A good 9p client sends T_readdir with "count" parameter that's sufficiently
smaller than client's initially negotiated msize (maximum message size).
We perform a check for that though to avoid the server to be interrupted
with a "Failed to encode VirtFS reply type 41" transport error message by
bad clients. This count value constraint uses msize - 11, because 11 is the
header size of R_readdir.
Signed-off-by: Christian Schoenebeck <qemu_oss@crudebyte.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Message-Id: <3990d3891e8ae2074709b56449e96ab4b4b93b7d.1579567020.git.qemu_oss@crudebyte.com>
[groug: added comment ]
Signed-off-by: Greg Kurz <groug@kaod.org>
A client establishes a session by sending a Tversion request along with a
'msize' parameter which client uses to suggest server a maximum message
size ever to be used for communication (for both requests and replies)
between client and server during that session. If client suggests a 'msize'
smaller than 4096 then deny session by server immediately with an error
response (Rlerror for "9P2000.L" clients or Rerror for "9P2000.u" clients)
instead of replying with Rversion.
So far any msize submitted by client with Tversion was simply accepted by
server without any check. Introduction of some minimum msize makes sense,
because e.g. a msize < 7 would not allow any subsequent 9p operation at
all, because 7 is the size of the header section common by all 9p message
types.
A substantial higher value of 4096 was chosen though to prevent potential
issues with some message types. E.g. Rreadlink may yield up to a size of
PATH_MAX which is usually 4096, and like almost all 9p message types,
Rreadlink is not allowed to be truncated by the 9p protocol. This chosen
size also prevents a similar issue with Rreaddir responses (provided client
always sends adequate 'count' parameter with Treaddir), because even though
directory entries retrieval may be split up over several T/Rreaddir
messages; a Rreaddir response must not truncate individual directory entries
though. So msize should be large enough to return at least one directory
entry with the longest possible file name supported by host. Most file
systems support a max. file name length of 255. Largest known file name
lenght limit would be currently ReiserFS with max. 4032 bytes, which is
also covered by this min. msize value because 4032 + 35 < 4096.
Furthermore 4096 is already the minimum msize of the Linux kernel's 9pfs
client.
Signed-off-by: Christian Schoenebeck <qemu_oss@crudebyte.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Message-Id: <8ceecb7fb9fdbeabbe55c04339349a36929fb8e3.1579567019.git.qemu_oss@crudebyte.com>
Signed-off-by: Greg Kurz <groug@kaod.org>
'out' label in v9fs_xattr_write() and 'out_nofid' label in
v9fs_complete_rename() can be replaced by appropriate return
calls.
CC: Greg Kurz <groug@kaod.org>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Acked-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Greg Kurz <groug@kaod.org>
init_in_iov_from_pdu might not be able to allocate the full buffer size
requested, which comes from the client and could be larger than the
transport has available at the time of the request. Specifically, this
can happen with read operations, with the client requesting a read up to
the max allowed, which might be more than the transport has available at
the time.
Today the implementation of init_in_iov_from_pdu throws an error, both
Xen and Virtio.
Instead, change the V9fsTransport interface so that the size becomes a
pointer and can be limited by the implementation of
init_in_iov_from_pdu.
Change both the Xen and Virtio implementations to set the size to the
size of the buffer they managed to allocate, instead of throwing an
error. However, if the allocated buffer size is less than P9_IOHDRSZ
(the size of the header) still throw an error as the case is unhandable.
Signed-off-by: Stefano Stabellini <stefano.stabellini@xilinx.com>
CC: groug@kaod.org
CC: anthony.perard@citrix.com
CC: roman@zededa.com
CC: qemu_oss@crudebyte.com
[groug: fix 32-bit build]
Signed-off-by: Greg Kurz <groug@kaod.org>
Some filesystems may return 0s in statfs (trivially, a FUSE filesystem
can do so). QEMU should handle this gracefully and just behave the
same as if statfs failed.
Signed-off-by: Dan Schatzberg <dschatzberg@fb.com>
Acked-by: Christian Schoenebeck <qemu_oss@crudebyte.com>
Signed-off-by: Greg Kurz <groug@kaod.org>
Use variable length suffixes for inode remapping instead of the fixed
16 bit size prefixes before. With this change the inode numbers on guest
will typically be much smaller (e.g. around >2^1 .. >2^7 instead of >2^48
with the previous fixed size inode remapping.
