Only move the state machine to ReceivingData if there is no
pending error. This avoids later OOB access while processing
commands queued.
"SD Specifications Part 1 Physical Layer Simplified Spec. v3.01"
4.3.3 Data Read
Read command is rejected if BLOCK_LEN_ERROR or ADDRESS_ERROR
occurred and no data transfer is performed.
4.3.4 Data Write
Write command is rejected if BLOCK_LEN_ERROR or ADDRESS_ERROR
occurred and no data transfer is performed.
WP_VIOLATION errors are not modified: the error bit is set, we
stay in receive-data state, wait for a stop command. All further
data transfer is ignored. See the check on sd->card_status at the
beginning of sd_read_data() and sd_write_data().
Fixes: CVE-2020-13253
Cc: qemu-stable@nongnu.org
Reported-by: Alexander Bulekov <alxndr@bu.edu>
Buglink: https://bugs.launchpad.net/qemu/+bug/1880822
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20200630133912.9428-6-f4bug@amsat.org>
To make the next commit easier to review, clean this code first.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Alexander Bulekov <alxndr@bu.edu>
Message-Id: <20200630133912.9428-3-f4bug@amsat.org>
QEMU allows to create SD card with unrealistic sizes. This could
work, but some guests (at least Linux) consider sizes that are not
a power of 2 as a firmware bug and fix the card size to the next
power of 2.
While the possibility to use small SD card images has been seen as
a feature, it became a bug with CVE-2020-13253, where the guest is
able to do OOB read/write accesses past the image size end.
In a pair of commits we will fix CVE-2020-13253 as:
Read command is rejected if BLOCK_LEN_ERROR or ADDRESS_ERROR
occurred and no data transfer is performed.
Write command is rejected if BLOCK_LEN_ERROR or ADDRESS_ERROR
occurred and no data transfer is performed.
WP_VIOLATION errors are not modified: the error bit is set, we
stay in receive-data state, wait for a stop command. All further
data transfer is ignored. See the check on sd->card_status at the
beginning of sd_read_data() and sd_write_data().
While this is the correct behavior, in case QEMU create smaller SD
cards, guests still try to access past the image size end, and QEMU
considers this is an invalid address, thus "all further data transfer
is ignored". This is wrong and make the guest looping until
eventually timeouts.
Fix by not allowing invalid SD card sizes (suggesting the expected
size as a hint):
$ qemu-system-arm -M orangepi-pc -drive file=rootfs.ext2,if=sd,format=raw
qemu-system-arm: Invalid SD card size: 60 MiB
SD card size has to be a power of 2, e.g. 64 MiB.
You can resize disk images with 'qemu-img resize <imagefile> <new-size>'
(note that this will lose data if you make the image smaller than it currently is).
Cc: qemu-stable@nongnu.org
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20200713183209.26308-8-f4bug@amsat.org>
We don't need to check if sd->blk is set twice.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20200630133912.9428-18-f4bug@amsat.org>
Only SCSD cards support Class 6 (Block Oriented Write Protection)
commands.
"SD Specifications Part 1 Physical Layer Simplified Spec. v3.01"
4.3.14 Command Functional Difference in Card Capacity Types
* Write Protected Group
SDHC and SDXC do not support write-protected groups. Issuing
CMD28, CMD29 and CMD30 generates the ILLEGAL_COMMAND error.
Cc: qemu-stable@nongnu.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20200630133912.9428-7-f4bug@amsat.org>
If we want to check error after errp-function call, we need to
introduce local_err and then propagate it to errp. Instead, use
the ERRP_GUARD() macro, benefits are:
1. No need of explicit error_propagate call
2. No need of explicit local_err variable: use errp directly
3. ERRP_GUARD() leaves errp as is if it's not NULL or
&error_fatal, this means that we don't break error_abort
(we'll abort on error_set, not on error_propagate)
If we want to add some info to errp (by error_prepend() or
error_append_hint()), we must use the ERRP_GUARD() macro.
Otherwise, this info will not be added when errp == &error_fatal
(the program will exit prior to the error_append_hint() or
error_prepend() call). No such cases are being fixed here.
