Add property memory region which can connect with IOMMU region to support SMMU translate.
Signed-off-by: Jianxian Wen <jianxian.wen@verisilicon.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 4C23C17B8E87E74E906A25A3254A03F4FA1FEC31@SHASXM03.verisilicon.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
It's an ADC, put it where it belongs.
Cc: Edgar E. Iglesias <edgar.iglesias@gmail.com>
Cc: Alistair Francis <alistair@alistair23.me>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: qemu-arm@nongnu.org
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Commit dfc388797c ("hw/arm: xlnx: Set all boards' GEM 'phy-addr'
property value to 23") configured the PHY address for xilinx-zynq-a9
to 23. When trying to boot xilinx-zynq-a9 with zynq-zc702.dtb or
zynq-zc706.dtb, this results in the following error message when
trying to use the Ethernet interface.
macb e000b000.ethernet eth0: Could not attach PHY (-19)
The devicetree files for ZC702 and ZC706 configure PHY address 7. The
documentation for the ZC702 and ZC706 evaluation boards suggest that the
PHY address is 7, not 23. Other boards use PHY address 0, 1, 3, or 7.
I was unable to find a documentation or a devicetree file suggesting
or using PHY address 23. The Ethernet interface starts working with
zynq-zc702.dtb and zynq-zc706.dtb when setting the PHY address to 7,
so let's use it.
Cc: Bin Meng <bin.meng@windriver.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20210504124140.1100346-1-linux@roeck-us.net
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Stop including exec/address-spaces.h in files that don't need it.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20210416171314.2074665-5-thuth@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Several QOM type names contain ',':
ARM,bitband-memory
etraxfs,pic
etraxfs,serial
etraxfs,timer
fsl,imx25
fsl,imx31
fsl,imx6
fsl,imx6ul
fsl,imx7
grlib,ahbpnp
grlib,apbpnp
grlib,apbuart
grlib,gptimer
grlib,irqmp
qemu,register
SUNW,bpp
SUNW,CS4231
SUNW,DBRI
SUNW,DBRI.prom
SUNW,fdtwo
SUNW,sx
SUNW,tcx
xilinx,zynq_slcr
xlnx,zynqmp
xlnx,zynqmp-pmu-soc
xlnx,zynq-xadc
These are all device types. They can't be plugged with -device /
device_add, except for xlnx,zynqmp-pmu-soc, and I doubt that one
actually works.
They *can* be used with -device / device_add to request help.
Usability is poor, though: you have to double the comma, like this:
$ qemu-system-x86_64 -device SUNW,,fdtwo,help
Trap for the unwary. The fact that this was broken in
device-introspect-test for more than six years until commit e27bd49876
fixed it demonstrates that "the unwary" includes seasoned developers.
One QOM type name contains ' ': "ICH9 SMB". Because having to
remember just one way to quote would be too easy.
Rename the "SUNW,FOO types to "sun-FOO". Summarily replace ',' and '
' by '-' in the other type names.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20210304140229.575481-2-armbru@redhat.com>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
When debugging QEMU it is often useful to put a breakpoint on the
error_setg_internal method impl.
Unfortunately the object_property_add / object_class_property_add
methods call object_property_find / object_class_property_find methods
to check if a property exists already before adding the new property.
As a result there are a huge number of calls to error_setg_internal
on startup of most QEMU commands, making it very painful to set a
breakpoint on this method.
Most callers of object_find_property and object_class_find_property,
however, pass in a NULL for the Error parameter. This simplifies the
methods to remove the Error parameter entirely, and then adds some
new wrapper methods that are able to raise an Error when needed.