Additionally this solution is more efficient, since inode numbers in
practice can take almost their entire 64 bit range on guest as well, so
there is less likely a need for generating and tracking additional suffixes,
which might also be beneficial for nested virtualization where each level of
virtualization would shift up the inode bits and increase the chance of
expensive remapping actions.
The "Exponential Golomb" algorithm is used as basis for generating the
variable length suffixes. The algorithm has a parameter k which controls the
distribution of bits on increasing indeces (minimum bits at low index vs.
maximum bits at high index). With k=0 the generated suffixes look like:
Index Dec/Bin -> Generated Suffix Bin
1 [1] -> [1] (1 bits)
2 [10] -> [010] (3 bits)
3 [11] -> [110] (3 bits)
4 [100] -> [00100] (5 bits)
5 [101] -> [10100] (5 bits)
6 [110] -> [01100] (5 bits)
7 [111] -> [11100] (5 bits)
8 [1000] -> [0001000] (7 bits)
9 [1001] -> [1001000] (7 bits)
10 [1010] -> [0101000] (7 bits)
11 [1011] -> [1101000] (7 bits)
12 [1100] -> [0011000] (7 bits)
...
65533 [1111111111111101] -> [1011111111111111000000000000000] (31 bits)
65534 [1111111111111110] -> [0111111111111111000000000000000] (31 bits)
65535 [1111111111111111] -> [1111111111111111000000000000000] (31 bits)
Hence minBits=1 maxBits=31
And with k=5 they would look like:
Index Dec/Bin -> Generated Suffix Bin
1 [1] -> [000001] (6 bits)
2 [10] -> [100001] (6 bits)
3 [11] -> [010001] (6 bits)
4 [100] -> [110001] (6 bits)
5 [101] -> [001001] (6 bits)
6 [110] -> [101001] (6 bits)
7 [111] -> [011001] (6 bits)
8 [1000] -> [111001] (6 bits)
9 [1001] -> [000101] (6 bits)
10 [1010] -> [100101] (6 bits)
11 [1011] -> [010101] (6 bits)
12 [1100] -> [110101] (6 bits)
...
65533 [1111111111111101] -> [0011100000000000100000000000] (28 bits)
65534 [1111111111111110] -> [1011100000000000100000000000] (28 bits)
65535 [1111111111111111] -> [0111100000000000100000000000] (28 bits)
Hence minBits=6 maxBits=28
Signed-off-by: Christian Schoenebeck <qemu_oss@crudebyte.com>
Signed-off-by: Greg Kurz <groug@kaod.org>
stat_to_qid attempts via qid_path_prefixmap to map unique files (which are
identified by 64 bit inode nr and 32 bit device id) to a 64 QID path value.
However this implementation makes some assumptions about inode number
generation on the host.
If qid_path_prefixmap fails, we still have 48 bits available in the QID
path to fall back to a less memory efficient full mapping.
Signed-off-by: Antonios Motakis <antonios.motakis@huawei.com>
[CS: - Rebased to https://github.com/gkurz/qemu/commits/9p-next
(SHA1 7fc4c49e91).
- Updated hash calls to new xxhash API.
- Removed unnecessary parantheses in qpf_lookup_func().
- Removed unnecessary g_malloc0() result checks.
- Log error message when running out of prefixes in
qid_path_fullmap().
- Log warning message about potential degraded performance in
qid_path_prefixmap().
- Wrapped qpf_table initialization to dedicated qpf_table_init()
function.
- Fixed typo in comment. ]
Signed-off-by: Christian Schoenebeck <qemu_oss@crudebyte.com>
Signed-off-by: Greg Kurz <groug@kaod.org>
'warn' (default): Only log an error message (once) on host if more than one
device is shared by same export, except of that just ignore this config
error though. This is the default behaviour for not breaking existing
installations implying that they really know what they are doing.
'forbid': Like 'warn', but except of just logging an error this
also denies access of guest to additional devices.
'remap': Allows to share more than one device per export by remapping
inodes from host to guest appropriately. To support multiple devices on the
9p share, and avoid qid path collisions we take the device id as input to
generate a unique QID path. The lowest 48 bits of the path will be set
equal to the file inode, and the top bits will be uniquely assigned based
on the top 16 bits of the inode and the device id.
