At present we calculate the recommended hash page table (HPT) size for a
pseries guest just once in ppc_spapr_init() before allocating the HPT.
In future patches we're going to want this calculation in other places, so
this splits it out into a helper function. While we're at it, change the
calculation to use ctz() instead of an explicit loop.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
When migrating the 'pseries' machine type with KVM, we use a special fd
to access the hash page table stored within KVM. Usually, this fd is
opened at the beginning of migration, and kept open until the migration
is complete.
However, if there is a guest reset during the migration, the fd can become
stale and we need to re-open it. At the moment we use an 'htab_fd_stale'
flag in sPAPRMachineState to signal this, which is checked in the migration
iterators.
But that's rather ugly. It's simpler to just close and invalidate the
fd on reset, and lazily re-open it in migration if necessary. This patch
implements that change.
This requires a small addition to the machine state's instance_init,
so that htab_fd is initialized to -1 (telling the migration code it
needs to open it) instead of 0, which could be a valid fd.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
The functions for migrating the hash page table on pseries machine type
(htab_save_setup() and htab_load()) can report some errors with an
explicit fprintf() before returning an appropriate error code. Change some
of these to use error_report() instead. htab_save_setup() is omitted for
now to avoid conflicts with some other in-progress work.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
This function includes a number of explicit fprintf()s for errors.
Change these to use error_report() instead.
Also replace the single exit(EXIT_FAILURE) with an explicit exit(1), since
the latter is the more usual idiom in qemu by a large margin.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Use the error handling infrastructure to pass an error out from
try_create_xics() instead of assuming &error_abort - the caller is in a
better position to decide on error handling policy.
Also change the error handling from an &error_abort to &error_fatal, since
this occurs during the initial machine construction and could be triggered
by bad configuration rather than a program error.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Use error_setg() to return an error rather than an explicit exit().
Previously it was an exit(0) instead of a non-zero exit code, which was
simply a bug. Also improve the error message.
While we're at it change the type of spapr_vga_init() to bool since that's
how we're using it anyway.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Use error_setg() and return an error, rather than using an explicit exit().
Also improve messages, and be more explicit about which constraint failed.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Bharata B Rao <bharata@linux.vnet.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Currently spapr_cpu_init() is hardcoded to handle any errors as fatal.
That works for now, since it's only called from initial setup where an
error here means we really can't proceed.
However, we'll want to handle this more flexibly for cpu hotplug in future
so generalize this using the error reporting infrastructure. While we're
at it make a small cleanup in a related part of ppc_spapr_init() to use
error_report() instead of an old-style explicit fprintf().
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Bharata B Rao <bharata@linux.vnet.ibm.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Current ppc_set_compat() returns -1 for errors, and also (unconditionally)
reports an error message. The caller in h_client_architecture_support()
may then report it again using an outdated fprintf().
Clean this up by using the modern error reporting mechanisms. Also add
strerror(errno) to the error message.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
If guest doesn't have any dynamically reconfigurable (DR) logical memory
blocks (LMB), then we shouldn't create ibm,dynamic-reconfiguration-memory
device tree node.
Signed-off-by: Bharata B Rao <bharata@linux.vnet.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1453832250-766-6-git-send-email-peter.maydell@linaro.org
Commit 6daf194d, be62a2eb and 312fd5f got rid of a bunch, but they
keep coming back. Tracked down with the Coccinelle semantic patch
from commit 312fd5f.
Cc: Fam Zheng <famz@redhat.com>
Cc: Peter Crosthwaite <crosthwaitepeter@gmail.com>
Cc: Bharata B Rao <bharata@linux.vnet.ibm.com>
Cc: Dominik Dingel <dingel@linux.vnet.ibm.com>
Cc: David Hildenbrand <dahi@linux.vnet.ibm.com>
Cc: Jason J. Herne <jjherne@linux.vnet.ibm.com>
Cc: Stefan Berger <stefanb@linux.vnet.ibm.com>
Cc: Dr. David Alan Gilbert <dgilbert@redhat.com>
Cc: Changchun Ouyang <changchun.ouyang@intel.com>
Cc: zhanghailiang <zhang.zhanghailiang@huawei.com>
Cc: Pavel Fedin <p.fedin@samsung.com>
Signed-off-by: Markus Armbruster <armbru@pond.sub.org>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Acked-by: Bharata B Rao <bharata@linux.vnet.ibm.com>
Acked-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <1450452927-8346-17-git-send-email-armbru@redhat.com>
Not caught by Coccinelle, because we report the error only
conditionally here.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <1450452927-8346-14-git-send-email-armbru@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <1449764955-10741-3-git-send-email-armbru@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Cc: David Gibson <david@gibson.dropbear.id.au>
Cc: Alexander Graf <agraf@suse.de>
Cc: qemu-ppc@nongnu.org
Signed-off-by: Li Zhijian <lizhijian@cn.fujitsu.com>
[fixed return type of spapr_machine_finalizefn()]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The OHCI has some bugs and performance issues, so for
newer machines it's preferable to use XHCI instead.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This tweaks the way the default machine version is controlled, so that
there will be a bit less churn when each new version is introduced.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Currently each of the *_class_options() functions for the pseries-2.1 ..
