The value of the MVFR1 (Media and VFP Feature Register 1) register for
the Cortex-A8 appears to be incorrect (according to the TRM, DDI0344K),
with the "full denormal arithmetic" and "propagation of NaN" fields
holding both 0 instead of both 1.
I had a go tracing the history of the use of this value, and it seems
it's always just been wrong in QEMU: maybe it was derived from early
documentation, or guessed based on the use of a "VFP Lite" implementation
in the Cortex-A8.
Depending on the startup/early-boot code in use, this can manifest as
failure to perform denormal arithmetic properly: in our case, selecting
a Cortex-A8 CPU when using QEMU as an instruction-set simulator for
bare-metal GCC testing caused tests using denormal arithmetic to
fail. Problems might be masked (or not occur) when using a full OS kernel
with suitable trap handlers (I'm not sure).
Signed-off-by: Julian Brown <julian@codesourcery.com>
Message-id: 1481130858-31767-1-git-send-email-julian@codesourcery.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When register Rcvr_timeout_reg0 (R_RTOR in cadence_uart.c) is set to
0, the receiver timeout counter should be disabled. See page 1801 of
"Zynq-7000 AP SoC Technical Reference Manual". This commit adds a
such a check before setting the receive timeout interrupt.
Signed-off-by: Andrew Gacek <andrew.gacek@gmail.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Cadence UART device emulator calculates speed by dividing the
baud rate by a 'baud rate generator' & 'baud rate divider' value.
The device specification defines these register values to be
non-zero and within certain limits. Checks were recently added when
writing to these registers but not when restoring from migration.
This patch adds checks when restoring from migration to avoid divide by
zero errors.
Reported-by: Huawei PSIRT <psirt@huawei.com>
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 04ae30ed8ee1758cd2d2af880da4d28f74c67738.1481132150.git.alistair.francis@xilinx.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch add 3des-ede support for cryptodev. However this is effective
only when backend using libgcrypt/nettle, because cipher-builtin doesn't
support 3des-ede yet.
Signed-off-by: Longpeng(Mike) <longpeng2@huawei.com>
Signed-off-by: Gonglei <arei.gonglei@huawei.com>
Single-DES is obsolete and it's broken/useless for decades, we should
remove it in cryptodev, as suggested by Daniel.
Guest who wants to use this obsolete cipher alg will use its built-in
implementation instead.
Signed-off-by: Longpeng(Mike) <longpeng2@huawei.com>
Reviewed-by: Daniel P. Berrange <berrange@redhat.com>
Signed-off-by: Gonglei <arei.gonglei@huawei.com>
As the key length of xts(aes) is different with other mode of aes,
so we should check specially in cryptodev_builtin_get_aes_algo, if
it is xts mode.
Signed-off-by: Longpeng(Mike) <longpeng2@huawei.com>
Reviewed-by: Gonglei <arei.gonglei@huawei.com>
Signed-off-by: Gonglei <arei.gonglei@huawei.com>
We can't use LOAD AND TEST for unsigned data and then expect to
extract the result with ADD LOGICAL WITH CARRY. Fall through to
using COMPARE LOGICAL IMMEDIATE instead.
