Notice raise and bpt, decoding the constants embedded in the
nop addil instruction in the x0 slot.
[rth: Generalize TILEGX_EXCP_OPCODE_ILL to TILEGX_EXCP_SIGNAL.
Drop validation of signal values.]
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Message-Id: <1443243635-4886-1-git-send-email-gang.chen.5i5j@gmail.com>
Signed-off-by: Richard Henderson <rth@twiddle.net>
[rth: Remove the spreg[EX1] handling, as it's irrelevant to user-mode.]
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Message-Id: <1443312618-13641-1-git-send-email-gang.chen.5i5j@gmail.com>
Signed-off-by: Richard Henderson <rth@twiddle.net>
They content several new macro members, also contents TARGET_N*.
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Message-Id: <1443240605-2924-1-git-send-email-gang.chen.5i5j@gmail.com>
Signed-off-by: Richard Henderson <rth@twiddle.net>
According to the related document, bpt can be only in x1 pipe.
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Message-Id: <1443224574-2718-1-git-send-email-gang.chen.5i5j@gmail.com>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Message-Id: <1442874414-3578-1-git-send-email-gang.chen.5i5j@gmail.com>
Signed-off-by: Richard Henderson <rth@twiddle.net>
[rth: Implement everything inline; handle v1addi and v2addi as well.]
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Message-Id: <1442873918-3394-1-git-send-email-gang.chen.5i5j@gmail.com>
Signed-off-by: Richard Henderson <rth@twiddle.net>
v2sh* are implemented with helper functions; v4sh* are implmeneted
with inline code.
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Message-Id: <1442872055-2836-1-git-send-email-gang.chen.5i5j@gmail.com>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Using the V1 macro when we want to replicate a byte across
the 8 elements of the word. Using deposit and extract for
manipulating specific elements.
Signed-off-by: Richard Henderson <rth@twiddle.net>
pc_dimm_realize() validates the NUMA node to which memory hotplug is
being performed only in case of NUMA configuration. Include a check to
fail for invalid nodes in case of non-NUMA configuration too.
Signed-off-by: Bharata B Rao <bharata@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Some fixes all over the place:
- ccw bios and gcc 5.1 (avoid floating point ops)
- properly print vector registers
- sclp and sclp-event-facility no longer hang on object_unref(object_new(T))
- better name for io_subsystem_reset
One feature
- the gdb server now exposes several virtualization specific register
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.14 (GNU/Linux)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=STtO
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/borntraeger/tags/s390x-20151006' into staging
s390: fixes
Some fixes all over the place:
- ccw bios and gcc 5.1 (avoid floating point ops)
- properly print vector registers
- sclp and sclp-event-facility no longer hang on object_unref(object_new(T))
- better name for io_subsystem_reset
One feature
- the gdb server now exposes several virtualization specific register
# gpg: Signature made Tue 06 Oct 2015 11:20:24 BST using RSA key ID B5A61C7C
# gpg: Good signature from "Christian Borntraeger (IBM) <borntraeger@de.ibm.com>"
* remotes/borntraeger/tags/s390x-20151006:
s390x: rename io_subsystem_reset -> subsystem_reset
s390x/info registers: print vector registers properly
s390x: set missing parent for hotplug and quiesce events
s390x/gdb: expose virtualization specific registers
pc-bios/s390-ccw: avoid floating point operations
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=pr5r
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/ehabkost/tags/x86-pull-request' into staging
X86 queue, 2015-10-05
# gpg: Signature made Mon 05 Oct 2015 17:04:38 BST using RSA key ID 984DC5A6
# gpg: Good signature from "Eduardo Habkost <ehabkost@redhat.com>"
* remotes/ehabkost/tags/x86-pull-request:
icc_bus: drop the unused files
cpu/apic: drop icc bus/bridge
x86: use new method to correct reset sequence
apic: move APIC's MMIO region mapping into APIC
Correctly re-init EFER state during INIT IPI
target-i386: add ABM to Haswell* and Broadwell* CPU models
target-i386: get/put MSR_TSC_AUX across reset and migration
target-i386: Make check_hw_breakpoints static
target-i386: Move breakpoint related functions to new file
target-i386: Convert kvm_default_*features to property/value pairs
vl: Add another sanity check to smp_parse() function
cpu: Introduce X86CPUTopoInfo structure for argument simplification
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
vhost-user depends on vhost-net. We should probably fix that.
For now, let's disable the test otherwise.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
At present the memory listener used by vfio to keep host IOMMU mappings
in sync with the guest memory image assumes that if a guest IOMMU
appears, then it has no existing mappings.
This may not be true if a VFIO device is hotplugged onto a guest bus
which didn't previously include a VFIO device, and which has existing
guest IOMMU mappings.
