Dell Equallogic iSCSI SANs have a very unusual advertised geometry:
$ iscsi-inq -e 1 -c $((0xb0)) iscsi://XXX/0
wsnz:0
maximum compare and write length:1
optimal transfer length granularity:0
maximum transfer length:0
optimal transfer length:0
maximum prefetch xdread xdwrite transfer length:0
maximum unmap lba count:30720
maximum unmap block descriptor count:2
optimal unmap granularity:30720
ugavalid:1
unmap granularity alignment:0
maximum write same length:30720
which says that both the maximum and the optimal discard size
is 15M. It is not immediately apparent if the device allows
discard requests not aligned to the optimal size, nor if it
allows discards at a finer granularity than the optimal size.
I tried to find details in the SCSI Commands Reference Manual
Rev. A on what valid values of maximum and optimal sizes are
permitted, but while that document mentions a "Block Limits
VPD Page", I couldn't actually find documentation of that page
or what values it would have, or if a SCSI device has an
advertisement of its minimal unmap granularity. So it is not
obvious to me whether the Dell Equallogic device is compliance
with the SCSI specification.
Fortunately, it is easy enough to support non-power-of-2 sizing,
even if it means we are less efficient than truly possible when
targetting that device (for example, it means that we refuse to
unmap anything that is not a multiple of 15M and aligned to a
15M boundary, even if the device truly does support a smaller
granularity where unmapping actually works).
Reported-by: Peter Lieven <pl@kamp.de>
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <1469129688-22848-5-git-send-email-eblake@redhat.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Now that all drivers have a byte-based .bdrv_co_pdiscard(), we
no longer need to worry about the sector-based version. We can
also relax our minimum alignment to 1 for drivers that support it.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1468624988-423-18-git-send-email-eblake@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
There's enough drivers with a sector-based callback that it will
be easier to switch one at a time. This patch adds a byte-based
callback, and then after all drivers are swapped, we'll drop the
sector-based callback.
[checkpatch doesn't like the space after coroutine_fn in
block_int.h, but it's consistent with the rest of the file]
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1468624988-423-10-git-send-email-eblake@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Another step towards byte-based interfaces everywhere. Replace
the sector-based driver callback .bdrv_aio_discard() with a new
byte-based .bdrv_aio_pdiscard(). Only raw-posix and RBD drivers
are affected, so it was not worth splitting into multiple patches.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1468624988-423-9-git-send-email-eblake@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Underlying HBitmap operates even with uint64_t. Thus this change is safe.
This would be useful f.e. to mark entire bitmap dirty in one call.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Message-id: 1468503209-19498-2-git-send-email-den@openvz.org
CC: Stefan Hajnoczi <stefanha@redhat.com>
CC: Kevin Wolf <kwolf@redhat.com>
CC: Max Reitz <mreitz@redhat.com>
CC: Jeff Cody <jcody@redhat.com>
Signed-off-by: Jeff Cody <jcody@redhat.com>
Some guests (win2008 server for example) do a lot of unnecessary
flushing when underlying media has not changed. This adds additional
overhead on host when calling fsync/fdatasync.
This change introduces a write generation scheme in BlockDriverState.
Current write generation is checked against last flushed generation to
avoid unnessesary flushes.
The problem with excessive flushing was found by a performance test
which does parallel directory tree creation (from 2 processes).
Results improved from 0.424 loops/sec to 0.432 loops/sec.
Each loop creates 10^3 directories with 10 files in each.
This affected some blkdebug testcases that were expecting error logs from
failure-injected flushes which are now skipped entirely
(tests 026 071 089).
This also affects the performance of block jobs and thus BLOCK_JOB_READY
events for driver-mirror and active block-commit commands now arrives
faster, before QMP send successfully returns to caller (tests 141 144).
Signed-off-by: Evgeny Yakovlev <eyakovlev@virtuozzo.com>
Signed-off-by: Denis V. Lunev <den@openvz.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-id: 1468870792-7411-5-git-send-email-den@openvz.org
CC: Kevin Wolf <kwolf@redhat.com>
CC: Max Reitz <mreitz@redhat.com>
CC: Stefan Hajnoczi <stefanha@redhat.com>
CC: Fam Zheng <famz@redhat.com>
CC: John Snow <jsnow@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
This patch adds a new optional 'job-id' parameter to 'block-commit',
allowing the user to specify the ID of the block job to be created.