Signed-off-by: Antonios Motakis <antonios.motakis@huawei.com>
[CS: - Rebased to https://github.com/gkurz/qemu/commits/9p-next
(SHA1 7fc4c49e91).
- Added virtfs option 'multidevs', original patch simply did the inode
remapping without being asked.
- Updated hash calls to new xxhash API.
- Updated docs for new option 'multidevs'.
- Fixed v9fs_do_readdir() not having remapped inodes.
- Log error message when running out of prefixes in
qid_path_prefixmap().
- Fixed definition of QPATH_INO_MASK.
- Wrapped qpp_table initialization to dedicated qpp_table_init()
function.
- Dropped unnecessary parantheses in qpp_lookup_func().
- Dropped unnecessary g_malloc0() result checks. ]
Signed-off-by: Christian Schoenebeck <qemu_oss@crudebyte.com>
[groug: - Moved "multidevs" parsing to the local backend.
- Added hint to invalid multidevs option error.
- Turn "remap" into "x-remap". ]
Signed-off-by: Greg Kurz <groug@kaod.org>
The QID path should uniquely identify a file. However, the
inode of a file is currently used as the QID path, which
on its own only uniquely identifies files within a device.
Here we track the device hosting the 9pfs share, in order
to prevent security issues with QID path collisions from
other devices.
We only print a warning for now but a subsequent patch will
allow users to have finer control over the desired behaviour.
Failing the I/O will be one the proposed behaviour, so we
also change stat_to_qid() to return an error here in order to
keep other patches simpler.
Signed-off-by: Antonios Motakis <antonios.motakis@huawei.com>
[CS: - Assign dev_id to export root's device already in
v9fs_device_realize_common(), not postponed in
stat_to_qid().
- error_report_once() if more than one device was
shared by export.
- Return -ENODEV instead of -ENOSYS in stat_to_qid().
- Fixed typo in log comment. ]
Signed-off-by: Christian Schoenebeck <qemu_oss@crudebyte.com>
[groug, changed to warning, updated message and changelog]
Signed-off-by: Greg Kurz <groug@kaod.org>
There is no need for signedness on these QID fields for 9p.
Signed-off-by: Antonios Motakis <antonios.motakis@huawei.com>
[CS: - Also make QID type unsigned.
- Adjust donttouch_stat() to new types.
- Adjust trace-events to new types. ]
Signed-off-by: Christian Schoenebeck <qemu_oss@crudebyte.com>
Signed-off-by: Greg Kurz <groug@kaod.org>
In my "build everything" tree, changing qemu/main-loop.h triggers a
recompile of some 5600 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h). It includes block/aio.h,
which in turn includes qemu/event_notifier.h, qemu/notify.h,
qemu/processor.h, qemu/qsp.h, qemu/queue.h, qemu/thread-posix.h,
qemu/thread.h, qemu/timer.h, and a few more.
Include qemu/main-loop.h only where it's needed. Touching it now
recompiles only some 1700 objects. For block/aio.h and
qemu/event_notifier.h, these numbers drop from 5600 to 2800. For the
others, they shrink only slightly.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190812052359.30071-21-armbru@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Because it is a recommended coding practice (see HACKING).
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Anthony PERARD <anthony.perard@citrix.com>
When using the 9P2000.u version of the protocol, the following shell
command line in the guest can cause QEMU to crash:
while true; do rm -rf aa; mkdir -p a/b & touch a/b/c & mv a aa; done
With 9P2000.u, file renaming is handled by the WSTAT command. The
v9fs_wstat() function calls v9fs_complete_rename(), which calls
v9fs_fix_path() for every fid whose path is affected by the change.
The involved calls to v9fs_path_copy() may race with any other access
to the fid path performed by some worker thread, causing a crash like
shown below:
Thread 12 "qemu-system-x86" received signal SIGSEGV, Segmentation fault.
