Return default value in legacy mode for BAR4 when unset. This can't be
set in reset method because BARs are cleared on reset so we return it
instead when BARs are read in legacy mode. This fixes UDMA on amigaone
with AmigaOS.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-ID: <20231125140135.AF6A075A4C3@zero.eik.bme.hu>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Allow the VIA IDE controller to switch between both legacy and native modes by
calling pci_ide_update_mode() to reconfigure the device whenever PCI_CLASS_PROG
is updated.
This patch moves the initial setting of PCI_CLASS_PROG from via_ide_realize() to
via_ide_reset(), and removes the direct setting of PCI_INTERRUPT_PIN during PCI
bus reset since this is now managed by pci_ide_update_mode(). This ensures that
the device configuration is always consistent with respect to the currently
selected mode.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-ID: <20231116103355.588580-5-mark.cave-ayland@ilande.co.uk>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The via-ide device currently attempts to set the default BAR addresses to the
values shown in the datasheet, but this doesn't work for 2 reasons: firstly
BARS 1-4 do not set the bottom 2 bits to PCI_BASE_ADDRESS_SPACE_IO, and
secondly the initial PCI bus reset clears the values of all PCI device BARs
after the device itself has been reset.
Remove the setting of the default BAR addresses from via_ide_reset() to ensure
there is no doubt that these values are never exposed to the guest.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-ID: <20231116103355.588580-4-mark.cave-ayland@ilande.co.uk>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This function reads the value of the PCI_CLASS_PROG register for PCI IDE
controllers and configures the PCI BARs and/or IDE ioports accordingly.
In the case where we switch to legacy mode, the PCI BARs are set to return zero
(as suggested in the "PCI IDE Controller" specification), the legacy IDE ioports
are enabled, and the PCI interrupt pin cleared to indicate legacy IRQ routing.
Conversely when we switch to native mode, the legacy IDE ioports are disabled
and the PCI interrupt pin set to indicate native IRQ routing. The contents of
the PCI BARs are unspecified, but this is not an issue since if a PCI IDE
controller has been switched to native mode then its BARs will need to be
programmed.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-ID: <20231116103355.588580-3-mark.cave-ayland@ilande.co.uk>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
These definitions are present in ioport.c which is currently only available when
CONFIG_IDE_ISA is enabled. Move them to the IDE core so that they can be made
available to PCI IDE controllers that support switching to legacy mode.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-ID: <20231116103355.588580-2-mark.cave-ayland@ilande.co.uk>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Legacy software contains a standard mechanism for generating a reset to a
Serial ATA device - setting the SRST (software reset) bit in the Device
Control register.
Serial ATA has a more robust mechanism called COMRESET, also referred to
as port reset. A port reset is the preferred mechanism for error
recovery and should be used in place of software reset.
Commit e2a5d9b3d9 ("hw/ide/ahci: simplify and document PxCI handling")
improved the handling of PxCI, such that PxCI gets cleared after handling
a non-NCQ, or NCQ command (instead of incorrectly clearing PxCI after
receiving anything - even a FIS that failed to parse, which should NOT
clear PxCI, so that you can see which command slot that caused an error).
However, simply clearing PxCI after a non-NCQ, or NCQ command, is not
enough, we also need to clear PxCI when receiving a SRST in the Device
Control register.
A legacy software reset is performed by the host sending two H2D FISes,
the first H2D FIS asserts SRST, and the second H2D FIS deasserts SRST.
The first H2D FIS will not get a D2H reply, and requires the FIS to have
the C bit set to one, such that the HBA itself will clear the bit in PxCI.
The second H2D FIS will get a D2H reply once the diagnostic is completed.
The clearing of the bit in PxCI for this command should ideally be done
in ahci_init_d2h() (if it was a legacy software reset that caused the
reset (a COMRESET does not use a command slot)). However, since the reset
value for PxCI is 0, modify ahci_reset_port() to actually clear PxCI to 0,
that way we can avoid complex logic in ahci_init_d2h().
This fixes an issue for FreeBSD where the device would fail to reset.
The problem was not noticed in Linux, because Linux uses a COMRESET
instead of a legacy software reset by default.
