instead of accessing tqe_prev field dircetly outside
of queue.h use macros to check if element is in list
and make sure that afer element is removed from list
tqe_prev field could be used to do the same check.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <1469450832-84343-1-git-send-email-imammedo@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The idea is simple - backup is "written-once" data. It is written block
by block and it is large enough. It would be nice to save storage
space and compress it.
Signed-off-by: Pavel Butsykin <pbutsykin@virtuozzo.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Denis V. Lunev <den@openvz.org>
CC: Jeff Cody <jcody@redhat.com>
CC: Markus Armbruster <armbru@redhat.com>
CC: Eric Blake <eblake@redhat.com>
CC: John Snow <jsnow@redhat.com>
CC: Stefan Hajnoczi <stefanha@redhat.com>
CC: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The idea is simple - backup is "written-once" data. It is written block
by block and it is large enough. It would be nice to save storage
space and compress it.
The patch adds a flag to the qmp/hmp drive-backup command which enables
block compression. Compression should be implemented in the format driver
to enable this feature.
There are some limitations of the format driver to allow compressed writes.
We can write data only once. Though for backup this is perfectly fine.
These limitations are maintained by the driver and the error will be
reported if we are doing something wrong.
Signed-off-by: Pavel Butsykin <pbutsykin@virtuozzo.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Denis V. Lunev <den@openvz.org>
CC: Jeff Cody <jcody@redhat.com>
CC: Markus Armbruster <armbru@redhat.com>
CC: Eric Blake <eblake@redhat.com>
CC: John Snow <jsnow@redhat.com>
CC: Stefan Hajnoczi <stefanha@redhat.com>
CC: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Now that we can support boxed commands, use it to greatly reduce the
number of parameters (and likelihood of getting out of sync) when
adjusting blockdev-backup parameters.
Signed-off-by: Pavel Butsykin <pbutsykin@virtuozzo.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Denis V. Lunev <den@openvz.org>
CC: Jeff Cody <jcody@redhat.com>
CC: Markus Armbruster <armbru@redhat.com>
CC: Eric Blake <eblake@redhat.com>
CC: John Snow <jsnow@redhat.com>
CC: Stefan Hajnoczi <stefanha@redhat.com>
CC: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Now that we can support boxed commands, use it to greatly reduce the
number of parameters (and likelihood of getting out of sync) when
adjusting drive-backup parameters.
Signed-off-by: Pavel Butsykin <pbutsykin@virtuozzo.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Denis V. Lunev <den@openvz.org>
CC: Jeff Cody <jcody@redhat.com>
CC: Markus Armbruster <armbru@redhat.com>
CC: Eric Blake <eblake@redhat.com>
CC: John Snow <jsnow@redhat.com>
CC: Stefan Hajnoczi <stefanha@redhat.com>
CC: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
In order to remove the necessity to use BlockBackend names in the
external API, we want to allow node-names everywhere. This converts
drive-mirror to accept a node-name without lifting the restriction that
we're operating at a root node.
In case of an invalid device name, the command returns the GenericError
error class now instead of DeviceNotFound, because this is what
qmp_get_root_bs() returns.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
In order to remove the necessity to use BlockBackend names in the
external API, we want to allow node-names everywhere. This converts
drive-backup and the corresponding transaction action to accept a
node-name without lifting the restriction that we're operating at a root
node.
In case of an invalid device name, the command returns the GenericError
error class now instead of DeviceNotFound, because this is what
qmp_get_root_bs() returns.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Alberto Garcia <berto@igalia.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
In order to remove the necessity to use BlockBackend names in the
external API, we want to allow node-names everywhere. This converts
change-backing-file to accept a node-name without lifting the
restriction that we're operating at a root node.
In case of an invalid device name, the command returns the GenericError
error class now instead of DeviceNotFound, because this is what
qmp_get_root_bs() returns.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Alberto Garcia <berto@igalia.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
In order to remove the necessity to use BlockBackend names in the
external API, we want to allow node-names everywhere. This converts
blockdev-snapshot-internal-sync to accept a node-name without lifting
the restriction that we're operating at a root node.