0x0000555555a25da2 in local_open_nofollow (fs_ctx=0x555557d958b8, path=0x0,
flags=65536, mode=0) at hw/9pfs/9p-local.c:59
59 while (*path && fd != -1) {
(gdb) bt
#0 0x0000555555a25da2 in local_open_nofollow (fs_ctx=0x555557d958b8,
path=0x0, flags=65536, mode=0) at hw/9pfs/9p-local.c:59
#1 0x0000555555a25e0c in local_opendir_nofollow (fs_ctx=0x555557d958b8,
path=0x0) at hw/9pfs/9p-local.c:92
#2 0x0000555555a261b8 in local_lstat (fs_ctx=0x555557d958b8,
fs_path=0x555556b56858, stbuf=0x7fff84830ef0) at hw/9pfs/9p-local.c:185
#3 0x0000555555a2b367 in v9fs_co_lstat (pdu=0x555557d97498,
path=0x555556b56858, stbuf=0x7fff84830ef0) at hw/9pfs/cofile.c:53
#4 0x0000555555a1e9e2 in v9fs_stat (opaque=0x555557d97498)
at hw/9pfs/9p.c:1083
#5 0x0000555555e060a2 in coroutine_trampoline (i0=-669165424, i1=32767)
at util/coroutine-ucontext.c:116
#6 0x00007fffef4f5600 in __start_context () at /lib64/libc.so.6
#7 0x0000000000000000 in ()
(gdb)
The fix is to take the path write lock when calling v9fs_complete_rename(),
like in v9fs_rename().
Impact: DoS triggered by unprivileged guest users.
Fixes: CVE-2018-19489
Cc: P J P <ppandit@redhat.com>
Reported-by: zhibin hu <noirfate@gmail.com>
Reviewed-by: Prasad J Pandit <pjp@fedoraproject.org>
Signed-off-by: Greg Kurz <groug@kaod.org>
Recent commit 5b76ef50f6 fixed a race where v9fs_co_open2() could
possibly overwrite a fid path with v9fs_path_copy() while it is being
accessed by some other thread, ie, use-after-free that can be detected
by ASAN with a custom 9p client.
It turns out that the same can happen at several locations where
v9fs_path_copy() is used to set the fid path. The fix is again to
take the write lock.
Fixes CVE-2018-19364.
Cc: P J P <ppandit@redhat.com>
Reported-by: zhibin hu <noirfate@gmail.com>
Reviewed-by: Prasad J Pandit <pjp@fedoraproject.org>
Signed-off-by: Greg Kurz <groug@kaod.org>
As with unlinkat, these flags come from the client and need to
be translated to their host values. The protocol values happen
to match linux, but that need not be true in general.
Signed-off-by: Keno Fischer <keno@juliacomputing.com>
Signed-off-by: Greg Kurz <groug@kaod.org>
The 9p-local code previously relied on P9_DOTL_AT_REMOVEDIR and AT_REMOVEDIR
having the same numerical value and deferred any errorchecking to the
syscall itself. However, while the former assumption is true on Linux,
it is not true in general. 9p-handle did this properly however. Move
the translation code to the generic 9p server code and add an error
if unrecognized flags are passed.
Signed-off-by: Keno Fischer <keno@juliacomputing.com>
Signed-off-by: Greg Kurz <groug@kaod.org>
If the size returned from llistxattr/lgetxattr is 0, we skipped
the malloc call, leaving xattr.value uninitialized. However, this
value is later passed to `g_free` without any further checks,
causing an error. Fix that by always calling g_malloc unconditionally.
If `size` is 0, it will return NULL, which is safe to pass to g_free.
Signed-off-by: Keno Fischer <keno@juliacomputing.com>
Signed-off-by: Greg Kurz <groug@kaod.org>
Don't print the tv_nsec part of atime and mtime, to stay below the 10
argument limit of trace events.
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
lhs/rhs doesn't tell much about how argument are handled, dst/src is
and const arguments is clearer in my mind. Use g_memdup() while at it.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Greg Kurz <groug@kaod.org>
The idea is to send a victim request that will possibly block in the
server and to send a flush request to cancel the victim request.
This patch adds two test to verifiy that:
- the server does not reply to a victim request that was actually
cancelled
- the server replies to the flush request after replying to the
victim request if it could not cancel it
9p request cancellation reference:
http://man.cat-v.org/plan_9/5/flush
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
(groug, change the test to only write a single byte to avoid
any alignment or endianess consideration)
# Background
I was investigating spurious non-deterministic EINTR returns from
various 9p file system operations in a Linux guest served from the
qemu 9p server.