Fixes: e2a5d9b3d9 ("hw/ide/ahci: simplify and document PxCI handling")
Reported-by: Marcin Juszkiewicz <marcin.juszkiewicz@linaro.org>
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Message-ID: <20231108222657.117984-1-nks@flawful.org>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Tested-by: Marcin Juszkiewicz <marcin.juszkiewicz@linaro.org>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
- Graph locking part 6 (bs->file/backing)
- ahci: trigger either error IRQ or regular IRQ, not both
-----BEGIN PGP SIGNATURE-----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=ikBW
-----END PGP SIGNATURE-----
Merge tag 'for-upstream' of https://repo.or.cz/qemu/kevin into staging
Block layer patches
- Graph locking part 6 (bs->file/backing)
- ahci: trigger either error IRQ or regular IRQ, not both
# -----BEGIN PGP SIGNATURE-----
#
# iQJFBAABCAAvFiEE3D3rFZqa+V09dFb+fwmycsiPL9YFAmVLvccRHGt3b2xmQHJl
# ZGhhdC5jb20ACgkQfwmycsiPL9ZkFg//awQoPiGnYzHpqcx2tGCM2AqBV+mFkbZr
# BKI5vp8FYfJtgMuHjC8jabL24NRMPpT+HbCzoxwjJU+nnnr85qr7R5iGwG6kfgX6
# HJlAXYXdY6e7l+FV44PBJ52vOoGCsh1GHg8HlKsHMaxSdXi9C1axHJ6rCAjnWXE0
# FQ4znCBVs/9HiKsvu4Wdm5muX2ShftFRM/toAwA+fLEOealX8WEXoRFJXI40bYbR
# OR7aJXWMDQrljlqdKk2FXvK337/tpofXmXf3NIE1R2pmY4x5Fg8bfChZn4UaaCdN
# n+0AhmE4ScI0rXuaXXYOvTO9vdTzXeBROG6tX03t9rrQfB6wPcGVeXRo/uusslAW
# sDH8NLz7uHFOooV02Fs8CKDdVrNNw5qjziclSGa0Po7vqOV1TKI8OTiNpsDLmdI5
# +DQvC6N+IU1pSOXImATSHkheGWggsegrsgN6PdrlzHEXJwWoAaRD0T06MRn74/pL
# gCegK2ez4RJYsci7C5b0gaqY/QBsMj8EUfEGVHvVyuVSoPRwiq4ehPqSQ+siA3xP
# KxYR0e4+QIfRmxqCzaJhiQ3DDGdt8UcO3yF0XcKXEqWwgFAGQKNeUG314jginvmA
# iaJzC0dHbiGcagAk7Ey8iyzfxQDWM6ixzJtGv7VLILepzCuu8vaJXy5qeEtTM/ZI
# EXoDGceNSvw=
# =ikBW
# -----END PGP SIGNATURE-----
# gpg: Signature made Thu 09 Nov 2023 00:56:39 HKT
# gpg: using RSA key DC3DEB159A9AF95D3D7456FE7F09B272C88F2FD6
# gpg: issuer "kwolf@redhat.com"
# gpg: Good signature from "Kevin Wolf <kwolf@redhat.com>" [full]
# Primary key fingerprint: DC3D EB15 9A9A F95D 3D74 56FE 7F09 B272 C88F 2FD6
* tag 'for-upstream' of https://repo.or.cz/qemu/kevin: (25 commits)
hw/ide/ahci: trigger either error IRQ or regular IRQ, not both
block: Protect bs->file with graph_lock
block: Take graph lock for most of .bdrv_open
vhdx: Take locks for accessing bs->file
qcow2: Take locks for accessing bs->file
block: Add missing GRAPH_RDLOCK annotations
block: Introduce bdrv_co_change_backing_file()
blkverify: Add locking for request_fn
block: Protect bs->backing with graph_lock
block: Mark bdrv_replace_node() GRAPH_WRLOCK
block: Mark bdrv_replace_node_common() GRAPH_WRLOCK
block: Inline bdrv_set_backing_noperm()
block: Mark bdrv_set_backing_hd_drained() GRAPH_WRLOCK
block: Mark bdrv_cow_child() and callers GRAPH_RDLOCK
block: Mark bdrv_filter_child() and callers GRAPH_RDLOCK
block: Mark bdrv_chain_contains() and callers GRAPH_RDLOCK
block: Mark bdrv_(un)freeze_backing_chain() and callers GRAPH_RDLOCK
block: Mark bdrv_skip_filters() and callers GRAPH_RDLOCK
block: Mark bdrv_skip_implicit_filters() and callers GRAPH_RDLOCK
block: Mark bdrv_filter_or_cow_bs() and callers GRAPH_RDLOCK
...