This commit is generated by command
sed -n '/^SD (Secure Card)$/,/^$/{s/^F: //p}' \
MAINTAINERS | \
xargs git ls-files | grep '\.[hc]$' | \
xargs spatch \
--sp-file scripts/coccinelle/errp-guard.cocci \
--macro-file scripts/cocci-macro-file.h \
--in-place --no-show-diff --max-width 80
Reported-by: Kevin Wolf <kwolf@redhat.com>
Reported-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
[Commit message tweaked]
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20200707165037.1026246-4-armbru@redhat.com>
[ERRP_AUTO_PROPAGATE() renamed to ERRP_GUARD(), and
auto-propagated-errp.cocci to errp-guard.cocci. Commit message
tweaked again.]
When all we do with an Error we receive into a local variable is
propagating to somewhere else, we can just as well receive it there
right away. Convert
if (!foo(..., &err)) {
...
error_propagate(errp, err);
...
return ...
}
to
if (!foo(..., errp)) {
...
...
return ...
}
where nothing else needs @err. Coccinelle script:
@rule1 forall@
identifier fun, err, errp, lbl;
expression list args, args2;
binary operator op;
constant c1, c2;
symbol false;
@@
if (
(
- fun(args, &err, args2)
+ fun(args, errp, args2)
|
- !fun(args, &err, args2)
+ !fun(args, errp, args2)
|
- fun(args, &err, args2) op c1
+ fun(args, errp, args2) op c1
)
)
{
... when != err
when != lbl:
when strict
- error_propagate(errp, err);
... when != err
(
return;
|
return c2;
|
return false;
)
}
@rule2 forall@
identifier fun, err, errp, lbl;
expression list args, args2;
expression var;
binary operator op;
constant c1, c2;
symbol false;
@@
- var = fun(args, &err, args2);
+ var = fun(args, errp, args2);
... when != err
if (
(
var
|
!var
|
var op c1
)
)
{
... when != err
when != lbl:
when strict
- error_propagate(errp, err);
... when != err
(
return;
|
return c2;
|
return false;
|
return var;
)
}
@depends on rule1 || rule2@
identifier err;
@@
- Error *err = NULL;
... when != err
Not exactly elegant, I'm afraid.
The "when != lbl:" is necessary to avoid transforming
if (fun(args, &err)) {
goto out
}
...
out:
error_propagate(errp, err);
even though other paths to label out still need the error_propagate().
For an actual example, see sclp_realize().
Without the "when strict", Coccinelle transforms vfio_msix_setup(),
incorrectly. I don't know what exactly "when strict" does, only that
it helps here.
The match of return is narrower than what I want, but I can't figure
out how to express "return where the operand doesn't use @err". For
an example where it's too narrow, see vfio_intx_enable().
Silently fails to convert hw/arm/armsse.c, because Coccinelle gets
confused by ARMSSE being used both as typedef and function-like macro
there. Converted manually.
Line breaks tidied up manually. One nested declaration of @local_err
deleted manually. Preexisting unwanted blank line dropped in
hw/riscv/sifive_e.c.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <20200707160613.848843-35-armbru@redhat.com>
The previous commit enables conversion of
qdev_prop_set_drive_err(..., &err);
if (err) {
...
}
to
if (!qdev_prop_set_drive_err(..., errp)) {
...
}
Coccinelle script:
@@
identifier fun = qdev_prop_set_drive_err;
expression list args;
typedef Error;
Error *err;
@@
- fun(args, &err);
- if (err)
+ if (!fun(args, &err))
{
...
}
One line break tidied up manually.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <20200707160613.848843-33-armbru@redhat.com>
The previous commit enables conversion of
foo(..., &err);
if (err) {
...
}
to
if (!foo(..., errp)) {
...
}
for QOM functions that now return true / false on success / error.
Coccinelle script:
@@
identifier fun = {
object_apply_global_props, object_initialize_child_with_props,
object_initialize_child_with_propsv, object_property_get,
object_property_get_bool, object_property_parse, object_property_set,
object_property_set_bool, object_property_set_int,
object_property_set_link, object_property_set_qobject,
object_property_set_str, object_property_set_uint, object_set_props,
object_set_propv, user_creatable_add_dict,
user_creatable_complete, user_creatable_del
};
expression list args, args2;
typedef Error;
Error *err;
@@
- fun(args, &err, args2);
- if (err)
+ if (!fun(args, &err, args2))
{
...
}
Fails to convert hw/arm/armsse.c, because Coccinelle gets confused by
ARMSSE being used both as typedef and function-like macro there.
Convert manually.
Line breaks tidied up manually.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-Id: <20200707160613.848843-29-armbru@redhat.com>
The object_property_set_FOO() setters take property name and value in
an unusual order:
void object_property_set_FOO(Object *obj, FOO_TYPE value,
const char *name, Error **errp)
Having to pass value before name feels grating. Swap them.