## EINTR, ERESTARTSYS and the linux kernel
When a signal arrives that the Linux kernel needs to deliver to user-space
while a given thread is blocked (in the 9p case waiting for a reply to its
request in 9p_client_rpc -> wait_event_interruptible), it asks whatever
driver is currently running to abort its current operation (in the 9p case
causing the submission of a TFLUSH message) and return to user space.
In these situations, the error message reported is generally ERESTARTSYS.
If the userspace processes specified SA_RESTART, this means that the
system call will get restarted upon completion of the signal handler
delivery (assuming the signal handler doesn't modify the process state
in complicated ways not relevant here). If SA_RESTART is not specified,
ERESTARTSYS gets translated to EINTR and user space is expected to handle
the restart itself.
## The 9p TFLUSH command
The 9p TFLUSH commands requests that the server abort an ongoing operation.
The man page [1] specifies:
```
If it recognizes oldtag as the tag of a pending transaction, it should
abort any pending response and discard that tag.
[...]
When the client sends a Tflush, it must wait to receive the corresponding
Rflush before reusing oldtag for subsequent messages. If a response to the
flushed request is received before the Rflush, the client must honor the
response as if it had not been flushed, since the completed request may
signify a state change in the server
```
In particular, this means that the server must not send a reply with the
orignal tag in response to the cancellation request, because the client is
obligated to interpret such a reply as a coincidental reply to the original
request.
# The bug
When qemu receives a TFlush request, it sets the `cancelled` flag on the
relevant pdu. This flag is periodically checked, e.g. in
`v9fs_co_name_to_path`, and if set, the operation is aborted and the error
is set to EINTR. However, the server then violates the spec, by returning
to the client an Rerror response, rather than discarding the message
entirely. As a result, the client is required to assume that said Rerror
response is a result of the original request, not a result of the
cancellation and thus passes the EINTR error back to user space.
This is not the worst thing it could do, however as discussed above, the
correct error code would have been ERESTARTSYS, such that user space
programs with SA_RESTART set get correctly restarted upon completion of
the signal handler.
Instead, such programs get spurious EINTR results that they were not
expecting to handle.
It should be noted that there are plenty of user space programs that do not
set SA_RESTART and do not correctly handle EINTR either. However, that is
then a userspace bug. It should also be noted that this bug has been
mitigated by a recent commit to the Linux kernel [2], which essentially
prevents the kernel from sending Tflush requests unless the process is about
to die (in which case the process likely doesn't care about the response).
Nevertheless, for older kernels and to comply with the spec, I believe this
change is beneficial.
# Implementation
The fix is fairly simple, just skipping notification of a reply if
the pdu was previously cancelled. We do however, also notify the transport
layer that we're doing this, so it can clean up any resources it may be
holding. I also added a new trace event to distinguish
operations that caused an error reply from those that were cancelled.
One complication is that we only omit sending the message on EINTR errors in
order to avoid confusing the rest of the code (which may assume that a
client knows about a fid if it sucessfully passed it off to pud_complete
without checking for cancellation status). This does mean that if the server
acts upon the cancellation flag, it always needs to set err to EINTR. I
believe this is true of the current code.
[1] https://9fans.github.io/plan9port/man/man9/flush.html
[2] https://github.com/torvalds/linux/commit/9523feac272ccad2ad8186ba4fcc891
Signed-off-by: Keno Fischer <keno@juliacomputing.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
[groug, send a zero-sized reply instead of detaching the buffer]
Signed-off-by: Greg Kurz <groug@kaod.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
No good reasons to do this outside of v9fs_device_realize_common().
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
This patch changes some error messages in the backend init code and
convert backends to propagate QEMU Error objects instead of calling
error_report().
One notable improvement is that the local backend now provides a more
detailed error report when it fails to open the shared directory.
Signed-off-by: Greg Kurz <groug@kaod.org>
If we receive an unsupported request id, we first decide to
return -ENOTSUPP to the client, but since the request id
causes is_read_only_op() to return false, we change the
error to be -EROFS if the fsdev is read-only. This doesn't
make sense since we don't know what the client asked for.
