I've found that FreeBSD AHCI driver doesn't work with AHCI hardware
emulation of QEMU 0.15.0. I believe the problem is on QEMU's side. As I
see, it clears port's Interrupt Enable register each time when reset of
any level happens. Is is reasonable for the global controller reset. It
is probably not good, but acceptable for FreeBSD driver for the port
hard reset. But it is IMO wrong for the device soft reset. None of real
hardware I know behaves that way.
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
It will not be needed for reads and writes if the HBA provides a sglist.
In addition, this lets scsi-disk refuse commands with an excessive
allocation length, as well as limit memory on usual well-behaved guests.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Also, consistently use qiov.size instead of iov.iov_len.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
I found no rationale for this in the logs, and it is quite bad because
it will make scsi-generic unsafe WRT power failures.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Since we use memory API in sun4u.c, after
71579cae30, setting up isa_mem_base
puts vga.chain4 outside of the physical address space.
Fix by removing obsolete isa_mem_base set up.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
The virtio device lifecycle can be observed by looking at the sequence
of set status operations. This is especially important for catching the
reset operation (status value 0), which resets the device and all
virtqueues.
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Make qdev_device_help print both device and bus properties.
Helps libvirt to figure whenever bus properties such as
PCI.multifunction are supported present or not.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This does not yet unbreak PPC (which has its own problems) but
potentially other non-x86 systems where isa_mem_base is != 0.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Fix a number of bugs in the implementation of writes to the CM_CTRL
system register:
* write to cm_ctrl, not cm_init !
* an '&' vs '^' typo meant we would write the inverse of the bits
* handling the LED via printf() meant we spew lots of output
to stdout when Linux uses the LED as a heartbeat indicator
* we would hw_error() if a reset was requested rather than
actually resetting
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
In text mode, even a full refresh of the screen takes multiple updates.
As we reset the dump file pointer after the first call, we only wrote
the first line.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Those blanks violate the coding conventions, see
scripts/checkpatch.pl.
Blanks missing after colons in the changed lines were added.
This patch does not try to fix tabs, long lines and other
problems in the changed lines, therefore checkpatch.pl reports
many violations.
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Member variable is_read is written, but never read
(contrary to its name). Remove it.
Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
change fails while the tray is locked by the guest. eject -f forces
it open and removes any media. Unfortunately, the tray closes again
instantly. Since the lock remains as it is, there is no way to insert
another medium unless the guest voluntarily unlocks.
Fix by leaving the tray open after monitor eject.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
To let device models distinguish between eject and load.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Device models should be able to set it without an unclean include of
block_int.h.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Including it in device models is unclean, including it without a
reason adds insult to injury.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
It's convenience stuff for block device models, so block.h isn't the
ideal home either, but better than block_int.h.
Permits moving some #include "block_int.h" from device model .h into
.c.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Need to ask the device, so this requires new BlockDevOps member
is_tray_open().
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
It's a confused mess (see previous commit). No users remain.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
BlockDriverState member removable is a confused mess. It is true when
an ide-cd, scsi-cd or floppy qdev is attached, or when the
BlockDriverState was created with -drive if={floppy,sd} or -drive
if={ide,scsi,xen,none},media=cdrom ("created removable"), except when
an ide-hd, scsi-hd, scsi-generic or virtio-blk qdev is attached.
Three users remain:
1. eject_device(), via bdrv_is_removable() uses it to determine
whether a block device can eject media.
2. bdrv_info() is monitor command "info block". QMP documentation
says "true if the device is removable, false otherwise". From the
monitor user's point of view, the only sensible interpretation of
"is removable" is "can eject media with monitor commands eject and
change".
A block device can eject media unless a device is attached that
doesn't support it. Switch the two users over to new
bdrv_dev_has_removable_media() that returns exactly that.
3. bdrv_getlength() uses to suppress its length cache when media can
change (see commit 46a4e4e6). Media change is either monitor
command change (updates the length cache), monitor command eject
(doesn't update the length cache, easily fixable), or physical
media change (invalidates length cache, not so easily fixable).
I'm refraining from improving anything here, because this series is
long enough already. Instead, I simply switch it over to
bdrv_dev_has_removable_media() as well.
This changes the behavior of the length cache and of monitor commands
eject and change in two cases:
a. drive not created removable, no device attached
The commit makes the drive removable, and defeats the length cache.
Example: -drive if=none
b. drive created removable, but the attached drive is non-removable,
and doesn't call bdrv_set_removable(..., 0) (most devices don't)
The commit makes the drive non-removable, and enables the length
cache.