Signed-off-by: Alberto Garcia <berto@igalia.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This patch adds a new optional 'job-id' parameter to 'block-stream',
allowing the user to specify the ID of the block job to be created.
The HMP 'block_stream' command remains unchanged.
Signed-off-by: Alberto Garcia <berto@igalia.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This patch adds a new optional 'job-id' parameter to 'blockdev-backup'
and 'drive-backup', allowing the user to specify the ID of the block
job to be created.
The HMP 'drive_backup' command remains unchanged.
Signed-off-by: Alberto Garcia <berto@igalia.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This patch adds a new optional 'job-id' parameter to 'blockdev-mirror'
and 'drive-mirror', allowing the user to specify the ID of the block
job to be created.
The HMP 'drive_mirror' command remains unchanged.
Signed-off-by: Alberto Garcia <berto@igalia.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
'stream-start' has a parameter called 'backing-file', which is the
string to be written to bs->backing when the job finishes.
In the stream_start() implementation it is called 'backing_file_str',
but it the prototype in the header file it is called 'base_id'.
This patch fixes it so the name is the same in both cases and is
consistent with other cases (like commit_start()).
Signed-off-by: Alberto Garcia <berto@igalia.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This is the final patch for converting the common I/O path to take
a BdrvChild parameter instead of BlockDriverState.
The completion of this conversion means that all users that perform I/O
on an image need to actually hold a reference (in the form of BdrvChild,
possible as part of a BlockBackend) to that image. This also protects
against inconsistent use of BlockBackend vs. BlockDriverState functions
because direct use of a BlockDriverState isn't possible any more and
blk->root is private for block-backends.c.
In addition, we can now distinguish different users in the I/O path,
and the future op blockers work is going to add assertions based on
permissions stored in BdrvChild.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
Using int for values that are only used as booleans is confusing.
While at it, rearrange a couple of members so that all the bools
are contiguous.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
It makes more sense to have ALL block size limit constraints
in the same struct. Improve the documentation while at it.
Simplify a couple of conditionals, now that we have audited and
documented that request_alignment is always non-zero.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Sector-based limits are awkward to think about; in our on-going
quest to move to byte-based interfaces, convert max_discard and
discard_alignment. Rename them, using 'pdiscard' as an aid to
track which remaining discard interfaces need conversion, and so
that the compiler will help us catch the change in semantics
across any rebased code. The BlockLimits type is now completely
byte-based; and in iscsi.c, sector_limits_lun2qemu() is no
longer needed.
pdiscard_alignment is made unsigned (we use power-of-2 alignments
as bitmasks, where unsigned is easier to think about) while
leaving max_pdiscard signed (since we still have an 'int'
interface); this is comparable to what commit cf081fc did for
write zeroes limits. We may later want to make everything an
unsigned 64-bit limit - but that requires a bigger code audit.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Improve the documentation of the write zeroes limits, to mention
additional constraints that drivers should observe. Worth squashing
into commit cf081fca, if that hadn't been pushed already :)
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Sector-based limits are awkward to think about; in our on-going
quest to move to byte-based interfaces, convert max_transfer_length
and opt_transfer_length. Rename them (dropping the _length suffix)
so that the compiler will help us catch the change in semantics
across any rebased code, and improve the documentation. Use unsigned
values, so that we don't have to worry about negative values and
so that bit-twiddling is easier; however, we are still constrained
by 2^31 of signed int in most APIs.
When a value comes from an external source (iscsi and raw-posix),
sanitize the results to ensure that opt_transfer is a power of 2.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
It's possible that an AioContext notifier user was close to finishing
when .detach_aio_context() or .attached_aio_context() is called. In
that case they may call bdrv_remove_aio_context_notifier() during the
callback.
Use safe iteration to avoid crashing when the notifier list is modified
during iteration. We must not only handle the case where the current
aio notifier is removed during a callback but also the one where any
other aio notifier is removed.
