The v8 ARM ARM defines that unused spaces in the ID_AA64* system
register ranges are Reserved and must RAZ, rather than being UNDEF.
Implement this.
In particular, ARM v8.2 adds a new feature register ID_AA64MMFR2,
and newer versions of the Linux kernel will attempt to read this,
which causes them not to boot up on versions of QEMU missing this fix.
Since the encoding .opc0 = 3, .opc1 = 0, .crn = 0, .crm = 2, .opc2 = 6
is actually defined in ARMv8 (as ID_MMFR4), we give it an entry in
the ARMCPU struct so CPUs can override it, though since none do
this too will just RAZ.
Cc: qemu-stable@nongnu.org
Reported-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1455890863-11203-1-git-send-email-peter.maydell@linaro.org
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Tested-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Aaron Lindsay <alindsay@codeaurora.org>
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Tested-by: Nathan Rossi <nathan@nathanrossi.com>
Message-id: da0563119a9f56fd5fbdc26e7ed19a8a8457c5b9.1455060548.git.alistair.francis@xilinx.com
[PMM: Use 0 for PMCEID0 values for A15 and A57 since our PMU
does not currently implement any events.]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
If EL2 or EL3 is present on an AArch64 CPU, then exceptions can be
taken to an exception level which is running AArch32 (if only EL0
and EL1 are present then EL1 must be AArch64 and all exceptions are
taken to AArch64). To support this we need to have a single
implementation of the CPU do_interrupt() method which can handle both
32 and 64 bit exception entry.
Pull the common parts of aarch64_cpu_do_interrupt() and
arm_cpu_do_interrupt() out into a new function which calls
either the AArch32 or AArch64 specific entry code once it has
worked out which one is needed.
We temporarily special-case the handling of EXCP_SEMIHOST to
avoid an assertion in arm_el_is_aa64(); the next patch will
pull all the semihosting handling out to the arm_cpu_do_interrupt()
level (since semihosting semantics depend on the register width
of the calling code, not on that of any higher EL).
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Move the aarch64_cpu_do_interrupt() function to helper.c. We want
to be able to call this from code that isn't AArch64-only, and
the move allows us to avoid awkward #ifdeffery at the callsite.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Implement cpu_get_phys_page_attrs_debug instead of cpu_get_phys_page_debug.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Add QOM property to the ARM CPU which boards can use to tell us what
memory region to use for secure accesses. Nonsecure accesses
go via the memory region specified with the base CPU class 'memory'
property.
By default, if no secure region is specified it is the same as the
nonsecure region, and if no nonsecure region is specified we will use
address_space_memory.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Add the support needed for creating prstatus elf notes. This
allows us to use QMP dump-guest-memory.
Signed-off-by: Andrew Jones <drjones@redhat.com>
Message-id: 1452542185-10914-6-git-send-email-drjones@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: moved setting of cpu::write_elf64_note inside !CONFIG_USER_ONLY
ifdef to avoid compile failure for linux-user build]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Introduces reusable definitions for CPU affinity masks/shifts and gets rid
of hardcoded magic numbers.
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Message-id: 7e6def4d0d91ae64615cdd2035b94d408d0a23c6.1441366248.git.p.fedin@samsung.com
[PMM: folded overlong line]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
On CPUs with EL3, there are two physical timers, one for Secure and one
for Non-secure. Implement this extra timer and the AArch64 registers
which access it.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 1437047249-2357-2-git-send-email-peter.maydell@linaro.org
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1436791864-4582-6-git-send-email-edgar.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Define the MPUIR register for MPU supporting ARMv6 and onwards.
Currently we only support unified MPU.
The size of the unified MPU is defined via the number of "dregions".
So just a single config is added to specify this size. (When split MPU
is implemented we will add an extra iregions config).
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Message-id: 9f248950b803a08c8b3c978931663182f7e882e7.1434501320.git.peter.crosthwaite@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
For processors that support MPUs, add a property to de-feature it. This
is similar to the implementation of the EL3 feature.
The processor definition in init sets ARM_FEATURE_MPU if it can support
an MPU. post_init exposes the property, defaulting to true. If cleared
by the instantiator, ARM_FEATURE_MPU is then removed at realize time.