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200914135617.1493072-1-berrange@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
- Fixes a bug in printing trap causes
- Allows 16-bit writes to the SiFive test device. This fixes the
failure to reboot the RISC-V virt machine
- Support for the Microchip PolarFire SoC and Icicle Kit
- A reafactor of RISC-V code out of hw/riscv
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEE9sSsRtSTSGjTuM6PIeENKd+XcFQFAl9aa4YACgkQIeENKd+X
cFTJjgf5ASfFIO5HqP1l80/UM5Pswyq0IROZDq0ItZa6U4EPzLXoE2N0POriIj4h
Ds2JbMg0ORDqY0VbSxHlgYHMgJ9S6cuVOMnATsPG0d2jaJ3gSxLBu5k/1ENqe+Vw
sSYXZv5uEAUfOFz99zbuhKHct5HzlmBFW9dVHdflUQS+cRgsSXq27mz1BvZ8xMWl
lMhwubqdoNx0rOD3vKnlwrxaf54DcJ2IQT3BtTCjEar3tukdNaLijAuwt2hrFyr+
IwpeFXA/NWar+mXP3M+BvcLaI33j73/ac2+S5SJuzHGp/ot5nT5gAuq3PDEjHMeS
t6z9Exp776VXxNE2iUA5NB65Yp3/6w==
=07oA
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/alistair/tags/pull-riscv-to-apply-20200910' into staging
This PR includes multiple fixes and features for RISC-V:
- Fixes a bug in printing trap causes
- Allows 16-bit writes to the SiFive test device. This fixes the
failure to reboot the RISC-V virt machine
- Support for the Microchip PolarFire SoC and Icicle Kit
- A reafactor of RISC-V code out of hw/riscv
# gpg: Signature made Thu 10 Sep 2020 19:08:06 BST
# gpg: using RSA key F6C4AC46D4934868D3B8CE8F21E10D29DF977054
# gpg: Good signature from "Alistair Francis <alistair@alistair23.me>" [full]
# Primary key fingerprint: F6C4 AC46 D493 4868 D3B8 CE8F 21E1 0D29 DF97 7054
* remotes/alistair/tags/pull-riscv-to-apply-20200910: (30 commits)
hw/riscv: Sort the Kconfig options in alphabetical order
hw/riscv: Drop CONFIG_SIFIVE
hw/riscv: Always build riscv_hart.c
hw/riscv: Move sifive_test model to hw/misc
hw/riscv: Move sifive_uart model to hw/char
hw/riscv: Move riscv_htif model to hw/char
hw/riscv: Move sifive_plic model to hw/intc
hw/riscv: Move sifive_clint model to hw/intc
hw/riscv: Move sifive_gpio model to hw/gpio
hw/riscv: Move sifive_u_otp model to hw/misc
hw/riscv: Move sifive_u_prci model to hw/misc
hw/riscv: Move sifive_e_prci model to hw/misc
hw/riscv: sifive_u: Connect a DMA controller
hw/riscv: clint: Avoid using hard-coded timebase frequency
hw/riscv: microchip_pfsoc: Hook GPIO controllers
hw/riscv: microchip_pfsoc: Connect 2 Cadence GEMs
hw/arm: xlnx: Set all boards' GEM 'phy-addr' property value to 23
hw/net: cadence_gem: Add a new 'phy-addr' property
hw/riscv: microchip_pfsoc: Connect a DMA controller
hw/dma: Add SiFive platform DMA controller emulation
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
# Conflicts:
# hw/riscv/trace-events
When cadence_gem model was created for Xilinx boards, the PHY address
was hard-coded to 23 in the GEM model. Now that we have introduced a
property we can use that to tell GEM model what our PHY address is.
Change all boards' GEM 'phy-addr' property value to 23, and set the
PHY address default value to 0 in the GEM model.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1598924352-89526-13-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Some typedefs and macros are defined after the type check macros.
This makes it difficult to automatically replace their
definitions with OBJECT_DECLARE_TYPE.
Patch generated using:
$ ./scripts/codeconverter/converter.py -i \
--pattern=QOMStructTypedefSplit $(git grep -l '' -- '*.[ch]')
which will split "typdef struct { ... } TypedefName"
declarations.
Followed by:
$ ./scripts/codeconverter/converter.py -i --pattern=MoveSymbols \
$(git grep -l '' -- '*.[ch]')
which will:
- move the typedefs and #defines above the type check macros
- add missing #include "qom/object.h" lines if necessary
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20200831210740.126168-9-ehabkost@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20200831210740.126168-10-ehabkost@redhat.com>
Message-Id: <20200831210740.126168-11-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Clock canonical name is set in device_set_realized (see the block
added to hw/core/qdev.c in commit 0e6934f264).