The next patch adds an AioContext notifier for block jobs and they
really could be terminating just as .detach_aio_context() is invoked.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Message-id: 1466096189-6477-6-git-send-email-stefanha@redhat.com
Currently, we are trying to move the backing BDS from the source to the
target in bdrv_replace_in_backing_chain() which is called from
mirror_exit(). However, mirror_complete() already tries to open the
target's backing chain with a call to bdrv_open_backing_file().
First, we should only set the target's backing BDS once. Second, the
mirroring block job has a better idea of what to set it to than the
generic code in bdrv_replace_in_backing_chain() (in fact, the latter's
conditions on when to move the backing BDS from source to target are not
really correct).
Therefore, remove that code from bdrv_replace_in_backing_chain() and
leave it to mirror_complete().
Depending on what kind of mirroring is performed, we furthermore want to
use different strategies to open the target's backing chain:
- If blockdev-mirror is used, we can assume the user made sure that the
target already has the correct backing chain. In particular, we should
not try to open a backing file if the target does not have any yet.
- If drive-mirror with mode=absolute-paths is used, we can and should
reuse the already existing chain of nodes that the source BDS is in.
In case of sync=full, no backing BDS is required; with sync=top, we
just link the source's backing BDS to the target, and with sync=none,
we use the source BDS as the target's backing BDS.
We should not try to open these backing files anew because this would
lead to two BDSs existing per physical file in the backing chain, and
we would like to avoid such concurrent access.
- If drive-mirror with mode=existing is used, we have to use the
information provided in the physical image file which means opening
the target's backing chain completely anew, just as it has been done
already.
If the target's backing chain shares images with the source, this may
lead to multiple BDSs per physical image file. But since we cannot
reliably ascertain this case, there is nothing we can do about it.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Message-id: 20160610185750.30956-3-mreitz@redhat.com
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
It is always true for open images now.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
This allows drivers to share code between normal I/O and vmstate
accesses.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
This brings it in line with .bdrv_save_vmstate().
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Now that all drivers have been converted to a byte interface,
we no longer need a sector interface.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Update bdrv_co_do_write_zeroes() to be byte-based, and select
between the new byte-based bdrv_co_pwrite_zeroes() or the old
bdrv_co_write_zeroes(). The next patches will convert drivers,
then remove the old interface.
Signed-off-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Another step towards removing sector-based interfaces: convert
the maximum write and minimum alignment values from sectors to
bytes. Rename the variables to let the compiler check that all
users are converted to the new semantics.
The maximum remains an int as long as BDRV_REQUEST_MAX_SECTORS
is constrained by INT_MAX (this means that we can't even
support a 2G write_zeroes, but just under it) - changing
operation lengths to unsigned or to 64-bits is a much bigger
audit, and debatable if we even want to do it (since at the
core, a 32-bit platform will still have ssize_t as its
underlying limit on write()).
Meanwhile, alignment is changed to 'uint32_t', since it makes no
sense to have an alignment larger than the maximum write, and
less painful to use an unsigned type with well-defined behavior
in bit operations than to have to worry about what happens if
a driver mistakenly supplies a negative alignment.
Add an assert that no one was trying to use sectors to get a
write zeroes larger than 2G, and therefore that a later conversion
to bytes won't be impacted by keeping the limit at 32 bits.
Signed-off-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
When changing the BlockDriverState that a BdrvChild points to while the
node is currently drained, we must call the .drained_end() parent
callback. Conversely, when this means attaching a new node that is
already drained, we need to call .drained_begin().
bdrv_root_attach_child() takes now an opaque parameter, which is needed
because the callbacks must also be called if we're attaching a new child
to the BlockBackend when the root node is already drained, and they need
a way to identify the BlockBackend. Previously, child->opaque was set
too late and the callbacks would still see it as NULL.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
This patch removes the remaining users of bs->blk, which will allow us
to have multiple BBs on top of a single BDS. In the meantime, all checks
that are currently in place to prevent the user from creating such
setups can be switched to bdrv_has_blk() instead of accessing BDS.blk.