Therefore, use the memory_region_register_iommu_notifier_replay()
function in order to fix this case, replaying existing guest IOMMU
mappings, bringing the host IOMMU into sync with the guest IOMMU.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
When we have guest visible IOMMUs, we allow notifiers to be registered
which will be informed of all changes to IOMMU mappings. This is used by
vfio to keep the host IOMMU mappings in sync with guest IOMMU mappings.
However, unlike with a memory region listener, an iommu notifier won't be
told about any mappings which already exist in the (guest) IOMMU at the
time it is registered. This can cause problems if hotplugging a VFIO
device onto a guest bus which had existing guest IOMMU mappings, but didn't
previously have an VFIO devices (and hence no host IOMMU mappings).
This adds a memory_region_iommu_replay() function to handle this case. It
replays any existing mappings in an IOMMU memory region to a specified
notifier. Because the IOMMU memory region doesn't internally remember the
granularity of the guest IOMMU it has a small hack where the caller must
specify a granularity at which to replay mappings.
If there are finer mappings in the guest IOMMU these will be reported in
the iotlb structures passed to the notifier which it must handle (probably
causing it to flag an error). This isn't new - the VFIO iommu notifier
must already handle notifications about guest IOMMU mappings too short
for it to represent in the host IOMMU.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Depending on the host IOMMU type we determine and record the available page
sizes for IOMMU translation. We'll need this for other validation in
future patches.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
The current vfio core code assumes that the host IOMMU is capable of
mapping any IOVA the guest wants to use to where we need. However, real
IOMMUs generally only support translating a certain range of IOVAs (the
"DMA window") not a full 64-bit address space.
The common x86 IOMMUs support a wide enough range that guests are very
unlikely to go beyond it in practice, however the IOMMU used on IBM Power
machines - in the default configuration - supports only a much more limited
IOVA range, usually 0..2GiB.
If the guest attempts to set up an IOVA range that the host IOMMU can't
map, qemu won't report an error until it actually attempts to map a bad
IOVA. If guest RAM is being mapped directly into the IOMMU (i.e. no guest
visible IOMMU) then this will show up very quickly. If there is a guest
visible IOMMU, however, the problem might not show up until much later when
the guest actually attempt to DMA with an IOVA the host can't handle.
This patch adds a test so that we will detect earlier if the guest is
attempting to use IOVA ranges that the host IOMMU won't be able to deal
with.
For now, we assume that "Type1" (x86) IOMMUs can support any IOVA, this is
incorrect, but no worse than what we have already. We can't do better for
now because the Type1 kernel interface doesn't tell us what IOVA range the
IOMMU actually supports.
For the Power "sPAPR TCE" IOMMU, however, we can retrieve the supported
IOVA range and validate guest IOVA ranges against it, and this patch does
so.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
If a DMA mapping operation fails in vfio_listener_region_add() it
checks to see if we've already completed initial setup of the
container. If so it reports an error so the setup code can fail
gracefully, otherwise throws a hw_error().
There are other potential failure cases in vfio_listener_region_add()
which could benefit from the same logic, so move it to its own
fail: block. Later patches can use this to extend other failure cases
to fail as gracefully as possible under the circumstances.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Currently the VFIOContainer iommu_data field contains a union with
different information for different host iommu types. However:
* It only actually contains information for the x86-like "Type1" iommu
* Because we have a common listener the Type1 fields are actually used
on all IOMMU types, including the SPAPR TCE type as well
In fact we now have a general structure for the listener which is unlikely
to ever need per-iommu-type information, so this patch removes the union.
In a similar way we can unify the setup of the vfio memory listener in
vfio_connect_container() that is currently split across a switch on iommu
type, but is effectively the same in both cases.
The iommu_data.release pointer was only needed as a cleanup function
which would handle potentially different data in the union. With the
union gone, it too can be removed.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
In irqfd mode, current code attempts to set a resamplefd whatever
the type of the IRQ. For an edge-sensitive IRQ this attempt fails
and as a consequence, the whole irqfd setup fails and we fall back
to the slow mode. This patch bypasses the resamplefd setting for
non level-sentive IRQs.
Signed-off-by: Eric Auger <eric.auger@linaro.org>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
unmask EventNotifier might not be initialized in case of edge
sensitive irq. Using EventNotifier pointers make life simpler to
handle the edge-sensitive irqfd setup.
Signed-off-by: Eric Auger <eric.auger@linaro.org>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
With current implementation, eventfd VFIO signaling is first set up and
then irqfd is setup, if supported and allowed.
This start sequence causes several issues with IRQ forwarding setup
which, if supported, is transparently attempted on irqfd setup:
IRQ forwarding setup is likely to fail if the IRQ is detected as under
injection into the guest (active at irqchip level or VFIO masked).