If we connect a clock after the device is realized, this code is
not executed. This is currently not a problem as this name is only
used for trace events, however this disrupt tracing.
Fix by calling qdev_connect_clock_in() before realizing.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20200803105647.22223-3-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
As we want to call qdev_connect_clock_in() before the device
is realized, we need to uninline cadence_uart_create() first.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20200803105647.22223-2-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The object_property_set_FOO() setters take property name and value in
an unusual order:
void object_property_set_FOO(Object *obj, FOO_TYPE value,
const char *name, Error **errp)
Having to pass value before name feels grating. Swap them.
Same for object_property_set(), object_property_get(), and
object_property_parse().
Convert callers with this Coccinelle script:
@@
identifier fun = {
object_property_get, object_property_parse, object_property_set_str,
object_property_set_link, object_property_set_bool,
object_property_set_int, object_property_set_uint, object_property_set,
object_property_set_qobject
};
expression obj, v, name, errp;
@@
- fun(obj, v, name, errp)
+ fun(obj, name, v, errp)
Chokes on hw/arm/musicpal.c's lcd_refresh() with the unhelpful error
message "no position information". Convert that one manually.
Fails to convert hw/arm/armsse.c, because Coccinelle gets confused by
ARMSSE being used both as typedef and function-like macro there.
Convert manually.
Fails to convert hw/rx/rx-gdbsim.c, because Coccinelle gets confused
by RXCPU being used both as typedef and function-like macro there.
Convert manually. The other files using RXCPU that way don't need
conversion.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-Id: <20200707160613.848843-27-armbru@redhat.com>
[Straightforwad conflict with commit 2336172d9b "audio: set default
value for pcspk.iobase property" resolved]
qdev_prop_set_drive() can fail. None of the other qdev_prop_set_FOO()
can; they abort on error.
To clean up this inconsistency, rename qdev_prop_set_drive() to
qdev_prop_set_drive_err(), and create a qdev_prop_set_drive() that
aborts on error.
Coccinelle script to update callers:
@ depends on !(file in "hw/core/qdev-properties-system.c")@
expression dev, name, value;
symbol error_abort;
@@
- qdev_prop_set_drive(dev, name, value, &error_abort);
+ qdev_prop_set_drive(dev, name, value);
@@
expression dev, name, value, errp;
@@
- qdev_prop_set_drive(dev, name, value, errp);
+ qdev_prop_set_drive_err(dev, name, value, errp);
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200622094227.1271650-14-armbru@redhat.com>
All remaining conversions to qdev_realize() are for bus-less devices.
Coccinelle script:
// only correct for bus-less @dev!
@@
expression errp;
expression dev;
@@
- qdev_init_nofail(dev);
+ qdev_realize(dev, NULL, &error_fatal);
@ depends on !(file in "hw/core/qdev.c") && !(file in "hw/core/bus.c")@
expression errp;
expression dev;
symbol true;
@@
- object_property_set_bool(OBJECT(dev), true, "realized", errp);
+ qdev_realize(DEVICE(dev), NULL, errp);
@ depends on !(file in "hw/core/qdev.c") && !(file in "hw/core/bus.c")@
expression errp;
expression dev;
symbol true;
@@
- object_property_set_bool(dev, true, "realized", errp);
+ qdev_realize(DEVICE(dev), NULL, errp);
Note that Coccinelle chokes on ARMSSE typedef vs. macro in
hw/arm/armsse.c. Worked around by temporarily renaming the macro for
the spatch run.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20200610053247.1583243-57-armbru@redhat.com>
This is the transformation explained in the commit before previous.
Takes care of just one pattern that needs conversion. More to come in
this series.