This is to support R profile processors that may or may-not have an MPU
configured.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Message-id: 632918cc48786e868ea18aa6bd12f70597994cad.1434066412.git.peter.crosthwaite@xilinx.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add a boolean for indicating uniprocessors with MP extensions. This
drives the U bit in MPIDR. Prepares support for Cortex-R5.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Message-id: a70a80583df265e0174f01fa1fc92b33ea6d1db5.1434066412.git.peter.crosthwaite@xilinx.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When we're using KVM, the kernel's internal idea of the MPIDR
affinity fields must match the values we tell it for the guest
vcpu cluster configuration in the device tree. Since at the moment
the kernel doesn't support letting userspace tell it the correct
affinity fields to use, we must read the kernel's view and
reflect that back in the device tree.
Signed-off-by: Shlomo Pongratz <shlomo.pongratz@huawei.com>
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Message-id: 02f601d0a1e6$90c7d630$b2578290$@samsung.com
[PMM: Use a local #define rather than a global variable for
the TCG ARM_CPUS_PER_CLUSTER setting. Tweak a comment. Update the
commit message.]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
According to ARM Cortex-A53/A57 TRM, REVIDR reset value should be zero. So let
REVIDR reset value be specified by CPU model and correct it for Cortex-A53/A57.
Signed-off-by: Sergey Fedorov <serge.fdrv@gmail.com>
Message-id: 1433321048-23793-2-git-send-email-serge.fdrv@gmail.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Added a "has_el3" state property to the ARMCPU descriptor. This property
indicates whether the ARMCPU has security extensions enabled (EL3) or not.
By default it is disabled at this time.
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1418684992-8996-10-git-send-email-greg.bellows@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add support for handling PSCI calls in system emulation. Both version
0.1 and 0.2 of the PSCI spec are supported. Platforms can enable support
by setting the "psci-conduit" QOM property on the cpus to SMC or HVC
emulation and having a PSCI binding in their dtb.
Signed-off-by: Rob Herring <rob.herring@linaro.org>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1412865028-17725-7-git-send-email-peter.maydell@linaro.org
[PMM: made system reset/off PSCI functions power down the CPU so
we obey the PSCI API requirement never to return from them;
rearranged how the code is plumbed into the exception system,
so that we split "is this a valid call?" from "do the call"]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add tracking of cpu power state in order to support powering off of
cores in system emuluation. The initial state is determined by the
start-powered-off QOM property.
Signed-off-by: Rob Herring <rob.herring@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1412865028-17725-2-git-send-email-peter.maydell@linaro.org
Cc: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Message-id: 1410626734-3804-15-git-send-email-rth@twiddle.net
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Allow each CPU type to specify the value for the debug ID
registers, by putting them in the ARMCPU struct, and use
the resulting information to only expose the correct number
of watchpoint and breakpoint registers for the CPU.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Implement kvm_arm_vcpu_init() as a simple call to arm_arm_vcpu_init()
(which uses the KVM_ARM_VCPU_INIT vcpu ioctl to tell the kernel
to re-initialize the vCPU), rather than via the complicated code
which saves a copy of the register state on first init and then
writes it back to the kernel. This is much simpler and brings the
32-bit KVM code into line with the 64-bit code.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1403802973-20841-1-git-send-email-peter.maydell@linaro.org
We require to know the PSCI version available to given CPU at
potentially many places. Currently, we need to know PSCI version
when generating DTB for virt machine.
This patch introduce per-CPU 32bit field representing the PSCI
version available to the CPU. The encoding of this 32bit field
is same as described in PSCI v0.2 spec.
Signed-off-by: Pranavkumar Sawargaonkar <pranavkumar@linaro.org>
Signed-off-by: Anup Patel <anup.patel@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1402901605-24551-8-git-send-email-pranavkumar@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Introduce a common kvm_arm_vcpu_init() for doing KVM_ARM_VCPU_INIT
ioctl in KVM ARM and KVM ARM64. This also helps us factor-out few
common code lines from kvm_arch_init_vcpu() for KVM ARM/ARM64.
Signed-off-by: Pranavkumar Sawargaonkar <pranavkumar@linaro.org>
Signed-off-by: Anup Patel <anup.patel@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1402901605-24551-5-git-send-email-pranavkumar@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
For system mode, we may have a 64 bit CPU which is currently executing
in AArch32 state; if we're dumping CPU state to the logs we should
therefore show the correct state for the current execution state,
rather than hardwiring it based on the type of the CPU. For consistency
with how we handle translation, we leave the 32 bit dump function
as the default, and have it hand off control to the 64 bit dump code
if we're in AArch64 mode.