Signed-off-by: Richard Henderson <rth@twiddle.net>
* rules.mak speedup and cleanups from myself and Marc-Adnré
* multiboot command line fix from Vlad
* SCSI fixes from myself
* small qemu-timer speedup from myself
* x86 debugging improvements from Doug
* configurable Q35 devices from Chao
* x86 5-level paging support from Kirill
* x86 SHA_NI support for KVM from Yi Sun
* improved kvmclock migration logic from Marcelo
* bugfixes and doc fixes from others
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQExBAABCAAbBQJYW+q5FBxwYm9uemluaUByZWRoYXQuY29tAAoJEL/70l94x66D
H7cH/i5SpYY96aMGqK/QOIL9GfLPOeNayUFyf4Mnt/9B/85l9vAIf8uVARDpO7Mw
AiVZcdIj/PAFJ5jrLWA8qvBBaWS69Cfq1/hQfsWWlG3FcXU1Lzc/I76d8pAZC+9P
BZ/YWX3ZO6aOcT7XqzsBINoofyyjwUFNeYaoWwrUsWJVFG3987cbIMmnNp9pqxhZ
4pcMpycnWQJULP+P+AT6YjJaX7G017bXlrsc+iDh1dBe3Ah/Lp0Wy73YahAI5Dq2
3MT8bECjSIRQuT5xCyAsfN3latUVoAZrkJH3dApqg5RbqKWIkdpfQ0gIbGX8l3P5
DU5NRQcTujCPl8VdsNnrr796HV0=
=VhCX
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/bonzini/tags/for-upstream' into staging
* core support for MemoryRegionCache from myself
* rules.mak speedup and cleanups from myself and Marc-Adnré
* multiboot command line fix from Vlad
* SCSI fixes from myself
* small qemu-timer speedup from myself
* x86 debugging improvements from Doug
* configurable Q35 devices from Chao
* x86 5-level paging support from Kirill
* x86 SHA_NI support for KVM from Yi Sun
* improved kvmclock migration logic from Marcelo
* bugfixes and doc fixes from others
# gpg: Signature made Thu 22 Dec 2016 15:01:13 GMT
# gpg: using RSA key 0xBFFBD25F78C7AE83
# gpg: Good signature from "Paolo Bonzini <bonzini@gnu.org>"
# gpg: aka "Paolo Bonzini <pbonzini@redhat.com>"
# Primary key fingerprint: 46F5 9FBD 57D6 12E7 BFD4 E2F7 7E15 100C CD36 69B1
# Subkey fingerprint: F133 3857 4B66 2389 866C 7682 BFFB D25F 78C7 AE83
* remotes/bonzini/tags/for-upstream: (25 commits)
x86: implement la57 paging mode
target-i386: Fix eflags.TF/#DB handling of syscall/sysret insns
kvmclock: reduce kvmclock difference on migration
kvm: sync linux headers
scsi-disk: fix VERIFY for scsi-block
hw/block/pflash_cfi*.c: fix confusing assert fail message
multiboot: copy the cmdline verbatim, unescape module strings
x86: Fix x86_64 'g' packet response to gdb from 32-bit mode.
pc: make pit configurable
pc: make sata configurable
pc: make smbus configurable
target-i386: Add Intel SHA_NI instruction support.
block: drop remaining legacy aio functions in comment
main-loop: update comment for qemu_mutex_lock/unlock_iothread
timer: fix misleading comment in timer.h
qemu-timer: check active_timers outside lock/event
virtio-scsi: introduce virtio_scsi_acquire/release
build-sys: remove libtool left-over
rules.mak: add more rules to avoid chaining
rules.mak: speedup save-vars load-vars
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The new paging more is extension of IA32e mode with more additional page
table level.
It brings support of 57-bit vitrual address space (128PB) and 52-bit
physical address space (4PB).
The structure of new page table level is identical to pml4.
The feature is enumerated with CPUID.(EAX=07H, ECX=0):ECX[bit 16].
CR4.LA57[bit 12] need to be set when pageing enables to activate 5-level
paging mode.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Message-Id: <20161215001305.146807-1-kirill.shutemov@linux.intel.com>
[Drop changes to target-i386/translate.c. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The syscall and sysret instructions behave a bit differently:
TF is checked after the instruction completes.
This allows the o/s to disable #DB at a syscall by adding TF to FMASK.
And then when the sysret is executed the #DB is taken "as if" the
syscall insn just completed.
Signed-off-by: Doug Evans <dje@google.com>
Message-Id: <94eb2c0bfa1c6a9fec0543057483@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Check for KVM_CAP_ADJUST_CLOCK capability KVM_CLOCK_TSC_STABLE, which
indicates that KVM_GET_CLOCK returns a value as seen by the guest at
that moment.
For new machine types, use this value rather than reading
from guest memory.
This reduces kvmclock difference on migration from 5s to 0.1s
(when max_downtime == 5s).