Future patches can allow them and e.g. enable users to mirror to a block
device that already has a BlockBackend on it.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
In order to get rid of bs->blk for bdrv_get_device_name() and
bdrv_get_device_or_node_name(), ask all parents for their name and
simply pick the first one.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
We want to get rid of BlockDriverState.blk in order to allow multiple
BlockBackends per BDS. Converting the device callbacks in block.c (which
assume a single BlockBackend) to per-child callbacks gets us rid of the
first few instances.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
This moves the throttling related part of the BDS life cycle management
to BlockBackend. The throttling group reference is now kept even when no
medium is inserted.
With this commit, throttling isn't disabled and then re-enabled any more
during graph reconfiguration. This fixes the temporary breakage of I/O
throttling when used with live snapshots or block jobs that manipulate
the graph.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Alberto Garcia <berto@igalia.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
This removes the last part of I/O throttling from block/io.c and moves
it to the BlockBackend.
Instead of having knowledge about throttling inside io.c, we can call a
BdrvChild callback .drained_begin/end, which happens to drain the
throttled requests for BlockBackend parents.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Alberto Garcia <berto@igalia.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
BlockBackends use it to get a back pointer from BdrvChild to
BlockBackend in any BdrvChildRole callbacks.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Alberto Garcia <berto@igalia.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
This patch changes where the throttling state is stored (used to be the
BlockDriverState, now it is the BlockBackend), but it doesn't actually
make it a BB level feature yet. For example, throttling is still
disabled when the BDS is detached from the BB.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
As a first step towards moving I/O throttling to the BlockBackend level,
this patch changes all pointers in struct ThrottleGroup from referencing
a BlockDriverState to referencing a BlockBackend.
This change is valid because we made sure that throttling can only be
enabled on BDSes which have a BB attached.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Alberto Garcia <berto@igalia.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
In some cases, we want to take a quorum child offline, and take
another child online.
Signed-off-by: Wen Congyang <wency@cn.fujitsu.com>
Signed-off-by: zhanghailiang <zhang.zhanghailiang@huawei.com>
Signed-off-by: Gonglei <arei.gonglei@huawei.com>
Signed-off-by: Changlong Xie <xiecl.fnst@cn.fujitsu.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Alberto Garcia <berto@igalia.com>
Message-id: 1462865799-19402-2-git-send-email-xiecl.fnst@cn.fujitsu.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
The block layer has a couple of cases where it can lose
Force Unit Access semantics when writing a large block of
zeroes, such that the request returns before the zeroes
have been guaranteed to land on underlying media.
SCSI does not support FUA during WRITESAME(10/16); FUA is only
supported if it falls back to WRITE(10/16). But where the
underlying device is new enough to not need a fallback, it
means that any upper layer request with FUA semantics was
silently ignoring BDRV_REQ_FUA.
Conversely, NBD has situations where it can support FUA but not
ZERO_WRITE; when that happens, the generic block layer fallback
to bdrv_driver_pwritev() (or the older bdrv_co_writev() in qemu
2.6) was losing the FUA flag.
The problem of losing flags unrelated to ZERO_WRITE has been
latent in bdrv_co_do_write_zeroes() since commit aa7bfbff, but
back then, it did not matter because there was no FUA flag. It
became observable when commit 93f5e6d8 paved the way for flags
that can impact correctness, when we should have been using
bdrv_co_writev_flags() with modified flags. Compare to commit
9eeb6dd, which got flag manipulation right in
bdrv_co_do_zero_pwritev().
Symptoms: I tested with qemu-io with default writethrough cache
(which is supposed to use FUA semantics on every write), and
targetted an NBD client connected to a server that intentionally
did not advertise NBD_FLAG_SEND_FUA. When doing 'write 0 512',
the NBD client sent two operations (NBD_CMD_WRITE then
NBD_CMD_FLUSH) to get the fallback FUA semantics; but when doing
'write -z 0 512', the NBD client sent only NBD_CMD_WRITE.