Reported-by: Rob Herring <rob.herring@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Cortex-A57, like most of the other ARM cores, has a CBAR
register which defines the base address of the per-CPU
peripherals. However it has a 64-bit view as well as a
32-bit view; expand the QOM reset-cbar property from UINT32
to UINT64 so this can be specified, and implement the
32-bit and 64-bit views of a 64-bit CBAR.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Implement the AArch64 RVBAR register, which indicates the reset
address. Since the reset address is implementation defined and
usually configurable by setting config signals in hardware, we
also provide a QOM property so it can be set at board level if
necessary.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
For ARMv8 there are two changes to the MVFR media feature registers:
* there is a new MVFR2 which is accessible from 32 bit code
* 64 bit code accesses these via the usual sysreg instructions
rather than with a floating-point specific instruction
Implement this.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Implement exception handling for AArch64 EL1. Exceptions from AArch64 or
AArch32 EL0 are supported.
Signed-off-by: Rob Herring <rob.herring@linaro.org>
[PMM: fixed minor style nits; updated to match changes in
previous patches; added some of the simpler cases of
illegal-exception-return support]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Implement the DC ZVA instruction, which clears a block of memory.
The fast path obtains a pointer to the underlying RAM via the TCG TLB
data structure so we can do a direct memset(), with fallback to a
simple byte-store loop in the slow path.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Acked-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Implement the AArch64-specific ID and feature registers. Although
many of these are currently not used by the architecture (and so
always zero for all implementations), we define the full set of
fields in the ARMCPU struct for symmetry.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Add an ARM CPU property for the reset value of hivecs as it is a
board/SoC configurable setting.
The existence of the property is conditional on the ARM CPU not being M
class.
Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Message-id: b04216c6bda4bd163f44a55bba552d0e8267481f.1387160489.git.peter.crosthwaite@xilinx.com
[ PC Changes:
* Elaborated commit message
* refactored to use qdev_property_add_static
]
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Instead of assuming that a KVM target CPU must always be a
Cortex-A15 and hardcoding this in kvm_arch_init_vcpu(),
store the KVM_ARM_TARGET_* value in the ARMCPU class,
and use that.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Message-id: 1385140638-10444-10-git-send-email-peter.maydell@linaro.org
New ARM boards are generally expected to boot their secondary CPUs
via the PSCI interface, rather than ad-hoc "loop around in holding
pen code" as hw/arm/boot.c implements. In particular this is
necessary for mach-virt kernels. For KVM we achieve this by creating
the VCPUs with a feature flag marking them as starting in PSCI
powered-down state; the guest kernel will then make a PSCI call
(implemented in the host kernel) to start the secondaries at
an address of its choosing once it has got the primary CPU up.
Implement this setting of the feature flag, controlled by a
qdev property for ARMCPU, which board code can set if it is a
PSCI system.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Message-id: 1385140638-10444-7-git-send-email-peter.maydell@linaro.org
Linux requires device tree CPU nodes to include a 'compatible'
string describing the CPU. Add a field in the ARMCPU struct for
this so that boards which construct a device tree can insert
the correct CPU nodes.
Note that there is currently no officially specified 'compatible'
string for the TI925T, Cortex-M3 or SA1110 CPUs.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Message-id: 1385140638-10444-6-git-send-email-peter.maydell@linaro.org
We want to be able to debug AArch64 guests. So let's add the respective gdb
stub functions and xml descriptions that allow us to do so.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: John Rigby <john.rigby@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1378235544-22290-12-git-send-email-peter.maydell@linaro.org
Message-id: 1368505980-17151-6-git-send-email-john.rigby@linaro.org
[PMM: dropped unused fp regs XML for now; moved 64 bit only functions
to new gdbstub64.c; these are hooked up in AArch64CPU, not via
ifdefs in ARMCPU]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We should translate AArch64 mode separately from AArch32 mode. In AArch64 mode,
registers look vastly different, instruction encoding is completely different,
basically the system turns into a different machine.
So let's do a simple if() in translate.c to decide whether we can handle the
current code in the legacy AArch32 code or in the new AArch64 code.
So far, the translation always complains about unallocated instructions. There
is no emulator functionality in this patch!
