sed's -E option may not be supported by older distros. As there's no
point using sed here at all, use just shell mechanisms to establish the
variable values, starting from the stem instead of the full target.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
The make rules for building QEMU are mostly silent by default. They can
be made verbose by setting the variable V=1. The default state does not
however correspond to a V=0 setting - $(V) must be undefined / empty to
get the default quiet build.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-Id: <20180123164718.12714-3-berrange@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This reverts commit 42a77f1ce4.
The primary intention of this change was to silence messages
like
make[1]: '/home/berrange/src/virt/qemu/capstone/libcapstone.a' is up to date.
which we get when calling make recursively with explicit
targets.
The problem is that this change affected every make target,
not merely the targets that triggered these "is up to date"
messages. As a result any targets that were not invoking
commands via "$(call quiet-command ...)" suddenly become
silent. This is particularly bad for "make install" which
now appears todo nothing.
Rather than go through every make rule and try to identify
places where we now need to explicitly print a message to
show work taking place, just revert the change.
To address the original problem of silencing "is up to date"
messages, we simply add --quiet to the SUBDIR_MAKEVARS
variable, so it only affects us on recursive make calls.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-Id: <20180123164718.12714-2-berrange@redhat.com>
Tested-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Python2 did not validate locale correctness when reading input data, so
would happily read UTF-8 data in non-UTF-8 locales. Python3 is strict so
if you try to read UTF-8 data in the C locale, it will raise an error
for any UTF-8 bytes that aren't representable in 7-bit ascii encoding.
e.g.
UnicodeDecodeError: 'ascii' codec can't decode byte 0xc3 in position 54: ordinal not in range(128)
Traceback (most recent call last):
File "/tmp/qemu-test/src/scripts/qapi-commands.py", line 317, in <module>
schema = QAPISchema(input_file)
File "/tmp/qemu-test/src/scripts/qapi.py", line 1468, in __init__
parser = QAPISchemaParser(open(fname, 'r'))
File "/tmp/qemu-test/src/scripts/qapi.py", line 301, in __init__
previously_included)
File "/tmp/qemu-test/src/scripts/qapi.py", line 348, in _include
exprs_include = QAPISchemaParser(fobj, previously_included, info)
File "/tmp/qemu-test/src/scripts/qapi.py", line 271, in __init__
self.src = fp.read()
File "/usr/lib64/python3.5/encodings/ascii.py", line 26, in decode
return codecs.ascii_decode(input, self.errors)[0]
More background on this can be seen in
https://www.python.org/dev/peps/pep-0538/
Many distros support a new C.UTF-8 locale that is like the C locale,
but with UTF-8 instead of 7-bit ASCII. That is not entirely portable
though. This patch thus sets the LANG to "C", but overrides LC_CTYPE
to be en_US.UTF-8 locale. This gets us pretty close to C.UTF-8, but
in a way that should be portable to everywhere QEMU builds.
This patch only forces UTF-8 for QAPI scripts, since that is the one
showing the immediate error under Python3 with C locale, but potentially
we ought to force this for all python scripts used in the build process.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-Id: <20180116134217.8725-9-berrange@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
The qcode-to-linux keymaps was accidentally added in the wrong place
by
commit de80d78594
Author: Owen Smith <owen.smith@citrix.com>
Date: Fri Nov 3 11:56:28 2017 +0000
ui: generate qcode to linux mappings
breaking the alphabetical ordering of keymaps
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180117164118.8510-4-berrange@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Replace the qcode_to_keycode table with automatically
generated tables.
Missing entries in qcode_to_keycode now fixed:
- Q_KEY_CODE_KP_COMMA -> 0x2d
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 20180117164118.8510-3-berrange@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Replace the qcode_to_keycode_set1, qcode_to_keycode_set2,
and qcode_to_keycode_set3 tables with automatically
generated tables.