This patch ensures that -EROFS can only be returned if the
request id is supported.
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Eric Blake <eblake@redhat.com>
The return value of v9fs_mark_fids_unreclaim() is then propagated to
pdu_complete(). It should be a negative errno, not -1.
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Eric Blake <eblake@redhat.com>
9p back-end first queries the size of an extended attribute,
allocates space for it via g_malloc() and then retrieves its
value into allocated buffer. Race between querying attribute
size and retrieving its could lead to memory bytes disclosure.
Use g_malloc0() to avoid it.
Reported-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Signed-off-by: Greg Kurz <groug@kaod.org>
v9fs_do_readdir_with_stat() should check for a maximum buffer size
before an attempt to marshal gathered data. Otherwise, buffers assumed
as misconfigured and the transport would be broken.
The patch brings v9fs_do_readdir_with_stat() in conformity with
v9fs_do_readdir() behavior.
Signed-off-by: Jan Dakinevich <jan.dakinevich@gmail.com>
[groug, regression caused my commit 8d37de41ca # 2.10]
Signed-off-by: Greg Kurz <groug@kaod.org>
The third parameter of v9fs_co_name_to_path() must not contain `/'
character.
The issue is most likely related to 9p2000.u protocol only.
Signed-off-by: Jan Dakinevich <jan.dakinevich@gmail.com>
[groug, regression caused by commit f57f587857 # 2.10]
Signed-off-by: Greg Kurz <groug@kaod.org>
If the client is using 9p2000.u, the following occurs:
$ cd ${virtfs_shared_dir}
$ mkdir -p a/b/c
$ ls a/b
ls: cannot access 'a/b/a': No such file or directory
ls: cannot access 'a/b/b': No such file or directory
a b c
instead of the expected:
$ ls a/b
c
This is a regression introduced by commit f57f5878578a;
local_name_to_path() now resolves ".." and "." in paths,
and v9fs_do_readdir_with_stat()->stat_to_v9stat() then
copies the basename of the resulting path to the response.
With the example above, this means that "." and ".." are
turned into "b" and "a" respectively...
stat_to_v9stat() currently assumes it is passed a full
canonicalized path and uses it to do two different things:
1) to pass it to v9fs_co_readlink() in case the file is a symbolic
link
2) to set the name field of the V9fsStat structure to the basename
part of the given path
It only has two users: v9fs_stat() and v9fs_do_readdir_with_stat().
v9fs_stat() really needs 1) and 2) to be performed since it starts
with the full canonicalized path stored in the fid. It is different
for v9fs_do_readdir_with_stat() though because the name we want to
put into the V9fsStat structure is the d_name field of the dirent
actually (ie, we want to keep the "." and ".." special names). So,
we only need 1) in this case.
This patch hence adds a basename argument to stat_to_v9stat(), to
be used to set the name field of the V9fsStat structure, and moves
the basename logic to v9fs_stat().
Signed-off-by: Jan Dakinevich <jan.dakinevich@gmail.com>
(groug, renamed old name argument to path and updated changelog)
Signed-off-by: Greg Kurz <groug@kaod.org>
(note this is how other functions also handle the errors).
hw/9pfs/9p.c:948:18: warning: Loss of sign in implicit conversion
offset = err;
^~~
Reported-by: Clang Static Analyzer
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Greg Kurz <groug@kaod.org>
Convert all uses of error_report("warning:"... to use warn_report()
instead. This helps standardise on a single method of printing warnings
to the user.
All of the warnings were changed using these two commands:
find ./* -type f -exec sed -i \
's|error_report(".*warning[,:] |warn_report("|Ig' {} +
Indentation fixed up manually afterwards.
The test-qdev-global-props test case was manually updated to ensure that
this patch passes make check (as the test cases are case sensitive).