Coccinelle script:
@ depends on !(file in "hw/arm/highbank.c")@
expression bus, type_name, dev, expr;
@@
- dev = qdev_create(bus, type_name);
+ dev = qdev_new(type_name);
... when != dev = expr
- qdev_init_nofail(dev);
+ qdev_realize_and_unref(dev, bus, &error_fatal);
@@
expression bus, type_name, dev, expr;
identifier DOWN;
@@
- dev = DOWN(qdev_create(bus, type_name));
+ dev = DOWN(qdev_new(type_name));
... when != dev = expr
- qdev_init_nofail(DEVICE(dev));
+ qdev_realize_and_unref(DEVICE(dev), bus, &error_fatal);
@@
expression bus, type_name, expr;
identifier dev;
@@
- DeviceState *dev = qdev_create(bus, type_name);
+ DeviceState *dev = qdev_new(type_name);
... when != dev = expr
- qdev_init_nofail(dev);
+ qdev_realize_and_unref(dev, bus, &error_fatal);
@@
expression bus, type_name, dev, expr, errp;
symbol true;
@@
- dev = qdev_create(bus, type_name);
+ dev = qdev_new(type_name);
... when != dev = expr
- object_property_set_bool(OBJECT(dev), true, "realized", errp);
+ qdev_realize_and_unref(dev, bus, errp);
@@
expression bus, type_name, expr, errp;
identifier dev;
symbol true;
@@
- DeviceState *dev = qdev_create(bus, type_name);
+ DeviceState *dev = qdev_new(type_name);
... when != dev = expr
- object_property_set_bool(OBJECT(dev), true, "realized", errp);
+ qdev_realize_and_unref(dev, bus, errp);
The first rule exempts hw/arm/highbank.c, because it matches along two
control flow paths there, with different @type_name. Covered by the
next commit's manual conversions.
Missing #include "qapi/error.h" added manually.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20200610053247.1583243-10-armbru@redhat.com>
[Conflicts in hw/misc/empty_slot.c and hw/sparc/leon3.c resolved]
The only way object_property_add() can fail is when a property with
the same name already exists. Since our property names are all
hardcoded, failure is a programming error, and the appropriate way to
handle it is passing &error_abort.
Same for its variants, except for object_property_add_child(), which
additionally fails when the child already has a parent. Parentage is
also under program control, so this is a programming error, too.
We have a bit over 500 callers. Almost half of them pass
&error_abort, slightly fewer ignore errors, one test case handles
errors, and the remaining few callers pass them to their own callers.
The previous few commits demonstrated once again that ignoring
programming errors is a bad idea.
Of the few ones that pass on errors, several violate the Error API.
The Error ** argument must be NULL, &error_abort, &error_fatal, or a
pointer to a variable containing NULL. Passing an argument of the
latter kind twice without clearing it in between is wrong: if the
first call sets an error, it no longer points to NULL for the second
call. ich9_pm_add_properties(), sparc32_ledma_realize(),
sparc32_dma_realize(), xilinx_axidma_realize(), xilinx_enet_realize()
are wrong that way.
When the one appropriate choice of argument is &error_abort, letting
users pick the argument is a bad idea.
Drop parameter @errp and assert the preconditions instead.
There's one exception to "duplicate property name is a programming
error": the way object_property_add() implements the magic (and
undocumented) "automatic arrayification". Don't drop @errp there.
Instead, rename object_property_add() to object_property_try_add(),
and add the obvious wrapper object_property_add().
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20200505152926.18877-15-armbru@redhat.com>
[Two semantic rebase conflicts resolved]
Add the connection between the slcr's output clocks and the uarts inputs.
Also add the main board clock 'ps_clk', which is hard-coded to 33.33MHz
(the default frequency). This clock is used to feed the slcr's input
clock.
Signed-off-by: Damien Hedde <damien.hedde@greensocs.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20200406135251.157596-9-damien.hedde@greensocs.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
USB ports on Xilinx Zync must be instantiated as TYPE_CHIPIDEA to work.
Linux expects and checks various chipidea registers, which do not exist
with the basic ehci emulation. This patch series fixes the problem.