Missing entries in qcode_to_keycode_set1 now fixed:
- Q_KEY_CODE_SYSRQ -> 0x54
- Q_KEY_CODE_PRINT -> 0x54 (NB ignored due to special case)
- Q_KEY_CODE_AGAIN -> 0xe005
- Q_KEY_CODE_PROPS -> 0xe006
- Q_KEY_CODE_UNDO -> 0xe007
- Q_KEY_CODE_FRONT -> 0xe00c
- Q_KEY_CODE_COPY -> 0xe078
- Q_KEY_CODE_OPEN -> 0x64
- Q_KEY_CODE_PASTE -> 0x65
- Q_KEY_CODE_CUT -> 0xe03c
- Q_KEY_CODE_LF -> 0x5b
- Q_KEY_CODE_HELP -> 0xe075
- Q_KEY_CODE_COMPOSE -> 0xe05d
- Q_KEY_CODE_PAUSE -> 0xe046
- Q_KEY_CODE_KP_EQUALS -> 0x59
And some mistakes corrected:
- Q_KEY_CODE_HIRAGANA was mapped to 0x70 (Katakanahiragana)
instead of of 0x77 (Hirigana)
- Q_KEY_CODE_MENU was incorrectly mapped to the compose
scancode (0xe05d) and is now mapped to 0xe01e
- Q_KEY_CODE_FIND was mapped to 0xe065 (Search) instead
of to 0xe041 (Find)
- Q_KEY_CODE_POWER, SLEEP & WAKE had 0x0e instead of 0xe0
as the prefix
Missing entries in qcode_to_keycode_set2 now fixed:
- Q_KEY_CODE_PRINT -> 0x7f (NB ignored due to special case)
- Q_KEY_CODE_COMPOSE -> 0xe02f
- Q_KEY_CODE_PAUSE -> 0xe077
- Q_KEY_CODE_KP_EQUALS -> 0x0f
And some mistakes corrected:
- Q_KEY_CODE_HIRAGANA was mapped to 0x13 (Katakanahiragana)
instead of of 0x62 (Hirigana)
- Q_KEY_CODE_MENU was incorrectly mapped to the compose
scancode (0xe02f) and is now not mapped
- Q_KEY_CODE_FIND was mapped to 0xe010 (Search) and is now
not mapped.
- Q_KEY_CODE_POWER, SLEEP & WAKE had 0x0e instead of 0xe0
as the prefix
Missing entries in qcode_to_keycode_set3 now fixed:
- Q_KEY_CODE_ASTERISK -> 0x7e
- Q_KEY_CODE_SYSRQ -> 0x57
- Q_KEY_CODE_LESS -> 0x13
- Q_KEY_CODE_STOP -> 0x0a
- Q_KEY_CODE_AGAIN -> 0x0b
- Q_KEY_CODE_PROPS -> 0x0c
- Q_KEY_CODE_UNDO -> 0x10
- Q_KEY_CODE_COPY -> 0x18
- Q_KEY_CODE_OPEN -> 0x20
- Q_KEY_CODE_PASTE -> 0x28
- Q_KEY_CODE_FIND -> 0x30
- Q_KEY_CODE_CUT -> 0x38
- Q_KEY_CODE_HELP -> 0x09
- Q_KEY_CODE_COMPOSE -> 0x8d
- Q_KEY_CODE_AUDIONEXT -> 0x93
- Q_KEY_CODE_AUDIOPREV -> 0x94
- Q_KEY_CODE_AUDIOSTOP -> 0x98
- Q_KEY_CODE_AUDIOMUTE -> 0x9c
- Q_KEY_CODE_VOLUMEUP -> 0x95
- Q_KEY_CODE_VOLUMEDOWN -> 0x9d
- Q_KEY_CODE_CALCULATOR -> 0xa3
- Q_KEY_CODE_AC_HOME -> 0x97
And some mistakes corrected:
- Q_KEY_CODE_MENU was incorrectly mapped to the compose
scancode (0x8d) and is now 0x91
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 20180117164118.8510-2-berrange@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The x_keycode_to_pc_keycode and evdev_keycode_to_pc_keycode
tables are replaced with automatically generated tables.
In addition the X11 heuristics are improved to detect running
on XQuartz and XWin X11 servers, to activate the correct OS-X
and Win32 keycode maps.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 20180117164717.15855-3-berrange@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
This commit introduces a vhost-user-blk backend device, it uses UNIX
domain socket to communicate with QEMU. The vhost-user-blk sample
application should be used with QEMU vhost-user-blk-pci device.
To use it, complie with:
make vhost-user-blk
and start like this:
vhost-user-blk -b /dev/sdb -s /path/vhost.socket
Signed-off-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Move generic make flags in MAKEFLAGS (SUBDIR_MAKEFLAGS is more qemu specific).
Use --quiet to silence make 'is up to date' message.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Tested-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20180104160523.22995-3-marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
These targets don't need a full build of git submodules.
(See b8e535ae8a and eaa2ddbb76).
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
For some systems (i.e. FreeBSD) the default 'make' is not compatible with the
GNU extensions used by QEMU makefiles.