Same for object_property_set(), object_property_get(), and
object_property_parse().
Convert callers with this Coccinelle script:
@@
identifier fun = {
object_property_get, object_property_parse, object_property_set_str,
object_property_set_link, object_property_set_bool,
object_property_set_int, object_property_set_uint, object_property_set,
object_property_set_qobject
};
expression obj, v, name, errp;
@@
- fun(obj, v, name, errp)
+ fun(obj, name, v, errp)
Chokes on hw/arm/musicpal.c's lcd_refresh() with the unhelpful error
message "no position information". Convert that one manually.
Fails to convert hw/arm/armsse.c, because Coccinelle gets confused by
ARMSSE being used both as typedef and function-like macro there.
Convert manually.
Fails to convert hw/rx/rx-gdbsim.c, because Coccinelle gets confused
by RXCPU being used both as typedef and function-like macro there.
Convert manually. The other files using RXCPU that way don't need
conversion.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-Id: <20200707160613.848843-27-armbru@redhat.com>
[Straightforwad conflict with commit 2336172d9b "audio: set default
value for pcspk.iobase property" resolved]
Convert
foo(..., &err);
if (err) {
...
}
to
if (!foo(..., &err)) {
...
}
for qdev_realize(), qdev_realize_and_unref(), qbus_realize() and their
wrappers isa_realize_and_unref(), pci_realize_and_unref(),
sysbus_realize(), sysbus_realize_and_unref(), usb_realize_and_unref().
Coccinelle script:
@@
identifier fun = {
isa_realize_and_unref, pci_realize_and_unref, qbus_realize,
qdev_realize, qdev_realize_and_unref, sysbus_realize,
sysbus_realize_and_unref, usb_realize_and_unref
};
expression list args, args2;
typedef Error;
Error *err;
@@
- fun(args, &err, args2);
- if (err)
+ if (!fun(args, &err, args2))
{
...
}
Chokes on hw/arm/musicpal.c's lcd_refresh() with the unhelpful error
message "no position information". Nothing to convert there; skipped.
Fails to convert hw/arm/armsse.c, because Coccinelle gets confused by
ARMSSE being used both as typedef and function-like macro there.
Converted manually.
A few line breaks tidied up manually.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Message-Id: <20200707160613.848843-5-armbru@redhat.com>
The FROM_SSI_SLAVE() macro predates QOM and is used as a typesafe way
to cast from an SSISlave* to the instance struct of a subtype of
TYPE_SSI_SLAVE. Switch to using the QOM cast macros instead, which
have the same effect (by writing the QOM macros if the types were
previously missing them.)
(The FROM_SSI_SLAVE() macro allows the SSISlave member of the
subtype's struct to be anywhere as long as it is named "ssidev",
whereas a QOM cast macro insists that it is the first thing in the
subtype's struct. This is true for all the types we convert here.)
This removes all the uses of FROM_SSI_SLAVE() so we can delete the
definition.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20200628142429.17111-18-peter.maydell@linaro.org
milkymist_memcard_realize() leaks an Error object when realization of
its "sd-card" device fails. Quite harmless, since we only ever
realize this once, in milkymist_init() via milkymist_memcard_create().
Plug the leak.
Fixes: 3d0369ba49
Cc: Philippe Mathieu-Daudé <philmd@redhat.com>
Cc: Michael Walle <michael@walle.cc>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20200630090351.1247703-10-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
The Error ** argument must be NULL, &error_abort, &error_fatal, or a
pointer to a variable containing NULL. Passing an argument of the
latter kind twice without clearing it in between is wrong: if the
first call sets an error, it no longer points to NULL for the second
call.
milkymist_memcard_realize() is wrong that way: it passes &err to
qdev_prop_set_drive_err() and qdev_realize_and_unref(). Currently
harmless, because the latter uses it only as first argument of
error_propagate().
Making qdev_prop_set_drive_err() fail involves abuse of -global.
Leave handling that to qdev_prop_set_drive(), like we do elsewhere.
Cc: Michael Walle <michael@walle.cc>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20200622094227.1271650-17-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
On error, pxa2xx_mmci_init() reports to stderr and returns NULL.
