Instead of using error_report() to print guest errors let's use
qemu_log_mask(LOG_GUEST_ERROR,...) to log the error.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
This patch fixes four different things, to maintain bisectability they
have been merged into a single patch. The following fixes are below:
sifive_plic: Fix incorrect irq calculation
The irq is incorrectly calculated to be off by one. It has worked in the
past as the priority_base offset has also been set incorrectly. We are
about to fix the priority_base offset so first first the irq
calculation.
sifive_u: Fix PLIC priority base offset and numbering
According to the FU540 manual the PLIC source priority address starts at
an offset of 0x04 and not 0x00. The same manual also specifies that the
PLIC only has 53 source priorities. Fix these two incorrect header
files.
We also need to over extend the plic_gpios[] array as the PLIC sources
count from 1 and not 0.
riscv: sifive_e: Fix PLIC priority base offset
According to the FE31 manual the PLIC source priority address starts at
an offset of 0x04 and not 0x00.
riscv: virt: Fix PLIC priority base offset
Update the virt offsets based on the newly updated SiFive U and SiFive E
offsets.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
The UART0's interrupt vector is wrongly set to 1 in the device tree.
Use SIFIVE_U_UART0_IRQ instead.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
At present the sifive uart model only generates RX interrupt. This
updates it to generate TX interrupt so that it is more useful.
Note the TX fifo is still unimplemented.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
We can't allow the supervisor to control SEIP as this would allow the
supervisor to clear a pending external interrupt which will result in
lost a interrupt in the case a PLIC is attached. The SEIP bit must be
hardware controlled when a PLIC is attached.
This logic was previously hard-coded so SEIP was always masked even
if no PLIC was attached. This patch adds riscv_cpu_claim_interrupts
so that the PLIC can register control of SEIP. In the case of models
without a PLIC (spike), the SEIP bit remains software controlled.
This interface allows for hardware control of supervisor timer and
software interrupts by other interrupt controller models.
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Sagar Karandikar <sagark@eecs.berkeley.edu>
Cc: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Cc: Alistair Francis <Alistair.Francis@wdc.com>
Signed-off-by: Michael Clark <mjc@sifive.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
The mode variable only uses the lower 4-bits (M,H,S,U) so
replace the GCC specific __builtin_popcount with ctpop8.
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Sagar Karandikar <sagark@eecs.berkeley.edu>
Cc: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Cc: Alistair Francis <Alistair.Francis@wdc.com>
Signed-off-by: Michael Clark <mjc@sifive.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Not all interrupt controllers have a working implementation of
message-signalled interrupts; in some cases, the guest may expect
MSI to work but it won't due to the buggy or lacking emulation.
In QEMU this is represented by the "msi_nonbroken" variable. This
patch adds a new configuration symbol enabled whenever the binary
contains an interrupt controller that will set "msi_nonbroken". We
can then use it to remove devices that cannot be possibly added
to the machine, because they require MSI.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Set msi_nonbroken as true for the PLIC.
According to the comment located here:
https://git.qemu.org/?p=qemu.git;a=blob;f=hw/pci/msi.c;h=47d2b0f33c664533b8dbd5cb17faa8e6a01afe1f;hb=HEAD#l38
the msi_nonbroken variable should be set to true even if they don't
support MSI. In this case that is what we are doing as we don't support
MSI.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reported-by: Andrea Bolognani <abologna@redhat.com>
Reported-by: David Abdurachmanov <david.abdurachmanov@gmail.com>
Message-Id: <256afbb2da005dc62c159b0f4a4fc0d95c050660.1552679970.git.alistair.francis@wdc.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Re-enable PCI_DEVICES for RISC-V.
The patch is based on other <arch>/Kconfig.
Signed-off-by: David Abdurachmanov <david.abdurachmanov@gmail.com>
Fixes: 82a230d5a3 ("riscv-softmmu.mak: replace CONFIG_* with Kconfig "select" directives")
Message-Id: <20190311091256.18385-1-david.abdurachmanov@gmail.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The Kconfig files were generated mostly with this script:
for i in `grep -ho CONFIG_[A-Z0-9_]* default-configs/* | sort -u`; do
set fnord `git grep -lw $i -- 'hw/*/Makefile.objs' `
shift
if test $# = 1; then
cat >> $(dirname $1)/Kconfig << EOF
config ${i#CONFIG_}
bool
EOF
git add $(dirname $1)/Kconfig
else
echo $i $*
fi
done
sed -i '$d' hw/*/Kconfig
for i in hw/*; do
if test -d $i && ! test -f $i/Kconfig; then
touch $i/Kconfig
git add $i/Kconfig
fi
done
Whenever a symbol is referenced from multiple subdirectories, the
script prints the list of directories that reference the symbol.
