFDYM3hAsD/4qzZK6LFL4kFH6E4z3tWIn
# ErHrfPGUt/SEfHLP+stQP/loFgkR1SNzcrIZ/HiDCB/W+IqQKuP+tHin2lMhO1tR
# KM6suUO1In2hoxfzimVta4F4GVN8ifY69qUYhaRxcBYSUpRXDNFJGsRIeT5JeUMd
# SArZUifRs7JUo25rIkg5Y+YZE37dmiA5gcuswtoLPa/UlDVqRxihLnItySmeutsc
# /Y8d/iym/ydlhvtL1OUt1KKYeg4ykrPzJCfvopsT2xgkwwB0PYci8//fa5IrRVlp
# Uw6yDssZrDIcXfVz88rdriILaszicCv8lOhTH6I74oXCatiyvi4BEzW8uGqVS8wt
# ff+AaKvGqb5t4GKKhCdpL2NzDwKBGWZHuruACs9IfvMkz62HE12Vr99qAKdQ3s93
# QnFIyUKg90mGkvKy8336zX3hnWjPH8wTASOXbNrgnt6GVLkqwy9ibug5kS+n77eJ
# BnkE5p3OfMVJ5a4o+iZbbDJKfzhNUHDSMIBbG1jRNzax1RgxOBtHFSqP5jmbpm+S
# agyr8h+Md0Tx1dwZKxdCGyvcbSZiG2WxRnci3dyT4MqYY1t1GEpOfcs1EN+CYKwG
# iuezZzJopjOFGaXQaB3OvbvCKxuroHKG61SmDmx+5OkfAxhrqe4ulwYij4jhsyhH
# t8zGzDOKLakv3li90xCX/w==
# =Rke9
# -----END PGP SIGNATURE-----
# gpg: Signature made Thu 21 Apr 2022 04:16:53 AM PDT
# gpg: using RSA key E1A5C593CD419DE28E8315CF3C2525ED14360CDE
# gpg: issuer "peter.maydell@linaro.org"
# gpg: Good signature from "Peter Maydell <peter.maydell@linaro.org>" [full]
# gpg: aka "Peter Maydell <pmaydell@gmail.com>" [full]
# gpg: aka "Peter Maydell <pmaydell@chiark.greenend.org.uk>" [full]
* tag 'pull-target-arm-20220421' of https://git.linaro.org/people/pmaydell/qemu-arm: (31 commits)
hw/arm: Use bit fields for NPCM7XX PWRON STRAPs
hw/misc: Add PWRON STRAP bit fields in GCR module
hw/arm/virt: impact of gic-version on max CPUs
hw/core/irq: remove unused 'qemu_irq_split' function
hw/arm/stellaris: replace 'qemu_split_irq' with 'TYPE_SPLIT_IRQ'
hw/arm/realview: replace 'qemu_split_irq' with 'TYPE_SPLIT_IRQ'
hw/arm/exynos4210: Drop Exynos4210Irq struct
hw/arm/exynos4210: Put combiners into state struct
hw/arm/exynos4210: Fold combiner splits into exynos4210_init_board_irqs()
hw/arm/exynos4210: Don't connect multiple lines to external GIC inputs
hw/arm/exynos4210: Connect MCT_G0 and MCT_G1 to both combiners
hw/arm/exynos4210: Fill in irq_table[] for internal-combiner-only IRQ lines
hw/arm/exynos4210: Use TYPE_SPLIT_IRQ in exynos4210_init_board_irqs()
hw/arm/exynos4210: Delete unused macro definitions
hw/arm/exynos4210: Move exynos4210_combiner_get_gpioin() into exynos4210.c
hw/arm/exynos4210: Drop ext_gic_irq[] from Exynos4210Irq struct
hw/arm/exynos4210: Put external GIC into state struct
hw/arm/exynos4210: Move exynos4210_init_board_irqs() into exynos4210.c
hw/arm/exynos4210: Fix code style nit in combiner_grp_to_gic_id[]
hw/arm/exynos4210: Coalesce board_irqs and irq_table
...
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Simplify the function to only return the directory path. Callers are
adjusted to use the GLib function to build paths, g_build_filename().
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Message-Id: <20220420132624.2439741-39-marcandre.lureau@redhat.com>
The function is specific to qemu-ga, no need to share it in QEMU.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Konstantin Kostiuk <kkostiuk@redhat.com>
Message-Id: <20220420132624.2439741-32-marcandre.lureau@redhat.com>
Since it depends on monitor code, and error_vprintf_unless_qmp() is
already there.
This will help to move error-report in a common subproject.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Message-Id: <20220420132624.2439741-31-marcandre.lureau@redhat.com>
Simplify a bit pre-compiler conditions.
For TSAN, QEMU already has CONFIG_TSAN, but it is only set when the
fiber API is present. (I wonder whether supporting TSAN without the
fiber API is really relevant)
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Message-Id: <20220420132624.2439741-27-marcandre.lureau@redhat.com>
Move them where they belong, since the functions are implemented in block-qdict.c.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Message-Id: <20220420132624.2439741-25-marcandre.lureau@redhat.com>
Do not require the whole option machinery to handle keyval, as it is
used by QAPI alone, without the option API. And match the associated
unit name.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Message-Id: <20220420132624.2439741-24-marcandre.lureau@redhat.com>
Move QEMU-specific code to util/osdep.c, so cutils can become a common
subproject.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Message-Id: <20220420132624.2439741-22-marcandre.lureau@redhat.com>
The implementation depends on the OS. (and longer-term goal is to move
cutils to a common subproject)
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Message-Id: <20220420132624.2439741-21-marcandre.lureau@redhat.com>
G_NORETURN was introduced in glib 2.68, fallback to G_GNUC_NORETURN in
glib-compat.
Note that this attribute must be placed before the function declaration
(bringing a bit of consistency in qemu codebase usage).
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Warner Losh <imp@bsdimp.com>
Message-Id: <20220420132624.2439741-20-marcandre.lureau@redhat.com>
Move the macro and declaration so it can use glib in the following
patch (it already depends on glib anyway for !optimize)
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Message-Id: <20220420132624.2439741-19-marcandre.lureau@redhat.com>
Move qemu_main() declaration to a new header.
Simplify main.c since both cocoa & sdl cannot be enabled together.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Akihiko Odaki <akihiko.odaki@gmail.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Message-Id: <20220420132624.2439741-5-marcandre.lureau@redhat.com>
Similar to the Aspeed code in include/misc/aspeed_scu.h, we define
the PWRON STRAP fields in their corresponding module for NPCM7XX.
Signed-off-by: Hao Wu <wuhaotsh@google.com>
Reviewed-by: Patrick Venture <venture@google.com>
Message-id: 20220411165842.3912945-2-wuhaotsh@google.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