Without this patch, USB ports fail to instantiate under Linux.
ci_hdrc ci_hdrc.0: doesn't support host
ci_hdrc ci_hdrc.0: no supported roles
With this patch, USB ports are instantiated, and it is possible
to boot from USB drive.
ci_hdrc ci_hdrc.0: EHCI Host Controller
ci_hdrc ci_hdrc.0: new USB bus registered, assigned bus number 1
ci_hdrc ci_hdrc.0: USB 2.0 started, EHCI 1.00
usb 1-1: new full-speed USB device number 2 using ci_hdrc
usb 1-1: not running at top speed; connect to a high speed hub
usb 1-1: config 1 interface 0 altsetting 0 endpoint 0x81 has invalid maxpacket 512, setting to 64
usb 1-1: config 1 interface 0 altsetting 0 endpoint 0x2 has invalid maxpacket 512, setting to 64
usb-storage 1-1:1.0: USB Mass Storage device detected
scsi host0: usb-storage 1-1:1.0
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20200215122354.13706-2-linux@roeck-us.net
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
memory_region_allocate_system_memory() API is going away, so
replace it with memdev allocated MemoryRegion. The later is
initialized by generic code, so board only needs to opt in
to memdev scheme by providing
MachineClass::default_ram_id
and using MachineState::ram instead of manually initializing
RAM memory region.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20200219160953.13771-36-imammedo@redhat.com>
If user provided non-sense RAM size, board will complain and
continue running with max RAM size supported.
Also RAM is going to be allocated by generic code, so it won't be
possible for board to fix things up for user.
Make it error message and exit to force user fix CLI,
instead of accepting non-sense CLI values.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200219160953.13771-35-imammedo@redhat.com>
IEC binary prefixes ease code review: the unit is explicit.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20191021190653.9511-2-philmd@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In struct arm_boot_info, kernel_filename, initrd_filename and
kernel_cmdline are copied from from MachineState. This patch add
MachineState as a parameter into arm_load_dtb() and move the copy chunk
of kernel_filename, initrd_filename and kernel_cmdline into
arm_load_kernel().
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Liu Jingqi <jingqi.liu@intel.com>
Suggested-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Tao Xu <tao3.xu@intel.com>
Message-Id: <20190809065731.9097-2-tao3.xu@intel.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Cédric Le Goater <clg@kaod.org>
[ehabkost: include hw/boards.h again to fix build failures]
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
No header includes qemu-common.h after this commit, as prescribed by
qemu-common.h's file comment.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190523143508.25387-5-armbru@redhat.com>
[Rebased with conflicts resolved automatically, except for
include/hw/arm/xlnx-zynqmp.h hw/arm/nrf51_soc.c hw/arm/msf2-soc.c
block/qcow2-refcount.c block/qcow2-cluster.c block/qcow2-cache.c
target/arm/cpu.h target/lm32/cpu.h target/m68k/cpu.h target/mips/cpu.h
target/moxie/cpu.h target/nios2/cpu.h target/openrisc/cpu.h
target/riscv/cpu.h target/tilegx/cpu.h target/tricore/cpu.h
target/unicore32/cpu.h target/xtensa/cpu.h; bsd-user/main.c and
net/tap-bsd.c fixed up]
The header file hw/arm/arm.h now includes only declarations
relating to hw/arm/boot.c functionality. Rename it accordingly,
and adjust its header comment.
The bulk of this commit was created via
perl -pi -e 's|hw/arm/arm.h|hw/arm/boot.h|' hw/arm/*.c include/hw/arm/*.h
In a few cases we can just delete the #include:
hw/arm/msf2-soc.c, include/hw/arm/aspeed_soc.h and
include/hw/arm/bcm2836.h did not require it.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190516163857.6430-4-peter.maydell@linaro.org
Our pflash devices are simplistically modelled has having
"num-blocks" sectors of equal size "sector-length". Real hardware
commonly has sectors of different sizes. How our "sector-length"
property is related to the physical device's multiple sector sizes
is unclear.
Helper functions pflash_cfi01_register() and pflash_cfi02_register()
create a pflash device, set properties including "sector-length" and
"num-blocks", and realize. They take parameters @size, @sector_len
and @nb_blocs.
QOMification left parameter @size unused. Obviously, @size should
match @sector_len and @nb_blocs, i.e. size == sector_len * nb_blocs.
All callers satisfy this.