pseries-2.5 machine types are standalone. This will become harder to
maintain as new versions are added.
This patch restructures them similarly to x86 where each function calls
the one from the next version, then overrides anything necessary for
compatibility with the specific version and older.
The default behaviour - that for the most recent machine are set up in
the base class initializer spapr_machine_class_init(). Previously it had
some things set up to default to older behaviour with the more recent
machines overriding it.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
At the moment all the class_init functions and TypeInfo structures for the
various versioned pseries machine types are open-coded. As more versions
are created this is getting increasingly clumsy.
This patch borrows the approach used in PC, using a DEFINE_SPAPR_MACHINE()
macro to construct most of the boilerplate from simpler 'class_options' and
'instance_options' functions.
This patch makes a small semantic change - the versioned machine types are
now registered through machine_init() instead of type_init(). Since the
new way is how PC already did it, I'm assuming that's correct.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Sam Bobroff <sam.bobroff@au1.ibm.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
To make the spapr_machine_*_class_init() functions a little less bulky.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Currently, the versioned spapr machine types put the machine type version
into the description string. PC does not do this, using just the name
itself to distinguish. Doing the same lets us move setting the description
into the common base class, simplifying the code slightly.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
The instance_init() functions for several of the pseries-x.y versioned
machine types explicitly call spapr_machine_initfn(). But that's the
instance_init function for the common parent of all those machine types,
so will already have been called beforehand by the QOM infrastructure.
Remove the redundant calls.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
hw/ppc/spapr.c has a number of definitions related to the various versioned
machine types ("pseries-2.1" .. "pseries-2.5") it defines. These are
mostly arranged by type of function first, then machine version second, and
it's not consistent about whether it goes in increasing or decreasing
version order.
This rearranges the code to keep all the definitions for a particular
machine version together, and arrange then consistently in order most
recent to least recent.
This brings us closer to matching the way PC does things, and makes later
cleanups easier to follow.
Apart from adding some comments marking each section, this is a pure
mechanical rearrangement with no semantic changes.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
98cec76 "machine: Set MachineClass::name automatically" removed the setting
of mc->name for the pseries machine types, since it can be derived
automatically from the type names constructed with MACHINE_TYPE_NAME().
Unfortunately fb0fc8f "spapr: Create pseries-2.5 machine" went in later and
brought one of them back.
This removes it again.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Section B.6.2.1 Root Node Properties of PAPR specification defines
a set of properties which shall be present in the device tree root,
one of these properties is "system-id" which "should be unique across
all systems and all manufacturers". Since UUID is meant to be unique,
it makes sense to use it as "system-id".
This adds "system-id" property to the device tree root when not empty.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The "pseries" alias is currently set twice, one time for the
pseries-2.4 machine and one time for the "pseries-2.5" machine.
To avoid confusion with the alias, let's remove the one from
the older machine class. And while we're at it, also remove
the "is_default = 0" there since the is_default variable
should be set to zero by default already.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
hw/ppc/spapr.c: Fix memory leak on error, it was introduced in bc09e0611
hw/acpi/memory_hotplug.c: Fix memory leak on error, it was introduced in 34f2af3d
Signed-off-by: Stefano Dong (董兴水) <opensource.dxs@aliyun.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
KVM_PPC_ALLOCATE_HTAB ioctl can return -ENOMEM for KVM guests and QEMU
never handled this correctly. But this didn't cause any problems till
now as KVM_PPC_ALLOCATE_HTAB ioctl returned with smaller than requested
HTAB when enough contiguous memory wasn't available in the host.