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
According to AHCI 1.3.1, 5.3.8.1 RegFIS:Entry, if ERR_STAT is set,
we jump to state ERR:FatalTaskfile, which will raise a TFES IRQ
unconditionally, regardless if the I bit is set in the FIS or not.
Thus, we should never raise a normal IRQ after having sent an error
IRQ.
NOTE: for QEMU platforms that use SeaBIOS, this patch depends on QEMU
commit 784155cdcb ("seabios: update submodule to git snapshot"), and
QEMU commit 14f5a7bae4 ("seabios: update binaries to git snapshot"),
which update SeaBIOS to a version that contains SeaBIOS commit 1281e340
("ahci: handle TFES irq correctly").
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Message-ID: <20231011131220.1992064-1-nks@flawful.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
If there is a pending DMA operation during ide_bus_reset(), the fact
that the IDEState is already reset before the operation is canceled
can be problematic. In particular, ide_dma_cb() might be called and
then use the reset IDEState which contains the signature after the
reset. When used to construct the IO operation this leads to
ide_get_sector() returning 0 and nsector being 1. This is particularly
bad, because a write command will thus destroy the first sector which
often contains a partition table or similar.
Traces showing the unsolicited write happening with IDEState
0x5595af6949d0 being used after reset:
> ahci_port_write ahci(0x5595af6923f0)[0]: port write [reg:PxSCTL] @ 0x2c: 0x00000300
> ahci_reset_port ahci(0x5595af6923f0)[0]: reset port
> ide_reset IDEstate 0x5595af6949d0
> ide_reset IDEstate 0x5595af694da8
> ide_bus_reset_aio aio_cancel
> dma_aio_cancel dbs=0x7f64600089a0
> dma_blk_cb dbs=0x7f64600089a0 ret=0
> dma_complete dbs=0x7f64600089a0 ret=0 cb=0x5595acd40b30
> ahci_populate_sglist ahci(0x5595af6923f0)[0]
> ahci_dma_prepare_buf ahci(0x5595af6923f0)[0]: prepare buf limit=512 prepared=512
> ide_dma_cb IDEState 0x5595af6949d0; sector_num=0 n=1 cmd=DMA WRITE
> dma_blk_io dbs=0x7f6420802010 bs=0x5595ae2c6c30 offset=0 to_dev=1
> dma_blk_cb dbs=0x7f6420802010 ret=0
> (gdb) p *qiov
> $11 = {iov = 0x7f647c76d840, niov = 1, {{nalloc = 1, local_iov = {iov_base = 0x0,
> iov_len = 512}}, {__pad = "\001\000\000\000\000\000\000\000\000\000\000",
> size = 512}}}
> (gdb) bt
> #0 blk_aio_pwritev (blk=0x5595ae2c6c30, offset=0, qiov=0x7f6420802070, flags=0,
> cb=0x5595ace6f0b0 <dma_blk_cb>, opaque=0x7f6420802010)
> at ../block/block-backend.c:1682
> #1 0x00005595ace6f185 in dma_blk_cb (opaque=0x7f6420802010, ret=<optimized out>)
> at ../softmmu/dma-helpers.c:179
> #2 0x00005595ace6f778 in dma_blk_io (ctx=0x5595ae0609f0,
> sg=sg@entry=0x5595af694d00, offset=offset@entry=0, align=align@entry=512,
> io_func=io_func@entry=0x5595ace6ee30 <dma_blk_write_io_func>,
> io_func_opaque=io_func_opaque@entry=0x5595ae2c6c30,
> cb=0x5595acd40b30 <ide_dma_cb>, opaque=0x5595af6949d0,
> dir=DMA_DIRECTION_TO_DEVICE) at ../softmmu/dma-helpers.c:244
> #3 0x00005595ace6f90a in dma_blk_write (blk=0x5595ae2c6c30,
> sg=sg@entry=0x5595af694d00, offset=offset@entry=0, align=align@entry=512,
> cb=cb@entry=0x5595acd40b30 <ide_dma_cb>, opaque=opaque@entry=0x5595af6949d0)
> at ../softmmu/dma-helpers.c:280
> #4 0x00005595acd40e18 in ide_dma_cb (opaque=0x5595af6949d0, ret=<optimized out>)
> at ../hw/ide/core.c:953
> #5 0x00005595ace6f319 in dma_complete (ret=0, dbs=0x7f64600089a0)
> at ../softmmu/dma-helpers.c:107
> #6 dma_blk_cb (opaque=0x7f64600089a0, ret=0) at ../softmmu/dma-helpers.c:127
> #7 0x00005595ad12227d in blk_aio_complete (acb=0x7f6460005b10)
> at ../block/block-backend.c:1527