In case of an invalid device name, the command returns the GenericError
error class now instead of DeviceNotFound, because this is what
qmp_get_root_bs() returns.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Alberto Garcia <berto@igalia.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
In order to remove the necessity to use BlockBackend names in the
external API, we want to allow node-names everywhere. This converts
blockdev-snapshot-delete-internal-sync to accept a node-name without
lifting the restriction that we're operating at a root node.
In case of an invalid device name, the command returns the GenericError
error class now instead of DeviceNotFound, because this is what
qmp_get_root_bs() returns.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Alberto Garcia <berto@igalia.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
In order to remove the necessity to use BlockBackend names in the
external API, we want to allow node-names everywhere. This converts
blockdev-mirror to accept a node-name without lifting the restriction
that we're operating at a root node.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Alberto Garcia <berto@igalia.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
In order to remove the necessity to use BlockBackend names in the
external API, we want to allow node-names everywhere. This converts
blockdev-backup and the corresponding transaction action to accept a
node-name without lifting the restriction that we're operating at a root
node.
In case of an invalid device name, the command returns the GenericError
error class now instead of DeviceNotFound, because this is what
qmp_get_root_bs() returns.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
In order to remove the necessity to use BlockBackend names in the
external API, we want to allow node-names everywhere. This converts
block-commit to accept a node-name without lifting the restriction that
we're operating at a root node.
As libvirt makes use of the DeviceNotFound error class, we must add
explicit code to retain this behaviour because qmp_get_root_bs() only
returns GenericErrors.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Alberto Garcia <berto@igalia.com>
In order to remove the necessity to use BlockBackend names in the
external API, we want to allow node-names everywhere. This converts
block-stream to accept a node-name without lifting the restriction that
we're operating at a root node.
In case of an invalid device name, the command returns the GenericError
error class now instead of DeviceNotFound, because this is what
qmp_get_root_bs() returns.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Alberto Garcia <berto@igalia.com>
Commit 0d978913 changed blockdev-backup to accept arbitrary node names
instead of device names (i.e. root nodes) for the backup target.
However, it forgot to make the same change in transactions and to update
the documentation. This patch fixes these omissions.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Now that we can support boxed commands, use it to greatly
reduce the number of parameters (and likelihood of getting
out of sync) when adjusting drive-mirror parameters.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Message-Id: <1468535878-3760-1-git-send-email-eblake@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Now that we can support boxed commands, use it to greatly
reduce the number of parameters (and likelihood of getting
out of sync) when adjusting throttle parameters.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Alberto Garcia <berto@igalia.com>
Message-Id: <1468468228-27827-11-git-send-email-eblake@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
When I/O limits are set for a block device, the name of the throttling
group is taken from the BlockBackend if the user doesn't specify one.
Commit efaa7c4eeb moved the naming of the BlockBackend in
blockdev_init() to the end of the function, after I/O limits are set.
The consequence is that the throttling group gets an empty name.
Signed-off-by: Alberto Garcia <berto@igalia.com>
Reported-by: Stefan Hajnoczi <stefanha@redhat.com>
Cc: Max Reitz <mreitz@redhat.com>
Cc: qemu-stable@nongnu.org
Message-id: af5cd58bd2c4b9f6c57f260d9cfe586b9fb7d34d.1467986342.git.berto@igalia.com
[mreitz: Use existing "id" variable instead of new "blk_id"]
Signed-off-by: Max Reitz <mreitz@redhat.com>
This patch adds a new optional 'job-id' parameter to 'block-commit',
allowing the user to specify the ID of the block job to be created.
Signed-off-by: Alberto Garcia <berto@igalia.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This patch adds a new optional 'job-id' parameter to 'block-stream',
allowing the user to specify the ID of the block job to be created.
The HMP 'block_stream' command remains unchanged.
Signed-off-by: Alberto Garcia <berto@igalia.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This patch adds a new optional 'job-id' parameter to 'blockdev-backup'
and 'drive-backup', allowing the user to specify the ID of the block
job to be created.