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Message-Id: <20161121105052.598267440@redhat.com>
[Add comment explaining what is going on. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When a scsi-disk object receives VERIFY command with BYTCHK bit being zero,
scsi_block_is_passthrough returns false and finally makes req being proceeded
by scsi_block_dma_command. Because scsi_block_dma_command has removed process
of VERIFY, QEMU will abort in this function.
Reported-by: Junlian Bell <zhongjun@sangfor.com.cn>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The patch is to fix the confusing assert fail message caused by
un-initialized device structure (from bite sized tasks).
The bug can be reproduced by
./qemu-system-x86_64 -nographic -device cfi.pflash01
The CFI hardware is dynamically loaded by QOM realizing mechanism,
however the realizing function in pflash_cfi01_realize function
requires the device being initialized manually before calling, like
./qemu-system-x86_64 -nographic
-device cfi.pflash01,num-blocks=1024,sector-length=4096,name=testcard
Once the initializing parameters are left off in the command, it will
leave the device structure not initialized, which makes
pflash_cfi01_realize try to realize a zero-volume card, causing
/mnt/EXT_volume/projects/qemu/qemu-dev/exec.c:1378:
find_ram_offset: Assertion `size != 0\' failed.
Through my test, at least the flash device's block-number, sector-length
and its name is needed for pflash_cfi01_realize to behave correctly. So
I think the new asserts are needed to hint the QEMU user to specify
the device's parameters correctly.
Signed-off-by: Ziyue Yang <skiver.cloud.yzy@gmail.com>
Message-Id: <1481810693-13733-1-git-send-email-skiver.cloud.yzy@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Ziyue Yang <yzylivezh@hotmail.com>
get_opt_value() truncates the value at the first comma
Use memcpy() instead so that -append works correctly in the
presence of commas. For -initrd to work right, instead,
unescape the module filename and parameters with get_opt_value()
before calling mb_add_cmdline().
Signed-off-by: Vlad Lungu <vlad.lungu@windriver.com>
Message-Id: <1481805124-16242-1-git-send-email-vlad.lungu@windriver.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The remote protocol can't handle flipping back and forth
between 32-bit and 64-bit regs. To compensate, pretend "as if"
on 64-bit cpu when in 32-bit mode.
Signed-off-by: Doug Evans <dje@google.com>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Message-Id: <001a113dca8274572005406e03c3@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Commit 87f68d3182 (block: drop aio
functions that operate on the main AioContext) drops qemu_aio_wait
function references mostly while leaves these behind, clean up them.
Signed-off-by: Yaowei Bai <baiyaowei@cmss.chinamobile.com>
Message-Id: <1480566640-27264-3-git-send-email-baiyaowei@cmss.chinamobile.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Commit 49cf57281b (vl: delay thread initialization after daemonization)
makes the global mutex is taken after daemonization instead before
daemonization by qemu_init_main_loop().
Signed-off-by: Yaowei Bai <baiyaowei@cmss.chinamobile.com>
Message-Id: <1480566640-27264-2-git-send-email-baiyaowei@cmss.chinamobile.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
It's timer to expire, not clock.
Signed-off-by: Yaowei Bai <baiyaowei@cmss.chinamobile.com>
Message-Id: <1480566640-27264-1-git-send-email-baiyaowei@cmss.chinamobile.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This avoids taking the active_timers_lock or resetting/setting the
timers_done_ev if there are no active timers. This removes a small
(2-3%) source of overhead for dataplane. The list is then checked
again inside the lock, or a NULL pointer could be dereferenced.
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
These will be used more as soon as the acquire/release is pushed down to
the ioeventfd handlers.
Reviewed-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Libtool support was removed in commit e999ee4434, there is a few
left-over.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20161108070513.30274-1-marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Really rule chaining is not a particularly expensive task, since
GNU Make caches the directory listing. However it is easy to
avoid it for most files and for phony targets (one was missing).
After this patch, only "Makefile", "scripts/hxtool" and
"scripts/create_config" attempt to use chained rules.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Unnesting variables spends a lot of time parsing and executing foreach
and if functions. Because actually very few variables have to be
saved and restored, a good strategy is to remember what has to be done
in load-vars, and only iterate the right variables in load-vars.