Example: -drive if=xen,media=cdrom -M xenpv
The other non-removable devices that don't call
bdrv_set_removable() can't currently use a drive created removable,
either because they aren't qdevified, or because they lack a drive
property. Won't stay that way.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Use a subsection, so that migration to older version still works,
provided the tray is closed and unlocked.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
MMC-5 6.40.2.6 specifies that START STOP UNIT succeeds when the drive
already has the requested state. cmd_start_stop_unit() fails when
asked to eject while the tray is open and locked. Fix that.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Requires new BlockDevOps member is_medium_locked(). Implement for IDE
and SCSI CD-ROMs.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The device model knows best when to accept the guest's eject command.
No need to detour through the block layer.
bdrv_eject() can't fail anymore. Make it void.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
We already track it in BlockDriverState. Just like tray open/close
state, we should track it in the device models instead, because it's
device state.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
We already track it in BlockDriverState. Just like tray open/close
state, we should track it in the device models instead, because it's
device state.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Commit 4be9762a changed bdrv_is_inserted() to fail when the tray is
open. Unfortunately, there are two different kinds of users, with
conflicting needs.
1. Device models using bdrv_eject(), currently ide-cd and scsi-cd.
They expect bdrv_is_inserted() to reflect the tray status. Commit
4be9762a makes them happy.
2. Code that wants to know whether a BlockDriverState has media, such
as find_image_format(), bdrv_flush_all(). Commit 4be9762a makes them
unhappy. In particular, it breaks flush on VM stop for media ejected
by the guest.
Revert the change to bdrv_is_inserted(). Check the tray status in the
device models instead.
Note on IDE: Since only ATAPI devices have a tray, and they don't
accept ATA commands since the recent commit "ide: Reject ATA commands
specific to drive kinds", checking in atapi.c suffices.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
We already track it in BlockDriverState since commit 4be9762a. As
discussed in that commit's message, we should track it in the device
device models instead, because it's device state.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
We already track it in BlockDriverState since commit 4be9762a. As
discussed in that commit's message, we should track it in the device
device models instead, because it's device state.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
"eject" is misleading; it means "eject" when start is clear, but
"load" when start is set. Rename to loej, because that's how MMC-5
calls it, in section 6.40.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
ACS-2 Table B.2 explicitly prohibits ATAPI devices from implementing
WIN_RECAL, WIN_READ_EXT, WIN_READDMA_EXT, WIN_READ_NATIVE_MAX,
WIN_MULTREAD_EXT, WIN_WRITE, WIN_WRITE_ONCE, WIN_WRITE_EXT,
WIN_WRITEDMA_EXT, WIN_MULTWRITE_EXT, WIN_WRITE_VERIFY, WIN_VERIFY,
WIN_VERIFY_ONCE, WIN_VERIFY_EXT, WIN_SPECIFY, WIN_MULTREAD,
WIN_MULTWRITE, WIN_SETMULT, WIN_READDMA, WIN_READDMA_ONCE,
WIN_WRITEDMA, WIN_WRITEDMA_ONCE, WIN_FLUSH_CACHE_EXT. Restrict them
to IDE_HD and IDE_CFATA.
Same for CFA_WRITE_SECT_WO_ERASE, CFA_WRITE_MULTI_WO_ERASE. Restrict
them to IDE_CFATA, like the other CFA_ commands.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
No functional change.
It would be nice to have handler functions in the table, like commit
e1a064f9 did for ATAPI. Left for another day.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Must set the ATAPI device signature, see ATA4 8.27.5.2 Outputs for
PACKET Command feature set devices, and ACS-2 7.36.6 Outputs for
PACKET feature set devices.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
See ISA, 4.4.6 (interrupt option), 4.4.7 (high priority interrupt
option) and 4.4.8 (timer interrupt option) for details.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Sample board and sample CPU core are used for debug and may be used for
development of custom SoC emulators.
This board has two fixed size memory regions for DTCM and ITCM and
variable length SRAM region.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Move mipsnet_init() function to mipssim machine
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Avoid this warning from clang analyzer by deleting the variable:
/src/qemu/hw/lsi53c895a.c:895:5: warning: Value stored to 'id' is never read
id = (current_tag >> 8) & 0xf;
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
The code does not have any effect as is, fix it.
Spotted by clang analyzer:
/src/qemu/hw/hid.c:99:13: warning: Value stored to 'x1' is never read
x1 = 1;
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Compile g364fb in hwlib. Two compilations less for the full build.
Acked-by: Hervé Poussineau <hpoussin@reactos.org>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