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Suggested-by: Thomas Huth <thuth@redhat.com>
Cc: Jeff Cody <jcody@redhat.com>
Cc: Kevin Wolf <kwolf@redhat.com>
Cc: Max Reitz <mreitz@redhat.com>
Cc: Ronnie Sahlberg <ronniesahlberg@gmail.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Peter Lieven <pl@kamp.de>
Cc: Josh Durgin <jdurgin@redhat.com>
Cc: "Richard W.M. Jones" <rjones@redhat.com>
Cc: Markus Armbruster <armbru@redhat.com>
Cc: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: "Aneesh Kumar K.V" <aneesh.kumar@linux.vnet.ibm.com>
Cc: Greg Kurz <groug@kaod.org>
Cc: Rob Herring <robh@kernel.org>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Peter Chubb <peter.chubb@nicta.com.au>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Marcel Apfelbaum <marcel@redhat.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Cc: David Gibson <david@gibson.dropbear.id.au>
Cc: Alexander Graf <agraf@suse.de>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Cornelia Huck <cohuck@redhat.com>
Cc: Stefan Hajnoczi <stefanha@redhat.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Greg Kurz <groug@kaod.org>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed by: Peter Chubb <peter.chubb@data61.csiro.au>
Acked-by: Max Reitz <mreitz@redhat.com>
Acked-by: Marcel Apfelbaum <marcel@redhat.com>
Message-Id: <e1cfa2cd47087c248dd24caca9c33d9af0c499b0.1499866456.git.alistair.francis@xilinx.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Contrary to what is written in the comment, a buggy guest can misconfigure
the transport buffers and pdu_marshal() may return an error. If this ever
happens, it is up to the transport layer to handle the situation (9P is
transport agnostic).
This fixes Coverity issue CID1348518.
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
The 9P protocol is transport agnostic: if the guest misconfigured the
buffers, the best we can do is to set the broken flag on the device.
Signed-off-by: Greg Kurz <groug@kaod.org>
In mapped security modes, files are created with very restrictive
permissions (600 for files and 700 for directories). This makes
file sharing between virtual machines and users on the host rather
complicated. Imagine eg. a group of users that need to access data
produced by processes on a virtual machine. Giving those users access
to the data will be difficult since the group access mode is always 0.
This patch makes the default mode for both files and directories
configurable. Existing setups that don't know about the new parameters
keep using the current secure behavior.
Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
Signed-off-by: Greg Kurz <groug@kaod.org>
These v9fs_co_name_to_path() call sites have always been around. I guess
no care was taken to check the return value because the name_to_path
operation could never fail at the time. This is no longer true: the
handle and synth backends can already fail this operation, and so will the
local backend soon.
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Eric Blake <eblake@redhat.com>
Only pdu_complete() needs to notify the client that a request has completed.
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
These bits aren't related to the transport so let's move them to the core
code.
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
This allows us to remove lots of includes of migration/migration.h
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
The migration blocker survives a device reset: if the guest mounts a 9p
share and then gets rebooted with system_reset, it will be unmigratable
until it remounts and umounts the 9p share again.
This happens because the migration blocker is supposed to be cleared when
we put the last reference on the root fid, but virtfs_reset() wrongly calls
free_fid() instead of put_fid().
This patch fixes virtfs_reset() so that it honor the way fids are supposed
to be manipulated: first get a reference and later put it back when you're
done.
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Li Qiang <liqiang6-s@360.cn>
If a client tries to flush the same outstanding request several times, only
the first flush completes. Subsequent ones keep waiting for the request
completion in v9fs_flush() and, therefore, leak a PDU. This will cause QEMU
to hang when draining active PDUs the next time the device is reset.
Let have each flush request wake up the next one if any. The last waiter
frees the cancelled PDU.
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Eric Blake <eblake@redhat.com>
The v9fs_create() and v9fs_lcreate() functions are used to create a file
on the backend and to associate it to a fid. The fid shouldn't be already
in-use, otherwise both functions may silently leak a file descriptor or
allocated memory. The current code doesn't check that.
This patch ensures that the fid isn't already associated to anything
before using it.
Signed-off-by: Li Qiang <liqiang6-s@360.cn>
(reworded the changelog, Greg Kurz)
Signed-off-by: Greg Kurz <groug@kaod.org>
According to the 9P spec [*], when a client wants to cancel a pending I/O
request identified by a given tag (uint16), it must send a Tflush message
and wait for the server to respond with a Rflush message before reusing this
tag for another I/O. The server may still send a completion message for the
I/O if it wasn't actually cancelled but the Rflush message must arrive after
that.
QEMU hence waits for the flushed PDU to complete before sending the Rflush
message back to the client.