Remove @nb_blocs and compute it from @size and @sector_len.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20190308094610.21210-16-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
QOMification left parameter @qdev unused in pflash_cfi01_register()
and pflash_cfi02_register(). All callers pass NULL. Remove.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190308094610.21210-15-armbru@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Remove those unneeded includes to speed up the compilation
process a little bit. (Continue 7eceff5b5a cleanup)
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20180528232719.4721-13-f4bug@amsat.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Change all the uses of serial_hds[] to go via the new
serial_hd() function. Code change produced with:
find hw -name '*.[ch]' | xargs sed -i -e 's/serial_hds\[\([^]]*\)\]/serial_hd(\1)/g'
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-id: 20180420145249.32435-8-peter.maydell@linaro.org
there are 2 use cases to deal with:
1: fixed CPU models per board/soc
2: boards with user configurable cpu_model and fallback to
default cpu_model if user hasn't specified one explicitly
For the 1st
drop intermediate cpu_model parsing and use const cpu type
directly, which replaces:
typename = object_class_get_name(
cpu_class_by_name(TYPE_ARM_CPU, cpu_model))
object_new(typename)
with
object_new(FOO_CPU_TYPE_NAME)
or
cpu_generic_init(BASE_CPU_TYPE, "my cpu model")
with
cpu_create(FOO_CPU_TYPE_NAME)
as result 1st use case doesn't have to invoke not necessary
translation and not needed code is removed.
For the 2nd
1: set default cpu type with MachineClass::default_cpu_type and
2: use generic cpu_model parsing that done before machine_init()
is run and:
2.1: drop custom cpu_model parsing where pattern is:
typename = object_class_get_name(
cpu_class_by_name(TYPE_ARM_CPU, cpu_model))
[parse_features(typename, cpu_model, &err) ]
2.2: or replace cpu_generic_init() which does what
2.1 does + create_cpu(typename) with just
create_cpu(machine->cpu_type)
as result cpu_name -> cpu_type translation is done using
generic machine code one including parsing optional features
if supported/present (removes a bunch of duplicated cpu_model
parsing code) and default cpu type is defined in an uniform way
within machine_class_init callbacks instead of adhoc places
in boadr's machine_init code.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <1505318697-77161-6-git-send-email-imammedo@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Set the MachineClass flag ignore_memory_transaction_failures
for almost all ARM boards. This means they retain the legacy
behaviour that accesses to unimplemented addresses will RAZ/WI
rather than aborting, when a subsequent commit adds support
for external aborts.
The exceptions are:
* virt -- we know that guests won't try to prod devices
that we don't describe in the device tree or ACPI tables
* mps2 -- this board was written to use unimplemented-device
for all the ranges with devices we don't yet handle
New boards should not set the flag, but instead be written
like the mps2.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 1504626814-23124-3-git-send-email-peter.maydell@linaro.org
For the Xilinx boards:
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Use the new functions memory_region_init_{ram,rom,rom_device}()
instead of manually calling the _nomigrate() version and then
vmstate_register_ram_global().
Patch automatically created using coccinelle script:
spatch --in-place -sp_file scripts/coccinelle/memory-region-init-ram.cocci -dir hw
(As it turns out, there are no instances of the rom and
rom_device functions that are caught by this script.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-id: 1499438577-7674-8-git-send-email-peter.maydell@linaro.org
Rename memory_region_init_ram() to memory_region_init_ram_nomigrate().
This leaves the way clear for us to provide a memory_region_init_ram()
which does handle migration.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-id: 1499438577-7674-4-git-send-email-peter.maydell@linaro.org
Block backends defined with -drive if=scsi are meant to be picked up
by machine initialization code: a suitable frontend gets created and
wired up automatically.
if=scsi drives not picked up that way can still be used with -device
as if they had if=none, but that's unclean and best avoided. Unused
ones produce an "Orphaned drive without device" warning.