After the proposed kernel change: https://patchwork.ozlabs.org/patch/530501/,
KVM_PPC_ALLOCATE_HTAB ioctl will not fallback to lower sized HTAB
allocation and will fail if requested HTAB size can't be met.
Check for such failures in QEMU and abort appropriately. This will
prevent guest kernel from hanging/freezing during early boot by doing
graceful exit when host is unable to allocate requested HTAB.
Signed-off-by: Bharata B Rao <bharata@linux.vnet.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
In postcopy we're going to need to perform the complete phase
for postcopiable devices at a different point, start out by
renaming all of the 'complete's to make the difference obvious.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
HW_COMPAT_2_4 will become non-empty: prepare for it.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Message-id: 1444991154-79217-3-git-send-email-cornelia.huck@de.ibm.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
LoPAPR defines a "ibm,pa-features" per-CPU device tree property which
describes extended features of the Processor Architecture.
This adds the property to the device tree. At the moment this is the
copy of what pHyp advertises except "I=1 (cache inhibited) Large Pages"
which is enabled for TCG and disabled when running under HV KVM host
with 4K system page size.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
[aik: rebased, changed commit log, moved ci_large_pages initialization,
renamed pa_features arrays]
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
According to a commit message in the Linux kernel (see here
https://git.kernel.org/cgit/linux/kernel/git/torvalds/linux.git/commit/?id=b60c31d85a2a
for example), the name of the property that carries the information
about the number of SLB entries should be called "slb-size", and
not "ibm,slb-size". The Linux kernel can deal with both names, but
to be on the safe side we should support the official name, too.
[Now that LoPAPR is public, the relevant requirement can be found in
section C.6.1.8 --dwg]
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Terminate the guest when HTAB of requested size isn't allocated by
the host.
When memory hotplug is attempted on a guest that has booted with
less than requested HTAB size, the guest kernel will not be able
to gracefully fail the hotplug request. This patch will ensure that
we never end up in a situation where memory hotplug fails due to
less than requested HTAB size.
Signed-off-by: Bharata B Rao <bharata@linux.vnet.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Allocate HTAB from ppc_spapr_init() so that we can abort the guest
if requested HTAB size is't allocated by the host. However retain the
htab reset call in spapr_reset_htab() so that HTAB gets reset (and
not allocated) during machine reset.
Signed-off-by: Bharata B Rao <bharata@linux.vnet.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
It works fine with the Linux driver out of the box
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
setting gap to TRUE will make sparse DIMM
address auto allocation, leaving gaps between
a new DIMM address and preceeding existing DIMM.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Rename ELF_MACHINE to be PPC specific. This is used as-is by the
various PPC bootloaders and is locally defined to ELF_MACHINE in linux
user in PPC specific ifdeffery.
This removes another architecture specific definition from the global
namespace (as desired by multi-arch).
Cc: Alexander Graf <agraf@suse.de>
Cc: qemu-ppc@nongnu.org
Reviewed-by: Richard Henderson <rth@twiddle.net>
Acked-By: Riku Voipio <riku.voipio@linaro.org>
Signed-off-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The PAPR interface defines a hypercall to pass high-quality
hardware generated random numbers to guests. Recent kernels can
already provide this hypercall to the guest if the right hardware
random number generator is available. But in case the user wants
to use another source like EGD, or QEMU is running with an older
kernel, we should also have this call in QEMU, so that guests that
do not support virtio-rng yet can get good random numbers, too.
This patch now adds a new pseudo-device to QEMU that either
directly provides this hypercall to the guest or is able to
enable the in-kernel hypercall if available. The in-kernel
hypercall can be enabled with the use-kvm property, e.g.:
qemu-system-ppc64 -device spapr-rng,use-kvm=true
For handling the hypercall in QEMU instead, a "RngBackend" is
required since the hypercall should provide "good" random data
instead of pseudo-random (like from a "simple" library function
like rand() or g_random_int()). Since there are multiple RngBackends
available, the user must select an appropriate back-end via the
"rng" property of the device, e.g.:
qemu-system-ppc64 -object rng-random,filename=/dev/hwrng,id=gid0 \
-device spapr-rng,rng=gid0 ...