If a client sends 'Tflush tag oldtag' and tag == oldtag, QEMU will then
allocate a PDU identified by tag, find it in the PDU list and wait for
this same PDU to complete... i.e. wait for a completion that will never
happen. This causes a tag and ring slot leak in the guest, and a PDU
leak in QEMU, all of them limited by the maximal number of PDUs (128).
But, worse, this causes QEMU to hang on device reset since v9fs_reset()
wants to drain all pending I/O.
This insane behavior is likely to denote a bug in the client, and it would
deserve an Rerror message to be sent back. Unfortunately, the protocol
allows it and requires all flush requests to suceed (only a Tflush response
is expected).
The only option is to detect when we have to handle a self-referencing
flush request and report success to the client right away.
[*] http://man.cat-v.org/plan_9/5/flush
Reported-by: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: Greg Kurz <groug@kaod.org>
This patchset adds the throttle support for the 9p-local driver.
For now this functionality can be enabled only through qemu cli options.
QMP interface and support to other drivers need further extensions.
To make it simple for other 9p drivers, the throttle code has been put in
separate files.
Signed-off-by: Pradeep Jagadeesh <pradeep.jagadeesh@huawei.com>
Reviewed-by: Alberto Garcia <berto@igalia.com>
(pass extra NULL CoMutex * argument to qemu_co_queue_wait(),
added options to qemu-options.hx, Greg Kurz)
Signed-off-by: Greg Kurz <groug@kaod.org>
In this case, we are marshaling an error status instead of the errno value.
Reorganize the out and out_nofid labels to look like all the other cases.
Coverity reports this because the "err = -ENOENT" and "err = -EINVAL"
assignments above are dead, overwritten by the call to pdu_marshal.
(Coverity issues CID1348512 and CID1348513)
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
(also open-coded the success path since locking is a nop for us, Greg Kurz)
Signed-off-by: Greg Kurz <groug@kaod.org>
All that CoQueue needs in order to become thread-safe is help
from an external mutex. Add this to the API.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Message-id: 20170213181244.16297-6-pbonzini@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
cause 9p clients to hang. Other patches are minor enhancements.
-----BEGIN PGP SIGNATURE-----
iEYEABECAAYFAliIegsACgkQAvw66wEB28LjzwCeIKbBFC/hbc43UqaNX82OGd2v
soYAn0YYXJUAykyjNEMLdhhNp+rABzNk
=1PaE
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/gkurz/tags/for-upstream' into staging
This pull request fixes a 2.9 regression and a long standing bug that can
cause 9p clients to hang. Other patches are minor enhancements.
# gpg: Signature made Wed 25 Jan 2017 10:12:27 GMT
# gpg: using DSA key 0x02FC3AEB0101DBC2
# gpg: Good signature from "Greg Kurz <groug@kaod.org>"
# gpg: aka "Greg Kurz <groug@free.fr>"
# gpg: aka "Greg Kurz <gkurz@fr.ibm.com>"
# gpg: aka "Greg Kurz <gkurz@linux.vnet.ibm.com>"
# gpg: aka "Gregory Kurz (Groug) <groug@free.fr>"
# gpg: aka "Gregory Kurz (Cimai Technology) <gkurz@cimai.com>"
# gpg: aka "Gregory Kurz (Meiosys Technology) <gkurz@meiosys.com>"
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 2BD4 3B44 535E C0A7 9894 DBA2 02FC 3AEB 0101 DBC2
* remotes/gkurz/tags/for-upstream:
9pfs: fix offset error in v9fs_xattr_read()
9pfs: local: trivial cosmetic fix in pwritev op
9pfs: fix off-by-one error in PDU free list
tests: virtio-9p: improve error reporting
9pfs: add missing coroutine_fn annotations
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The current code tries to copy `read_count' bytes starting at offset
`offset' from a `read_count`-sized iovec. This causes v9fs_pack() to
fail with ENOBUFS.
Since the PDU iovec is already partially filled with `offset' bytes,
let's skip them when creating `qiov_full' and have v9fs_pack() to
copy the whole of it. Moreover, this is consistent with the other
places where v9fs_init_qiov_from_pdu() is called.
This fixes commit "bcb8998fac16 9pfs: call v9fs_init_qiov_from_pdu
before v9fs_pack".
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