For save-vars, unroll the foreach loop to provide another small
improvement.
This speeds up a "noop" build from around 15.5 seconds on my laptop
to 11.7 (25% roughly).
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When the Intel 6300ESB watchdog is hot unplug. The timer allocated
in realize isn't freed thus leaking memory leak. This patch avoid
this through adding the exit function.
Signed-off-by: Li Qiang <liqiang6-s@360.cn>
Message-Id: <583cde9c.3223ed0a.7f0c2.886e@mx.google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Device models often have to perform multiple access to a single
memory region that is known in advance, but would to use "DMA-style"
functions instead of address_space_map/unmap. This can happen
for example when the data has to undergo endianness conversion.
Introduce a new data structure to cache the result of
address_space_translate without forcing usage of a host address
like address_space_map does.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This extracts the common part of address_space_map and
address_space_cache_init into a new function.
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Templatize the address_space_* and *_phys functions, so that we can add
similar functions in the next patch that work with a lightweight,
cache-like version of address_space_map/unmap.
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Do them right before the next patch generalizes them into a multi-included
file.
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch add nettle-backed HMAC algorithms support
Signed-off-by: Longpeng(Mike) <longpeng2@huawei.com>
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
This patch add glib-backed HMAC algorithms support
Signed-off-by: Longpeng(Mike) <longpeng2@huawei.com>
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
This patch add HMAC algorithms based on libgcrypt support
Signed-off-by: Longpeng(Mike) <longpeng2@huawei.com>
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
This patch introduce HMAC algorithms framework.
Signed-off-by: Longpeng(Mike) <longpeng2@huawei.com>
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
This item will be used for support libcrypt-backed HMAC algorithms.
Support for hmac has been added in Libgcrypt 1.6.0, but we cannot
use pkg-config to get libcrypt's version. However we can make a
in configure to know whether current libcrypt support hmac.
Signed-off-by: Longpeng(Mike) <longpeng2@huawei.com>
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Libgcrypt and nettle support 3des-ede, so this patch add 3des-ede
support when using libgcrypt or nettle.
Reviewed-by: Gonglei <arei.gonglei@huawei.com>
Signed-off-by: Longpeng(Mike) <longpeng2@huawei.com>
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
On error path, ctx may be leaked. Assign ctx earlier, and call
qcrypto_cipher_free() on error.
Spotted thanks to ASAN.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
The blocksize option is defined in RFC 1783 and RFC 2348.
We now support block sizes between 1 and 1428 bytes, instead of 512 only.
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
We've currently got 18 architectures in QEMU, and thus 18 target-xxx
folders in the root folder of the QEMU source tree. More architectures
(e.g. RISC-V, AVR) are likely to be included soon, too, so the main
folder of the QEMU sources slowly gets quite overcrowded with the
target-xxx folders.
To disburden the main folder a little bit, let's move the target-xxx
folders into a dedicated target/ folder, so that target-xxx/ simply
becomes target/xxx/ instead.
Acked-by: Laurent Vivier <laurent@vivier.eu> [m68k part]
Acked-by: Bastian Koppelmann <kbastian@mail.uni-paderborn.de> [tricore part]
Acked-by: Michael Walle <michael@walle.cc> [lm32 part]
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com> [s390x part]
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com> [s390x part]
Acked-by: Eduardo Habkost <ehabkost@redhat.com> [i386 part]
Acked-by: Artyom Tarasenko <atar4qemu@gmail.com> [sparc part]
Acked-by: Richard Henderson <rth@twiddle.net> [alpha part]
Acked-by: Max Filippov <jcmvbkbc@gmail.com> [xtensa part]
Reviewed-by: David Gibson <david@gibson.dropbear.id.au> [ppc part]
Acked-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com> [crisµblaze part]
Acked-by: Guan Xuetao <gxt@mprc.pku.edu.cn> [unicore32 part]
Signed-off-by: Thomas Huth <thuth@redhat.com>