The HMP 'drive_backup' command remains unchanged.
Signed-off-by: Alberto Garcia <berto@igalia.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This patch adds a new optional 'job-id' parameter to 'blockdev-mirror'
and 'drive-mirror', allowing the user to specify the ID of the block
job to be created.
The HMP 'drive_mirror' command remains unchanged.
Signed-off-by: Alberto Garcia <berto@igalia.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
find_block_job() looks for a block backend with a specified name,
checks whether it has a block job and acquires its AioContext.
We want to identify jobs by their ID and not by the block backend
they're attached to, so this patch ignores the backends altogether and
gets the job directly. Apart from making the code simpler, this will
allow us to find block jobs once they start having user-specified IDs.
To ensure backward compatibility we keep ERROR_CLASS_DEVICE_NOT_ACTIVE
as the error class if the job doesn't exist. In subsequent patches
we'll also need to keep the device name as the default job ID if the
user doesn't specify a different one.
Signed-off-by: Alberto Garcia <berto@igalia.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Making each output visitor provide its own output collection
function was the only remaining reason for exposing visitor
sub-types to the rest of the code base. Add a polymorphic
visit_complete() function which is a no-op for input visitors,
and which populates an opaque pointer for output visitors. For
maximum type-safety, also add a parameter to the output visitor
constructors with a type-correct version of the output pointer,
and assert that the two uses match.
This approach was considered superior to either passing the
output parameter only during construction (action at a distance
during visit_free() feels awkward) or only during visit_complete()
(defeating type safety makes it easier to use incorrectly).
Most callers were function-local, and therefore a mechanical
conversion; the testsuite was a bit trickier, but the previous
cleanup patch minimized the churn here.
The visit_complete() function may be called at most once; doing
so lets us use transfer semantics rather than duplication or
ref-count semantics to get the just-built output back to the
caller, even though it means our behavior is not idempotent.
Generated code is simplified as follows for events:
|@@ -26,7 +26,7 @@ void qapi_event_send_acpi_device_ost(ACP
| QDict *qmp;
| Error *err = NULL;
| QMPEventFuncEmit emit;
|- QmpOutputVisitor *qov;
|+ QObject *obj;
| Visitor *v;
| q_obj_ACPI_DEVICE_OST_arg param = {
| info
|@@ -39,8 +39,7 @@ void qapi_event_send_acpi_device_ost(ACP
|
| qmp = qmp_event_build_dict("ACPI_DEVICE_OST");
|
|- qov = qmp_output_visitor_new();
|- v = qmp_output_get_visitor(qov);
|+ v = qmp_output_visitor_new(&obj);
|
| visit_start_struct(v, "ACPI_DEVICE_OST", NULL, 0, &err);
| if (err) {
|@@ -55,7 +54,8 @@ void qapi_event_send_acpi_device_ost(ACP
| goto out;
| }
|
|- qdict_put_obj(qmp, "data", qmp_output_get_qobject(qov));
|+ visit_complete(v, &obj);
|+ qdict_put_obj(qmp, "data", obj);
| emit(QAPI_EVENT_ACPI_DEVICE_OST, qmp, &err);
and for commands:
| {
| Error *err = NULL;
|- QmpOutputVisitor *qov = qmp_output_visitor_new();
| Visitor *v;
|
|- v = qmp_output_get_visitor(qov);
|+ v = qmp_output_visitor_new(ret_out);
| visit_type_AddfdInfo(v, "unused", &ret_in, &err);
|- if (err) {
|- goto out;
|+ if (!err) {
|+ visit_complete(v, ret_out);
| }
|- *ret_out = qmp_output_get_qobject(qov);
|-
|-out:
| error_propagate(errp, err);
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <1465490926-28625-13-git-send-email-eblake@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Now that we have a polymorphic visit_free(), we no longer need
qmp_output_visitor_cleanup(); however, we still need to
expose the subtype for qmp_output_get_qobject().