The fix is do to a cleanup bdrv_co_flush() at the end of the
operation if any step in the middle relied on a BDS that does
not natively support FUA for that step (note that we don't
need to flush after every operation, if the operation is broken
into chunks based on bounce-buffer sizing). Each BDS gains a
new flag .supported_zero_flags, which parallels the use of
.supported_write_flags but only when accessing a zero write
operation (the flags MUST be different, because of SCSI having
different semantics based on WRITE vs. WRITESAME; and also
because BDRV_REQ_MAY_UNMAP only makes sense on zero writes).
Also fix some documentation to describe -ENOTSUP semantics,
particularly since iscsi depends on those semantics.
Down the road, we may want to add a driver where its
.bdrv_co_pwritev() honors all three of BDRV_REQ_FUA,
BDRV_REQ_ZERO_WRITE, and BDRV_REQ_MAY_UNMAP, and advertise
this via bs->supported_write_flags for blocks opened by that
driver; such a driver should NOT supply .bdrv_co_write_zeroes
nor .supported_zero_flags. But none of the drivers touched
in this patch want to do that (the act of writing zeroes is
different enough from normal writes to deserve a second
callback).
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Pre-patch, .supported_write_flags lives at the driver level, which
means we are blindly declaring that all block devices using a
given driver will either equally support FUA, or that we need a
fallback at the block layer. But there are drivers where FUA
support is a per-block decision: the NBD block driver is dependent
on the remote server advertising NBD_FLAG_SEND_FUA (and has
fallback code to duplicate the flush that the block layer would do
if NBD had not set .supported_write_flags); and the iscsi block
driver is dependent on the mode sense bits advertised by the
underlying device (and is currently silently ignoring FUA requests
if the underlying device does not support FUA).
The fix is to make supported flags as a per-BDS option, set during
.bdrv_open(). This patch moves the variable and fixes NBD and iscsi
to set it only conditionally; later patches will then further
simplify the NBD driver to quit duplicating work done at the block
layer, as well as tackle the fact that SCSI does not support FUA
semantics on WRITESAME(10/16) but only on WRITE(10/16).
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Vmdk images have metadata to indicate the vmware virtual
hardware version image was created/tested to run with.
Allow users to specify that version via new 'hwversion'
option.
[ kwolf: Adjust qemu-iotests common.filter ]
Signed-off-by: Janne Karhunen <Janne.Karhunen@gmail.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
There are no block drivers left that implement the old .bdrv_read/write
interface, so it can be removed now. This gets us rid of the
corresponding emulation functions, too.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Many parts of the block layer are already byte granularity. The block
driver interface, however, was still missing an interface that allows
making use of this. This patch introduces a new BlockDriver interface,
which is based on coroutines, vectored, has flags and uses a byte
granularity. This is now the preferred interface for new drivers.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
It used to be an internal helper function just for implementing
bdrv_co_do_readv/writev(), but now that it's a public interface, it
deserves a name without "do" in it.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Extract the handling of io_plug "depth" from linux-aio.c and let the
main bdrv_drain loop do nothing but wait on I/O.
Like the two newly introduced functions, bdrv_io_plug and bdrv_io_unplug
now operate on all children. The visit order is now symmetrical between
plug and unplug, making it possible for formats to implement plug/unplug.
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Extract the handling of throttling from bdrv_flush_io_queue. These
new functions will soon become BdrvChildRole callbacks, as they can
be generalized to "beginning of drain" and "end of drain".
Reviewed-by: Alberto Garcia <berto@igalia.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This function will allow drivers to implement BDRV_REQ_FUA natively
instead of sending a separate flush after the write.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Whether a write cache is used or not is a decision that concerns the
user (e.g. the guest device) rather than the backend. It was already
logically part of the BB level as bdrv_move_feature_fields() always kept
it on top of the BDS tree; with this patch, the core of it (the actual
flag and the additional flushes) is also implemented there.
Direct callers of bdrv_open() must pass BDRV_O_CACHE_WB now if bs
doesn't have a BlockBackend attached.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
This patch adds callback for flush request. This callback is responsible
for flushing whole block devices stack. bdrv_flush function does not
proceed to underlying devices. It should be performed by this callback
function, if needed.
Signed-off-by: Pavel Dovgalyuk <pavel.dovgaluk@ispras.ru>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The function is unused since commit f21d96d0 ('block: Use BdrvChild in
BlockBackend').
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