This currently always happens because the current sequence explicitly
VFIO-masks the IRQ before setting irqfd.
Even if that masking were removed, we couldn't prevent the case where
the IRQ is under injection into the guest.
So the simpler solution is to remove this 2-step startup and directly
attempt irqfd setup. This is what this patch does.
Also in case the eventfd setup fails, there is no reason to go farther:
let's abort.
Signed-off-by: Eric Auger <eric.auger@linaro.org>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
libqos/ahci and tests/fdc-test are under my purview also,
include them in the appropriate stanzas.
Signed-off-by: John Snow <jsnow@redhat.com>
Message-id: 1443117055-29240-1-git-send-email-jsnow@redhat.com
ICC bus impl has been droped, so all icc related files are not useful
any more; delete them.
Signed-off-by: Zhu Guihua <zhugh.fnst@cn.fujitsu.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
After CPU hotplug has been converted to BUS-less hot-plug infrastructure,
the only function ICC bus performs is to propagate reset to LAPICs. However
LAPIC could be reset by registering its reset handler after all device are
initialized.
Do so and drop ~30LOC of not needed anymore ICCBus related code.
Signed-off-by: Chen Fan <chen.fan.fnst@cn.fujitsu.com>
Signed-off-by: Zhu Guihua <zhugh.fnst@cn.fujitsu.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
During reset some devices (such as hpet, rtc) might send IRQ to APIC
which changes APIC's state from default one it's supposed to have
at machine startup time.
Fix this by resetting APIC after devices have been reset to cancel
any changes that qemu_devices_reset() might have done to its state.
Signed-off-by: Zhu Guihua <zhugh.fnst@cn.fujitsu.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
When ICC bus/bridge is removed, APIC MMIO will be left
unmapped since it was mapped into system's address space
indirectly by ICC bridge.
Fix it by moving mapping into APIC code, so it would be
possible to remove ICC bus/bridge code later.
Signed-off-by: Chen Fan <chen.fan.fnst@cn.fujitsu.com>
Signed-off-by: Zhu Guihua <zhugh.fnst@cn.fujitsu.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
When doing a re-initialization of a CPU core, the default state is to _not_
have 64-bit long mode enabled. This means the LME (long mode enable) and LMA
(long mode active) bits in the EFER model-specific register should be cleared.
However, the EFER state is part of the CPU environment which is
preserved by do_cpu_init(), so if EFER.LME and EFER.LMA were set at the
time an INIT IPI was received, they will remain set after the init completes.
This is contrary to what the Intel architecture manual describes and what
happens on real hardware, and it leaves the CPU in a weird state that the
guest can't clear.
To fix this, the 'efer' member of the CPUX86State structure has been moved
to an area outside the region preserved by do_cpu_init(), so that it can
be properly re-initialized by x86_cpu_reset().
Signed-off-by: Bill Paul <wpaul@windriver.com>
CC: Paolo Bonzini <pbonzini@redhat.com>
CC: Richard Henderson <rth@twiddle.net>
CC: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
ABM is only implemented as a single instruction set by AMD; all AMD
processors support both instructions or neither. Intel considers POPCNT
as part of SSE4.2, and LZCNT as part of BMI1, but Intel also uses AMD's
ABM flag to indicate support for both POPCNT and LZCNT. It has to be
added to Haswell and Broadwell because Haswell, by adding LZCNT, has
completed the ABM.
Tested with "qemu-kvm -cpu Haswell-noTSX,enforce" (and also with older
machine types) on an Haswell-EP machine.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
There's one report of migration breaking due to missing MSR_TSC_AUX
save/restore. Fix this by adding a new subsection that saves the state
of this MSR.
https://bugzilla.redhat.com/show_bug.cgi?id=1261797
Reported-by: Xiaoqing Wei <xwei@redhat.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
CC: Paolo Bonzini <pbonzini@redhat.com>
CC: Juan Quintela <quintela@redhat.com>
CC: "Dr. David Alan Gilbert" <dgilbert@redhat.com>
CC: Marcelo Tosatti <mtosatti@redhat.com>
CC: Richard Henderson <rth@twiddle.net>
CC: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
The function is now only used from within a single file.
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Convert the kvm_default_features and kvm_default_unset_features arrays
into a simple list of property/value pairs that will be applied to
X86CPU objects when using KVM.
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
The code in smp_parse already checks the topology information for
sockets * cores * threads < cpus and bails out with an error in
that case. However, it is still possible to supply a bad configuration
the other way round, e.g. with:
qemu-system-xxx -smp 4,sockets=1,cores=4,threads=2
QEMU then still starts the guest, with topology configuration that
is rather incomprehensible and likely not what the user wanted.