See http://wiki.qemu-project.org/Features-Done/VirtIORNG for
other example of specifying RngBackends.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The buffer that is allocated in spapr_populate_drconf_memory()
is used for setting both, the "ibm,dynamic-memory" and the
"ibm,associativity-lookup-arrays" property. However, only the
size of the first one is taken into account when allocating the
memory. So if the length of the second property is larger than
the length of the first one, we run into a buffer overflow here!
Fix it by taking the length of the second property into account,
too.
Fixes: "spapr: Support ibm,dynamic-reconfiguration-memory" patch
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
At present, if guest numa nodes are requested, but the cpus in each node
are not specified, spapr just uses the default behaviour or assigning each
vcpu round-robin to nodes.
If smp_threads != 1, that will assign adjacent threads in a core to
different NUMA nodes. As well as being just weird, that's a configuration
that can't be represented in the device tree we give to the guest, which
means the guest and qemu end up with different ideas of the NUMA topology.
This patch implements mc->cpu_index_to_socket_id in the spapr code to
make sure vcpus get assigned to nodes only at the socket granularity.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Till now memory hotplug used RTAS_LOG_V6_HP_ID_DRC_INDEX hotplug type
which meant that we generated one hotplug type of EPOW event for every
256MB (SPAPR_MEMORY_BLOCK_SIZE). This quickly overruns the kernel
rtas log buffer thus resulting in loss of memory hotplug events. Switch
to RTAS_LOG_V6_HP_ID_DRC_COUNT hotplug type for memory so that we
generate only one event per hotplug request.
Signed-off-by: Bharata B Rao <bharata@linux.vnet.ibm.com>
Reviewed-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Support hotplug identifier type RTAS_LOG_V6_HP_ID_DRC_COUNT that allows
hotplugging of DRCs by specifying the DRC count.
While we are here, rename
spapr_hotplug_req_add_event() to spapr_hotplug_req_add_by_index()
spapr_hotplug_req_remove_event() to spapr_hotplug_req_remove_by_index()
so that they match with spapr_hotplug_req_add_by_count().
Signed-off-by: Bharata B Rao <bharata@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Don't represent non-hotluggable memory under drconf node. With this
we don't have to create DRC objects for them.
The effect of this patch is that we revert back to memory@XXXX representation
for all the memory specified with -m option and represent the cold
plugged memory and hot-pluggable memory under
ibm,dynamic-reconfiguration-memory.
Signed-off-by: Bharata B Rao <bharata@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
When NUMA isn't configured explicitly, assume node 0 is present for
the purpose of creating ibm,associativity-lookup-arrays property
under ibm,dynamic-reconfiguration-memory DT node. This ensures that
the associativity index property is correctly updated in ibm,dynamic-memory
for the LMB that is hotplugged.
Signed-off-by: Bharata B Rao <bharata@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Currently when user specifies more slots than allowed max of
SPAPR_MAX_RAM_SLOTS (32), we error out like this:
qemu-system-ppc64: unsupported amount of memory slots: 64
Let the user know about the max allowed slots like this:
qemu-system-ppc64: Specified number of memory slots 64 exceeds max supported 32
Signed-off-by: Bharata B Rao <bharata@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Currently PowerPC kernel doesn't allow hot-adding memory to memory-less
node, but instead will silently add the memory to the first node that has
some memory. This causes two unexpected behaviours for the user.
- Memory gets hotplugged to a different node than what the user specified.
- Since pc-dimm subsystem in QEMU still thinks that memory belongs to
memory-less node, a reboot will set things accordingly and the previously
hotplugged memory now ends in the right node. This appears as if some
memory moved from one node to another.
So until kernel starts supporting memory hotplug to memory-less
nodes, just prevent such attempts upfront in QEMU.
Signed-off-by: Bharata B Rao <bharata@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Make use of pc-dimm infrastructure to support memory hotplug
for PowerPC.
Signed-off-by: Bharata B Rao <bharata@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The hash table size is dependent on ram_size, but since with hotplug
the memory can grow till maxram_size. Hence make hash table size dependent
on maxram_size.
This allows to hotplug huge amounts of memory to the guest.
Signed-off-by: Bharata B Rao <bharata@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
David Gibson
Bharata B Rao
Peter Maydell
Markus Armbruster
Thomas Huth
Alexey Kardashevskiy
Stefano Dong (董兴水)
Dr. David Alan Gilbert
Cornelia Huck
Michael S. Tsirkin
Benjamin Herrenschmidt
Igor Mammedov
Peter Crosthwaite