> #8 blk_aio_complete (acb=0x7f6460005b10) at ../block/block-backend.c:1524
> #9 blk_aio_write_entry (opaque=0x7f6460005b10) at ../block/block-backend.c:1594
> #10 0x00005595ad258cfb in coroutine_trampoline (i0=<optimized out>,
> i1=<optimized out>) at ../util/coroutine-ucontext.c:177
Signed-off-by: Fiona Ebner <f.ebner@proxmox.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Tested-by: simon.rowe@nutanix.com
Message-ID: <20230906130922.142845-1-f.ebner@proxmox.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
When encountering an NCQ error, you should not write the NCQ tag to the
SError register. This is completely wrong.
The SError register has a clear definition, where each bit represents a
different error, see PxSERR definition in AHCI 1.3.1.
If we write a random value (like the NCQ tag) in SError, e.g. Linux will
read SError, and will trigger arbitrary error handling depending on the
NCQ tag that happened to be executing.
In case of success, ncq_cb() will call ncq_finish().
In case of error, ncq_cb() will call ncq_err() (which will clear
ncq_tfs->used), and then call ncq_finish(), thus using ncq_tfs->used is
sufficient to tell if finished should get set or not.
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20230609140844.202795-9-nks@flawful.org
Signed-off-by: John Snow <jsnow@redhat.com>
When there is an error, we need to raise a TFES error irq, see AHCI 1.3.1,
5.3.13.1 SDB:Entry.
If ERR_STAT is set, we jump to state ERR:FatalTaskfile, which will raise
a TFES IRQ unconditionally, regardless if the I bit is set in the FIS or
not.
Thus, we should never raise a normal IRQ after having sent an error IRQ.
It is valid to signal successfully completed commands as finished in the
same SDB FIS that generates the error IRQ. The important thing is that
commands that did not complete successfully (e.g. commands that were
aborted, do not get the finished bit set).
Before this commit, there was never a TFES IRQ raised on NCQ error.
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20230609140844.202795-8-nks@flawful.org
Signed-off-by: John Snow <jsnow@redhat.com>
For NCQ, PxCI is cleared on command queued successfully.
For non-NCQ, PxCI is cleared on command completed successfully.
Successfully means ERR_STAT, BUSY and DRQ are all cleared.
A command that has ERR_STAT set, does not get to clear PxCI.
See AHCI 1.3.1, section 5.3.8, states RegFIS:Entry and RegFIS:ClearCI,
and 5.3.16.5 ERR:FatalTaskfile.
In the case of non-NCQ commands, not clearing PxCI is needed in order
for host software to be able to see which command slot that failed.
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Message-id: 20230609140844.202795-7-nks@flawful.org
Signed-off-by: John Snow <jsnow@redhat.com>
According to AHCI 1.3.1 definition of PxSACT:
This field is cleared when PxCMD.ST is written from a '1' to a '0' by
software. This field is not cleared by a COMRESET or a software reset.
According to AHCI 1.3.1 definition of PxCI:
This field is also cleared when PxCMD.ST is written from a '1' to a '0'
by software.
Clearing PxCMD.ST is part of the error recovery procedure, see
AHCI 1.3.1, section "6.2 Error Recovery".
If we don't clear PxCI on error recovery, the previous command will
incorrectly still be marked as pending after error recovery.
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20230609140844.202795-6-nks@flawful.org
Signed-off-by: John Snow <jsnow@redhat.com>
The AHCI spec states that:
For NCQ, PxCI is cleared on command queued successfully.
For non-NCQ, PxCI is cleared on command completed successfully.
(A non-NCQ command that completes with error does not clear PxCI.)