Calling the GNU make (gmake) works, however the help displayed refers to the
host 'make' and copy/paste leads to lot of unobvious errors:
$ gmake check-help
[...]
make check Run all tests
$ make check
make: "Makefile" line 28: Missing dependency operator
make: "Makefile" line 37: Need an operator
make: "Makefile" line 41: warning: duplicate script for target "git-submodule-update" ignored
make: "rules.mak" line 70: warning: duplicate script for target "%.o" ignored
make: Unknown modifier ' '
make: Unclosed substitution for eval modules (= missing)
make: "tests/Makefile.include" line 24: Variable/Value missing from "export"
make: "tests/" line 1: warning: Zero byte read from file, skipping rest of line.
make: "tests/" line 1: Need an operator
make: "Makefile" line 660: warning: duplicate script for target "ifneq" ignored
make: "Makefile" line 78: warning: using previous script for "ifneq" defined here
make: Fatal errors encountered -- cannot continue
Using the $(MAKE) variable, the help displayed is consistent with the 'make'
program used.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Use keycodedb to generate a qcode to linux mapping
Signed-off-by: Owen Smith <owen.smith@citrix.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Stefano Stabellini <sstabellini@kernel.org>
Developers sometimes mistakenly run 'make test' instead of 'make check'.
'make test' triggers the ancient, unmaintained tcg unit tests in
tests/tcg/Makefile which have long since ceased compiling.
Even if someone fixes the TCG tests, it makes little sense to put
them in a 'make test' target, rather they should be 'make check-tcg',
possibly wired up as a dependency of 'make check'.
In the meantime, this patch disarms the 'make test' trap by simply
deleting it so users get an immediate error. This should be enough
for them to remember to type 'make check' instead (or 'make help'
to learn). It also deletes 'make speed' which is another route
into the tcg tests.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Reviewed-by: Kashyap Chamarthy <kchamart@redhat.com>
Reviewed-by: Daniel Henrique Barboza <danielhb@linux.vnet.ibm.com>
Message-id: 20171121142538.22072-1-berrange@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Using obscure black magic introduced in eaa2ddbb76 :)
In an out-of-tree directory, running "../configure && make help" will generate
some required files (.mak), then clone some submodules, compile at least
the capstone submodule, generate QMP and Trace files, and finally display
the help.
On an outdated computer (Sun Blade workstation), running "make help" took
more than 5h :) With this patch it took roughly 37min.
Suggested-by: Daniel P. Berrange <berrange@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20171108032052.20029-1-f4bug@amsat.org>
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Daniel P. Berrange <berrange@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When cross compiling QEMU for Windows we need to specify the cross
version of ranlib to avoid build errors when building capstone. This
patch ensures we use the same cross prefix on ranlib as other toolchain
components.
- Fedora23 mingw
- RHEL-7.2 with mingw packages from epel:
LINK qemu-img.exe
build-win64/capstone/capstone.lib: error adding symbols: Archive has no
index; run ranlib to add one
collect2: error: ld returned 1 exit status
$ x86_64-w64-mingw32-ar --version
GNU ar (GNU Binutils) 2.25
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Daniel P. Berrange <berrange@redhat.com>
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <e457d4e906dceea4de6c3431813a06b137c1ab9c.1510103351.git.alistair.francis@xilinx.com>
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
The Makefile attempts to optimize the handling of submodules by using MAKELEVEL
to only check the submodule status when running from the top level make
invokation. This causes problems for people who are using a makefile of their
own to in turn invoke QEMU's makefile, as MAKELEVEL is already set to 1 (or
more) when QEMU's makefile runs.
This optimization should not really be needed, since the git-submodule.sh
script is already used to detect if a submodule update is required. This by
removing the MAKELEVEL check, we at most add an extra 'git-submodule.sh status'
call to each make level, the overhead of which is lost in noise of building
QEMU.
Reviewed-by: Greg Kurz <groug@kaod.org>
Tested-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Some people building QEMU use VPATH builds where the source directory is on a
read-only volume. In such a case 'scripts/git-submodules.sh update' will always
fail and users are required to run it manually themselves on their original
writable source directory.
While this is already supported, it is nice to give users a command line flag
to configure to permanently disable automatic submodule updates, as it means
they won't get hard to diagnose failures from git-submodules.sh at an arbitrary
later date.
This patch thus introduces a flag '--disable-git-update' which will prevent
'make' from ever running 'scripts/git-submodules.sh update'. It will still run
the 'status' command to determine if a submodule update is needed, but when it
does this it'll simply stop and print a message instructing the developer what
todo. eg
$ ./configure --target-list=x86_64-softmmu --disable-git-update
...snip...