Callers don't check for errors. Machines akita, borzoi, mainstone,
spitz, terrier, tosa, and z2 crash shortly after, like this:
$ qemu-system-aarch64 -M akita -drive if=sd,readonly=on
qemu-system-aarch64: failed to init SD card: Cannot use read-only drive as SD card
Segmentation fault (core dumped)
Machines connex and verdex reach the check for orphaned drives first:
$ aarch64-softmmu/qemu-system-aarch64 -M connex -drive if=sd,readonly=on -accel qtest
qemu-system-aarch64: failed to init SD card: Cannot use read-only drive as SD card
qemu-system-aarch64: -drive if=sd,readonly=on: machine type does not support if=sd,bus=0,unit=0
Make pxa2xx_mmci_init() fail cleanly right away.
Cc: Andrzej Zaborowski <balrogg@gmail.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: qemu-arm@nongnu.org
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200622094227.1271650-16-armbru@redhat.com>
qdev_prop_set_drive() can fail. None of the other qdev_prop_set_FOO()
can; they abort on error.
To clean up this inconsistency, rename qdev_prop_set_drive() to
qdev_prop_set_drive_err(), and create a qdev_prop_set_drive() that
aborts on error.
Coccinelle script to update callers:
@ depends on !(file in "hw/core/qdev-properties-system.c")@
expression dev, name, value;
symbol error_abort;
@@
- qdev_prop_set_drive(dev, name, value, &error_abort);
+ qdev_prop_set_drive(dev, name, value);
@@
expression dev, name, value, errp;
@@
- qdev_prop_set_drive(dev, name, value, errp);
+ qdev_prop_set_drive_err(dev, name, value, errp);
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200622094227.1271650-14-armbru@redhat.com>
The Linux kernel's IMX code now uses vendor specific commands.
This results in endless warnings when booting the Linux kernel.
sdhci-esdhc-imx 2194000.usdhc: esdhc_wait_for_card_clock_gate_off:
card clock still not gate off in 100us!.
Implement support for the vendor specific command implemented in IMX hardware
to be able to avoid this warning.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Message-id: 20200603145258.195920-2-linux@roeck-us.net
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This is still the same transformation as in the previous commits, but
here the sysbus_init_child_obj() and its matching realize in are in
separate files. Fortunately, there's just one realize left to
convert.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20200610053247.1583243-51-armbru@redhat.com>
This is the transformation explained in the commit before previous.
Takes care of just one pattern that needs conversion. More to come in
this series.
Coccinelle script:
@ depends on !(file in "hw/arm/highbank.c")@
expression bus, type_name, dev, expr;
@@
- dev = qdev_create(bus, type_name);
+ dev = qdev_new(type_name);
... when != dev = expr
- qdev_init_nofail(dev);
+ qdev_realize_and_unref(dev, bus, &error_fatal);
@@
expression bus, type_name, dev, expr;
identifier DOWN;
@@
- dev = DOWN(qdev_create(bus, type_name));
+ dev = DOWN(qdev_new(type_name));
... when != dev = expr
- qdev_init_nofail(DEVICE(dev));
+ qdev_realize_and_unref(DEVICE(dev), bus, &error_fatal);
@@
expression bus, type_name, expr;
identifier dev;
@@
- DeviceState *dev = qdev_create(bus, type_name);
+ DeviceState *dev = qdev_new(type_name);
... when != dev = expr
- qdev_init_nofail(dev);
+ qdev_realize_and_unref(dev, bus, &error_fatal);
@@
expression bus, type_name, dev, expr, errp;
symbol true;
@@
- dev = qdev_create(bus, type_name);
+ dev = qdev_new(type_name);
... when != dev = expr
- object_property_set_bool(OBJECT(dev), true, "realized", errp);
+ qdev_realize_and_unref(dev, bus, errp);
@@
expression bus, type_name, expr, errp;
identifier dev;
symbol true;
@@
- DeviceState *dev = qdev_create(bus, type_name);
+ DeviceState *dev = qdev_new(type_name);
... when != dev = expr
- object_property_set_bool(OBJECT(dev), true, "realized", errp);
+ qdev_realize_and_unref(dev, bus, errp);
The first rule exempts hw/arm/highbank.c, because it matches along two
control flow paths there, with different @type_name. Covered by the
next commit's manual conversions.
Missing #include "qapi/error.h" added manually.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20200610053247.1583243-10-armbru@redhat.com>
[Conflicts in hw/misc/empty_slot.c and hw/sparc/leon3.c resolved]
Commit 260bc9d8aa "hw/sd/sd.c: QOMify" QOMified only the device
itself, not its users. It kept sd_init() around for non-QOMified
users.