So let's add another check to refuse such wrong configurations.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Acked-by: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
In order to simplify arguments of function, introduce a new struct
named X86CPUTopoInfo.
Signed-off-by: Chen Fan <chen.fan.fnst@cn.fujitsu.com>
Signed-off-by: Zhu Guihua <zhugh.fnst@cn.fujitsu.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
New features:
guest RAM buffer overrun mitigation
RAM physical address gaps for memory hotplug
(except refactoring which got some review comments)
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWDo8IAAoJECgfDbjSjVRpCwgH/jmj2sYXmP2ywGxsHOS7JKEF
DyF9crBbrNnkB0+qpON0vmCeoFx5AX6CeyWC0w2bFy4z2yN9lb7jKenkp/guHWne
eX4x5RVpvW9Ed1l9v4vGuI+5IB3gvZEXQB4hiAMz5fXMCVs0OZ4dyRODHqyXKMvy
lBCdb0YVvZOPYxRYhnAllOt0uBLLY8pl5i6QGekFkfQMCrsLagySqLPkRNTR0l8O
2PNd3oBPJi5Qb2jWyJNS45mPMDU6lEIiZSbzn7zAUVduu15hqS9VYZPlZzrNazSu
7hx6Zegq0G1MMpiVhwlpi5Ov1hqAA+zAIl4QcTN31ueHYdxD/x310nAqtm7Eov4=
=iFA1
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
virtio,pc features, fixes
New features:
guest RAM buffer overrun mitigation
RAM physical address gaps for memory hotplug
(except refactoring which got some review comments)
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Fri 02 Oct 2015 15:04:56 BST using RSA key ID D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>"
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>"
* remotes/mst/tags/for_upstream:
vhost-user-test: fix predictable filename on tmpfs
vhost-user-test: use tmpfs by default
pc: memhp: force gaps between DIMM's GPA
memhp: extend address auto assignment to support gaps
vhost-user: unit test for new messages
vhost-user-test: do not reinvent glib-compat.h
virtio: Notice when the system doesn't support MSIx at all
pc: Add a comment explaining why pc_compat_2_4() doesn't exist
exec: allocate PROT_NONE pages on top of RAM
oslib: allocate PROT_NONE pages on top of RAM
oslib: rework anonimous RAM allocation
virtio-net: correctly drop truncated packets
virtio: introduce virtqueue_discard()
virtio: introduce virtqueue_unmap_sg()
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=89TV
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/riku/tags/pull-linux-user-20151002' into staging
First set of Linux-user que patches for 2.5
# gpg: Signature made Fri 02 Oct 2015 13:38:00 BST using RSA key ID DE3C9BC0
# gpg: Good signature from "Riku Voipio <riku.voipio@iki.fi>"
# gpg: aka "Riku Voipio <riku.voipio@linaro.org>"
* remotes/riku/tags/pull-linux-user-20151002:
linux-user: assert that target_mprotect cannot fail
linux-user/signal.c: Use setup_rt_frame() instead of setup_frame() for target openrisc
linux-user/syscall.c: Add EAGAIN to host_to_target_errno_table for
linux-user: add name_to_handle_at/open_by_handle_at
linux-user: Return target error number in do_fork()
linux-user: fix cmsg conversion in case of multiple headers
linux-user: remove MAX_ARG_PAGES limit
linux-user: remove unused image_info members
linux-user: Treat --foo options the same as -foo
linux-user: use EXIT_SUCCESS and EXIT_FAILURE
linux-user: Add proper error messages for bad options
linux-user: Add -help
linux-user: Exit 0 when -h is used
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
vhost-user-test uses getpid to create a unique filename. This name is
predictable, and a security problem. Instead, use a tmp directory
created by mkdtemp, which is a suggested best practice.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Most people don't run make check by default, so they skip vhost-user
unit tests. Solve this by using tmpfs instead, unless hugetlbfs is
specified (using an environment variable).
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
mapping DIMMs non contiguously allows to workaround
virtio bug reported earlier:
http://lists.nongnu.org/archive/html/qemu-devel/2015-08/msg00522.html
in this case guest kernel doesn't allocate buffers
that can cross DIMM boundary keeping each buffer
local to a DIMM.
Suggested-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
setting gap to TRUE will make sparse DIMM
address auto allocation, leaving gaps between
a new DIMM address and preceeding existing DIMM.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Data is empty for now, but do make sure master
sets the new feature bit flag.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
glib-compat.h has the gunk to support both old-style and new-style
gthread functions. Use it instead of reinventing it.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Tested-by: Marc-André Lureau <marcandre.lureau@redhat.com>