The current QEMU implementation either clears PxCI in check_cmd(),
or in ahci_cmd_done().
check_cmd() will clear PxCI for a command if handle_cmd() returns 0.
handle_cmd() will return -1 if BUSY or DRQ is set.
The QEMU implementation for NCQ commands will currently not set BUSY
or DRQ, so they will always have PxCI cleared by handle_cmd().
ahci_cmd_done() will never even get called for NCQ commands.
Non-NCQ commands are executed by ide_bus_exec_cmd().
Non-NCQ commands in QEMU are implemented either in a sync or in an async
way.
For non-NCQ commands implemented in a sync way, the command handler will
return true, and when ide_bus_exec_cmd() sees that a command handler
returns true, it will call ide_cmd_done() (which will call
ahci_cmd_done()). For a command implemented in a sync way,
ahci_cmd_done() will do nothing (since busy_slot is not set). Instead,
after ide_bus_exec_cmd() has finished, check_cmd() will clear PxCI for
these commands.
For non-NCQ commands implemented in an async way (using either aiocb or
pio_aiocb), the command handler will return false, ide_bus_exec_cmd()
will not call ide_cmd_done(), instead it is expected that the async
callback function will call ide_cmd_done() once the async command is
done. handle_cmd() will set busy_slot, if and only if BUSY or DRQ is
set, and this is checked _after_ ide_bus_exec_cmd() has returned.
handle_cmd() will return -1, so check_cmd() will not clear PxCI.
When the async callback calls ide_cmd_done() (which will call
ahci_cmd_done()), it will see that busy_slot is set, and
ahci_cmd_done() will clear PxCI.
This seems racy, since busy_slot is set _after_ ide_bus_exec_cmd() has
returned. The callback might come before busy_slot gets set. And it is
quite confusing that ahci_cmd_done() will be called for all non-NCQ
commands when the command is done, but will only clear PxCI in certain
cases, even though it will always write a D2H FIS and raise an IRQ.
Even worse, in the case where ahci_cmd_done() does not clear PxCI, it
still raises an IRQ. Host software might thus read an old PxCI value,
since PxCI is cleared (by check_cmd()) after the IRQ has been raised.
Try to simplify this by always setting busy_slot for non-NCQ commands,
such that ahci_cmd_done() will always be responsible for clearing PxCI
for non-NCQ commands.
For NCQ commands, clear PxCI when we receive the D2H FIS, but before
raising the IRQ, see AHCI 1.3.1, section 5.3.8, states RegFIS:Entry and
RegFIS:ClearCI.
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Message-id: 20230609140844.202795-5-nks@flawful.org
Signed-off-by: John Snow <jsnow@redhat.com>
The way that BUSY + PxCI is cleared for NCQ (FPDMA QUEUED) commands is
described in SATA 3.5a Gold:
11.15 FPDMA QUEUED command protocol
DFPDMAQ2: ClearInterfaceBsy
"Transmit Register Device to Host FIS with the BSY bit cleared to zero
and the DRQ bit cleared to zero and Interrupt bit cleared to zero to
mark interface ready for the next command."
PxCI is currently cleared by handle_cmd(), but we don't write the D2H
FIS to the FIS Receive Area that actually caused PxCI to be cleared.
Similar to how ahci_pio_transfer() calls ahci_write_fis_pio() with an
additional parameter to write a PIO Setup FIS without raising an IRQ,
add a parameter to ahci_write_fis_d2h() so that ahci_write_fis_d2h()
also can write the FIS to the FIS Receive Area without raising an IRQ.
Change process_ncq_command() to call ahci_write_fis_d2h() without
raising an IRQ (similar to ahci_pio_transfer()), such that the FIS
Receive Area is in sync with the PxTFD shadow register.
E.g. Linux reads status and error fields from the FIS Receive Area
directly, so it is wise to keep the FIS Receive Area and the PxTFD
shadow register in sync.
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Message-id: 20230609140844.202795-4-nks@flawful.org
Signed-off-by: John Snow <jsnow@redhat.com>
Currently, the first time sending an unsupported command
(e.g. READ LOG DMA EXT) will not have ERR_STAT set in the completion.
Sending the unsupported command again, will correctly have ERR_STAT set.