More than four years later, three such users remain: omap1 (machines
cheetah, sx1, sx1-v1) and omap2 (machines n800, n810) are not
QOMified, and pl181 (machines integratorcp, realview-eb,
realview-eb-mpcore, realview-pb-a8 realview-pbx-a9, versatileab,
versatilepb, vexpress-a15, vexpress-a9) is not QOMified properly.
The issue I presently have with this: an "sd-card" device should plug
into an "sd-bus" (its DeviceClass member bus_type says so), but
sd_init() leaves it unplugged. This is normally a bug (I just fixed
some instances), and I'd like to assert proper pluggedness to prevent
regressions. However, the qdev-but-not-quite thing returned by
sd_init() would fail the assertion. Meh.
Make sd_init() hide it from QOM/qdev. Visible in "info qom-tree",
here's the change for cheetah:
/machine (cheetah-machine)
[...]
/unattached (container)
[...]
/device[5] (serial-mm)
/serial (serial)
/serial[0] (qemu:memory-region)
- /device[6] (sd-card)
- /device[7] (omap-gpio)
+ /device[6] (omap-gpio)
[rest of device[*] renumbered...]
Cc: "Philippe Mathieu-Daudé" <philmd@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20200609122339.937862-24-armbru@redhat.com>
pxa2xx_mmci_init() creates a "pxa2xx-mmci" device, but neglects to
realize it. Affects machines akita, borzoi, connex, mainstone, spitz,
terrier, tosa, verdex, and z2.
In theory, a device becomes real only on realize. In practice, the
transition from unreal to real is a fuzzy one. The work to make a
device real can be spread between realize methods (fine),
instance_init methods (wrong), and board code wiring up the device
(fine as long as it effectively happens on realize). Depending on
what exactly is done where, a device can work even when we neglect
to realize it.
This one appears to work. Nevertheless, it's a clear misuse of the
interface. Even when it works today (more or less by chance), it can
break tomorrow.
Fix by realizing it right away. Visible in "info qom-tree"; here's
the change for akita:
/machine (akita-machine)
[...]
/unattached (container)
[...]
+ /device[5] (pxa2xx-mmci)
+ /pxa2xx-mmci[0] (qemu:memory-region)
+ /sd-bus (pxa2xx-mmci-bus)
[rest of device[*] renumbered...]
Fixes: 7a9468c925
Cc: Andrzej Zaborowski <balrogg@gmail.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: qemu-arm@nongnu.org
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20200609122339.937862-4-armbru@redhat.com>
Replace
error_report("...: %s", ..., error_get_pretty(err));
by
error_reportf_err(err, "...: ", ...);
One of the replaced messages lacked a colon. Add it.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200505101908.6207-6-armbru@redhat.com>
Devices may have component devices and buses.
Device realization may fail. Realization is recursive: a device's
realize() method realizes its components, and device_set_realized()
realizes its buses (which should in turn realize the devices on that
bus, except bus_set_realized() doesn't implement that, yet).
When realization of a component or bus fails, we need to roll back:
unrealize everything we realized so far. If any of these unrealizes
failed, the device would be left in an inconsistent state. Must not
happen.
device_set_realized() lets it happen: it ignores errors in the roll
back code starting at label child_realize_fail.
Since realization is recursive, unrealization must be recursive, too.
But how could a partly failed unrealize be rolled back? We'd have to
re-realize, which can fail. This design is fundamentally broken.
device_set_realized() does not roll back at all. Instead, it keeps
unrealizing, ignoring further errors.
It can screw up even for a device with no buses: if the lone
dc->unrealize() fails, it still unregisters vmstate, and calls
listeners' unrealize() callback.
bus_set_realized() does not roll back either. Instead, it stops
unrealizing.
Fortunately, no unrealize method can fail, as we'll see below.
To fix the design error, drop parameter @errp from all the unrealize
methods.
Any unrealize method that uses @errp now needs an update. This leads
us to unrealize() methods that can fail. Merely passing it to another
unrealize method cannot cause failure, though. Here are the ones that
do other things with @errp:
* virtio_serial_device_unrealize()
Fails when qbus_set_hotplug_handler() fails, but still does all the
other work. On failure, the device would stay realized with its
resources completely gone. Oops. Can't happen, because
qbus_set_hotplug_handler() can't actually fail here. Pass
&error_abort to qbus_set_hotplug_handler() instead.
* hw/ppc/spapr_drc.c's unrealize()
Fails when object_property_del() fails, but all the other work is
already done. On failure, the device would stay realized with its
vmstate registration gone. Oops. Can't happen, because
object_property_del() can't actually fail here. Pass &error_abort
to object_property_del() instead.