A few machine types default to if=scsi, even though they don't
actually have a SCSI HBA. This makes no sense. Change their default
to if=none. Affected machines:
* aarch64/arm: realview-pbx-a9 vexpress-a9 vexpress-a15 xilinx-zynq-a9
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: "Edgar E. Iglesias" <edgar.iglesias@gmail.com>
Cc: Alistair Francis <alistair.francis@xilinx.com>
Cc: qemu-arm@nongnu.org
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-Id: <1487153147-11530-5-git-send-email-armbru@redhat.com>
This allows specifying the property via -drive if=none and creating
the flash device with -device.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 1467138270-32481-6-git-send-email-clg@kaod.org
[clg: added an extra fix for sabrelite_init()
keeping the test on flash_dev did not seem necessary. ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* drop qemu_char_get_next_serial and use chardev prop
* create cadence_uart_create wrapper function to create
cadence_uart_device
* change affected board code to use the new way
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Message-id: 1465028065-5855-3-git-send-email-zxq_yx_007@163.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Commit 57cb38b included qapi/error.h into qemu/osdep.h to get the
Error typedef. Since then, we've moved to include qemu/osdep.h
everywhere. Its file comment explains: "To avoid getting into
possible circular include dependencies, this file should not include
any other QEMU headers, with the exceptions of config-host.h,
compiler.h, os-posix.h and os-win32.h, all of which are doing a
similar job to this file and are under similar constraints."
qapi/error.h doesn't do a similar job, and it doesn't adhere to
similar constraints: it includes qapi-types.h. That's in excess of
100KiB of crap most .c files don't actually need.
Add the typedef to qemu/typedefs.h, and include that instead of
qapi/error.h. Include qapi/error.h in .c files that need it and don't
get it now. Include qapi-types.h in qom/object.h for uint16List.
Update scripts/clean-includes accordingly. Update it further to match
reality: replace config.h by config-target.h, add sysemu/os-posix.h,
sysemu/os-win32.h. Update the list of includes in the qemu/osdep.h
comment quoted above similarly.
This reduces the number of objects depending on qapi/error.h from "all
of them" to less than a third. Unfortunately, the number depending on
qapi-types.h shrinks only a little. More work is needed for that one.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
[Fix compilation without the spice devel packages. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Move the creation of the SD card device from the sdhci_sysbus
device itself into the boards that create these devices.
This allows us to remove the cannot_instantiate_with_device_add
notation because we no longer call drive_get_next in the device
model.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 1455646193-13238-7-git-send-email-peter.maydell@linaro.org
Move the ssi.h include file into the ssi directory.
While touching the code also fix the typdef lines as
checkpatch complains.
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Signed-off-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1449505425-32022-4-git-send-email-peter.maydell@linaro.org
Done with this Coccinelle semantic patch:
@@
type T;
identifier FUN, RET;
expression list ARGS;
expression ERR, EC;
@@
(
- T RET = FUN(ARGS, &ERR);
+ T RET = FUN(ARGS, &error_fatal);
|
- RET = FUN(ARGS, &ERR);
+ RET = FUN(ARGS, &error_fatal);
|
- FUN(ARGS, &ERR);
+ FUN(ARGS, &error_fatal);
)
- if (ERR != NULL) {
- error_report_err(ERR);
- exit(EC);
- }
This is actually a more elegant version of my initial semantic patch
by courtesy of Eduardo.
It leaves dead Error * variables behind, cleaned up manually.
Cc: qemu-arm@nongnu.org
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Add support for the Xilinx XADC core used in Zynq 7000.
References:
- Zynq-7000 All Programmable SoC Technical Reference Manual
- 7 Series FPGAs and Zynq-7000 All Programmable SoC XADC
Dual 12-Bit 1 MSPS Analog-to-Digital Converter
Tested with Linux using QEMU machine xilinx-zynq-a9 with devicetree
files zynq-zc702.dtb and zynq-zc706.dtb, and kernel configuration
multi_v7_defconfig.
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
[ PC changes:
* Changed macro names to match TRM where possible
* Made programmers model macro scheme consistent
* Dropped XADC_ZYNQ_ prefix on local macros
* Fix ALM field width
* Update threshold-comparison interrupts in _update_ints()
* factored out DFIFO pushes into helper. Renamed to "push/pop"
* Changed xadc_reg to 10 bits and added OOB check.
* Reduced scope of MCTL reset to just stop channel coms.
* Added dummy read data to write commands
* Changed _ to - seperators in string names and filenames
* Dropped ------------ in header comment
* Catchall'ed _update_ints() in _write handler.
* Minor whitespace changes.
* Use ZYNQ_XADC_FIFO_DEPTH instead of ARRAY_SIZE()
]
Signed-off-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