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <1465490926-28625-10-git-send-email-eblake@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
error_propagate() already ignores local_err==NULL, so there's no
need to check it before calling.
Coccinelle patch used to perform the changes added to
scripts/coccinelle/error_propagate_null.cocci.
Reviewed-by: Eric Blake <eblake@redhat.com>
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <1465855078-19435-2-git-send-email-ehabkost@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
The QMP block-job-resume command and cancellation may want to reset the
job's iostatus. The next patches add a user who does not want to reset
iostatus so move it up to block_job_enter() callers.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-id: 1466096189-6477-2-git-send-email-stefanha@redhat.com
Currently, we are trying to move the backing BDS from the source to the
target in bdrv_replace_in_backing_chain() which is called from
mirror_exit(). However, mirror_complete() already tries to open the
target's backing chain with a call to bdrv_open_backing_file().
First, we should only set the target's backing BDS once. Second, the
mirroring block job has a better idea of what to set it to than the
generic code in bdrv_replace_in_backing_chain() (in fact, the latter's
conditions on when to move the backing BDS from source to target are not
really correct).
Therefore, remove that code from bdrv_replace_in_backing_chain() and
leave it to mirror_complete().
Depending on what kind of mirroring is performed, we furthermore want to
use different strategies to open the target's backing chain:
- If blockdev-mirror is used, we can assume the user made sure that the
target already has the correct backing chain. In particular, we should
not try to open a backing file if the target does not have any yet.
- If drive-mirror with mode=absolute-paths is used, we can and should
reuse the already existing chain of nodes that the source BDS is in.
In case of sync=full, no backing BDS is required; with sync=top, we
just link the source's backing BDS to the target, and with sync=none,
we use the source BDS as the target's backing BDS.
We should not try to open these backing files anew because this would
lead to two BDSs existing per physical file in the backing chain, and
we would like to avoid such concurrent access.
- If drive-mirror with mode=existing is used, we have to use the
information provided in the physical image file which means opening
the target's backing chain completely anew, just as it has been done
already.
If the target's backing chain shares images with the source, this may
lead to multiple BDSs per physical image file. But since we cannot
reliably ascertain this case, there is nothing we can do about it.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Message-id: 20160610185750.30956-3-mreitz@redhat.com
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
qmp_query_block_jobs() uses bdrv_next() to look for block jobs, but
this function can only find those in top-level BlockDriverStates.
This patch uses block_job_next() instead.
Signed-off-by: Alberto Garcia <berto@igalia.com>
Message-id: a8b7e5497b7c1fa67c12fcceae1630d01c3b1f96.1464346103.git.berto@igalia.com
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
When opening a device with a locked tray, gives an error explaining the
device tray is locked and that the user should wait and try again. This
is less confusing than the previous error, which simply stated that the
tray was locked.
Signed-off-by: Colin Lord <clord@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Returns negative error codes and accompanying error messages in cases where
the device has no tray or the tray is locked and isn't forced open. This
extra information should result in better flexibility in functions that
call do_open_tray.
Suggested by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Colin Lord <clord@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
If the BDS is attached, it will want to stay on the AioContext where its
BlockBackend is. Don't call bdrv_set_aio_context in this case.
Signed-off-by: Fam Zheng <famz@redhat.com>
Message-id: 1463969978-24970-3-git-send-email-famz@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
This allows backing up to a BDS that has not been attached to any BB.
Signed-off-by: Fam Zheng <famz@redhat.com>
Message-id: 1463969978-24970-2-git-send-email-famz@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
This changes the backup block job to use the job's BlockBackend for
performing its I/O. job->bs isn't used by the backup code any more
afterwards.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
This changes the mirror block job to use the job's BlockBackend for
performing its I/O. job->bs isn't used by the mirroring code any more
afterwards.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
We had to forbid mirroring to a target BDS that already had a BB
attached because the node swapping at job completion would add a second
BB and we didn't support multiple BBs on a single BDS at the time. Now
we do, so we can lift the restriction.