* spapr_phb_unrealize()
Fails and bails out when remove_drcs() fails, but other work is
already done. On failure, the device would stay realized with some
of its resources gone. Oops. remove_drcs() fails only when
chassis_from_bus()'s object_property_get_uint() fails, and it can't
here. Pass &error_abort to remove_drcs() instead.
Therefore, no unrealize method can fail before this patch.
device_set_realized()'s recursive unrealization via bus uses
object_property_set_bool(). Can't drop @errp there, so pass
&error_abort.
We similarly unrealize with object_property_set_bool() elsewhere,
always ignoring errors. Pass &error_abort instead.
Several unrealize methods no longer handle errors from other unrealize
methods: virtio_9p_device_unrealize(),
virtio_input_device_unrealize(), scsi_qdev_unrealize(), ...
Much of the deleted error handling looks wrong anyway.
One unrealize methods no longer ignore such errors:
usb_ehci_pci_exit().
Several realize methods no longer ignore errors when rolling back:
v9fs_device_realize_common(), pci_qdev_unrealize(),
spapr_phb_realize(), usb_qdev_realize(), vfio_ccw_realize(),
virtio_device_realize().
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20200505152926.18877-17-armbru@redhat.com>
Fixes the following coccinelle warnings:
$ spatch --sp-file --verbose-parsing ... \
scripts/coccinelle/remove_local_err.cocci
...
SUSPICIOUS: a \ character appears outside of a #define at ./target/ppc/translate_init.inc.c:5213
SUSPICIOUS: a \ character appears outside of a #define at ./target/ppc/translate_init.inc.c:5261
SUSPICIOUS: a \ character appears outside of a #define at ./target/microblaze/cpu.c:166
SUSPICIOUS: a \ character appears outside of a #define at ./target/microblaze/cpu.c:167
SUSPICIOUS: a \ character appears outside of a #define at ./target/microblaze/cpu.c:169
SUSPICIOUS: a \ character appears outside of a #define at ./target/microblaze/cpu.c:170
SUSPICIOUS: a \ character appears outside of a #define at ./target/microblaze/cpu.c:171
SUSPICIOUS: a \ character appears outside of a #define at ./target/microblaze/cpu.c:172
SUSPICIOUS: a \ character appears outside of a #define at ./target/microblaze/cpu.c:173
SUSPICIOUS: a \ character appears outside of a #define at ./target/i386/cpu.c:5787
SUSPICIOUS: a \ character appears outside of a #define at ./target/i386/cpu.c:5789
SUSPICIOUS: a \ character appears outside of a #define at ./target/i386/cpu.c:5800
SUSPICIOUS: a \ character appears outside of a #define at ./target/i386/cpu.c:5801
SUSPICIOUS: a \ character appears outside of a #define at ./target/i386/cpu.c:5802
SUSPICIOUS: a \ character appears outside of a #define at ./target/i386/cpu.c:5804
SUSPICIOUS: a \ character appears outside of a #define at ./target/i386/cpu.c:5805
SUSPICIOUS: a \ character appears outside of a #define at ./target/i386/cpu.c:5806
SUSPICIOUS: a \ character appears outside of a #define at ./target/i386/cpu.c:6329
SUSPICIOUS: a \ character appears outside of a #define at ./hw/sd/sdhci.c:1133
SUSPICIOUS: a \ character appears outside of a #define at ./hw/scsi/scsi-disk.c:3081
SUSPICIOUS: a \ character appears outside of a #define at ./hw/net/virtio-net.c:1529
SUSPICIOUS: a \ character appears outside of a #define at ./hw/riscv/sifive_u.c:468
SUSPICIOUS: a \ character appears outside of a #define at ./dump/dump.c:1895
SUSPICIOUS: a \ character appears outside of a #define at ./block/vhdx.c:2209
SUSPICIOUS: a \ character appears outside of a #define at ./block/vhdx.c:2215
SUSPICIOUS: a \ character appears outside of a #define at ./block/vhdx.c:2221
SUSPICIOUS: a \ character appears outside of a #define at ./block/vhdx.c:2222
SUSPICIOUS: a \ character appears outside of a #define at ./block/replication.c:172
SUSPICIOUS: a \ character appears outside of a #define at ./block/replication.c:173
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20200412223619.11284-2-f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
It's wrong to use same err object as errp parameter for several
function calls without intermediate checking for error: we'll crash if
try to set err object twice. Fix that.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-Id: <20200317125741.15301-1-vsementsov@virtuozzo.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
The Allwinner System on Chip families sun4i and above contain
an integrated storage controller for Secure Digital (SD) and
Multi Media Card (MMC) interfaces. This commit adds support
for the Allwinner SD/MMC storage controller with the following
emulated features:
* DMA transfers
* Direct FIFO I/O
* Short/Long format command responses
* Auto-Stop command (CMD12)
* Insert & remove card detection
The following boards are extended with the SD host controller:
* Cubieboard (hw/arm/cubieboard.c)
* Orange Pi PC (hw/arm/orangepi.c)
Signed-off-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20200311221854.30370-9-nieklinnenbank@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Since its introduction in commit d86a77f8ab, dma_memory_read()
always accepted void pointer argument. Remove the unnecessary
casts.