These symbols have to be added manually to the Kconfig files.
Kconfig.host and hw/Kconfig were created manually.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Message-Id: <20190123065618.3520-27-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Cast the kernel start address to the target bit length.
This ensures that we calculate the initrd offset to a valid address for
the architecture.
Steps to reproduce the original problem (reported by Alex):
Build U-Boot for the virt machine for riscv32. Then run it with
$ qemu-system-riscv32 -M virt -kernel u-boot -nographic -initrd <a file>
You can find the initrd address with
U-Boot# fdt addr $fdtcontroladdr
U-Boot# fdt ls /chosen
Then take a peek at that address:
U-Boot# md.b <addr>
and you will see that there is nothing there without this patch. The
reason is that the binary was loaded to a negative address.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Suggested-by: Alexander Graf <agraf@suse.de>
Reported-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Add the new configs to default-configs/riscv*-sofmmu.mak.
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190202072456.6468-19-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch adds an optional function pointer, 'elf_note_fn', to
load_elf() which causes load_elf() to additionally parse any
ELF program headers of type PT_NOTE and check to see if the ELF
Note is of the type specified by the 'translate_opaque' arg.
If a matching ELF Note is found then the specfied function pointer
is called to process the ELF note.
Passing a NULL function pointer results in ELF Notes being skipped.
The first consumer of this functionality is the PVHboot support
which needs to read the XEN_ELFNOTE_PHYS32_ENTRY ELF Note while
loading the uncompressed kernel binary in order to discover the
boot entry address for the x86/HVM direct boot ABI.
Signed-off-by: Liam Merwick <liam.merwick@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The watermark bits are set in the interrupt pending register according
to the configuration of txcnt and rxcnt in the txctrl and rxctrl
registers.
Since the UART TX does not implement a FIFO, the txwm bit is set as long
as the TX watermark level is greater than zero.
Signed-off-by: Nathaniel Graff <nathaniel.graff@sifive.com>
Reviewed-by: Michael Clark <mjc@sifive.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Previously the second UARTs on the sifive_e and sifive_u machines
where disabled due to check-qtest-riscv32 and check-qtest-riscv64
failures. Recent changes in the QEMU core serial code have
resolved these failures so the second UARTs can be instantiated.
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Sagar Karandikar <sagark@eecs.berkeley.edu>
Cc: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Cc: Alistair Francis <Alistair.Francis@wdc.com>
Signed-off-by: Michael Clark <mjc@sifive.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
The address calculation for the pending bitfield had
a copy paste bug. This bug went unnoticed because the Linux
PLIC driver does not read the pending bitfield, rather it
reads pending interrupt numbers from the claim register
and writes acknowledgements back to the claim register.
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Sagar Karandikar <sagark@eecs.berkeley.edu>
Cc: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Cc: Alistair Francis <Alistair.Francis@wdc.com>
Reported-by: Vincent Siles <vincent.siles@ens-lyon.org>
Signed-off-by: Michael Clark <mjc@sifive.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
A missing shift made updates to the low order bits
of timecmp erroneously copy the old low order bits
into the high order bits of the 64-bit timecmp
register. Add the missing shift and rename timecmp
local variables to timecmp_hi and timecmp_lo.
This bug didn't show up as the low order bits are
usually written first followed by the high order
bits meaning the high order bits contained an invalid
value between the timecmp_lo and timecmp_hi update.
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Sagar Karandikar <sagark@eecs.berkeley.edu>
Cc: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Cc: Alistair Francis <Alistair.Francis@wdc.com>
Co-Authored-by: Johannes Haring <johannes.haring@gmx.net>
Signed-off-by: Michael Clark <mjc@sifive.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
The 'clock-frequency' DT property is required by U-Boot to compute
the divider value. This patch sets the 'clock-frequency' DT property
of the SiFive UART device tree node (similar to virt machine).
Signed-off-by: Anup Patel <anup@brainfault.org>
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Connect the gpex PCIe device based on the device tree included in the
HiFive Unleashed ROM.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Andrea Bolognani <abologna@redhat.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Coverity caught a malloc() call that was never freed. This patch ensures
that we free the memory but also updates the allocation to use
g_strdup_printf() instead of malloc().
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Michael Clark <mjc@sifive.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Michael Clark <mjc@sifive.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Change the API of riscv_set_local_interrupt to take a
write mask and value to allow setting and clearing of
multiple local interrupts atomically in a single call.