$ make
GEN config-host.h
GEN trace/generated-tcg-tracers.h
GEN trace/generated-helpers-wrappers.h
GEN trace/generated-helpers.h
GEN trace/generated-helpers.c
GEN module_block.h
GIT submodule checkout is out of date. Please run
scripts/git-submodule.sh update ui/keycodemapdb
from the source directory checkout /home/berrange/src/virt/qemu
make: *** [Makefile:31: git-submodule-update] Error 1
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Some users can't run a bare 'git' command, due to need for a transparent
proxying solution such as 'tsocks'. This adds an argument to configure to
let users specify such a thing:
./configure --with-git="tsocks git"
The submodule script is also updated to give the user a hint about using this
flag, if we fail to checkout modules.
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Do not require the submodule, but use it if present. Allow the
command-line to override system or git submodule either way.
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
This was introduced by:
commit aef45d51d1
Author: Daniel P. Berrange <berrange@redhat.com>
Date: Fri Sep 29 11:11:56 2017 +0100
build: automatically handle GIT submodule checkout for dtc
On my system, I see the following with a fresh clone:
% ./configure --disable-gtk --target-list=aarch64-softmmu
% make -j8
GEN aarch64-softmmu/config-devices.mak.tmp
GEN config-host.h
mkdir -p dtc/libfdt
GIT ui/keycodemapdb dtc
mkdir -p dtc/tests
GEN qemu-options.def
[snip]
GEN migration/trace.h
make: *** [git-submodule-update] Error 1
make: *** Waiting for unfinished jobs....
Upon closer inspection, the root cause of the error is:
% git submodule update --init ui/keycodemapdb dtc
fatal: destination path 'dtc' already exists and is not an empty directory.
Clone of 'git://git.qemu-project.org/dtc.git' into submodule path 'dtc' failed
This patch fixes this race condition by forcing the 'dtc/%' rule which caused
'dtc' to be non-empty to wait on '.git-submodule-status'.
Signed-off-by: Aaron Lindsay <alindsay@codeaurora.org>
Reviewed-by: Daniel P. Berrange <berrange@redhat.com>
Acked-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 1508352023-28591-1-git-send-email-alindsay@codeaurora.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add vertex shader which flips the texture upside down while blitting it.
Add argument to qemu_gl_run_texture_blit() to enable flipping.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20171010135453.6704-4-kraxel@redhat.com
With the upcoming dmabuf support in qemu there will be more users of the
shaders than just console-gl.c. So rename ConsoleGLState to
QemuGLShader, rename some functions too, move code from console-gl.c to
shaders.c.
No functional change.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20171010135453.6704-3-kraxel@redhat.com
qemu-keymap generates qemu reverse keymaps from xkb keymaps,
which can be used with the qemu "-k" command line switch.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20171005153330.19210-2-kraxel@redhat.com
Replace the number_to_qcode, qcode_to_number and linux_to_qcode
tables with automatically generated tables.
Missing entries in linux_to_qcode now fixed:
KEY_LINEFEED -> Q_KEY_CODE_LF
KEY_KPEQUAL -> Q_KEY_CODE_KP_EQUALS
KEY_COMPOSE -> Q_KEY_CODE_COMPOSE
KEY_AGAIN -> Q_KEY_CODE_AGAIN
KEY_PROPS -> Q_KEY_CODE_PROPS
KEY_UNDO -> Q_KEY_CODE_UNDO
KEY_FRONT -> Q_KEY_CODE_FRONT
KEY_COPY -> Q_KEY_CODE_COPY
KEY_OPEN -> Q_KEY_CODE_OPEN
KEY_PASTE -> Q_KEY_CODE_PASTE
KEY_CUT -> Q_KEY_CODE_CUT
KEY_HELP -> Q_KEY_CODE_HELP
KEY_MEDIA -> Q_KEY_CODE_MEDIASELECT
In addition, some fixes:
- KEY_PLAYPAUSE now maps to Q_KEY_CODE_AUDIOPLAY, instead of
KEY_PLAYCD. KEY_PLAYPAUSE is defined across almost all scancodes
sets, while KEY_PLAYCD only appears in AT set1, so the former is
a more useful mapping.