This commit was produced with the included Coccinelle script
scripts/coccinelle/exec_rw_const.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
---
v4: Drop parenthesis when removing cast (Eric Blake)
We have many files that apparently do not depend on the target CPU
configuration, i.e. which can be put into common-obj-y instead of
obj-y. This way, the code can be shared for example between
qemu-system-arm and qemu-system-aarch64, or the various big and
little endian variants like qemu-system-sh4 and qemu-system-sh4eb,
so that we do not have to compile the code multiple times anymore.
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20200130133841.10779-1-thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Provide a temporary device_legacy_reset function doing what
device_reset does to prepare for the transition with Resettable
API.
All occurrence of device_reset in the code tree are also replaced
by device_legacy_reset.
The new resettable API has different prototype and semantics
(resetting child buses as well as the specified device). Subsequent
commits will make the changeover for each call site individually; once
that is complete device_legacy_reset() will be removed.
Signed-off-by: Damien Hedde <damien.hedde@greensocs.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20200123132823.1117486-2-damien.hedde@greensocs.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The AST2600 includes a second cut-down version of the SD/MMC controller
found in the AST2500, named the eMMC controller. It's cut down in the
sense that it only supports one slot rather than two, but it brings the
total number of slots supported by the AST2600 to three.
The existing code assumed that the SD controller always provided two
slots. Rework the SDHCI object to expose the number of slots as a
property to be set by the SoC configuration.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20200114103433.30534-2-clg@kaod.org
[PMM: fixed up to use device_class_set_props()]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <20191205174635.18758-16-vsementsov@virtuozzo.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
This file keeps the various QDev blocks separated by comments.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Cleber Rosa <crosa@redhat.com>
Message-id: 20191005154748.21718-3-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Aspeed SOCs have two SD/MMC controllers. Add a device that
encapsulates both of these controllers and models the Aspeed-specific
registers and behavior.
Tested by reading from mmcblk0 in Linux:
qemu-system-arm -machine romulus-bmc -nographic \
-drive file=flash-romulus,format=raw,if=mtd \
-device sd-card,drive=sd0 -drive file=_tmp/kernel,format=raw,if=sd,id=sd0
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20190925143248.10000-3-clg@kaod.org
[clg: - changed the controller MMIO window size to 0x1000
- moved the MMIO mapping of the SDHCI slots at the SoC level
- merged code to add SD drives on the SD buses at the machine level ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
While the tracing framework does not forbid trailing newline in
events format string, using them lead to confuse output.
It is the responsibility of the backend to properly end an event
line.
Some of our formats have trailing newlines, remove them.
[Fixed typo in commit description reported by Eric Blake
<eblake@redhat.com>
--Stefan]
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190916095121.29506-2-philmd@redhat.com
Message-Id: <20190916095121.29506-2-philmd@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
In my "build everything" tree, changing sysemu/sysemu.h triggers a
recompile of some 5400 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).
Almost a third of its inclusions are actually superfluous. Delete
them. Downgrade two more to qapi/qapi-types-run-state.h, and move one
from char/serial.h to char/serial.c.
hw/semihosting/config.c, monitor/monitor.c, qdev-monitor.c, and
stubs/semihost.c define variables declared in sysemu/sysemu.h without
including it. The compiler is cool with that, but include it anyway.
This doesn't reduce actual use much, as it's still included into
widely included headers. The next commit will tackle that.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190812052359.30071-27-armbru@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
In my "build everything" tree, changing hw/qdev-properties.h triggers
a recompile of some 2700 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).