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: John Rigby <john.rigby@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1378235544-22290-11-git-send-email-peter.maydell@linaro.org
Message-id: 1368505980-17151-5-git-send-email-john.rigby@linaro.org
[PMM:
* provide no-op versions of a64 functions ifndef TARGET_AARCH64;
this lets us avoid #ifdefs in translate.c
* insert the missing call to disas_a64_insn()
* stash the insn in the DisasContext rather than reloading it in
real_unallocated_encoding()
]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Create a new AArch64CPU class; all 64-bit capable ARM
CPUs are subclasses of this. (Currently we only support
one, the "any" CPU used by linux-user.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1378235544-22290-8-git-send-email-peter.maydell@linaro.org
The ARMv7 architecture specifies a 'generic timer' which is implemented
via cp15 registers. Newer kernels will prefer to use this rather than
a devboard-level timer. Implement the generic timer for TCG; for KVM
we will already use the hardware's virtualized timer for this.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Laurent Desnogues <laurent.desnogues@gmail.com>
Message-id: 1376065080-26661-4-git-send-email-peter.maydell@linaro.org
Completes migration of target-specific code to new target-*/gdbstub.c.
Acked-by: Michael Walle <michael@walle.cc> (for lm32)
Acked-by: Max Filippov <jcmvbkbc@gmail.com> (for xtensa)
Signed-off-by: Andreas Färber <afaerber@suse.de>
Change breakpoint_invalidate() argument to CPUState alongside.
Since all targets now assign a softmmu-only field, we can drop helpers
cpu_class_set_{do_unassigned_access,vmsd}() and device_class_set_vmsd().
Prepares for changing cpu_memory_rw_debug() argument to CPUState.
Acked-by: Max Filippov <jcmvbkbc@gmail.com> (for xtensa)
Signed-off-by: Andreas Färber <afaerber@suse.de>
A transition from CPUFooState to FooCPU can be considered safe,
just like FooCPU::env access in the opposite direction.
The only benefit of the FOO_CPU() casts would be protection against
bogus CPUFooState pointers, but then surrounding code would likely
break, too.
This should slightly improve interrupt etc. performance when going from
CPUFooState to FooCPU.
For any additional CPU() casts see 3556c233d9
(qom: allow turning cast debugging off).
Reported-by: Anthony Liguori <aliguori@us.ibm.com>
Acked-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Make cpustats monitor command available unconditionally.
Prepares for changing kvm_handle_internal_error() and kvm_cpu_exec()
arguments to CPUState.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Since the ARM KVM API doesn't include a "reset this VCPU"
ioctl, we have to capture the initial values of every
register it knows about so that we can reset the VCPU
by feeding those values back again.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Convert the TCG ARM target to using an (index,value) list for migrating
coprocessors. The primary benefit of the (index,value) list is for
passing state between KVM and QEMU, but it works for TCG-to-TCG
migration as well and is a useful self-contained first step.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Port the ARM CPU save/load code to use VMState. Some state is
saved in a slightly different order to simplify things -- for
example arrays are saved one after the other rather than 'striped',
and we always save all 32 VFP registers even if the CPU happens
to only have 16.
Use one subsection for each feature. This means that we don't need to
bump the version field each time that a new feature gets introduced.
Signed-off-by: Juan Quintela <quintela@redhat.com>
[PMM: fixed conflicts, updated to use cpu_class_set_vmsd(), updated
with new/removed fields since original patch, changed to use custom
VMStateInfo for cpsr rather than presave/postload hooks, corrected
subsection names so vmload doesn't fail]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Enable ARMCPUInfo to specify a custom class_init functions.
Introduce arm_v7m_class_init() and use it for "cortex-m3" model.
Instead of forwarding from arm_cpu_do_interrupt() to do_interrupt_v7m(),
override CPUClass::do_interrupt with arm_v7m_cpu_do_interrupt()
in arm_v7m_class_init().
Acked-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Andreas Färber <afaerber@suse.de>
This removes a global per-target function and thus takes us one step
closer to compiling multiple targets into one executable.
It will also allow to override the interrupt handling for certain CPU
families.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Introduce ENV_OFFSET macros which can be used in non-target-specific
code that needs to generate TCG instructions which reference CPUState
fields given the cpu_env register that TCG targets set up with a
pointer to the CPUArchState struct.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Turn arm_cpu_realize() into a QOM realize function, no longer called
via cpu.h prototype. To maintain the semantics of cpu_init(), set
realized = true explicitly in cpu_arm_init().
Move GDB coprocessor registration, CPU reset and vCPU initialization
into the realizefn.
Signed-off-by: Andreas Färber <afaerber@suse.de>