Missing entries in qcode_to_number now fixed:
Q_KEY_CODE_AGAIN -> 0x85
Q_KEY_CODE_PROPS -> 0x86
Q_KEY_CODE_UNDO -> 0x87
Q_KEY_CODE_FRONT -> 0x8c
Q_KEY_CODE_COPY -> 0xf8
Q_KEY_CODE_OPEN -> 0x64
Q_KEY_CODE_PASTE -> 0x65
Q_KEY_CODE_CUT -> 0xbc
Q_KEY_CODE_LF -> 0x5b
Q_KEY_CODE_HELP -> 0xf5
Q_KEY_CODE_COMPOSE -> 0xdd
Q_KEY_CODE_KP_EQUALS -> 0x59
Q_KEY_CODE_MEDIASELECT -> 0xed
In addition, some fixes:
- Q_KEY_CODE_MENU was incorrectly mapped to the compose
scancode (0xdd) and is now mapped to 0x9e
- Q_KEY_CODE_FIND was mapped to 0xe065 (Search) instead
of to 0xe041 (Find)
- Q_KEY_CODE_HIRAGANA was mapped to 0x70 (Katakanahiragana)
instead of of 0x77 (Hirigana)
- Q_KEY_CODE_PRINT was mapped to 0xb7 which is not a defined
scan code in AT set 1, it is now mapped to 0x54 (sysrq)
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 20170929101201.21039-5-berrange@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The https://gitlab.com/keycodemap/keycodemapdb/ repo contains a
data file mapping between all the different scancode/keycode/keysym
sets that are known, and a tool to auto-generate lookup tables for
different combinations.
It is used by GTK-VNC, SPICE-GTK and libvirt for mapping keys.
Using it in QEMU will let us replace many hand written lookup
tables with auto-generated tables from a master data source,
reducing bugs. Adding new QKeyCodes will now only require the
master table to be updated, all ~20 other tables will be
automatically updated to follow.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 20170929101201.21039-4-berrange@redhat.com
[ kraxel: fix build ]
[ kraxel: switch repo to qemu.git mirror ]
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Currently if DTC is required by configure and not available in the host
OS install, we exit with an error message telling the user to checkout a
git submodule or install the library.
This introduces automatic handling of the git submodule checkout process
and enables it for dtc. This only runs if building from GIT, so users of
release tarballs still need the system library install. The current state
of the git checkout is stashed in .git-submodule-status, and a helper
program is used to determine if this state matches the desired submodule
state. A dependency against 'Makefile' ensures that the submodule state
is refreshed at the start of the build process
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 20170929101201.21039-2-berrange@redhat.com
[ kraxel: use /bin/sh not bash for scripts/git-submodule.sh ]
[ kraxel: fix Makefile dependencies ]
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
[fixup] Makefile dep
And actually link to it from vhost-user-bridge.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Block driver documentation is available in qemu-doc.html. It would be
convenient to have documentation for formats, protocols, and filter
drivers in a man page.
Extract the relevant part of qemu-doc.html into a new file called
docs/qemu-block-drivers.texi. This file can also be built as a
stand-alone document (man, html, etc).
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Proper support of persistent reservation for multipath devices requires
communication with the multipath daemon, so that the reservation is
registered and applied when a path comes up. The device mapper
utilities provide a library to do so; this patch makes qemu-pr-helper.c
detect multipath devices and, when one is found, delegate the operation
to libmpathpersist.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Introduce a privileged helper to run persistent reservation commands.
This lets virtual machines send persistent reservations without using
CAP_SYS_RAWIO or out-of-tree patches. The helper uses Unix permissions
and SCM_RIGHTS to restrict access to processes that can access its socket
and prove that they have an open file descriptor for a raw SCSI device.
The next patch will also correct the usage of persistent reservations
with multipath devices.
It would also be possible to support for Linux's IOC_PR_* ioctls in
the future, to support NVMe devices. For now, however, only SCSI is
supported.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Using two libraries (libqemuutil.a and libqemustub.a) would sometimes
result in circular dependencies. To avoid these issues let's just
combine both into a single library that functions as both.
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Message-Id: <54e6458745493d10901964624479a7d9a872f481.1503077821.git.alistair.francis@xilinx.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Drop pixman submodule and support for the "internal" pixman build.
pixman should be reasonably well established meanwhile so we don't
need the fallback submodule any more. While being at it also drop
some #ifdefs for pixman versions older than what we require in
configure anyway.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20170905140116.28181-2-kraxel@redhat.com
Sadly, we don't have a TPM maintainer, not even a MAINTAINERS entry.
Create one, and mark it orphaned.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <1503602048-12268-12-git-send-email-armbru@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Cc: Juan Quintela <quintela@redhat.com>
Cc: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <1503602048-12268-10-git-send-email-armbru@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Cc: Jason Wang <jasowang@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <1503602048-12268-8-git-send-email-armbru@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