Rename the new function to riscv_cpu_update_mip.
Signed-off-by: Michael Clark <mjc@sifive.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
error_report and friends already add a "qemu-system-xxx" prefix
to the string, so a "qemu:" prefix is redundant in the string.
Just drop it.
Reported-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Mao Zhongyi <maozhongyi@cmss.chinamobile.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <1537495530-580-1-git-send-email-maozhongyi@cmss.chinamobile.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
To allow Linux to enumerate devices on the /soc/ node set it as a
"simple-bus".
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
The PLIC previously used a mutex to protect against concurrent
access to the claimed and pending bitfields. Instead of using
a mutex, we update the bitfields using atomic_cmpxchg.
Rename sifive_plic_num_irqs_pending to sifive_plic_irqs_pending
and add an early out if any interrupts are pending as the
count of pending interrupts is not used.
Cc: Sagar Karandikar <sagark@eecs.berkeley.edu>
Cc: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Alistair Francis <Alistair.Francis@wdc.com>
Signed-off-by: Michael Clark <mjc@sifive.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Use the new object_initialize_child() and sysbus_init_child_obj() to
fix the issue.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Suggested-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Michael Clark <mjc@sifive.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Use the new object_initialize_child() and sysbus_init_child_obj() to
fix the issue.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Suggested-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Michael Clark <mjc@sifive.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Use the new object_initialize_child() and sysbus_init_child_obj() to
fix the issue.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Suggested-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Michael Clark <mjc@sifive.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Use the new object_initialize_child() and sysbus_init_child_obj() to
fix the issue.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Suggested-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Michael Clark <mjc@sifive.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Use the new object_initialize_child() and sysbus_init_child_obj() to
fix the issue.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Suggested-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Michael Clark <mjc@sifive.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Connect the Cadence GEM ethernet device. This also requires us to
expose the plic interrupt lines.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Michael Clark <mjc@sifive.com>
Set the interrupt-controller ndev to the correct number taken from the
HiFive Unleashed board.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Michael Clark <mjc@sifive.com>
To allow Linux to ennumerate devices on the /soc/ node set it as a
"simple-bus".
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Michael Clark <mjc@sifive.com>
Instead of creating the interrupt in lines with qemu_allocate_irq() use
qdev_init_gpio_in() as this gives us the ability to use the qdev*gpio*()
helpers later on.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Suggested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Michael Clark <mjc@sifive.com>
Create a SiFive Unleashed U54 SoC and use that in the sifive_u machine.
We leave the SoC, RAM, device tree and reset/fdt loading as part of the
machine. All the other device creation has been moved to the SoC.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Michael Clark <mjc@sifive.com>
It eases code review, unit is explicit.
Patch generated using:
$ git grep -E '(1024|2048|4096|8192|(<<|>>).?(10|20|30))' hw/ include/hw/
and modified manually.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Michael Clark <mjc@sifive.com>
Message-Id: <20180625124238.25339-17-f4bug@amsat.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
* Require libfdt when configuring for 'riscv*-softmmu'
* Increase HTIF priority and allow zero base address
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQR8mZMOsXzYugc9Xvpr8dezV+8+TwUCWvLKRQAKCRBr8dezV+8+
TyOrAKCBiArCoNOD0lIvSdgu8Dv7dKOUaQCeMfS/FkM9wSTOnZgOPKPEZ3xreLY=
=wUet
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/riscv/tags/riscv-qemu-2.13-minor-fixes-3' into staging
RISC-V: QEMU 2.13 Minor Fixes
* Require libfdt when configuring for 'riscv*-softmmu'
* Increase HTIF priority and allow zero base address
# gpg: Signature made Wed 09 May 2018 11:15:33 BST
# gpg: using DSA key 6BF1D7B357EF3E4F
# gpg: Good signature from "Michael Clark <michaeljclark@mac.com>"
# gpg: aka "Michael Clark <mjc@sifive.com>"
# gpg: aka "Michael Clark <michael@metaparadigm.com>"
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 7C99 930E B17C D8BA 073D 5EFA 6BF1 D7B3 57EF 3E4F
* remotes/riscv/tags/riscv-qemu-2.13-minor-fixes-3:
riscv: requires libfdt
riscv: htif: increase the priority of the htif subregion
riscv: spike: allow base == 0
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Alistair Francis
Peter Maydell
Bin Meng
Michael Clark
Paolo Bonzini
David Abdurachmanov
Yang Zhong
Liam Merwick
Nathaniel Graff
Anup Patel
Mao Zhongyi
Philippe Mathieu-Daudé
KONRAD Frederic