When ide_cmd_permitted() returns false, it calls ide_abort_command().
ide_abort_command() first calls ide_transfer_stop(), which will call
ide_transfer_halt() and ide_cmd_done(), after that ide_abort_command()
sets ERR_STAT in status.
ide_cmd_done() for AHCI will call ahci_write_fis_d2h() which writes the
current status in the FIS, and raises an IRQ. (The status here will not
have ERR_STAT set!).
Thus, we cannot call ide_transfer_stop() before setting ERR_STAT, as
ide_transfer_stop() will result in the FIS being written and an IRQ
being raised.
The reason why it works the second time, is that ERR_STAT will still
be set from the previous command, so when writing the FIS, the
completion will correctly have ERR_STAT set.
Set ERR_STAT before writing the FIS (calling cmd_done), so that we will
raise an error IRQ correctly when receiving an unsupported command.
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20230609140844.202795-3-nks@flawful.org
Signed-off-by: John Snow <jsnow@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Message-ID: <20230823065335.1919380-14-mjt@tls.msk.ru>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
According to the 82371FB documentation (82371FB.pdf, 2.3.9. BMIBA-BUS
MASTER INTERFACE BASE ADDRESS REGISTER, April 1997), the register is
32bit wide. To properly reset it to default values, all 32bit need to be
cleared. Bit #0 "Resource Type Indicator (RTE)" needs to be enabled.
The initial change wrote just the lower 8 bit, leaving parts of the "Bus
Master Interface Base Address" address at bit 15:4 unchanged.
Fixes: e6a71ae327 ("Add support for 82371FB (Step A1) and Improved support for 82371SB (Function 1)")
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Reviewed-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20230712074721.14728-1-olaf@aepfle.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The modern, declarative way to set up VM state handling is to assign to
DeviceClass::vmsd attribute.
There shouldn't be any change in behavior since dc->vmsd causes
vmstate_register_with_alias_id() to be called on the instance during
the instance init phase. vmstate_register() was also called during the
instance init phase which forwards to vmstate_register_with_alias_id()
internally. Checking the migration schema before and after this patch confirms:
before:
> qemu-system-x86_64 -S
> qemu > migrate -d exec:cat>before.mig
after:
> qemu-system-x86_64 -S
> qemu > migrate -d exec:cat>after.mig
> analyze-migration.py -d desc -f before.mig > before.json
> analyze-migration.py -d desc -f after.mig > after.json
> diff before.json after.json
-> empty
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Message-Id: <20230531211043.41724-8-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Message-Id: <20230531211043.41724-7-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Every TYPE_PCI_IDE device performs the same not-so-trivial bit manipulation by
copy'n'paste code. Extract this into bmdma_status_writeb(), mirroring
bmdma_cmd_writeb().
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-Id: <20230531211043.41724-6-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Every invocation of bmdma_init() is followed by `d->bmdma[i].bus = &d->bus[i]`.
Resolve this redundancy by extracting it into bmdma_init().
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20230531211043.41724-5-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Resolves circular depencency between IDE function and south bridge.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20230531211043.41724-3-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Exposing the legacy IDE interrupts as GPIOs allows them to be connected in the
parent device through qdev_connect_gpio_out(), i.e. without accessing private
data of TYPE_PCI_IDE.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20230531211043.41724-2-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
We use the user_ss[] array to hold the user emulation sources,
and the softmmu_ss[] array to hold the system emulation ones.
Hold the latter in the 'system_ss[]' array for parity with user
emulation.
Mechanical change doing:
$ sed -i -e s/softmmu_ss/system_ss/g $(git grep -l softmmu_ss)
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20230613133347.82210-10-philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
This backslash obviously does not belong here, so remove it.
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: John Snow <jsnow@redhat.com>
Message-Id: <20230601134434.519805-2-nks@flawful.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
This protects devices from bh->mmio reentrancy issues.
Thanks: Thomas Huth <thuth@redhat.com> for diagnosing OS X test failure.
Signed-off-by: Alexander Bulekov <alxndr@bu.edu>
Reviewed-by: Darren Kenny <darren.kenny@oracle.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Paul Durrant <paul@xen.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20230427211013.2994127-5-alxndr@bu.edu>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Bring the block files in line with the QEMU coding style, with spaces
for indentation. This patch partially resolves the issue 371.