Many places including hw/qdev-properties.h (directly or via hw/qdev.h)
actually need only hw/qdev-core.h. Include hw/qdev-core.h there
instead.
hw/qdev.h is actually pointless: all it does is include hw/qdev-core.h
and hw/qdev-properties.h, which in turn includes hw/qdev-core.h.
Replace the remaining uses of hw/qdev.h by hw/qdev-properties.h.
While there, delete a few superfluous inclusions of hw/qdev-core.h.
Touching hw/qdev-properties.h now recompiles some 1200 objects.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Daniel P. Berrangé" <berrange@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20190812052359.30071-22-armbru@redhat.com>
In my "build everything" tree, changing hw/hw.h triggers a recompile
of some 2600 out of 6600 objects (not counting tests and objects that
don't depend on qemu/osdep.h).
The previous commits have left only the declaration of hw_error() in
hw/hw.h. This permits dropping most of its inclusions. Touching it
now recompiles less than 200 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190812052359.30071-19-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
In my "build everything" tree, changing migration/vmstate.h triggers a
recompile of some 2700 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).
hw/hw.h supposedly includes it for convenience. Several other headers
include it just to get VMStateDescription. The previous commit made
that unnecessary.
Include migration/vmstate.h only where it's still needed. Touching it
now recompiles only some 1600 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190812052359.30071-16-armbru@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
In my "build everything" tree, changing hw/irq.h triggers a recompile
of some 5400 out of 6600 objects (not counting tests and objects that
don't depend on qemu/osdep.h).
hw/hw.h supposedly includes it for convenience. Several other headers
include it just to get qemu_irq and.or qemu_irq_handler.
Move the qemu_irq and qemu_irq_handler typedefs from hw/irq.h to
qemu/typedefs.h, and then include hw/irq.h only where it's still
needed. Touching it now recompiles only some 500 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190812052359.30071-13-armbru@redhat.com>
Due to an off-by-one error, the assert statements allow an
out-of-bound array access. This doesn't happen in practice,
but the static analyzer notices.
Signed-off-by: Lidong Chen <lidong.chen@oracle.com>
Reviewed-by: Liam Merwick <liam.merwick@oracle.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Li Qiang <liq3ea@gmail.com>
Reviewed-by: Darren Kenny <darren.kenny@oracle.com>
Message-Id: <6b19cb7359a10a6bedc3ea0fce22fed3ef93c102.1560806687.git.lidong.chen@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Rather than looking inside the definition of a BusState with "s->bus.qbus",
use the QOM prefered style: "BUS(&s->bus)".
This patch was generated using the following Coccinelle script:
// Use BUS() macros to access BusState.qbus
@use_bus_macro_to_access_qbus@
expression obj;
identifier bus;
@@
-&obj->bus.qbus
+BUS(&obj->bus)
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20190528164020.32250-6-philmd@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Header guard symbols should match their file name to make guard
collisions less likely.
Cleaned up with scripts/clean-header-guards.pl, followed by some
renaming of new guard symbols picked by the script to better ones.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190315145123.28030-6-armbru@redhat.com>
[Rebase to master: update include/hw/net/ne2000-isa.h]
Tracked down with cleanup-trace-events.pl. Funnies requiring manual
post-processing:
* block.c and blockdev.c trace points are in block/trace-events.
* hw/block/nvme.c uses the preprocessor to hide its trace point use
from cleanup-trace-events.pl.
* include/hw/xen/xen_common.h trace points are in hw/xen/trace-events.
* net/colo-compare and net/filter-rewriter.c use pseudo trace points
colo_compare_udp_miscompare and colo_filter_rewriter_debug to guard
debug code.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-id: 20190314180929.27722-5-armbru@redhat.com
Message-Id: <20190314180929.27722-5-armbru@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
We spell out sub/dir/ in sub/dir/trace-events' comments pointing to
source files. That's because when trace-events got split up, the
comments were moved verbatim.
Delete the sub/dir/ part from these comments. Gets rid of several
misspellings.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190314180929.27722-3-armbru@redhat.com
Message-Id: <20190314180929.27722-3-armbru@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Some machines have an SDHCI device, but no PCI. To be able to
compile hw/sd/sdhci.c without CONFIG_PCI, we must not call functions
like pci_get_address_space() and pci_allocate_irq() there. Thus
move the PCI-related code into a separate file.
This is required for the new Kconfig-like build system, e.g. it is
needed if a user wants to compile a QEMU binary with just one machine
that has SDHCI, but no PCI, like the ARM "raspi" machines for example.
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