As we allow additional BlockBackends for the target, we must expect
other users to be sending requests. There may no requests be in flight
during the graph modification, so we have to drain those users now.
The core part of this patch is a revert of commit 40365552.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
blk_new() cannot fail so its Error ** parameter has become superfluous.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
There are no callers to bdrv_open() or bdrv_open_inherit() left that
pass a pointer to a non-NULL BDS pointer as the first argument of these
functions, so we can finally drop that parameter and just make them
return the new BDS.
Generally, the following pattern is applied:
bs = NULL;
ret = bdrv_open(&bs, ..., &local_err);
if (ret < 0) {
error_propagate(errp, local_err);
...
}
by
bs = bdrv_open(..., errp);
if (!bs) {
ret = -EINVAL;
...
}
Of course, there are only a few instances where the pattern is really
pure.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The bdrv_next() users all leaked the BdrvNextIterator after completing
the iteration. Simply changing bdrv_next() to free the iterator before
returning NULL at the end of list doesn't work because some callers exit
the loop before looking at all BDSes.
This patch moves the BdrvNextIterator from the heap to the stack of
the caller and switches to a bdrv_first()/bdrv_next() interface for
initialising the iterator.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
If you use HMP's eject but the CDROM tray is locked, you may get a
confusing error message informing you that the "tray isn't open."
As this is the point of eject, we can do a little better and help
clarify that the tray was locked and that it (might) open up later,
so try again.
It's not ideal, but it makes the semantics of the (legacy) eject
command more understandable to end users when they try to use it.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This patch removes the remaining users of bs->blk, which will allow us
to have multiple BBs on top of a single BDS. In the meantime, all checks
that are currently in place to prevent the user from creating such
setups can be switched to bdrv_has_blk() instead of accessing BDS.blk.
Future patches can allow them and e.g. enable users to mirror to a block
device that already has a BlockBackend on it.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
We need to introduce a separate BdrvNextIterator struct that can keep
more state than just the current BDS in order to avoid using the bs->blk
pointer.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
This reverts commit 76b223200e.
Now that I/O throttling is fully done on the BlockBackend level, there
is no reason any more to block I/O throttling for nodes with multiple
parents as the parents don't influence each other any more.
Conflicts:
block.c
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Alberto Garcia <berto@igalia.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
This moves the throttling related part of the BDS life cycle management
to BlockBackend. The throttling group reference is now kept even when no
medium is inserted.
With this commit, throttling isn't disabled and then re-enabled any more
during graph reconfiguration. This fixes the temporary breakage of I/O
throttling when used with live snapshots or block jobs that manipulate
the graph.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Alberto Garcia <berto@igalia.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
This patch changes where the throttling state is stored (used to be the
BlockDriverState, now it is the BlockBackend), but it doesn't actually
make it a BB level feature yet. For example, throttling is still
disabled when the BDS is detached from the BB.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
It was already true in principle that a throttled BDS always has a BB
attached, except that the order of operations while attaching or
detaching a BDS to/from a BB wasn't careful enough.
This commit breaks graph manipulations while I/O throttling is enabled.
It would have been possible to keep things working with some temporary
hacks, but quite cumbersome, so it's not worth the hassle. We'll fix
things again in a minute.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Alberto Garcia <berto@igalia.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
The new QMP command name is x-blockdev-change. It's just for adding/removing
quorum's child now, and doesn't support all kinds of children, all kinds of
operations, nor all block drivers. So it is experimental now.
Signed-off-by: Wen Congyang <wency@cn.fujitsu.com>
Signed-off-by: zhanghailiang <zhang.zhanghailiang@huawei.com>
Signed-off-by: Gonglei <arei.gonglei@huawei.com>
Signed-off-by: Changlong Xie <xiecl.fnst@cn.fujitsu.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Alberto Garcia <berto@igalia.com>
Message-id: 1462865799-19402-4-git-send-email-xiecl.fnst@cn.fujitsu.com
Signed-off-by: Max Reitz <mreitz@redhat.com>