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/371
Signed-off-by: Yeqi Fu <fufuyqqqqqq@gmail.com>
Message-Id: <20230315043229.62100-1-fufuyqqqqqq@gmail.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: John Snow <jsnow@redhat.com>
Message-Id: <20210511041848.2743312-5-f4bug@amsat.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230215112712.23110-21-philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230215112712.23110-20-philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230215112712.23110-19-philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
The function is only used inside ide/pci.c, so doesn't need to be exported.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230215112712.23110-18-philmd@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230215112712.23110-17-philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
idebus_active_if() operates on a IDEBus; rename it as
ide_bus_active_if() to emphasize its first argument
is a IDEBus.
Mechanical change using:
$ sed -i -e 's/idebus_active_if/ide_bus_active_if/g' \
$(git grep -l idebus_active_if)
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230215112712.23110-16-philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
ide_init2() initializes a IDEBus, and set its output IRQ.
To emphasize this, rename it as ide_bus_init_output_irq().
Mechanical change using:
$ sed -i -e 's/ide_init2/ide_bus_init_output_irq/g' \
$(git grep -l ide_init2)
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230215112712.23110-15-philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
ide_exec_cmd() operates on a IDEBus; rename it as
ide_bus_exec_cmd() to emphasize its first argument
is a IDEBus.
Mechanical change using:
$ sed -i -e 's/ide_exec_cmd/ide_bus_exec_cmd/g' \
$(git grep -wl ide_exec_cmd)
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230215112712.23110-14-philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
ide_register_restart_cb() operates on a IDEBus; rename it as
ide_bus_register_restart_cb() to emphasize its first argument
is a IDEBus.
Mechanical change using:
$ sed -i -e 's/ide_register_restart_cb/ide_bus_register_restart_cb/g' \
$(git grep -l ide_register_restart_cb)
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230215112712.23110-13-philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
ide_create_drive() operates on a IDEBus; rename it as
ide_bus_create_drive() to emphasize its first argument
is a IDEBus.
Mechanical change using:
$ sed -i -e 's/ide_create_drive/ide_bus_create_drive/g' \
$(git grep -wl ide_create_drive)
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230215112712.23110-12-philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
ide_set_irq() operates on a IDEBus; rename it as
ide_bus_set_irq() to emphasize its first argument
is a IDEBus.
Mechanical change using:
$ sed -i -e 's/ide_set_irq/ide_bus_set_irq/g' \
$(git grep -l ide_set_irq)
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230215112712.23110-11-philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Only include "hw/irq.h" where appropriate.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230215112712.23110-10-philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Only atapi.c requires the SCSI constants. No need to include
it in all files including "hw/ide/internal.h".
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230215112712.23110-7-philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
The intermediate ISAIDEState::irq variable just add noise, remove it.
Message-Id: <20230215112712.23110-6-philmd@linaro.org>
Reviewed-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
"hw/ide.h" is a mixed bag of lost IDE declarations.
Extract isa_ide_init() and the TYPE_ISA_IDE QOM declarations
to a new "hw/ide/isa.h" header.
Rename ISAIDEState::isairq as 'irqnum' to emphasize this is
not a qemu_irq object but the number (index) of an ISA IRQ.
Message-Id: <20230215112712.23110-5-philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Bernhard Beschow <shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
"hw/ide.h" is a mixed bag of lost IDE declarations.
Extract mmio_ide_init_drives() and the TYPE_MMIO_IDE QOM
declarations to a new "hw/ide/mmio.h" header.
Document the SysBus interface.
Message-Id: <20230215112712.23110-4-philmd@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Following docs/devel/style.rst guidelines, rename MMIOIDEState
as IdeMmioState.
Having the structure name and its typedef named equally,
we can manually convert from the old DECLARE_INSTANCE_CHECKER()
macro to the more recent OBJECT_DECLARE_SIMPLE_TYPE().
Note, due to that name mismatch, this macro wasn't automatically
converted during commit 8063396bf3 ("Use OBJECT_DECLARE_SIMPLE_TYPE
when possible").
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20230220091358.17038-3-philmd@linaro.org>
Fixes: e4baa9f00b ("AHCI: Replace DPRINTF with trace-events")
Signed-off-by: Fiona Ebner <f.ebner@proxmox.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <20230217103130.42077-1-f.ebner@proxmox.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
